SEARCH · Engineering Papers

Results for “LUBRICATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

NASA NTRS2014

Observations of Spacecraft Bearing Lubricant Redistribution Based on Thermal Conductance Measurements

The performance and life of precision ball bearings are critically dependent on maintaining a quantity of oil at the ball/race interface that is sufficient to support a robust protective film. In space applications, where parched conditions are intentionally the norm, harsh operating conditions can displace the small reserves of oil, resulting in reduced film thickness and premature wear. In the past, these effects have proven difficult to model or to measure experimentally. This paper describes a study addressing this challenge, where bearing thermal conductance measurements are employed to infer changes in lubricant quantity at the critical rolling interfaces. In the first part of the paper, we explain how the lubricant's presence and its quantity impacts bearing thermal conductance measurements. For a stationary bearing, we show that conductance is directly related to the lubricant quantity in the ball/race contacts. Hence, aspects of bearing performance related to oil quantity can be understood and insights improved with thermal conductance data. For a moving bearing, a different mechanism of heat transfer dominates and is dependent on lubricant film thickness on the ball. In the second part of the report, we discuss lubricant quantity observations based on bearing thermal conductance measurements. Lubricant quantity, and thus bearing thermal conductance, depends on various initial and operating conditions and is impacted further by the run-in process. A significant effect of maximum run-in speed was also observed, with less oil remaining after obtaining higher speeds. Finally, we show that some of the lubricant that is displaced between the ball and race during run-in operation can be recovered during rest, and we measure the rate of recovery for one example.

Takeuchi, Yoshimi R.↗

DOE OSTI2025

Self-Lubricating Bushing Testing for John Day Dam Ka plan Turbine Replacement

The goal of this testing program is to find suitable self-lubricated alternatives to replace the in use oil lubricated grooved-bronze bushing in Kaplan runner hubs that are currently being utilized at John Day Dam operated by the U.S. Army Corps of Engineers (USACE). Scaled bushing testing utilizing a Pacific Northwest National Laboratory designed, fabricated, and operated Bushing Test Stand under the direction and funding from USACE determined that self-lubricated bushings tested appear capable of outperforming the current oil-lubricated bronze bushings. Performance tests are focused on durability which includes cyclic load bearing properties and articulations under various loading scenarios. This testing was performed at nominally 1/5 th scale. A scaling sensitivity analysis determined that scaled testing results apply to prototypic size. This report shows the direct comparison between the current baseline bronze bushing to self-lubricated bushings from various manufacturers. Bushing data like coefficient of friction and bushing material loss (associated with bushing wear) was determined. Self-lubricated bushings tested include products manufactured specifically for hydropower applications by the following companies: Trelleborg, Kamatics, Anonymous, and Tenneco/Deva.

42 ENGINEERING↗

NASA NTRS1972

Influence of liquid lubricant properties on their performance.

The influence of lubricant properties on performance is considered in connection with various mechanisms of lubrication. The effects of temperature and pressure on viscosity, which is important in hydrodynamic and elastohydrodynamic lubrication, is presented using a correlation postulated by Roelands. Under elastohydrodynamic conditions it is important to distinguish between the influence of lubricant properties within the inlet region and the Hertz region since each performs different functions. The role of lubricant transport properties such as surface tension is considered in connection with lubricant starvation.

Wedeven, V.↗

NASA NTRS1973

Rheology in lubrication

The rheological effects on lubrication are discussed. The types of lubrication considered are thick film hydrodynamic lubrication and thin film elastohydrodynamic lubrication. The temperature-viscosity, viscoelastic, shear-thinning, and normal stess effects on the lubrication of journal bearings are analyzed. A graph of the pressure distribution of viscoelastic liquids in journal bearings is provided. Mathematical models are developed to define the effects of various properties of the lubricants on friction reduction.

Cheng, H. S.↗

NASA NTRS1975

Operating limitations of high speed jet lubricated ball bearings

A parametric study was performed with 120-mm bore angular-contact ball bearings having a nominal contact angle of 20 degrees. The bearings had either an inner- or an outer-race land riding cage, and lubrication was by recirculating oil jets which had either a single or dual orifice. Thrust load, speed, and lubricant flow rate were varied. Test results were compared with those previously reported and obtained from bearings of the same design which were under-race lubricated but run under the same conditions. Jet lubricated ball bearings were limited to speeds less than 2,500,000 DN, and bearings having inner-race land riding cages produced lower temperatures than bearings with outer-race land riding cages. For a given lubricant flow rate dual orifice jets produced lower bearing temperatures than single orifice jets, but under-race lubrication produced lower bearing temperatures under all conditions of operation with no apparent bearing speed limitation.

Zaretsky, E. V.↗

NASA NTRS1975

Operating limitations of high-speed jet-lubricated ball bearings

A parametric study was performed with 120-mm bore angular-contact ball bearings having a nominal contact angle of 20 deg. The bearings either had an inner- or an outer-race land riding cage. Lubrication was by recirculating oil jets. The oil jets either had a single or dual orifice. Thrust load, speed, and lubricant flow rate were varied. Test results were compared with those previously reported and obtained from bearings of the same design which were under-race lubricated but run under the same conditions. Jet lubricated ball bearings were limited to speeds less than 2,500,000 DN. Bearings having inner-race land riding cages produced lower temperatures than bearings with outer-race land riding cages. For a given lubricant flow rate dual orifice jets produced lower bearing temperatures than single orifice jets. However, under-race lubrication produced under all conditions of operation lower bearing temperatures with no apparent bearing speed limitation.

Zaretsky, E. V.↗

NASA NTRS1978

Emergency and microfog lubrication and cooling of bearings for Army helicopters

An analysis and system study was performed to provide design information regarding lubricant and coolant flow rates and flow paths for effective utilization of the lubricant and coolant in a once-through oil-mist (microfog) and coolant air system. A system was designed, manufactured, coupled with an existing rig and evaluation tests were performed using 46 mm bore split-inner angular-contact ball bearings under 1779N (400 lb.) thrust load. An emergency lubrication aspirator system was also manufactured and tested under lost lubricant conditions. The testing demonstrated the feasibility of using a mist oil and cooling air system to lubricate and cool a high speed helicopter engine mainshaft bearing. The testing also demonstrated the feasibility of using an emergency aspirator lubrication system as a viable survivability concept for helicopter mainshaft engine bearing for periods as long as 30 minutes.

Rosenlieb, J. W.↗

NASA NTRS1979

Determination of lubricant selection based on elastohydrodynamic film thickness and traction measurement

The project was conducted to aid in the development of an elastohydrodynamic specification for military lubricants. Experiments were conducted with a rolling disk apparatus designed to simulate a bearing or gear type contact. Measurements included lubricant film thickness, lubricant breakdown and traction for a range of loads, speeds, temperatures, and surface roughnesses. Several lubricants were used in the investigations including a traction fluid, two synthetic paraffinic lubricants and several lubricants conforming to MIL-L 7808 and 23699 specifications. Recommendations regarding an EHD specification are included.

Dow, T. A.↗

NASA NTRS1979

Wide-temperature-spectrum self-lubricating coatings prepared by plasma spraying

Self-lubricating, multicomponent coatings, which lubricate over a wide range of operating conditions, are described. The coatings were successfully applied by plasma-spraying mixed powders onto superalloy substrates. They were evaluated in friction and wear experiments, and in sliding contact bearing tests. These coatings are wear resistant by virtue of their self lubricating characteristics rather than because of extreme hardness; a further benefit is low friction. Experiments with simple pin on disk sliding specimens and oscillating plain cylindrical bearing tests were performed to evaluate the tribological properties of the coatings. It was shown that coatings of nichrome, glass and calcium fluoride are self-lubricating from about 500 to 900 C, but give high friction at the lower temperatures. The addition of silver to the coating composition improved the low temperature bearing properties and resulted in coatings which are self-lubricating from cryogenic temperatures to at least 870 C; they are therefore, wide temperature spectrum, self-lubricating compositions.

Sliney, H. E.↗

NASA NTRS1979

Wide-temperature-spectrum self-lubricating coatings prepared by plasma spraying

Self-lubricating, multicomponent coatings, which lubricate over a wide range of operating conditions, are described. The coatings have been successfully applied by plasma-spraying mixed powders onto superalloy substrates. They have been evaluated in friction and wear experiments, and in sliding contact bearing tests. These coatings are wear resistant by virtue of their self-lubricating characteristics rather than because of extreme hardness; a further benefit is low friction. Experiments with simple pin on disk sliding specimens and oscillating plain cylindrical bearing tests were performed to evaluate the tribological properties of the coatings. It was shown that coatings of nichrome, glass and calcium fluoride are self-lubricating from about 500 to 900 C, but give high friction at the lower temperatures. The addition of silver to the coating composition improved the low temperature bearing properties and resulted in coatings which are self-lubricating from cryogenic temperatures to at least 870 C; they are therefore 'wide temperature spectrum,' self-lubricating compositions.

Sliney, H. E.↗

NASA NTRS1981

Performance of jet- and inner-ring-lubricated 35 millimeter bore ball bearings operating to 2.5 million DN

Parametric tests were conducted with a 35 millimeter bore, angular contact ball bearing having a single outer land guided cage. Lubrication was achieved by flowing oil through axial grooves and radial holes machined in the inner ring of the bearing. Test conditions were a thrust load of 667 N (150 lb), shaft speeds from 48,000 to 72,000 rpm, and an oil inlet temperature of 394 K (250 F). Data from tests where the distribution of the total oil supplied to the inner ring was 50 percent for bearing lubrication and 50 percent for bearing inner ring cooling were compared with those where the distribution pattern was 25 percent lubrication and 75 percent cooling. Successful operation was experienced with both the 50-50 and 25-75 percent flow distribution patterns to 2.5 million DN. The 50-50 percent flow pattern provided the cooler bearing operation of the two inner ring lubricated bearings. The jet lubricated bearing had lower outer ring and higher inner ring temperatures than the inner ring lubricated bearings. Maximum power loss of 2.8 kW (3.7 hp) was experienced with the 25-75 percent flow distribution, and maximum percent cage slip of 7.0 occurred at 72,300 rpm with the 50-50 percent flow distribution.

Schuller, F., T.↗

NASA NTRS1981

Viscoplastic lubrication of asperities

Theoretical analyses for the lubrication of rigid wedge-shaped asperities by a viscoplastic fluid are developed for geometries in which either wedge or squeeze action are dominant. The load support in the wedge action geometry is severly limited by lubricant shear, although the squeeze geometry maintains high load support at small film thicknesses. Results suggest that in cases where macroscopic hydrodynamic lubrication is inadequate, lubricant film breakdown will be promoted by low lubricant shear strength, high sliding speed, low surface roughness, and high surface slope. In addition, results are compared with previous investigations of the factors influencing susceptibility to lubrication failure.

Sheu, S.↗

NASA NTRS1982

Lubrication of 35-millimeter-bore ball bearings of several designs at speeds to 2.5 million DN

Parametric tests were conducted with 35mm bore, angular contact ball bearings with either a single or double-outer-land-guided cage. The bearings were either lubricated by oil jets or employed inner ring lubrication. Outer ring cooling was added in selected tests. Test conditions were a radial load of 222 N (50 lb) and/or a thrust load of 667 N (150 lb), shaft speeds to 72,000 rpm, and an oil inlet temperature of 394 K (250 F). Lubricant flow to the bearing ranged rom 300 to 1900 cc/min (0.08 to 0.50 gal/min). All bearings were successfully run at speeds to 2.5 million DN. Increasing the lubricant flow decreased bearing ring temperatures but increased bearing power loss. The power loss and race temperatures of a jet lubricated bearing with double-outer-land-guided cage were always higher than those of the single-land-guided-design at similar test conditions. The lowest bearing operating temperatures were achieved when inner ring lubrication and outer ring cooling were combined. Cage slip of a double-outer-land-guided cage was approximately twice that of a single-outer-land-guided cage.

Signer, H. R.↗

NASA NTRS1983

Lubrication of 35-millimeter-bore ball bearings of several designs to 2.5 million DN

Parametric tests were conducted with 35mm bore, angular contact ball bearings with either a single or double outer and guided cage. The bearings were either lubricated by oil jets or employed inner ring lubrication. Outer ring cooling was added in selected tests. Lubricant flow to the bearing ranged from 300 to 1900 cc/min. All bearings were successfully run at speeds to 2.5 million DN. Increasing the lubricant flow decreased bearing ring temperatures but increased bearing power lines. The power loss and race temperatures of a jet lubricated with double outer land guided cage were always higher than those of the single land guided design at similar test conditions. The lowest bearing operating temperatures were achieved when inner ring lubrication and outer ring cooling were combined. It is found that cage slip of a double outer land guided cage is approximately twice that of a single outer land guided cage.

Schuller, F. T.↗

NASA NTRS1984

Elastohydrodynamic Lubrication. Status of Understanding

The development of elastohydrodynamic lubrication can be divided into three main stages. The first stage is the development of the idealized form of elastohydrodynamic lubrication, namely where the surfaces are smooth, the fluid behavior is assumed to be Newtonian, and isothermal considerations are assumed. Results based on these assumptions are presented for the complete spectrum of contact geometries (rectangular and elliptical), contact materials (hard and soft), and lubricant availability (fully flooded and starved). The status of understanding for the idealized stage of elastohydrodynamic lubrication is fairly well covered in the existing literature. The second stage of development separately incorporates the effects of a non-Newtonian fluid model, thermal effects, and surface roughness effects into the elastohydrodynamic lubrication model developed in stage 1. Results showing recent developments in this stage are presented. The third stage collectively considers the items considered in stage 2 in investigating the lubrication of real surfaces in their operating environments.

Bernard J Hamrock↗

NASA NTRS1983

Surface roughness effects with solid lubricants dispersed in mineral oils

The lubricating effectiveness of solid-lubricant dispersions are investigated in both point and line contacts using surfaces with both random and directional roughness characteristics. Friction and wear data obtained at relatively low speeds and at room temperature, indicate that the existence of solid lubricants such as graphite, MoS2, and PTFE in a plain mineral oil generally will not improve the effectiveness of the oil as a lubricant for such surfaces. Under boundary lubrication conditions, the friction force, as a function of time, initially depends upon the directional roughness properties of the contacting surfaces irrespective of whether the base oil or dispersions are used as lubricants.

Cusano, C.↗

NASA NTRS1984

Microscopic aspects of the effect of friction reducers at the lubrication limit

An attempt is made to analytically model the physicochemical properties of lubricants and their capacity to reduce friction. A technique of frozen fracturing of the lubricants was employed to study the dispersion of additives throughout a lubricant. Adsorption was observed at the liquid-solid interface, which was the region where the solid and lubricant met, and the molecular dispersion of the additive enhanced the effectiveness of the lubricant. The electrically conductive characteristics of the lubricant at the friction interface indicated the presence of tunneling effects. The Bethe model was used to examine the relationship between the coefficient of friction and the variation of interface thickness. The electron transport permitted an inelastic tunnel electron spectroscopic investigation of the molecular transformations undergone by the additive during friction episodes.

Mansot, J. L.↗

NASA NTRS1987

A review of recent advances in solid film lubrication

Thin, adherent sputtered MoS2 and ion plated metallic (Au, Ag, Pb) lubricating films are primarily used in precision contacting triboelement surfaces where wear debris formation is critical and high reliability requirements have to be satisfied. Detailed structural and compositional characterization of solid film lubricants is of prime importance. It is this information from the nano-micro-macro level which is needed to interpret and improve the frictional behavior and assure long endurance lives. The purpose of this paper is to summarize in a concise review the solid lubricant film structure and morphology and their effects on the tribological properties of the lubricant systems. The tribological performance of thin lubricating films has significantly advanced through progressive understanding of the film parameters such as adhesion, cohesion, interface formation, nucleation and microstructural growth, critical film thickness and substrate finish, and temperature. Sputtered MoS2 and ion plated Au, Ag, and Pb films are separately discussed and evaluated in terms of the above film parameters to establish the most desirable film structures and thicknesses in order to achieve effective lubrication.

Spalvins, T.↗