Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “IRIS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

High gradient off-axis coupled C-band Cu and CuAg accelerating structures

Here, we report the high gradient testing results of two single-cell off-axis coupled standing wave accelerating structures. Two brazed standing wave off-axis coupled structures with the same geometry were tested: one made of pure copper (Cu) and one made of a copper–silver (CuAg) alloy with a silver concentration of 0.08%. A peak surface electric field of 450 MV/m was achieved in the CuAg structure for a klystron input power of 14.5 MW and a 1 μs pulse length, which was 25% higher than the peak surface electric field achieved in the Cu structure. The superb high gradient performance was achieved because of the two major optimizations in the cavity's geometry: (1) the shunt impedance of the cavity was maximized for a peak surface electric field to accelerating gradient ratio of ~2 for a fully relativistic particle, and (2) the peak magnetic field enhancement due to the input coupler was minimized to limit pulse heating. These tests allow us to conclude that C-band accelerating structures can operate at peak fields similar to those at higher frequencies while providing a larger beam iris for improved beam transport.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Interpreting scattered neutron spectra on omega cryogenic implosions with measured backgrounds and higher-order scattering

Measurements of the areal density (⁠ρR⁠) of inertially confined implosions are critical to evaluate their performance. On OMEGA, ρR is inferred from measurements of the scattered neutron spectrum via neutron-time-of-flight (nTOF) and magnetic recoil spectrometer detectors. The nTOF measurements, in particular, have the ability to measure a wide range of neutron energies and thus scattering angles, with high precision. However, the neutrons that are backscattered into the detector must transit through the entire dense fuel assembly, and as a result are subject to rescattering effects, which have been heretofore neglected in the interpretation of OMEGA neutron spectra. At the backscatter edge, neglecting rescattering on OMEGA can lead to a ~10 to 20% reduction of the apparent areal density and therefore must be included in the analysis. The low ρR s on OMEGA also mean that backgrounds from non-target physics effects, such as scattering in the target chamber or slow scintillator decays, can significantly alter the measured signal. Here, we discuss how the Monte Carlo neutron spectrum postprocessor IRIS is used to include second-order scattering effects in the interpretation of the scattered neutron spectrum in OMEGA implosion experiments, and how dedicated implosion experiments are used to measure nTOF backgrounds in order to infer backscattered areal densities on OMEGA.

Deuterium↗
DOE OSTI2023

Structure studies of 13 Be from the 12 Be ⁢(𝑑,𝑝) reaction in inverse kinematics on a solid deuteron target

The low-lying structure of 13 Be has remained an enigma for decades. Despite numerous experimental and theoretical studies, large inconsistencies remain. Being both unbound and one neutron away from 14 Be, the heaviest bound beryllium nucleus, 13 Be is difficult to study through simple reactions with weak radioactive-ion beams or more complex reactions with stable-ion beams. Here, we present the results of a study using the 12 Be (𝑑,𝑝)⁢ 13 Be reaction in inverse kinematics using a 9.5 MeV per nucleon 12 Be beam from the ISAC-II facility. The solid deuteron target of IRIS was used to achieve an increased areal thickness compared to conventional deuterated polyethylene targets. The 𝑄-value spectrum below −4.4 MeV was analyzed using a Bayesian method with geant4 simulations. A three-point angular distribution with the same 𝑄-value gate was fit with a mixture of 𝑠- and 𝑝-wave, 𝑠- and 𝑑-wave, or pure 𝑝-wave transfer. The 𝑄-value spectrum was also compared with geant simulations obtained using the energies and widths of states reported in four previous works. As a result, it was found that our results are incompatible with works that revealed a wide 5/2 + resonance but shows better agreement with ones that reported a narrower width.

6 ≤ A ≤ 19↗
DOE OSTI2024

High-Throughput Data Processing at FRIB Using ESnet

Real-time or nearly real-time (nearline) data processing methods are critical tools as detector technologies and data acquisition (DAQ) systems allow for higher data rates and volumes. The introduction of the energy sciences network (ESnet), a U.S. Department of Energy (DOE) supported high-speed network for scientific research, creates opportunities to leverage the computing power of DOE facilities like the National Energy Research Scientific Computing Center (NERSC). As a first step toward realizing a DOE Office of Science Integrated Research Infrastructure (IRI) pattern, an automated workflow was developed to remotely process data obtained from a nuclear physics experiment at the Facility for Rare Isotope Beams (FRIB) at NERSC with data transferred between FRIB and NERSC over ESnet. The workflow demonstrated the ability to process one week’s worth of experimental data in approximately 90 min and was used successfully for nearline analysis during a recently completed FRIB experiment. Here, a summary of the workflow development and results of recent demonstrations will be presented.

Data processing↗
DOE OSTI2021

Training Spiking Neural Networks with Synaptic Plasticity under Integer Representation

Neuromorphic computing is emerging as a promising Beyond Moore computing paradigm that employs event-triggered computation and non-von Neumann hardware. Spike Timing Dependent Plasticity (STDP) is a well-known bio-inspired learning rule that relies on activities of locally connected neurons to adjust the weights of their respective synapses. In this work, we analyze a basic STDP rule and its sensitivity on the different hyperparameters for training spiking neural networks (SNNs) with supervision, customized for a neuromorphic hardware implementation with integer weights. We compare the classification performance on four UCI datasets (iris, wine, breast cancer and digits) that depict varying levels of complexity. We perform a search for optimal set of hyperparameters using both grid search and Bayesian optimization. Through the use of Bayesian optimization, we show the general trends in hyperparameter sensitivity in SNN classification problem. With the best sets of hyperparameters, we achieve accuracies comparable to some of the best performing SNNs on these four datasets. With a highly optimized supervised STDP rule we show that these accuracies can be achieved with just 20 epochs of training.

Kulkarni, Shruti↗
DOE OSTI2023

CHARM-SYCL: New Unified Programming Environment for Multiple Accelerator Types

Addressing performance portability across diverse accelerator architectures has emerged as a major challenge in the development of application and programming systems for high-performance computing environments. Although recent programming systems that focus on performance portability have significantly improved productivity in an effort to meet this challenge, the problem becomes notably more complex when compute nodes are equipped with multiple accelerator types—each with unique performance attributes, optimal data layout, and binary formats. To navigate the intricacies of multi-accelerator programming, we propose CHARM-SYCL as an extension of our CHARM multi-accelerator execution environment [27]. This environment will combine our SYCL-based performance-portability programming front end with a back end for extremely heterogeneous architectures as implemented with the IRIS runtime from Oak Ridge National Laboratory. Our preliminary evaluation indicates potential productivity boost and reasonable performance compared to vendor-specific programming system and runtimes.

Fujita, Norihisa↗
DOE OSTI2026

The LCLStream Ecosystem for Multi-Institutional Dataset Exploration

We describe a new end-to-end experimental data streaming framework designed from the ground up to support new types of applications – AI training, extremely high-rate X-ray time-of-flight analysis, crystal structure determination with distributed processing, and custom data science applications and visualizers yet to be created. Throughout, we use design choices merging cloud microservices with traditional HPC batch execution models for security and flexibility. This project makes a unique contribution to the DOE Integrated Research Infrastructure (IRI) landscape. By creating a flexible, API-driven data request service, we address a significant need for high-speed data streaming sources for the X-ray science data analysis community. With the combination of data request API, mutual authentication web security framework, job queue system, high-rate data buffer, and complementary nature to facility infrastructure, the LCLStreamer framework has prototyped and implemented several new paradigms critical for future generation experiments.

Rogers, David [ORNL] (ORCID:0000000251871768)↗
DOE OSTI2023

Challenges in correlating oxygen stable isotope ratios of hydrates on uranium ore concentrates to process waters

Exchange of oxygen stable isotopes (δ 18 O values) between precipitation waters and uranium oxides is governed by thermodynamics or kinetics. It has been assumed that meteoric waters can be related to precipitation waters in uranium ore concentrates and their calcination and reduced uranium oxide products. With this assumption, the δ 18 O values of uranium materials could provide forensic signatures that identify the production history and geolocation of nuclear materials. To further exploit the potential of δ 18 O values in nuclear material analysis, this study examines the oxygen stable isotope exchange in two UOCs, magnesium diuranate (MDU) and sodium diuranate (SDU). MDU and SDU were synthesized from solutions of uranyl nitrate hexahydrate using precipitation waters with unique oxygen isotope compositions. The structures of the MDU and SDU were analyzed using powder X-ray diffraction (p-XRD) and thermal mass loss curves, while the δ 18 O values of waters generated during thermal decomposition were analyzed using a thermogravimetric analyzer coupled to an isotope ratio infrared spectrometer (TGA-IRIS). By p-XRD, the MDU was uniform and amorphous across all syntheses with residual crystalline material incorporated as a minor component. Combined with the TGA results, all of the MDU is likely amorphous MgU 2 O 7 ·3H 2 O with MgO impurities present throughout. In contrast, the SDU synthesis resulted in multiple phases with many samples exhibiting crystalline phases including a combination of Na(UO 2 ) 4 O 2 (OH) 5 ·5H 2 O and Na 2 (UO2) 6 O 4 (OH) 6 ·8H 2 O with a Na 2 U 2 O 7 minor phase. A small fraction of the SDU samples were amorphous with no crystalline XRD peaks observed. Mass loss curves of the SDU samples revealed that the amorphous samples contained inclusions of similar crystalline phases compared to the crystalline materials. The uniformity of the MDU samples enabled highly reproducible measurements of δ 18 O values of the water vapor yielded for two dehydration events at 170 °C and 500 °C. In contrast, the multiphase composition of the SDU samples resulted in poor reproducibility in δ 18 O values. In conclusion, neither system revealed any correlation between the δ 18 O values of precipitation water, and the waters released during dehydration of the UOCs.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2020

Materials Data on YIr by Materials Project

IrY is Tetraauricupride structured and crystallizes in the cubic Pm-3m space group. The structure is three-dimensional. Y is bonded in a body-centered cubic geometry to eight equivalent Ir atoms. All Y–Ir bond lengths are 2.98 Å. Ir is bonded in a body-centered cubic geometry to eight equivalent Y atoms.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Plasma Processing of SRF Cavities for the Next Generation of Particle Accelerators

What are the major goals of the project? Goal 1: Optimize interactively processing of the single-cell cavity by combining plasma treatment and vertical cold bath testing. Continue using single cell cavity as the test bed for new applications. Goal 2: Work on upgrading the plasma etching technology for multi-cell SRF cavities. Goal 3: Develop and adapt discharge configurations to critical cavity regions including the electron beam weld (EBW) and iris areas. Goal 4: Develop tailored methods to prepare surface properties for a specific function prior to any additional modification, such as (but not limited to) surface passivation in preparation of other superconducting materials and structures.

43 PARTICLE ACCELERATORS↗
DOE OSTI2020

System Study: Emergency Power System 1998–2018

This report presents an unreliability evaluation of the emergency power system (EPS) at 104 U.S. commercial nuclear power plants. Demand, run hours, and failure data from 1998 through 2018 for selected components were obtained from the Institute of Nuclear Power Operations (INPO) Industry Reporting and Information System (IRIS), formerly the INPO Consolidated Events Database (ICES). The unreliability results are trended for the most recent 10 year period while yearly estimates for system unreliability are provided for the entire active period. No statistically significant increasing or decreasing trends were identified in the EPS results.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

System Study: Residual Heat Removal 1998–2018

This report presents an unreliability evaluation of the residual heat removal (RHR) system in two modes of operation (low-pressure injection in response to a large loss-of-coolant accident and post-trip shutdown-cooling) at 104 U.S. commercial nuclear power plants. Demand, run hours, and failure data from calendar years 1998 through 2018 for selected components were obtained from the Institute of Nuclear Power Operations (INPO) Industry Reporting and Information System (IRIS), formerly the INPO Consolidated Events Database (ICES). The unreliability results are trended for the most recent 10 year period while yearly estimates for system unreliability are provided for the entire active period. No statistically significant increasing or decreasing trends were identified in the RHR results.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2020

Infrasound Needs from a Future Geophysical Facility

Since the start of the SAGE/GAGE era, infrasound has become increasingly popular as both dedicated infrasound deplayments or coupled with other geophysical sensors for monitoring and research purposes, with interdisciplinary applications in both Earth and Atmospheric science. Infrasound can be used to study and monitor a variety of hazards that occur at or near the surface, including volcanic eruptions, earthquakes, and rapid gravity-driven mass movements. Because of this, it can help address some of the questions raised by recent community vision initiatives such as SZ4D (increase the understanding of the processes underlying subduction geohazards) and ERUPT (further our understanding of volcanic systems to help inform eruption forecasting). Many of the recommendations included here are topics of focus at workshops and conferences, including most recently at the November 2019 CONVERSE infrasound workshop. As NSF plans the successor to SAGE/GAGE, we advocate including infrasound in addition to the already-supported fields of seismology and geodesy. The two main features that we would like to see in the new facility are: 1) a community pool of infrasound instrumentation, and 2) the continuation and expansion of data management resources provided by the IRIS DMC.

58 GEOSCIENCES↗
DOE OSTI2020

Identifying Suspect Instrument Intervals Using Midnight Noise Time Histories

With an intense work ethic, and high levels of devotion to their craft, seismologists continue to battle the elements and wrestle with complex logistics in their efforts to field instrumentation over the entire globe. We are fortunate to see data volumes accelerating in size, and quality continuing to improve; for example, universal timing issues can now be considered rare. However, instrument response issues are still common, and can hinder research that seeks to understand amplitudes of seismic wavefields. We are interested in using the accumulations of seismic data to develop models that will predict high frequency (0.2-20 Hz, and higher) signal amplitudes for explosion monitoring purposes over broad areas, which requires large data sets and extensive quality control. To identify response and station health issues, we have collected noise time histories for global seismic data, focusing on measurements near (but not restricted to) midnight to eliminate diurnal variations, and have manually determined time intervals that appear inconsistent with background behavior. We assign descriptive labels, but do not attempt to diagnose causes. We use these intervals to discard data. To date, we have examined 39,260 channels from 11,105 stations, heavily weighted toward IRIS holdings, dates through 2017 (depending on station, roughly the date we started our manual review), bands between 1 and 8 Hz, finding 24,733 anomalous time intervals. The great majority (90%) of these intervals appear to be shifts of constant offset, often bounded by times of known instrument changes, likely the result of poor documentation of response parameters at one of many stages between the field and the plotter. We hope these results can be of use to our colleagues, and would encourage community efforts to diagnose anomalous behavior, and fix poor responses. We also hope these results will support automation efforts, including application of supervised learning techniques.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Open Data for Nuclear Explosion Monitoring (NEM) [Slides]

The data sources tend to have the highest quality data and metadata, particularly for more recent data sets. Early data from sources such as IRIS tend to have some metadata issues.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2021

Computational Fluid Dynamic Simulation for Electrolyte Flow in Horizontal EP of Nb SRF Elliptical Cavities

An electrolyte flow velocity on an electropolishingsurface affects a material removal rate where higherremoval is observed with a higher velocity of theelectrolyte. In horizontal EP (HEP) of an ellipticalcavity, an electrolyte flow near the equator positionmight remain slow and responsible for a lowerremoval compared to that on the iris and beam pipepositions. In order to understand the flow dynamicon an elliptical cavity surface in the horizontal EPprocess, a computational fluid dynamic simulationwas conducted. This study was conducted on 1.3GHz cavity with different cathodes and acid flowrates. Final aim of the study is to improve the flowuniformity to attain uniform removal especially inmulticell cavities.

Chouhan, V.↗
DOE OSTI2022

Enhanced Component Performance Study: Air-Operated Valves 1998–2020

This report presents an enhanced performance evaluation of air-operated valves (AOVs) at U.S. commercial nuclear power plants. The data used in this study are based on the operating experience failure reports from calendar year 1998 through 2020 as reported in the Institute of Nuclear Power Operations (INPO) Industry Reporting and Information System (IRIS). The AOV failure modes considered are failure-to-open/close (FTOC), failure to operate or control (FTOP), and spurious operation (SO). The component reliability estimates and the reliability data are trended for the most recent 10-year period while yearly estimates for reliability are provided for the entire study period. The following trends were identified for the most recent 10-year period: o Extremely statistically significant increasing trend for the frequency of FTOC demands (demands per reactor year) for low-demand (= 20 demands per year) AOVs o Extremely statistically significant increasing trend for the frequency of FTOC demands for high-demand (> 20 demands per year) AOVs o Highly statistically significant decreasing trend for the failure rate of FTOP for low-demand AOVs o Highly statistically significant decreasing trend for the frequency of FTOP events (failures per reactor year) for low-demand AOVs o Statistically significant decreasing trend for the failure rate of SO for low-demand AOVs o Statistically significant decreasing trend for the frequency of SO events (failures per reactor year) for low-demand AOVs.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2022

System Study: Auxiliary Feedwater 1998-2020

This report presents an unreliability evaluation of the auxiliary feedwater (AFW) system at 69 U.S. commercial nuclear reactors. Demand, run hour, and failure data from calendar year 1998–2020 for selected components were obtained from the Institute of Nuclear Power Operations (INPO) Industry Reporting and Information System (IRIS), formerly the INPO Consolidated Events Database (ICES). The unreliability results are trended for the most recent 10-year period while yearly estimates for system unreliability are provided for the entire active period. Statistically significant decreasing trends were identified in the industry-wide estimates of AFW system start-only unreliability and AFW system 8-hour mission unreliability.

99 GENERAL AND MISCELLANEOUS↗