Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Large-scale Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1932

The aerodynamic characteristics of eight very thick airfoils from tests in the variable density wind tunnel

Report presents the results of wind tunnel tests on a group of eight very thick airfoils having sections of the same thickness as those used near the roots of tapered airfoils. The tests were made to study certain discontinuities in the characteristic curves that have been obtained from previous tests of these airfoils, and to compare the characteristics of the different sections at values of the Reynolds number comparable with those attained in flight. The discontinuities were found to disappear as the Reynolds number was increased. The results obtained from the large-scale airfoil, a symmetrical airfoil having a thickness ratio of 21 per cent, has the best general characteristics.

Jacobs, Eastman N↗
NASA NTRS1960

Aerodynamic Characteristics of a Large-Scale Unswept Wing-Body-Tail Configuration with Blowing Applied Over the Flap and Wind Leading Edge

An investigation has been conducted in the Langley full-scale tunnel to determine the effects of a blowing boundary-layer-control lift-augmentation system on the aerodynamic characteristics of a large-scale model of a fighter-type airplane. The wing was unswept at the 70-percent- chord station, had an aspect ratio of 2.86, a taper ratio of 0.40, and 4-percent-thick biconvex airfoil sections parallel to the plane of symmetry. The tests were conducted over a range of angles of attack from approximately -4 deg to 23 deg for a Reynolds number of approximately 5.2 x 10(exp 6) which corresponds to a Mach number of 0.08. Blowing rates were normally restricted to values just sufficient to control air-flow separation. The results of this investigation showed that wing leading-edge blowing in combination with large values of wing leading-edge-flap deflection was a very effective leading-edge flow-control device for wings having highly loaded trailing-edge flaps. With leading-edge blowing there was no hysteresis of the lift, drag, and pitching-moment characteristics upon recovery from stall. End plates were found to improve the lift and drag characteristics of the test configuration in the moderate angle-of-attack range, and blockage to one-quarter of the blowing-slot area was not detrimental to the aerodynamic characteristics. Blowing boundary-layer control resulted in a considerably reduced landing speed and reduced landing and take-off distances. The ailerons were very effective lateral-control devices when used with blowing flaps.

McLemore, H. Clyde↗
NASA NTRSDate not supplied

Subscale Hardware-In-The-Loop Results for Hybrid Electric Turbofan Controls Use Cases

NASA is investigating hybrid electric turbine engine systems for commercial transport aircraft due to the potentially significant improvements hybrid electric technology offers in performance, fuel consumption, and operational and design flexibility. Recently, the technology has been tested at full scale in partnership with industry and advanced to Technology Readiness Level 4. This presentation will focus on a recent subscale hardware-in-the-loop test of an open source turbofan engine model developed by NASA. The Advanced Geared Turbofan 30,000 lbf – electrified (AGTF30-e) engine is used as a reference model to demonstrate control system design and use cases for an example mild hybrid electric system with no large-scale energy storage. This model is run in real-time in NASA’s Hybrid Propulsion Emulation Rig (HyPER) and is used to drive an emulation of the turbomachinery system using subscale electric machines. This dynamic scaled shaft emulation interacts with a subscale (<100 kW) hybrid system consisting of electric machines, motor controllers, and a programmable electronic load. Specific use cases demonstrated include the use of Turbine Electrified Energy Management to improve operation during transients, megawatt-scale power extraction from the AGTF30-e, and power transfer between engine spools. Results related to the effectiveness of hybrid systems are qualitatively compared to results from industry testing.

Hybrid↗
NASA NTRS1958

Aerodynamic Characteristics in Sideslip of a Large-Scale 49 deg Sweptback Wing-Body-Tail Configuration with Blowing Applied Over the Flaps and Wing Leading Edge

An investigation has been conducted in the Langley full-scale tunnel to determine the aerodynamic characteristics in sideslip of a large-scale 490 sweptback wing-body-tail configuration having wing leading- edge and flap-blowing boundary-layer control. The wing and tails had an aspect ratio of 3.5, a taper ratio of 0.3, and NACA 65AO06 airfoil sections parallel to the plane of symmetry. The tests were conducted over a range of angles of attack of about -5 deg to 28 deg for sideslip angles of 0 deg, -5.06 deg, -10.15 deg, and -15.18 deg. Lateral and longitudinal stability and control characteristics were obtained for6a minimized blowing rate. The Reynolds number of the tests was 5.2 x 10(exp 6), corresponding to a Mach number of 0.08. The results of the investigation showed that sideslip to angles of about -15 deg did not require, from a consideration of the longitudinal characteristics, blowing rates over the wing leading edge or flap greater than that established as minimum at zero sideslip. The optimum configuration was laterally and directionally stable through the complete lift-coefficient range including the stall; however, maximum lift for sideslip angles greater than about 50 was seriously limited by a deficiency of lateral control. Blowing over the leading edge of the retreating wing in sideslip at a rate greater than that established as minimum at zero sideslip was ineffective in improving the lateral control characteristics. The optimum configuration at zero sideslip had no hysteresis of the aerodynamic parameters upon recovery from stall.

McLemore, H. Clyde↗
NASA NTRS1973

Wind tunnel investigation of a large-scale 25 deg swept-wing jet transport model with an external blowing triple-slotted flap

An investigation has been conducted to determine the aerodynamic characteristics of a large-scale subsonic jet transport model with an externally blown triple-slotted flap. The lift of the model was augmented by the turbofan engine exhaust impingement on the flap surface. The model had a 25 deg swept wing of aspect ratio 7.28 and four turbofan engines. The model was tested with two flap extents. One extended from 0.11 to 1.00 of the wing semispan, and the other extended from 0.11 to 0.75 of the wing semispan with a single-slotted aileron from 0.75 to 1.00 of the wing semispan. The results were obtained for several flap deflections with and without the horizontal tail at gross thrust coefficients from 0 to 4.0. Longitudinal and lateral data are presented with three and four engines operating.

Aoyagi, K.↗
NASA NTRS1960

Hovering Measurements for Twin-Rotor Configurations with and Without Overlap

Results of an investigation in the Langley full-scale tunnel of the hovering performance of large-scale twin-rotor-helicopter models are presented. Measurements of thrust, torque, and rotor flapping are given for overlapped (approximately 76 percent of blade radius) and nonoverlapped configurations and for two different rotor solidities. The measured performance is compared with single-rotor measurements and with available rotor theory. These tests show that the hovering performance of a single rotor and of two rotors without overlap or vertical offset are the same and hence may be calculated by single-rotor theory. These tests in conjunction with results of previous coaxial-rotor tests show that the performance of highly overlapped rotors can be reasonably predicted by available rotor theory.

Sweet, George E.↗
NASA NTRS1972

Acoustic characteristics of large-scale STOL model at forward speed

Wind-tunnel investigations of the acoustic characteristics of the externally blown jet flap (EBF) and augmentor wing STOL concepts are dicussed. The large-scale EBF model was equipped with a triple-slotted blown by four JT15D turbofan engines with circular, coannular exhaust nozzles. The large-scale augmentor wing model was equipped with an unlined augmentor blown by a slot primary nozzle. The effects of airspeed and angle of attack on the acoustics of the EBF were small. At a forward speed of 60 knots, the impingement noise of the landing flap was approximately 2 db lower than in the static tests. Angle of attack increased the impingement noise approximately 0.1 decibels per degree. Flap deflection had a greater effect on the acoustics of the augmentor wing than did airspeed. For a nozzle pressure ratio of 1.9, the peak perceived noise level of the landing flap was 3 to 5 PNdb higher than that of the takeoff flap. The total sound power was also significantly higher for landing indicating that turning in the augmentor generated acoustic energy. Airspeed produced a small aft shift in acoustic directivity with no significant change in the peak perceived noise levels or sound power levels.

Falarski, M. D.↗
NASA NTRS1972

Large-scale wind-tunnel investigation of the noise characteristics of a semispan wing equipped with an externally blown jet flap

A wind tunnel investigation was made of the noise characteristics of a 4.42 m(14.5 foot) semispan, externally-blown jet flap model. The model was equipped with a single 76.2 cm(30 inch) diameter, ducted fan with a 1.03 pressure ratio. The effects of flap size, fan vertical location, and forward speed on the noise characteristics were studied. The data from the investigation is presented in the form of tabulated one-third octave band frequency spectrums and perceived noise levels for each test condition.

Falarski, M. D.↗
NASA NTRS1971

Detailed investigation of flowfields within large scale hypersonic inlet models

Analytical and experimental investigations were conducted to determine the characteristics of the internal flows in model passages representative of hypersonic inlets and also sufficiently large for meaningful data to be obtained. Three large-scale inlet models, each having a different compression ratio, were designed to provide high performance and approximately uniform static-pressure distributions at the throat stations. A wedge forebody was used to simulate the flowfield conditions at the entrance of the internal passages, thus removing the actual vehicle forebody from consideration in the design of the wind-tunnel models. Tests were conducted in a 3.5 foot hypersonic wind tunnel at a nominal test Mach number of 7.4 and freestream unit Reynolds number of 2,700,000 per foot. From flowfield survey data the inlet entrance, the entering inviscid and viscous flow conditions were determined prior to the analysis of the data obtained in the internal passages. Detailed flowfield survey data were obtained near the centerlines of the internal passages to define the boundary-layer development on the internal surfaces and the internal shock-wave configuration. Finally, flowfield data were measured across the throats of the inlet models to evaluate the internal performance of the internal passages. These data and additional results from surface instrumentation and flow visualization studies were utilized to determine the internal flowfield patterns and the inlet performance.

Seebaugh, W. R.↗
NASA NTRSDate not supplied

Fire-Resistant Textile Development for Exploration Vehicles With Enriched-Oxygen Cabin Environments

Material selection is a key part of the National Aeronautics and Space Administration (NASA) spacecraft fire safety management plan. Non-flammable textiles are necessary to ensure large-scale flame propagation events do not occur inside a spacecraft. An increased use of textiles and other softgood material is crucial to the pursuit of exploration spaceflight to reduce mass and volume. Exploration spaceflight missions benefit from enriched oxygen cabin environments (>21% O2) by allowing a reduced prebreathe protocol before Extravehicular Activity (EVA). However, materials become exponentially more flammable the higher the O2 levels become. Recent testing within the agency has revealed the lack of commercial-off-the-shelf (COTS) materials that can meet safety requirements in oxygen-enriched environments. Most of the fibers and textiles developed during Apollo (100% O2 cabin environment) and Skylab (>70% O2 cabin environment) are no longer commercially available due to those Programs ending and the discontinuation of raw materials or closure of the original manufacturers. As NASA returns to higher oxygen concentrations inside spacecraft, non-flammable textile development efforts have begun to meet the agency’s needs. This paper discusses those efforts including overall fire safety approach, priorities, interactions with industry, flammability testing and expected challenges.

Karim Aly↗
NASA NTRSDate not supplied

Fire-Resistant Textile Development for Exploration Vehicles With Enriched-Oxygen Cabin Environments

Material selection is a key part of the National Aeronautics and Space Administration (NASA) spacecraft fire safety management plan. Non-flammable textiles are necessary to ensure large-scale flame propagation events do not occur inside a spacecraft. An increased use of textiles and other softgood material is crucial to the pursuit of exploration spaceflight to reduce mass and volume. Exploration spaceflight missions benefit from enriched oxygen cabin environments (>21% O2) by allowing a reduced prebreathe protocol before Extravehicular Activity (EVA). However, materials become exponentially more flammable the higher the O2 levels become. Recent testing within the agency has revealed the lack of commercial-off-the-shelf (COTS) materials that can meet safety requirements in oxygen-enriched environments. Most of the fibers and textiles developed during Apollo (100% O2 cabin environment) and Skylab (>70% O2 cabin environment) are no longer commercially available due to those Programs ending and the discontinuation of raw materials or closure of the original manufacturers. As NASA returns to higher oxygen concentrations inside spacecraft, non-flammable textile development efforts have begun to meet the agency’s needs. This paper discusses those efforts including overall fire safety approach, state-of-the-art textile review and testing, an agency-wide assessment of textile needs performed by the NASA Engineering and Safety Center (NESC), the textile development strategy and expected challenges.

Mary Walker↗
NASA NTRS1961

Free-Flight Skin-Temperature and Surface-Pressure Measurements on a Highly Polished Nose Having a 100 deg Total-Angle Cone and a 10 deg Half-Angle Conical Flare Section up to a Mach Number of 4.08

The skin temperature and surface pressure were measured on a large-scale, highly polished nose having a relatively sharp-tipped 100 deg total-angle cone followed by a conical flare section of 10 deg half-angle. The measurements were obtained in flight from a rocket-propelled model up to a peak Mach number of 4.08 and a peak Reynolds number of 22 x 10(exp 6) per foot. Temperature distributions indicated that the heating on the forward 3.5 inches of the 100 deg cone was lower than the heating on the rearward portion. Likewise, measured temperatures on the flare portion of the test nose were generally lower than the temperatures on the 100 deg cone portion. The data indicated that the local Reynolds numbers of transition, based on calculated boundary-layer momentum thicknesses, ranged from 530 to 940 for a Mach number range from 2.72 to 3.75. Comparison of measured cone pressures with theory for a sharp cone showed that theory overestimates the cone pressures. Pressure measurements on the flare portion of the nose showed that in the lower speed range the flow expands below atmospheric pressure in going from the cone to the flare; however, as the speed increased, the expansion diminished and for speeds greater than a Mach number of approximately 3.0 the flare pressure coefficients were at or near a value of zero.

Rashis, Bernard↗
NASA NTRS1973

Aerodynamic characteristics of a large-scale model with a swept wing and a jet flap having an expandable duct

The data from an investigation of the aerodynamic characteristics of the expandable duct-jet flap concept are presented. The investigation was made using a large-scale model in the Ames 40- by 80-foot Wind Tunnel. The expandable duct-jet flap concept uses a lower surface, split flap and an upper surface, Fowler flap to form an internal, variable area cavity for the blowing air. Small amounts of blowing are used on the knee of the upper surface flap and the knee of a short-chord, trailing edge control flap. The bulk of the blowing is at the trailing edge. The flap could extend the full span of the model wing or over the inboard part only, with blown ailerons outboard. Primary configurations tested were two flap angles, typical of takeoff and landing; symmetric control flap deflections, primarily for improved landing performance; and asymmetric aileron and control flap deflections, for lateral control.

Aiken, T. N.↗
NASA NTRS1972

Measurements in atmospheric electricity designed to improve launch safety during the Apollo series

Ground test measurements were made during the launches of Apollo 13 and 14 in an effort to better define the electrical characteristics of a large launch vehicle. Of particular concern was the effective electrical length of the vehicle and plume since this parameter markedly affects the likelihood of a lightning stroke being triggered by a launch during disturbed weather conditions. Since no instrumentation could be carried aboard the launch vehicle, the experiments were confined to LF radio noise and electrostatic-field measurements on the ground in the vicinity of the launch pad. The philosophy of the experiment and the instrumentation and layout are described. From the results of the experiment it is concluded that the rocket and exhaust do not produce large-scale shorting of the earth's field out to distances of thousands of feet from the launch pad. There is evidence, however, that the plume does add substantially to the electrical length of the rocket. On this basis, it was recommended that there be no relaxation of launch rules for launches during disturbed weather.

Nanevicz, J. E.↗
NASA NTRS1973

Experimental investigation of a large-scale, two-dimensional, mixed-compression inlet system: Internal performance and drag at transonic conditions, free stream Mach equals 0.6 to 1.28

A large scale, variable-geometry inlet system with a design Mach number of 3.0 was tested at Mach numbers from 0.6 to 1.28. Variable features for off-design operation are an adjustable-height ramp system and a translating cowl. Experimental results are presented for transonic ramp and cowl positions showing the effect of throat boundary layer bleed and vortex generators on engine-face performance. Detailed pressure and force-balance data are used to evaluate transonic drag characteristics.

Wong, N. D.↗
NASA NTRS1973

Aspects of large-scale, subsonic, wind-tunnel design for propulsion noise research

The case for full-scale acoustic testing of propulsion systems at flight conditions and the use of wind tunnels for this work are discussed. The problems associated with measuring noise in wind tunnels are discussed, and wind-tunnel design requirements to provide a useful facility for noise research are established. Full-scale subsonic wind-tunnel designs that meet the requirements are described, and it is shown that state-of-art acoustics technology must be used in the drive-fan design to minimize background noise. If this is successfully done, acoustic treatment in the drive system area may be avoided.

Hickey, D. H.↗
NASA NTRS1973

Studies of a large-scale jet-flap rotor in the 40- by 80-foot wind tunnel

Description of a large scale rotor and its apparatus which were constructed to investigate the merits of jet-flap applications to helicopter rotors. The presented results of a wind-tunnel study, aimed at determining the jet-flap multicyclic control potential for vibratory load and stress relief, illustrate the types of control deflections involved and their effects. A demonstrated analysis technique, which is used to analyze these results, is believed to be applicable to many kinds of investigations, particularly where large numbers of variables are involved and where circumstances tend to preclude 'systematic' testing. Among the major results of the study is the finding that significant and substantial vibratory stress and load reductions are achievable with a jet-flap multicyclic control system.

Mccloud, J. L., III↗