Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “JET THRUST”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

A simulation evaluation of a four-engine jet transport using engine thrust modulation for flightpath control

The use of throttle control laws to provide adequate flying qualities for flightpath control in the event of a total loss of conventional flight control surface use was evaluated. The results are based on a simulation evaluation by transport research pilots of a B-720 transport with visual display. Throttle augmentation control laws can provide flightpath control capable of landing a transport-type aircraft with up to moderate levels of turbulence. The throttle augmentation mode dramatically improves the pilots' ability to control flightpath for the approach and landing flight condition using only throttle modulation. For light turbulence, the average Cooper-Harper pilot rating improved from unacceptable to acceptable (a pilot rating improvement of 4.5) in going from manual to augmented control. The low frequency response characteristics of the engines require a considerably different piloting technique. The various techniques used by the pilots resulted in considerable scatter in the data. Many pilots readily adapted to a good piloting technique while some has difficulty. The research demonstrates a new and viable approach to providing an independent means of redundancy or increasing the redundancy capability of transport aircraft flightpath control.

Gilyard, Glenn B.↗
NASA NTRS1983

The use of laterally vectored thrust to counter thrust asymmetry in a tactical jet aircraft

A nonlinear, six degree-of-freedom flight simulator for a twin engine tactical jet was built on a hybrid computer to investigate lateral vectoring of the remaining thrust component for the case of a single engine failure at low dynamic pressures. Aircraft control was provided by an automatic controller rather than a pilot, and thrust vector control was provided by an open-loop controller that deflected a vane (located on the periphery of each exhaust jet and normally streamlined for noninterference with the flow). Lateral thrust vectoring decreased peak values of lateral control deflections, eliminated the requirement for steady-state lateral aerodynamic control deflections, and decreased the amount of altitude lost for a single engine failure.

Source record↗
NASA NTRSDate not supplied

Study of a Plug Nozzle for Supersonic Aircraft Concepts

A plug nozzle with a cylindrical cowl is studied. The geometry is adopted following commercial supersonic aircraft concepts considered in an ongoing NASA program. For the given cowl, the plug geometry is varied that includes shapes developed by a numerical optimization study as well as porous plugs. Experimental data on noise and flow field are discussed with an eye for minimum noise at low nozzle pressure ratios (NPR2) representing landing and takeoff (LTO) conditions. NPR up to about 4.7 is covered in the experiments. Limited thrust data with accompanying numerical simulation results are also presented. Results show that a plug designed for optimum thrust at cruise is noisier while a plug designed for optimum thrust at LTO has less noise, throughout the NPR range covered. The results also show that a plug nozzle can generate transonic tones and excess broadband noise (EBBN) at lower NPR, apart from well-known screech tones and broadband shock associated noise (BBSN) at higher NPR. A long porous plug is found to effectively suppress all these aberrant noise components while suffering less than 1% loss in thrust coefficient.

Jets↗
NASA NTRS1996

Experimental and Computational Induced Aerodynamics from Missile Jet Reaction Controls at Angles of Attack to 75 Degrees

An investigation was conducted in the Langley 16-Foot Transonic Tunnel to determine induced aerodynamic effects from jet reaction controls of an advanced air-to-air missile concept. The 75-percent scale model featured independently controlled reaction jets located near the nose and tail of the model. Aerodynamic control was provided by four fins located near the tail of the model. This investigation was conducted at Mach numbers of 0.35 and 0.60, at angles of attack up to 75 deg and at nozzle pressure ratios up to 90. Jet-reaction thrust forces were not measured by the force balance but jet-induced forces were. In addition, a multiblock three-dimensional Navier-Stokes method was used to calculate the flowfield of the missile at angles of attack up to 40 deg. Results indicate that large interference effects on pitching moment were induced from operating the nose jets with the the off. Excellent correlation between experimental and computational pressure distributions and pitching moment were obtained a a Mach number of 0.35 and at angles of attack up to 40 deg.

Capone, Francis J.↗
NASA NTRS1989

Numerical study of a delta planform with multiple jets in ground effect

The flow past a 60-deg delta wing equipped with two thrust-reverser jets near the inboard trailing edge has been analyzed by numerical solution of the 3D thin-layer Navier-Stokes equations. An implicit, partially flux-split, approximately-factored Navier-Stokes solver coupled with a multiple grid embedding scheme has been adapted to this problem. Studies of the impact of numerical parameters (e.g., grid refinement and dissipation levels), and flow-field parameters such as the height of the delta wing above the ground plane and the jet size on the solution, were performed. Results of these numerical studies indicate some challenges in the accurate resolution of complex 3D free shear layers and jets. Nevertheless, flow features such as jet deformation and ground vortex formation observed in experimental flow visualizations are captured. Further, comparisons with experimental data confirm the ability to simulate the loss of wing-borne lift, commonly referred to 'suckdown, as the delta planform flies at slow speeds in close proximity to the ground. Detailed analysis of the numerical results has also given additional insight into the structure of the ground vortex and the mechanisms of lift loss.

Chawla, K.↗
NASA NTRSDate not supplied

Study of a Plug Nozzle for Supersonic Aircraft Concepts

A plug nozzle with a cylindrical cowl is studied. The geometry is adopted following commercial supersonic aircraft concepts considered in an ongoing NASA program. For the given cowl, the plug geometry is varied that includes shapes developed by a numerical optimization study as well as porous plugs. Experimental data on noise and flow field are discussed with an eye for minimum noise at low nozzle pressure ratios (NPR2) representing landing and takeoff (LTO) conditions. NPR up to about 4.7 is covered in the experiments. Limited thrust data with accompanying numerical simulation results are also presented. Results show that a plug designed for optimum thrust at cruise is noisier while a plug designed for optimum thrust at LTO has less noise, throughout the NPR range covered. The results also show that a plug nozzle can generate transonic tones and excess broadband noise (EBBN) at lower NPR, apart from well-known screech tones and broadband shock associated noise (BBSN) at higher NPR. A long porous plug is found to effectively suppress all these aberrant noise components while suffering less than 1% loss in thrust coefficient.

Jets↗
NASA NTRS2011

On INM's Use of Corrected Net Thrust for the Prediction of Jet Aircraft Noise

The Federal Aviation Administration s (FAA) Integrated Noise Model (INM) employs a prediction methodology that relies on corrected net thrust as the sole correlating parameter between aircraft and engine operating states and aircraft noise. Thus aircraft noise measured for one set of atmospheric and aircraft operating conditions is assumed to be applicable to all other conditions as long as the corrected net thrust remains constant. This hypothesis is investigated under two primary assumptions: (1) the sound field generated by the aircraft is dominated by jet noise, and (2) the sound field generated by the jet flow is adequately described by Lighthill s theory of noise generated by turbulence.

McAninch, Gerry L.↗
NASA NTRS1975

Preliminary core-engine noise abatement experimental results of a fluid injection nozzle on a JT-15D turbofan engine

Jet noise, as induced by shear stress, in an jet exhaust is investigated. Experiments were performed on a JT-15D fan jet to verify the inward momentum stress reduction concept. The experiments involved making fan air flow convergently around the high velocity core jet with a small angle. Ring airfoils were used as flow separators for the minimization of the thrust loss. Jet exhaust noise reduction of ll db at 30 deg from the jet axis was recorded and 8 db integrated overall noise reduction over a hemisphere was measured with only 4.6% thrust loss, or 152 db/percent thrust loss.

Cheng, D. Y.↗
NASA NTRS1958

Static Investigation of Paddle Vane Oscillating in Jet of 1,300-Pound-Thrust Rocket Motor

The results of a static investigation conducted to measure the normal forces on the entire jet-vane assembly and the hinge moments on the jet vane produced by a paddle vane oscillating in the jet of a 1,500-pound-thrust rocket motor are presented for vane-deflection angles from -5 deg to 25 deg. A maximum average normal force of 71 pounds with a corresponding value for maximum average hinge moment of 228 inch-pounds was obtained with the maximum area of jet vane immersed at a jet-vane angle of 25 deg decrease in thrust caused by immersion of the jet vane varied from a maximum loss of about 58 pounds, or approximately 5 percent at maximum jet-vane angle of 25 deg, to zero loss at jet-vane angles less than approximately 10 deg.

Lanford, Wade E.↗
NASA NTRS1999

Jet Spreading Increase by Passive Control and Associated Performance Penalty

This paper reviews the effects of 'screech', 'asymmetric nozzle shaping', 'tabs' and 'overexpansion' on the spreading of free jets. Corresponding thrust penalty for the tabs and overexpanded condition are also evaluated. The asymmetric shapes include rectangular ones with varying aspect ratio. Tabs investigated are triangular shaped 'delta-tabs' placed at the exit of a convergent circular nozzle. The effect of overexpansion is examined with circular convergent-divergent (C-D) nozzles. Tabs and overexpansion are found to yield the largest increase in jet spreading. Each, however, involves a performance penalty, i.e., a loss in thrust coefficient. Variation of the size of four delta-tabs show that there exists an optimum size for which the gain in jet spreading is the maximum per unit loss in thrust coefficient. With the C-D nozzles, the minimum in thrust coefficient is expected near the beginning of the overexpanded regime based on idealized flow calculations. The maximum increase in jet spreading, however, is found to occur at higher pressure ratios well into the overexpanded regime. The optimum benefit with the overexpanded flow, in terms of gain in spreading for unit penalty, is found to be comparable to the optimum tab case.

Zaman, K. B. M. Q.↗
NASA NTRS1953

Air admixture to exhaust jets

The problem of thrust increase by air admixture to exhaust jets of rockets, turbojet, ram- and pulse-jet engines is investigated theoretically. The optimum ratio of mixing chamber pressure to ambient pressure and speed range for thrust increase due to air admixture is determined for each type of jet engine.

ENGINES, PULSE-JET↗
NASA NTRS2004

An Experimental Investigation of Unsteady Thrust Augmentation Using a Speaker-Driven Jet

An experimental investigation is described in which a simple speaker-driven jet was used as a pulsed thrust source (driver) for an ejector configuration. The objectives of the investigation were twofold: first, to add to the experimental body of evidence showing that an unsteady thrust source, combined with a properly sized ejector generally yields higher thrust augmentation values than a similarly sized, steady driver of equivalent thrust. Second, to identify characteristics of the unsteady driver that may be useful for sizing ejectors, and predicting what thrust augmentation values may be achieved. The speaker-driven jet provided a convenient source for the investigation because it is entirely unsteady (having no mean component) and because relevant parameters such as frequency, time-averaged thrust, and diameter are easily variable. The experimental setup will be described, as will the various measurements made. These include both thrust and Digital Particle Imaging Velocimetry of the driver. It will be shown that thrust augmentation values as high as 1.8 were obtained, that the diameter of the best ejector scaled with the dimensions of the emitted vortex, and that the so-called Formation Number serves as a useful dimensionless number by which to characterize the jet and predict performance.

Paxson, Daniel E.↗
NASA NTRS2007

Experimental Investigation of Unsteady Thrust Augmentation Using a Speaker-Driven Jet

An experimental investigation is described in which a simple speaker-driven jet was used as a pulsed thrust source (driver) for an ejector configuration. The objectives of the investigation were twofold. The first was to expand the experimental body of evidence showing that an unsteady thrust source, combined with a properly sized ejector generally yields higher thrust augmentation values than a similarly sized, steady driver of equivalent thrust. The second objective was to identify characteristics of the unsteady driver that may be useful for sizing ejectors, and for predicting the thrust augmentation levels that may be achieved. The speaker-driven jet provided a convenient source for the investigation because it is entirely unsteady (i.e., it has no mean velocity component) and because relevant parameters such as frequency, time-averaged thrust, and diameter are easily variable. The experimental setup will be described, as will the two main measurements techniques employed. These are thrust and digital particle imaging velocimetry of the driver. It will be shown that thrust augmentation values as high as 1.8 were obtained, that the diameter of the best ejector scaled with the dimensions of the emitted vortex, and that the so-called formation time serves as a useful dimensionless parameter by which to characterize the jet and predict performance.

Paxson, Daniel E.↗
NASA NTRS2023

Flow, Noise and Thrust of Supersonic Plug Nozzles

Nozzles with internal mixers and external plugs are candidates for supersonic aircraft concepts. A fundamental experimental investigation is being conducted at NASA Glenn Research Center (GRC) to assess the optimum performance of external plugs. The focus is on noise reduction potential during landing and takeoff (LTO) operation of the aircraft while maintaining optimum thrust performance. Earlier results on flow field and noise of plug nozzles were presented in the 2022 AIAA Aeroacoustics Meeting [1]; see also [2] for a review of the plug nozzle literature.

Jets↗
NASA NTRS2024

Flow, Noise and Thrust of Supersonic Plug Nozzles

A model-scale experimental study is conducted with a plug nozzle exploring the performance of various plug geometries for supersonic aircraft concepts. All data are acquired with a given outer nozzle that is convergent and has an exit diameter of 2 inches. The shape of the centrally placed plug is varied from conic with various half-angles (lengths), to method of characteristics (MoC) designs, as well as truncated and porous geometries. Noise and schlieren flow visualization data, presented in an earlier paper, are briefly reviewed first. The focus in this paper is on the thrust performance. A newly constructed thrust stand is used to acquire data covering a nozzle pressure ratio (NPR) range from transonic (‘landing and takeoff’, LTO) to supersonic (‘cruise’) conditions. Back-to-back measurements allowed assessment of relative performance. A plug with its ‘crown’ located somewhat inside the nozzle, rather than near the exit, is found to perform better. A longer 10° plug performs better than a shorter 22° plug. A porous plug, that significantly suppresses broadband shock associated noise, is found to incur a modest thrust loss that might be an acceptable tradeoff near LTO conditions. A companion numerical simulation for some of the plug geometries yields data trends bearing reasonable agreement with the experimental results.

jets↗
NASA NTRSDate not supplied

Study of a Plug Nozzle for Supersonic Aircraft Concepts

Nozzles with external plugs are candidates for the exhaust system of supersonic aircraft concepts in an ongoing research effort at NASA. As part of that effort a fundamental study is being conducted at NASA Glenn Research Center (GRC). Experimental and limited numerical simulation results from this study, for a plug nozzle with a convergent nozzle (cowl),have been reported in recent publications[1,2]. Conventional method-of-characteristics (MoC) design for the plug requires that the flow is choked at the nozzle exit. This is why a sharp convergence of the cowl is invoked in such a design in most previous studies [3-5], leading to the earlier choice of the convergent cowl. Such a nozzle, however, is not suitable for supersonic flights because of large boat tail drag suffered by its outer surface. The boat tail drag consideration dictates that the cowl be more or less cylindrical in shape. While various other shapes have been studied in the past [6], essentially a cylindrical shape is adopted in the larger research program at NASA. The cylindrical shape has certain advantages. With the plug crown located somewhat inside the nozzle, the flow experiences convergence and divergence as with a C-D nozzle. By translating the plug, different throat-to-exit area ratio could be achieved to obtain fully expanded condition at different values of NPR. This offers a relatively easy active control strategy for the nozzle geometry throughout the flight regime from landing and takeoff (LTO) to cruise conditions. A plug nozzle model mimicking the geometry being considered in the NASA program, i.e., having a cylindrical exit, have been fabricated recently for continued fundamental studies. Some of the plugs used with the earlier convergent cowl [1] are readily adopted to this model. In addition, a few other plugs have been obtained following a numerical optimization study [7]. The various configurations are to be investigated for thrust, noise and flow fields, with complementing numerical simulations. Thrust data for a variety of configurations as well as limited noise data are in hand. Further explorations including schlieren visualization are to be conducted in the near future. The proposed paper is to summarize all these results. In the following, a few key results obtained so far are described.

jets↗