Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “JET FLAP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Numerical prediction of aeroacoustic jet-flap flows

Turbulent boundary layer flows departing an aerodynamic surface are experimentally verified to be strong sources of noise. Analysis of the source tensor of the Lighthill equation identifies important gradients of mean and fluctuating velocity components. Transition distributions of mean flow and select fluctuating velocity correlations, within the region immediately downstream of a sharp edged flap terminus are established by finite element solution of a parabolized form of the time-averaged steady flow Navier-Stokes equations closed with a turbulence kinetic energy model. Numerical solutions are presented which quantize the localized large mean flow accelerations and resultant peaks in the distribution of turbulence kinetic energy in the near wake region. Results are verified by comparison to experiment.

Baker, A. J.↗
NASA NTRS1977

Ground simulation and tunnel blockage for a swept, jet-flapped wing tested to very high lift coefficients

Ground effects experiments and large/small tunnel interference studies were carried out on a model with a 20 inch (50.8 cm) 25 degree swept wing. The wing is slatted, has a 60 degree knee-blown flap and can be fitted with unflapped tips. A tail rake of pitch-yaw probes can be fitted to the fuselage. Certain check tests were also made with a very similar straight-wing model.

Hackett, J. E.↗
NASA NTRS1979

Aerodynamic characteristics of a large-scale semispan model with a swept wing and an augmented jet flap with hypermixing nozzles

The aerodynamic characteristics of the augmentor wing concept with hypermixing primary nozzles were investigated. A large-scale semispan model in the Ames 40- by 80-Foot Wind Tunnel and Static Test Facility was used. The trailing edge, augmentor flap system occupied 65% of the span and consisted of two fixed pivot flaps. The nozzle system consisted of hypermixing, lobe primary nozzles, and BLC slot nozzles at the forward inlet, both sides and ends of the throat, and at the aft flap. The entire wing leading edge was fitted with a 10% chord slat and a blowing slot. Outboard of the flap was a blown aileron. The model was tested statically and at forward speed. Primary parameters and their ranges included angle of attack from -12 to 32 degrees, flap angles of 20, 30, 45, 60 and 70 degrees, and deflection and diffuser area ratios from 1.16 to 2.22. Thrust coefficients ranged from 0 to 2.73, while nozzle pressure ratios varied from 1.0 to 2.34. Reynolds number per foot varied from 0 to 1.4 million. Analysis of the data indicated a maximum static, gross augmentation of 1.53 at a flap angle of 45 degrees. Analysis also indicated that the configuration was an efficient powered lift device and that the net thrust was comparable with augmentor wings of similar static performance. Performance at forward speed was best at a diffuser area ratio of 1.37.

Aiken, T. N.↗
NASA NTRS1959

Preliminary Measurements of the Noise Characteristics of Some Jet-Augmented-Flap Configurations

Experimental noise studies were conducted on model configurations of some proposed jet-augmented flaps to determine their far-field noise characteristics. The tests were conducted using cold-air jets of circular and rectangular exits having equal areas, at pressure ratios corresponding to exit velocities slightly below choking. Results indicated that the addition of a flap to a nozzle may change both its noise radiation pattern and frequency spectrum. Large reductions in the noise radiated in the downward direction are realized when the flow from a long narrow rectangular nozzle as permitted to attach to and flow along a large flap surface. Deflecting or turning the jet flow by means of impingement on the under surfaces increases the noise radiated in all directions and especially in the downward direction for the jet-flap configurations tested. Turning of the flow from nozzles by means of a flap turns the noise pattern approximately an equal amount. The principle of using a jet-flap shield with flow attachment may have some application as a noise suppressor.

Maglieri, Domenic J.↗
NASA NTRS1977

Acoustic source location in the secondary mixing region of a jet-blown flap using a cross-correlation technique

An experimental investigation of the acoustic sources in the secondary mixing region of a laboratory-scale jet-flap was made using a causality correlation technique. The processed signal of a hot-film anemometer probe was cross correlated with the output signal of a far-field microphone. Axial acoustic source strength distributions were measured for three far-field microphone locations: plus or minus 45 deg in the flyover plane and 45 deg in the sideline plane. These measurements showed that the acoustic sources in the secondary mixing region are highly directional, radiating much more effectively to the -45 deg-microphone, located below the plane of the flap surface. A relative maximum in the acoustic source strength measured for the microphones in the flyover plane occurred very near the flap trailing edge, which may be due to an edge amplification effect predicted by the theoretical work of Ffowcs Williams and Hall.

Becker, R. S.↗
NASA NTRS1977

Acoustic source location in a jet-blown flap using a cross-correlation technique

The acoustic source strength distribution in a turbulent flow field was measured for two far field microphones at 45 deg above and below the plane of the flap surface. A processed signal from an inclined hot-film anemometry probe was cross correlated with the signal from the appropriate far field microphone. The contribution made by the sources associated with the fluctuating pressure on the flap surface to the sound received at far field microphone was estimated by cross correlating the processed signals of microphones which were embedded in the flap surface with the far field microphone signals. In addition, detailed fluid dynamic measurements were made in the flow field of the jet flap using dual sensor hot-film anemometry probes.

Becker, R. S.↗
NASA NTRS1961

Aerodynamic Characteristics, Temperature, and Noise Measurements of a Large-Scale External-Flow Jet-Augmented-Flap Model with Turbojet Engines Operating

An investigation has been conducted in the Langley full-scale tunnel on a large-scale model powered by turbojet engines with flattened rectangular nozzles. The wing had 35 deg. sweep of the leading edge, an aspect ratio of 6.5, a taper ratio of 0.31, and NACA 65(1)-412 and 65-408 airfoils at the root and tip. The investigation included measurements of the longitudinal aerodynamic characteristics of the model with half-span and full-span flaps and measurements of the sound pressure and skin temperature on the portions of the lower surface of the wing immersed in the jet flow. The tests were conducted over a range or angles of attack from -8 to 16 deg. for Reynolds numbers from 1.8 x 10(exp 6) to 4.4 x 10(exp 6) and a range of momentum coefficients from 0 to 2.0. In general, the aerodynamic results of this investigation made with a large-scale hot-jet model verified the results of previous investigations with small models powered by compressed-air jets. Although blowing was only done over the inboard portion of the wing, substantial amounts of induced lift were also obtained over the outboard portion of the wing. Skin temperatures were about 340 F and wing heating could be handled with available materials without cooling. Random acoustic loadings on the wing surface were high enough to indicate that fatigue failure from this source would require special consideration in the design of an external-flow jet flap system for an airplane.

Fink, Marvin P.↗
NASA NTRS1959

Low-Speed Wind-Tunnel Investigation to Determine the Aerodynamic Characteristics of a Rectangular Wing Equipped with a Full-Span and an Inboard Half-Span Jet-Augmented Flap Deflected 55 deg

An investigation to determine the aerodynamic characteristics of a rectangular wing equipped with a full-span and an inboard half-span jet-augmented flap has been made in the Langley 300 MPH 7- by 10-foot tunnel. The wing had an aspect ratio of 8.3 and a thickness-chord ratio of 0.167. A jet of air was blown backward through a small gap, tangentially to the upper surface of a round trailing edge, and was separated from the trailing edge by a very small flap at an angle of 55 deg with respect to the wing-chord plane. The results of the investigation showed that the ratio of total lift to jet-reaction lift for the wing was about 35 percent less for the half-span jet-augmented flap than for the full-span jet-augmented flap. The reduction of the span of the jet-augmented flap from full to half span reduced the maximum value of jet-circulation lift coefficient that could be produced from about 6.8 to a value of about 2.2. The half-span jet- augmented flap gave thrust recoveries considerably poorer than those obtained with the full-span jet-augmented flap. Large nose-down pitching- moment coefficients were produced by the half-span flap, with the greater part of these being the result of the larger jet reactions required to produce a given lift for the half-spin flap compared with that required for the full-span flap.

Gainer, Thomas G.↗
NASA NTRS1974

Comparison of the acoustic characteristics of large-scale models of several propulsive-lift concepts

Wind-tunnel acoustic investigations were performed to determine the acoustic characteristics and the effect of forward speed on the over-the-wing externally blown jet flap (OTW), the under-the-wing externally blown jet flap (UTW), the internally blown jet flap (IBF), and the augmentor wing (AW). The data presented represent the basic noise generated by the powered-lift system without acoustic treatment, assuming all other noise sources, such as the turbofan compressor noise, have been suppressed. Under these conditions, when scaled to a 100,000-lb aircraft, the OTW concept exhibited the lowest perceived noise levels, because of dominant low-frequency noise and wing shielding of the high-frequency noise. The AW was the loudest configuration, because of dominant high-frequency noise created by the high jet velocities and small nozzle dimensions. All four configurations emitted noise 10 to 15 PNdB higher than the noise goal of 95 PNdB at 500 ft.

Falarski, M. D.↗
NASA NTRS1961

Low-Speed Wind-Tunnel Investigation of a Reflection Plane Wing Model Equipped with Partial-Span Jet-Augmented Flaps

An investigation to determine the aerodynamic and flow-field characteristics of three 50-percent partial-span jet-augmented flap configurations located at three spanwise positions has been conducted in the Langley 300 MPH 7- by 10-foot tunnel. The model was a semispan, rectangular unswept wing with a full-span aspect ratio of 8.3 and a thickness-to-chord ratio of 0.167. The results of this investigation showed that an inboard partial-span jet-augmented flap is less effective than a full-span blowing flap. A further reduction in effectiveness is obtained as the blaring is shifted outboard along the span. At a given lift coefficient and angle of attack, the nose-down moment about the quarter chord increases as the blowing is moved outboard. This increase in nose-down moment is due primarily to the fact that the momentum coefficient must be increased in order to obtain the same lift condition. Flow surveys indicate that the tail contribution to static longitudinal stability would be greater for the outboard blowing locations.

Otis, James H., Jr.↗
NASA NTRS2008

Distributed Turboelectric Propulsion for Hybrid Wing Body Aircraft

Meeting future goals for aircraft and air traffic system performance will require new airframes with more highly integrated propulsion. Previous studies have evaluated hybrid wing body (HWB) configurations with various numbers of engines and with increasing degrees of propulsion-airframe integration. A recently published configuration with 12 small engines partially embedded in a HWB aircraft, reviewed herein, serves as the airframe baseline for the new concept aircraft that is the subject of this paper. To achieve high cruise efficiency, a high lift-to-drag ratio HWB was adopted as the baseline airframe along with boundary layer ingestion inlets and distributed thrust nozzles to fill in the wakes generated by the vehicle. The distributed powered-lift propulsion concept for the baseline vehicle used a simple, high-lift-capable internally blown flap or jet flap system with a number of small high bypass ratio turbofan engines in the airframe. In that concept, the engine flow path from the inlet to the nozzle is direct and does not involve complicated internal ducts through the airframe to redistribute the engine flow. In addition, partially embedded engines, distributed along the upper surface of the HWB airframe, provide noise reduction through airframe shielding and promote jet flow mixing with the ambient airflow. To improve performance and to reduce noise and environmental impact even further, a drastic change in the propulsion system is proposed in this paper. The new concept adopts the previous baseline cruise-efficient short take-off and landing (CESTOL) airframe but employs a number of superconducting motors to drive the distributed fans rather than using many small conventional engines. The power to drive these electric fans is generated by two remotely located gas-turbine-driven superconducting generators. This arrangement allows many small partially embedded fans while retaining the superior efficiency of large core engines, which are physically separated but connected through electric power lines to the fans. This paper presents a brief description of the earlier CESTOL vehicle concept and the newly proposed electrically driven fan concept vehicle, using the previous CESTOL vehicle as a baseline.

Kim, Hyun Dae↗
NASA NTRS1975

An experimental study of several wind tunnel wall configurations using two V/STOL model configurations

Experiments were conducted in the low speed wind tunnel using two V/STOL models, a jet-flap and a jet-in-fuselage configuration, to search for a wind tunnel wall configuration to minimize wall interference on V/STOL models. Data were also obtained on the jet-flap model with a uniform slotted wall configuration to provide comparisons between theoretical and experimental wall interference. A test section configuration was found which provided some data in reasonable agreement with interference-free results over a wide range of momentum coefficients.

Binion, T. W., Jr.↗
NASA NTRS1961

Ground Influence on a Model Airfoil with a Jet-Augmented Flap as Determined by Two Techniques

An investigation was made in the Langley 300-MPH 7- by 10-foot tunnel with a conventional ground-board setup and in the Langley tank no. 1 by using the tow carriage to move the model over a ground board to evaluate the simulation of flight conditions in ground influence with a conventional ground-board setup. The 12-percent-thick airfoil was unswept and untapered with an aspect ratio of 6.0 and had a 10 percent- chord jet-augmented flap. From this investigation it appears that the loss in lift of an airfoil with a jet-augmented flap in ground influence as determined in a wind tunnel with a conventional ground-board setup is considerably larger than would be obtained in free flight.

Turner, Thomas R.↗
NASA NTRS1984

A numerical study of the controlled flow tunnel for a high lift model

A controlled flow tunnel employs active control of flow through the walls of the wind tunnel so that the model is in approximately free air conditions during the test. This improves the wind tunnel test environment, enhancing the validity of the experimentally obtained test data. This concept is applied to a three dimensional jet flapped wing with full span jet flap. It is shown that a special treatment is required for the high energy wake associated with this and other V/STOL models. An iterative numerical scheme is developed to describe the working of an actual controlled flow tunnel and comparisons are shown with other available results. It is shown that control need be exerted over only part of the tunnel walls to closely approximate free air flow conditions. It is concluded that such a tunnel is able to produce a nearly interference free test environment even with a high lift model in the tunnel.

Parikh, P. C.↗