Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Joining”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Rotary Inertia Friction Welding of Dissimilar High-Strength 422 Martensitic Stainless Steel and 4140 Low Alloy Steel for Heavy-Duty Engine Piston Fabrication

AISI 422 martensitic stainless steel with superior high temperature performance (oxidation resistance and strength) is under evaluation for replacing current heavy-duty piston crown materials, AISI 4140 martensitic steel and micro alloyed steel (MAS) 38MnSiVS5, to fabricate a multimaterial piston. This multimaterial piston concept further improved power density and fuel economy by allowing heavyduty diesel engines to operate at higher temperatures and pressures. Joining AISI 422 steel piston crowns with AISI 4140 steel piston skirts is a key manufacturing step for this multimaterial piston. However, the significant differences in strength, elevated temperature flow stress, alloy chemistry, and temper resistance between these two martensitic steels cause some weldability issues (cracking) and metallurgical challenges (alloying element migration/segregation) when using conventional fusion-based welding processes. Rotary inertia friction welding (RIFW), a solid-state welding process, has been the preferred method to join 4140 crowns to 4140 skirts (and MAS crowns to MAS skirts) in high-volume production of current heavy-duty diesel engine pistons. It has been used to join these two materials with relatively comparable alloy chemistry to fabricate pistons with MAS skirts and 4140 crowns. Meanwhile, RIFW has also been a preferred method of dissimilar metal welding. However, RIFW of dissimilar high-strength martensitic steels has yet to be widely pursued. The interfacial microstructure complexities created by the thermomechanical process and highly nonequilibrium phase transformations during RIFW are a significant challenge for understanding and predicting their joining behavior and have not been reported in detail. Here, in this work, defect-free AISI 422 steel-AISI 4140 multimaterial pistons were successfully fabricated using the RIFW process. The interfacial microstructure and mechanical properties of dissimilar 422/4140 steel RIFW in the as-welded condition were experimentally studied in detail. The results provide critical baseline information for understanding RIFW mechanisms and guiding subsequent postweld heat treatment (PWHT) practice.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Evaluation of Corrosion and Its Impact on the Mechanical Performance of Al–Steel Joints

Aluminum–steel joints are increasingly used in the automotive industry to meet the requirements for energy saving and emission reduction. Among various joining technologies, self-pierce riveting (SPR) and resistance spot welding (RSW) are two well-established technologies for fabricating dissimilar joints with stable and high mechanical performance. However, corrosion will occur in these joints inevitably due to different electrochemical properties, which can degrade the surface quality and the mechanical performance, such as strength. This paper presents a method of understanding the corrosion mechanisms in joining aluminum and steel. For this understanding, a hybrid method combining experimental observations, mechanical properties identification, and analytical approaches was used to assess the evolution of the impact of corrosion on the joining performance, such as traction separation curves. The study was conducted on common combinations used in the vehicles, e.g., a 1.2 mm thickness aluminum alloy (AA 6022) and 2.0 mm thickness hot deep galvanized steel (HDG HSLA 340) joined by SPR and RSW. After the fabrication of these joints, accelerated cyclic corrosion tests of up to 104 cycles were performed, which reproduced the environmental conditions to which a vehicle was exposed. By investigating the microstructural evolution within the joints, the corrosion mechanisms of SPR and RSW joints were revealed, including the initiation and propagation. Moreover, the intrinsic impact of the corrosion on the mechanical performance, including the strength, axial stiffness, and crashworthiness, was analyzed by performing a lap-shear test. It showed that as corrosion proceeds, the fracture modes and mechanical performance are affected significantly.

Chemistry↗
DOE OSTI2020

Foil-based additive manufacturing system and method

An additive manufacturing system, method of manufacturing, and fabricated part. The system uses a material joining laser system to join together foil sheets to form a metal part. The material joining laser system can be configured to join adjacent foil sheets together in a substantially uniform manner. The manufacturing system also includes a material removal system that removes material from selected locations of the foil sheets to shape the foil sheets to correspond with selective slices of the part. The material removal system can be a laser system, such as a laser system configured to remove material from a foil sheet without removing material from an underlying layer. One embodiment involves the manufacture of amorphous alloy components.

Tsai, Hai-Lung↗
DOE OSTI2021

Low inductance bus assembly and power converter apparatus including the same

An apparatus, such as a power converter, includes first, second and third core bus plates arranged in parallel. The apparatus also includes a first bus extension plate joined to the first core bus plate and extending therefrom at a first angle and a second bus extension plate joined to the second core bus plate and extending therefrom at a second angle. The apparatus further includes a third bus extension plated joined with the third core bus plate and disposed parallel to the first bus extension plate and a fourth bus extension plate joined with the third core bus plate and disposed parallel to the second bus extension plate.

Nojima, Geraldo↗
DOE OSTI2021

Brazing methods using porous interlayers and related articles

The disclosure relates to a brazing method for joining substrates, in particular where one of the substrates is difficult to wet with molten braze material. The method includes formation of a porous metal layer on a first substrate to assist wetting of the first substrate with a molten braze metal, which in turn permits joining of the first substrate with a second substrate via a braze metal later in an assembled brazed joint. Ceramic substrates can be particularly difficult to wet with molten braze metals, and the disclosed method can be used to join a ceramic substrate to another substrate. The brazed joint can be incorporated into a solid-oxide fuel cell, for example as a stack component thereof, in particular when the first substrate is a ceramic substrate and the joined substrate is a metallic substrate.

Nicholas, Jason Dale↗
DOE OSTI2023

Brazing methods using porous interlayers and related articles

The disclosure relates to a brazing method for joining substrates, in particular where one of the substrates is difficult to wet with molten braze material. The method includes formation of a porous metal layer on a first substrate to assist wetting of the first substrate with a molten braze metal, which in turn permits joining of the first substrate with a second substrate via a braze metal later in an assembled brazed joint. Ceramic substrates can be particularly difficult to wet with molten braze metals, and the disclosed method can be used to join a ceramic substrate to another substrate. The brazed joint can be incorporated into a solid-oxide fuel cell, for example as a stack component thereof, in particular when the first substrate is a ceramic substrate and the joined substrate is a metallic substrate.

Nicholas, Jason Dale↗
DOE OSTI2024

Low inductance bus assembly and power converter apparatus including the same

An apparatus, such as a power converter, includes first, second and third core bus plates arranged in parallel. The apparatus also includes a first bus extension plate joined to the first core bus plate and extending therefrom at a first angle and a second bus extension plate joined to the second core bus plate and extending therefrom at a second angle. The apparatus further includes a third bus extension plated joined with the third core bus plate and disposed parallel to the first bus extension plate and a fourth bus extension plate joined with the third core bus plate and disposed parallel to the second bus extension plate.

Nojima, Geraldo↗
DOE OSTI2024

Mitigation of distortion of Al/steel part under simulated paint baking condition: Experiment and numerical model studies

Multi-material joining of lightweight structures is essential to reduce vehicle weight for more energy savings and less greenhouse gas emission. However, mismatch of thermal expansion coefficient for dissimilar materials during the paint baking process can induce part distortion and joint failure for adhesive bonding. Here, in the present work, a thermomechanical model based on contact mechanics and large deformation theory was developed for dissimilar high-strength Al alloy and steel components to study the distortion mechanism and influential factors of the residual gap. The established model was used to optimize joint conditions, such as pitch distance and part geometry. When a weld pitch is shorter than 100 mm, the maximum gap between Al and steel part can be greatly reduced to 0.1 mm, and the local stress and plastic strain around the joint during the oven heating and cooling cycle are also substantially reduced compared with the long pitch case (900 mm). The numerical modeling results revealed that a comparable bending stiffness ratio between the steel and Al cross sections is critical to the minimization of gap and distortion under paint baking condition. Digital image correlation technique was used to measure the overall part distortion and local strain distribution that were used to validate the model prediction. Weld bonding (adhesive bonding with friction bit joining) process was successfully employed to join Al to steel component without gap opening in adhesive after the paint baking and cooling.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Interlocking metasurfaces

Abstract Interlocking metasurfaces (ILMs) are architected arrays of mating features that enable joining of two bodies. Complementary to traditional joining technologies such as bolts, adhesives, and welds, ILMs combine ease of assembly, removal, and reassembly with robust mechanical properties. Structural in nature, they act in a quasi-continuous manner across a surface and enable joining of complex surfaces, e.g., lattices. In this perspective, we define an ILM, begin exploring the design domain and illustrate its breath, and pragmatically evaluate mechanical performance and manufacturability. ILMs will find applications in various fields from aerospace to micro-robotics, civil engineering, and prosthetics.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Oxidation Behavior of Welded Fe-Based and Ni-Based Alloys in Supercritical CO 2

Next-generation supercritical CO 2 (sCO 2 ) power cycles will require different classes of alloy throughout the operational temperatures to optimize tradeoff of creep strength, oxidation performance and cost. This will necessitate joining methods such as welding, which might pose compatibility concerns at the joined interfaces. In this study, similar and dissimilar metal welds were generated from a variety of candidate alloys for sCO 2 systems including ferritic/martensitic steels, austenitic steels, and Ni-based superalloys. Samples were extracted from different regions of the welds and exposed to sCO 2 at 550 °C and 20 MPa for 2500 h, then characterized to understand their behavior in this environment. Unsurprisingly, the local oxidation behavior was largely dictated by the Cr content in the underlying metal. High-Cr austenitic steels and Ni alloys formed slow-growing Cr-rich oxide scales with minimal carburization of the underlying metal, while low-Cr ferritic/martensitic steels formed fast-growing Fe-rich oxide scales with significant carburization. Most welds did not show any unusual oxidation behavior at the interfaces, considering the local Cr content. The one exception was the 347H similar metal weld, where a larger grain size and complex grain structure in the fusion zone led to a significantly higher rate of Fe-rich oxide nodule formation compared to the base metal. This suggests that microstructural changes at joined interfaces can play an important role on the oxidation-limited lifetimes in future sCO 2 systems. The composition changes across the interfaces enabled study of the effect of Fe on the growth rate of Cr-rich oxides and of the origins of the sub-surface recrystallization zone that forms beneath them.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Multi-Objective design of interlocking metasurfaces using conditional diffusion models

Unit cell design remains a major challenge for interlocking metasurfaces, a promising joining technology for dissimilar materials, due to the complex, competing, multivariate design space and the need for rapid adaptation to varying performance requirements. This study explores Conditional Diffusion Models as a design optimization tool for interlocking metasurfaces. Given the complex, competing, multivariate design space for interlocking metasurfaces, unit cell design remains a major challenge for this joining technology. We trained a conditional diffusion model on 25,000 finite element analysis-simulated interlocking metasurface unit cells to generate designs with tailored thermo-mechanical properties (tensile strength, shear strength, and thermal conductivity) based on specified performance criteria. The model demonstrated a success rate of approximately 72 % in producing designs that met specified property bounds. The conditional diffusion model generated both thermally resistive and conductive designs, revealing clear trends in design characteristics: taller, dendritic structures were advantageous for tensile loads, while shorter, robust designs excelled in shear applications. Our findings indicate that the model's performance is more influenced by the breadth of the design space than by the quantity of training data, highlighting the importance of expansive design domains for generating innovative solutions. This work establishes conditional diffusion models as a highly efficient and adaptable tool for rapid interlocking metasurface unit cell design, paving the way for advancements in multi-material joining technologies, as well as highlighting the justification to leverage conditional diffusion models as design tools across complex design domains.

Conditional diffusion models↗
DOE OSTI2026

Correlation between microstructure and residual stress formation in friction stir welded armor steels characterized by neutron diffraction

Friction stir welding (FSW) is a solid-state joining process that minimizes the heat-affected zone (HAZ) compared with fusion-based arc welding, making it well suited for joining martensitic armor steels where hardness and ballistic resistance are critical. This study investigates residual stress formation in three defect-free FSW butt-joint configurations relevant to armored-vehicle fabrication: similar rolled homogeneous armor (RHA–RHA, Case 1), similar high-hardness armor (HHA–HHA, Case 2), and dissimilar HHA–RHA (Case 3) joints produced under temperature-controlled conditions (770 °C). Neutron diffraction was employed to quantify the magnitude and spatial distribution of residual stresses in the longitudinal, transverse, and normal directions and to correlate them with weld microstructure and hardness. Tensile residual stresses were concentrated in the softened HAZ, reaching approximately 300 MPa for Case 2 and 400 MPa for Case 1 (≈50–70 % of the base-metal yield strength; ∼581 MPa for RHA and ∼566 MPa for HHA), while compressive residual stresses dominated the stir zone. The spatial extent of tensile stresses scaled with the width of the softened HAZ, which was largest in the dissimilar HHA–RHA joint and smallest in the HHA–HHA joint. Full-width-at-half-maximum (FWHM) analysis revealed low microstrain in overtempered HAZ regions and high microstrain in the stir zone associated with severe plastic deformation and fresh martensite formation. This work demonstrates that residual stress evolution in FSW of martensitic armor steels is governed not primarily by peak temperature or thermal contraction, as inferred from fusion-welding analogies, but by the competition between transformation-induced volumetric expansion and tempering-induced stress relaxation. The relative dominance of these mechanisms is shown to depend on alloy hardenability and local thermal history, leading to more extensive HAZ softening and broader tensile stress regions in the lower-hardenability RHA steel. These findings establish a transferable mechanistic framework for optimizing solid-state joining strategies in high-strength steels and other transformation-hardening alloys beyond armor applications.

Friction stir welding↗
DOE OSTI2021

Synchrotron experiment and simulation studies of magnesium-steel interface manufactured by impact welding

The effective weight reduction in the automotive industry by the wide adoption of lightweight magnesium (Mg) alloys demands high-quality joint between magnesium alloys and massively-used steels in order to wring the excess weight with strength and safety assurance. However, Mg-steel joint is difficult to achieve because there is no mutual solubility between magnesium and steel and huge disparity in physical properties. An impact-based welding method recently showed successful Mg-steel joining. In this work, the characteristics of Mg-steel interface joined by the impact welding method were investigated. Synchrotron high-energy X-ray computed tomography and diffraction were applied to characterize the microstructure across Mg-steel interface. Results revealed a deposit layer formed at the joint interface where Fe-rich particles spread deep into the Mg matrix. High-resolution 3D morphology of Mg-steel interface demonstrated the trapped pores and cracks inside the deposit layer. Finally, the formation of the deposit layer and the void/cracking evolution were analyzed by using finite element models. These findings provide insights into the immiscible Mg-steel joining process.

36 MATERIALS SCIENCE↗
DOE OSTI2023

SA508 low alloy steel to 316L stainless steel dissimilar metal joint made by powder metallurgy hot isostatic pressing

Joining ferritic SA508 low alloy steel (LAS) and austenitic 316 L stainless steel (SS) via powder metallurgy hot isostatic pressing (PM-HIP) was evaluated as an alternative method to welding. This study investigated the mechanical and microstructural evolutions of the bimetallic interface under different joint designs and heat treatments. Here, the direct joining of dissimilar metal alloys by PM-HIP method resulted in two designs: 1) powder SA508 to solid bar 316 L (P508–B316L) and 2) powder 316 L solid bar SA508 (P316L-B508). In both cases, P508–B316L and P316L-demonstrated satisfactory tensile strength, however, high hardness and severe depreciation in toughness were located on the bimetallic interface. The mechanisms responsible for the detrimental mechanical properties were verified. Large oxides were observed in P508–B316L due to the prior powder boundary (PPB) oxides present in SA508 powder. The intense sensitization occurred from the formation of M 23 C 6 carbides, consequently from the slow cooling after PM-HIP in P316L-B508. Post-HIP heat treatments were explored to reduce the distance of carbide formation; however, the heat treatment could not eliminate the carbides. The experimental results were compared to the diffusion couple simulation as a function of carbide formation with distance. The analysis also showed the high hardness at the bimetallic interface was primarily contributed by solid solution strengthening. In conclusion, the direct joining of P316L-B508 and P508–B316L via PM-HIP was deemed to be unfeasible, and a transitional material is necessary to impede the diffusion of carbon.

316L stainless Steel↗
DOE OSTI2022

Surface stress tensor and junction conditions on a rotating null horizon

The general form of the surface stress tensor of an infinitesimally thin shell located on a rotating null horizon is derived, when different interior and exterior geometries are joined there. Even though the induced metric on the surface must be the same approached from either side, the first derivatives of the metric need not be. Such discontinuities lead to a Dirac δ-distribution in the Einstein tensor localized on the horizon. For a general stationary axisymmetric geometry the surface stress tensor can be expressed in terms of two geometric invariants that characterize the surface, namely the discontinuities [κ] and [J] of the surface gravity κ and angular momentum density J. The Komar energy and angular momentum are given in coordinates adapted to the Killing symmetries, and the surface contributions to each determined in terms of [κ] and [J] . Guided by these, a simple modification of the original Israel junction conditions is verified directly from the Einstein tensor density to give the correct finite result for the surface stress, when the normal n to the surface is allowed to tend continuously to a null vector. The relation to Israel’s original junction conditions, which fail on null surfaces, is given. The modified junction conditions are suitable to the matching of a rotating “black hole” exterior to any interior geometry joined at the Kerr null horizon surface, even when the surface normal is itself discontinuous and the Barrabès-Israel formalism is also inapplicable. This joining on a rotating null horizon is purely of the matter shell type and does not contain a propagating gravitational shock wave.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

BAMCensus (The Behavior and Advanced Mobility Census Dataset Aggregator) [SWR-25-120]

This software is a high-performance tool developed in Rust for downloading and processing large-scale geospatial datasets, specifically focusing on US Census data. It is designed to address scaling limitations found in existing tools, such as R's [tidycensus](https://walker-data.com/tidycensus/), by providing performant streaming dataset JOIN operations between various US Census datasets (like ACS and LEHD) and their corresponding geometries stored on the TIGER/Lines web server. The tool automates the process of joining these data sources, returning aggregated data to the user based on a specified census GEOID type. The tool automates the process of joining these data sources, returning aggregated data to the user based on a specified census GEOID type. Its primary motivation stems from the need for a high-performance solution to combine spatial datasets with graph traversals within the context of mobility analysis tooling being developed at NREL's Behavior and Advanced Mobility (BAM) group.

Fitzgerald, Robert [National Renewable Energy Labo↗
DOE OSTI2022

Design and Optimization of Structured Multi-Functional Trapping Catalysts for Conversion of Hydrocarbons and NOx from Diesel and Advanced Combustion Engines

Oxides of nitrogen in the form of nitric oxide (NO) and nitrogen dioxide (NO 2 ) commonly referred to as NOx, is one of the two chemical precursors that lead to ground-level ozone, a ubiquitous air pollutant in urban areas. A major source of NOx is generated by equipment and vehicles powered by diesel engines, which have a combustion exhaust that contains NOx in the presence of excess O 2 . Vehicular emission control catalysts are ineffective in eliminating CO, hydrocarbons, and NOx during engine cold-start when exhaust temperatures are below 200°C. The objective of the project was to develop and demonstrate a multi-functional, catalyzed trap that enables vehicles with advanced combustion strategies to meet Tier 3 emissions standards while achieving the 150 °C challenge for sustained co-oxidation of HCs and CO and ≥90% NO trapping and release during warmup. Specifically, the multi-functional Lean HC+NOx (LHCNT) was developed for application in the exhaust aftertreatment of conventional diesel engines and engines having low temperature combustion (LTC) regimes. Activities included the design and synthesis of adsorbents and catalysts, screening and evaluation. Passive NOx absorbers (PNA), hydrocarbon (HC) traps, and oxidation catalysts (OC) were evaluated for use in series or as integrated devices. Predictive tools were developed utilizing the characterization and analysis of these materials, and an emission system was designed and optimized utilizing the catalyst systems. Microkinetic models were developed for the PNA for the simple NO-only feed and complex feed containing CO, H 2 , and model hydrocarbons (ethylene and dodecane). A first-principles, mechanistic-based model of the PNA was developed which utilized molecular-scale estimates (density functional theory) of energy barriers, mechanistic-based kinetics and realistic treatments of the flow and transport processes. Two new oxidation catalysts were developed (PdCu alloy, mixed copper-ceria-cobalt oxide), both of which significantly lessened the detrimental inhibition by CO on hydrocarbon and NO oxidation. A method for lessening the detrimental impact of CO on PNA activity was developed that involves use of an oxidation catalyst upstream of the PNA. The SwRI Ectolab TM burner system was applied to evaluate the baseline PNA material and confirmed performance comparable to the benchflow PNA studies using simulated exhaust. Spatially-resolved mass spectrometry (SpaciMS) was used to measure the transient spatial profiles of reacting species spanning the length of a three-function LHCNT containing PNA, HCT, and OC. The findings from this study provide diesel vehicle and catalyst companies valuable information to develop more cost effective emission control catalysts which helps to expand the use of more fuel efficient diesel power. The fundamental modeling and experimental tools and findings from this project can be applied to catalyst technologies used in the energy and chemical industries. The project led to 14 publications in the peer-reviewed literature with 2 additional currently under review. Finally, the project also led to training of several doctoral students who were placed in research jobs in industry and academia. Specifically, Mugdha Ambast (UH) has joined Cummins, Kevin Gu (UVa) has joined GM, and Abhay Gupta (UH) is to join Caterpillar.

02 PETROLEUM↗
DOE OSTI2022

High Efficiency InGaN LEDs Emitting in Green, Amber and Beyond (Final Report)

This project focuses on developing high efficiency light emitting diodes (LEDs) with green, amber, and longer wavelengths using two compatible material systems based on III-nitride and II-IV-nitride semiconductor heterostructures. The proposed approach uses low-indium-content InGaN and ZnGeN 2 or ZnSnN 2 heterostructure quantum wells (QWs) as the active regions for high efficiency green and amber LEDs, and therefore to advance high efficiency color-mixed white LED technology. This approach takes advantage of the increased flexibility, afforded by the incorporation of the II-IV-nitrides into the III-nitride layers, to tune the QW active region to lower the emission wavelengths and to increase the electron-hole wave function overlap. This strategy paves a new way to extend the InGaN QW LED emission wavelength without using high-indium-content InGaN. An industrially preferable metalorganic chemical vapor deposition (MOCVD) method was used to develop the growth of ZnGeN 2 and ZnSnN 2 that are compatible with the InGaN growth. The unique dual chamber MOCVD instrument at OSU was used in this project. This program created an opportunity for the two institutions (The Ohio State University and Case Western Reserve University) with complementary expertise to perform this work. Two graduate students (Md Rezaul Karim (OSU) and Benthara Hewage Dinushi Jayatunga (CWRU)) gained experience in MOCVD growth and various characterization methods including scanning electron microscopy, x-ray diffraction spectroscopy, x-ray photoemission spectroscopy, Hall measurements, cathodoluminescence and photoluminescence. Both students successfully defended their PhD dissertations in April/May 2021. Both Karim and Jayatunga have joined Intel as engineers in June/July 2021. Another two graduate students Kaitian Zhang (OSU) and Chenxi Hu (CWRU) joined the project team since spring 2021 to continue on this project. They were trained on MOCVD epitaxy of InGaN QWs and materials characterization including SEM, AFM, PL, CL, XRD, Hall measurements and electroluminescence. A third student, Vijay Gopal Thirupakuzi Vangipuram (OSU), who joined the group in fall 2021 to perform LED fabrication and characterization. The key research accomplishments of the project include: (1) Successful development of MOCVD epitaxy of single crystalline ZnGeN 2 and ZnSnN 2 . MOCVD growth parameters that determine the stoichiometry of ZnGeN 2 and ZnSnN 2 films were identified. (2) Experimentally determined the band offsets between GaN/ZnGeN 2 and GaN/ZnGaSnN 2 hetero-interfaces, which agree very well with the theoretical predictions. (3) Demonstrated the incorporation of thin ZnGeN 2 layer in InGaN QWs. Proof-of-concept of the InGaN-ZnGeN 2 QW design demonstrated as much as 80 nm of red shift without increasing In composition or QW thickness. (4) InGaN/ZnGeN 2 QWs emitting at 480 nm achieved IQE of 47%. Resulted from this project, 7 journal articles were published, and 9 conference papers were presented.

36 MATERIALS SCIENCE↗