Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRON SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Modeling the flux of high energy negative ions during reactive magnetron sputtering

The negative ion flux during reactive sputtering from planar and rotating cylindrical magnetrons has been studied. Energy resolved mass spectrometry was used to measure the energy and mass distribution of the negative ions. Also the angular distribution of the high energy ions was characterized for planar as well as for rotating cylindrical magnetrons. Besides these measurements, a binary collision Monte Carlo simulation code, SiMTRA, was adapted in order to simulate the energy, mass, and angular distribution of the high energy negative ions. All simulated distributions, for both planar and rotating cylindrical magnetrons, were in excellent correspondence with the experimental observations. Also a model for the amount of high energy negative O{sup -} ions was proposed. Indeed, the logarithm of the amount of high energy negative O{sup -} ions is shown to be related to the secondary electron emission yield of the oxide target, and these two parameters are known to be related to the work function. The SiMTRA simulations, in combination with knowledge of the work function or secondary electron emission yield of the target, allow modeling the flux of high energy negative ions during reactive magnetron sputtering.

36 MATERIALS SCIENCE↗

Surface roughness and interface width scaling of magnetron sputter deposited Ni/Ti multilayers

Using an indigenously built r.f. magnetron sputtering system, several single layer Ti and Ni films have been deposited at varying deposition conditions. All the samples have been characterized by Grazing Incidence X-ray Reflectivity (GIXR) and Atomic Force Microscopy to estimate their thickness, density, and roughness and a power law dependence of the surface roughness on the film thickness has been established. Subsequently, at optimized deposition condition of Ti and Ni, four Ni/Ti multilayers of 11-layer, 21-layer, 31-layer, and 51-layer having different bilayer thickness have been deposited. The multilayer samples have been characterized by GIXR and neutron reflectivity measurements and the experimental data have been fitted assuming an appropriate sample structure. A power law correlation between the interface width and bilayer thickness has been observed for the multilayer samples, which was explained in the light of alternate roughening/smoothening of multilayers and assuming that at the interface the growth “restarts” every time.

36 MATERIALS SCIENCE↗

Influence of Annealing Temperature on the Microstructure and Morphology of TiN Films Synthesized by Dual Magnetron Sputtering

TiN films synthesized on leucosapphire substrates by dual magnetron sputtering have been annealed in vacuum at 600, 700, 800, and 900°C for 2 min. The microstructure and morphology of the films have been studied by X-ray diffraction and scanning electron microscopy at different temperatures. It has been found that annealing changes the microstructure, texture, grain size, and surface roughness of the TiN films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effects of substrate temperature on properties of ITO-ZnO composition spread films fabricated by combinatorial RF magnetron sputtering

We have fabricated ITO-ZnO composition spread films to investigate the effects of substrate temperature on their electrical and optical properties by using combinatorial RF magnetron sputtering. It turned out by X-ray measurement that the film with zinc contents above 16.0 at% [Zn/(In+Zn+Sn)] showed amorphous phase regardless of substrate temperature. The amorphous ITO-ZnO film had lower resistivity than polycrystalline films. When the films were deposited at 250 deg. C, the minimum resistivity of 3.0x10{sup -4} OMEGA cm was obtained with the zinc contents of 16.0 at%. The indium content could be reduced as high as {approx}30 at% compared to that of ITO for the films having similar resistivity ({approx}10{sup -4} OMEGA cm). However, a drastic increase of resistivity was observed for the ITO-ZnO films deposited at 350 deg. C, having zinc contents below 15.2 at%. - Graphical abstract: The effects of substrate temperature on properties of ITO-ZnO films were investigated by using combinatorial RF magnetron sputtering. The amorphous ITO-ZnO film had lower resistivity than polycrystalline films. The minimum resistivity of 3.0x10{sup -4} OMEGA cm was obtained with the substrate temperature of 250 deg. C and the zinc contents of 16.0 at%. The electronic states of ITO-ZnO films were discussed with related to the formation of transparent amorphous oxide semiconductor (TAOS).

36 MATERIALS SCIENCE↗

Experimental investigation of quasiperiodic-chaotic-quasiperiodic-chaotic transition in a direct current magnetron sputtering plasma

Floating potential fluctuations from a direct current magnetron sputtering plasma have been analysed using time series analysis techniques like phase space plots, power spectra, frequency bifurcation plot, etc. The system exhibits quasiperiodic-chaotic-quasiperiodic-chaotic transitions as the discharge voltage was increased. The transitions of the fluctuations, quantified using the largest Lyapunov exponent, have been corroborated by Hurst exponent and the Shannon entropy. The Shannon entropy is high for quasiperiodic and low for chaotic oscillations.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Morphology of TiN thin films grown on MgO(001) by reactive dc magnetron sputtering

Thin TiN films were grown by reactive dc magnetron sputtering on single-crystalline MgO(001) substrates at a range of temperatures from room temperature to 600 deg. C. Structural characterization was carried out using x-ray diffraction and reflection methods. TiN films grow epitaxially on the MgO substrates at growth temperatures of 200 deg. C and above. The crystal coherence length determined from Laue oscillations and the Scherrer method agrees with x-ray reflection thickness measurements to 6% and within 3% for growth temperatures of 200 and 600 deg. C, respectively. For lower growth temperatures the films are polycrystalline but highly textured and porous.

36 MATERIALS SCIENCE↗

Rotating cylindrical magnetron sputtering: Simulation of the reactive process

A rotating cylindrical magnetron consists of a cylindrical tube, functioning as the cathode, which rotates around a stationary magnet assembly. In stationary mode, the cylindrical magnetron behaves similar to a planar magnetron with respect to the influence of reactive gas addition to the plasma. However, the transition from metallic mode to poisoned mode and vice versa depends on the rotation speed. An existing model has been modified to simulate the influence of target rotation on the well known hysteresis behavior during reactive magnetron sputtering. The model shows that the existing poisoning mechanisms, i.e., chemisorption, direct reactive ion implantation and knock on implantation, are insufficient to describe the poisoning behavior of the rotating target. A better description of the process is only possible by including the deposition of sputtered material on the target.

36 MATERIALS SCIENCE↗

Effects of nitrogen ion implantation time on tungsten films deposited by DC magnetron sputtering on AISI 410 martensitic stainless steel

Nitrogen ion implantation time on tungsten thin film deposited on surface of AISI 410 steel has been performed. Tungsten thin film produced by dc magnetron sputtering method was deposited on AISI 410 martensitic stainless steel substrates, and then the nitrogen ions were implanted on tungsten thin film. The objective of this research is to investigate the effects of implantation deposition time on surface roughness, microhardness, specific wear and corrosion rate of nitrogen implanted on tungsten film. Magnetron sputtering process was performed by using plasma gas of argon (Ar) to bombardier tungsten target (W) in a vacuum chamber with a pressure of 7.6 x 10{sup −2} torr, a voltage of 300 V, a sputter current of 80 mA for sputtered time of 10 minutes. Nitrogen implantation on tungsten film was done with an initial pressure of 3x10{sup −6} mbar, a fluence of 2 x 10{sup 17} ions/cm{sup 2}, an energy of 100 keV and implantation deposition times of 0, 20, 30 and 40 minutes. The surface roughness, microhardness, specific wear and corrosion rate of the films were evaluated by surfcorder test, Vickers microhardness test, wear test and potentiostat (galvanostat) test respectively. The results show that the nitrogen ions implanted deposition time on tungsten film can modify the surface roughness, microhardness, specific wear and corrosion rate. The minimum surface roughness, specific wear and corrosion rate can be obtained for implantation time of 20 minutes and the maximum microhardness of the film is 329 VHN (Vickers Hardness Number) for implantation time of 30 minutes. The specific wear and corrosion rate of the film depend directly on the surface roughness.

36 MATERIALS SCIENCE↗

Investigation of plasma characteristics in an unbalanced magnetron sputtering system

Results are presented from experimental studies of a magnetron sputtering system for different configurations of the magnetic field above the cathode surface. The current-voltage characteristics of a magnetron discharge at different working gas pressures (0.08-0.3 Pa) and currents in the unbalancing coil were studied. The production and transport of charge carriers in a magnetron discharge with an unbalanced magnetic field was investigated by means of probe measurements of plasma characteristics and ion energies in the region between the substrate and the magnetic trap at the cathode surface. The radial distributions of the ion current density, plasma potential, and floating potential in the unbalanced operating mode are found to have pronounced extrema at the magnetron axis. It is shown that the plasma density near the substrate can be increased considerably when the axial magnetic field is high enough to efficiently confine plasma electrons and prevent their escape to the chamber wall.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Drifting localization of ionization runaway: Unraveling the nature of anomalous transport in high power impulse magnetron sputtering

The plasma over the magnetron’s erosion “racetrack” is not azimuthally uniform but concentrated in distinct dense plasma zones which move in the {vector E}×{vector B} direction with about 10% of the electrons’ {vector E}×{vector B}/B{sup 2} drift velocity. The plasma zones are investigated with a gated camera working in concert with a streak camera for Al, Nb, Cu, and W targets in Ar or Kr background gas. It is found that each plasma zone has a high density edge which is the origin of a plasma-generating electron jet leaving the target zone. Each region of strong azimuthal density gradient generates an azimuthal electric field which promotes the escape of magnetized electrons and the formation of electron jets and plasma flares. The phenomena are proposed to be caused by an ionization instability where each dense plasma zone exhibits a high stopping power for drifting high energy electrons, thereby enhancing itself.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Heteroepitaxial Ge-on-Si by DC magnetron sputtering

The growth of Ge on Si(100) by DC Magnetron Sputtering at various temperatures is studied by Spectroscopic Ellipsometry and Transmission Electron Microscopy. Smooth heteroepitaxial Ge films are prepared at relatively low temperatures of 380°C. Typical Stransky-Krastanov growth is observed at 410°C. At lower temperatures (320°C), films are essentially amorphous with isolated nanocrystallites at the Si-Ge interface. A minor oxygen contamination at the interface, developing after ex-situ oxide removal, is not seen to hinder epitaxy. Compensation of dislocation-induced acceptors in Ge by sputtering from n-doped targets is proposed.

36 MATERIALS SCIENCE↗

Electrical and optical properties of nitrogen doped SnO{sub 2} thin films deposited on flexible substrates by magnetron sputtering

Graphical abstract: The best SnO{sub 2}:N TCO film: about 80% transmittance and 9.1 × 10{sup −4} Ω cm. - Highlights: • Nitrogen-doped tin oxide film was deposited on PET by RF-magnetron sputtering. • Effects of oxygen partial pressure on the properties of thin films were investigated. • For SnO{sub 2}:N film, visible light transmittance was 80% and electrical resistivity was 9.1 × 10{sup −4} Ω cm. - Abstract: Nitrogen-doped tin oxide (SnO{sub 2}:N) thin films were deposited on flexible polyethylene terephthalate (PET) substrates at room temperature by RF-magnetron sputtering. Effects of oxygen partial pressure (0–4%) on electrical and optical properties of thin films were investigated. Experimental results showed that SnO{sub 2}:N films were amorphous state, and O/Sn ratios of SnO{sub 2}:N films were deviated from the standard stoichiometry 2:1. Optical band gap of SnO{sub 2}:N films increased from approximately 3.10 eV to 3.42 eV as oxygen partial pressure increased from 0% to 4%. For SnO{sub 2}:N thin films deposited on PET, transmittance was about 80% in the visible light region. The best transparent conductive oxide (TCO) deposited on flexible PET substrates was SnO{sub 2}:N thin films preparing at 2% oxygen partial pressure, the transmittance was about 80% and electrical conductivity was about 9.1 × 10{sup −4} Ω cm.

36 MATERIALS SCIENCE↗

Fabrication of Nb3Sn by Magnetron Sputtering for Superconducting Radiofrequency Application

Particle accelerators are considered as an important device that has wide applications in cancer treatment, sterilizing waste, preserving foods, ion implantation in semiconductor industry, and in production of isotopes for medical applications. Superconducting radiofrequency (SRF) cavities are the building blocks of a linear particle accelerator. Current particle accelerators use niobium (Nb) superconductors as the sheet material to fabricate a single SRF cavity for particle acceleration. With better superconducting properties (critical temperature Tc ~ 18.3 K, superheating field Hsh~ 400 mT), Nb3Sn is considered a potential candidate in SRF technology. Magnetron sputtering is a promising deposition method to fabricate Nb3Sn thin films inside SRF cavities. Superconducting Nb3Sn films were fabricated on Nb and sapphire substrates by magnetron sputtering from a single stoichiometric Nb3Sn target, by multilayer sputtering of Nb and Sn followed by annealing, and by co-sputtering of Nb and Sn followed by annealing. The variation of morphological and superconducting properties was investigated for different substrate temperatures, annealing temperatures, annealing durations, and thicknesses. The film properties were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and energy dispersive X-ray spectroscopy (EDS). The films had crystalline Nb3Sn structure without any presence of poor superconducting Nb6Sn5 and NbSn2 phases. The highest Tc of the films fabricated from the stoichiometric target, multilayer sputtering and co-sputtering were 17.44, 17.93, and 17.66 K respectively. Finally, a cylindrical sputter coater with two identical magnetrons was designed and commissioned to fabricate Nb3Sn films inside a 2.6 GHz SRF cavity. The magnetrons were installed facing opposite to each other in a custom designed vacuum chamber and multilayers of Nb and Sn films on 1 cm2 Nb substrates replicating the beam tubes and equator locations of the cavity and the coated multilayered films were annealed at 950 °C for 3 h. The XRD of the as?deposited and annealed films confirmed the formation of Nb3Sn after the annealing. The dissertation discusses the fabrication process, characterized results of the fabricated films, the design of the cylindrical sputter coater and the preliminary data obtained from the sputter coater.

Sayeed, Md Nizam↗

Overcoming challenges to the formation of high-quality polycrystalline TiO{sub 2}:Ta transparent conducting films by magnetron sputtering

The work is focused on understanding the physical processes responsible for the modification of the structure, electrical and optical properties of polycrystalline TiO{sub 2}:Ta films formed by annealing of initially amorphous films grown by direct current magnetron sputtering of electrically conductive ceramic targets. It is shown that fine tuning of the oxygen content during deposition of amorphous TiO{sub 2}:Ta films is critical to achieving low resistivity and high optical transmittance after annealing. Increasing the total pressure during magnetron sputter deposition is shown to decrease the sensitivity of the annealed films to the oxygen flow variation during deposition of the initially amorphous layers. Polycrystalline anatase TiO{sub 2}:Ta films of low electrical resistivity (ρ{sub H} = 1.5 × 10{sup −3}Ω cm), high free electron mobility (μ{sub H} = 8 cm{sup 2}/Vs), and low extinction (k{sub 550nm} = 0.006) are obtained in this way at a total pressure of 2 Pa. The dependence of the polycrystalline film electrical properties on the oxygen content is discussed in terms of Ta dopant electrical activation/deactivation taking into account the formation of compensating defects at different oxygen pressures. The temperature-dependent transport of the polycrystalline anatase TiO{sub 2}:Ta films is investigated showing the dominant role of the optical phonon scattering in the case of films with an optimum Ti/O ratio.

36 MATERIALS SCIENCE↗

High power pulsed magnetron sputtering: A method to increase deposition rate

High power pulsed magnetron sputtering (HPPMS) is a state-of-the-art physical vapor deposition technique with several industrial applications. One of the main disadvantages of this process is its low deposition rate. In this work, the authors report a new magnetic field configuration, which produces deposition rates twice that of conventional magnetron's dipole magnetic field configuration. Three different magnet pack configurations are discussed in this paper, and an optimized magnet pack configuration for HPPMS that leads to a higher deposition rate and nearly full-face target erosion is presented. The discussed magnetic field produced by a specially designed magnet assembly is of the same size as the conventional magnet assembly and requires no external fields. Comparison of deposition rates with different power supplies and the electron trapping efficiency in complex magnetic field arrangements are discussed.

42 ENGINEERING↗

Formation of Luminescence Spectra and Emission Intensity in the UV and Visible Spectral Regions for n-ZnO/p-GaN and n-ZnO/p-ZnO Structures when Depositing ZnO Films by High-Frequency Magnetron Sputtering

The emission spectra of structures based on ZnO films deposited by high-frequency magnetron sputtering are studied. Clearly pronounced emission lines associated with the recombination of free (λ = 363 nm) and bound excitons (λ = 377, 390, 410 nm) are observed in the PL (photoluminescence) spectra (T = 300 K) of n-ZnO/p-GaN:Mg structures, and no substantial emission is observed in the impurity PL region λ = 450–600 nm. Only emission lines characteristic of n-ZnO (λ = 374 nm) are observed in the EL (electroluminescence) spectra of n-ZnO/p-ZnO structures (T = 300 K).

36 MATERIALS SCIENCE↗

Thermal stability and tribological properties of CrZr-Si-N films synthesized by closed field unbalanced magnetron sputtering

In this work, CrZr-Si-N films with various Si contents ({<=}6.4 at. %) were synthesized by closed field unbalanced magnetron sputtering with vertical magnetron sources. The characteristics such as hardness, surface morphology, and friction coefficient of the films as a function of the Si content after annealing up to 500 degree sign C in air were evaluated. Results revealed that the as-deposited films showed very similar characteristics irrespective of the Si content. However, after annealing at 500 degree sign C, the film characteristics showed a strong dependency upon the Si content. After annealing at 500 degree sign C, the hardness of the Cr{sub 39.4}Zr{sub 12.3}N{sub 48.3} film decreased significantly to approximately 24 GPa and the surface roughness value increased approximately 3.5 times more than that of the as-deposited film. The Cr{sub 34.6}Zr{sub 10.6}-Si{sub 6.4}-N{sub 48.4} film, however, was observed to have a hardness of approximately 30 GPa, which is close to that of the as-deposited film, 32 GPa. In addition, as the wear test temperature increased from room temperature to 500 degree sign C, the average friction coefficient of the Cr{sub 39.4}Zr{sub 12.3}N{sub 48.3} film increased significantly from approximately 0.23 to 0.81, but the average friction coefficient of the Cr{sub 34.6}Zr{sub 10.6}-Si{sub 6.4}-N{sub 48.4} film was not changed extensively, measuring approximately 0.43. These results could be attributed to the improvement of the thermal stability by adding Si into the Cr-Zr-N films.

36 MATERIALS SCIENCE↗

Drifting potential humps in ionization zones: The “propeller blades” of high power impulse magnetron sputtering

Ion energy distribution functions measured for high power impulse magnetron sputtering show features, such as a broad peak at several 10 eV with an extended tail, as well as asymmetry with respect to E×B, where E and B are the local electric and magnetic field vectors, respectively. Here it is proposed that those features are due to the formation of a potential hump of several 10 V in each of the traveling ionization zones. Potential hump formation is associated with a negative-positive-negative space charge that naturally forms in ionization zones driven by energetic drifting electrons.

36 MATERIALS SCIENCE↗