SEARCH · Engineering Papers

Results for “Hollow structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

NASA NTRS1971

Boron epoxy reinforced structural sections.

A NASA Research program on the development of lightweight aluminum stiffening sections will be reviewed. The sections under investigation are hollowed extrusions which have been reinforced with boron epoxy by means of a fiber infiltration scheme being developed by Avco. Advantages of this type of construction are cost, environmental stability, manufacturing flexibility, and simplicity in joining. Present studies are focused on developing and verifying structural concepts for stiffener sections for compression panels. Results of analytical studies to size boron reinforcement will be discussed. Compression test results on stiffener sections will be presented and the design of a large compression panel will be reviewed. Results from compression panel efficiency studies indicate that panels with infiltrated stiffeners may be as much as 25% lighter than comparable all aluminum panels.-

Roy, P. A.↗

NASA NTRS1993

A hydrodynamic model of the oscillating screen viscometer

The viscometer consists of an oscillating screen immersed in a fluid and free to rotate about an axis in its plane. The viscosity can be determined from the measured ratio of the periodic driving force to the screen motion when an adequate hydrodynamical model of the immersed oscillator is available. The screen is formed by a square mesh of thin wire whose dimensions invite comparison with asymptotic results for narrow hollow bodies translating in Stokes flow. These indicate that the closed hole structure of the grid plays an important role in determining its motion. It is shown that this role diminishes as the frequency increases. The computed results, obtained from a system of linear equations, are consistent with experimental values over the appropriate range of frequency.

Davis, A. M. J.↗

NASA NTRS1994

Thermal/structural Tailoring of Engine Blades (T/SEAEBL). Theoretical Manual

The Thermal/Structural Tailoring of Engine Blades (T/STAEBL) system is a family of computer programs executed by a control program. The T/STAEBL system performs design optimizations of cooled, hollow turbine blades and vanes. This manual describes the T/STAEBL data block structure and system organization. The approximate analysis and optimization modules are detailed, and a validation test case is provided.

Brown, K. W.↗

NASA NTRS1997

Space Station Cathode Ignition Test Status at 32,000 Cycles

A plasma contactor system has been baselined for the International Space Station for structural potential control. An ignition procedure was developed for the plasma contactor hollow cathode assembly (HCA). To demonstrate the required 99% HCA ignition reliability over 6,000 cycles, an ignition test was conducted. An accelerated test procedure was employed to rapidly accumulate ignition cycles. The test procedure minimized the differences between accelerated and non-accelerated test results. The development HCA used in this test has achieved 32,000 ignitions to date. The HCA has been qualified for cyclic operation, which could reduce xenon consumption and extend the life of the plasma contactor system.

Zakany, James S.↗

NASA NTRS1994

Effects of Ice-Crystal Structure on Halo Formation: Cirrus Cloud Experimental and Ray-Tracing Modeling Studies

During the 1986 Project FIRE (First International Satellite Cloud Climatology Project Regional Experiment) field campaign, four 22 deg halo-producing cirrus clouds were studied jointly from a ground-based polarization lidar and an instrumented aircraft. The lidar data show the vertical cloud structure and the relative position of the aircraft, which collected a total of 84 slides by impaction, preserving the ice crystals for later microscopic examination. Although many particles were too fragile to survive impaction intact, a large fraction of the identifiable crystals were columns and radial bullet rosettes, with both displaying internal cavitations and radial plate-column combinations. Particles that were solid or displayed only a slight amount of internal structure were relatively rare, which shows that the usual model postulated by halo theorists, i.e., the randomly oriented, solid hexagonal crystal, is inappropriate for typical cirrus clouds. With the aid of new ray-tracing simulations for hexagonal hollow-ended column and bullet-rosette models, we evaluate the effects of more realistic ice-crystal structures on halo formation and lidar depolarization and consider why the common halo is not more common in cirrus clouds.

Sassen, Kenneth↗

NASA NTRSDate not supplied

Novel Deployable Sunshade for a Formation-Flying Telescope

- Deployable sunshade is based on folding paper party decoration. - Cellular structure creates strong, rigid form. - Instead of folding flat, the cellular fan is wrapped around a central hollow core to accommodate a focusing optic. - Imbedded spring ribs deploy the cellular fan into a large disk. - Shade is constructed of thermal blanket materials and is sewn together rather than glued. - Design bears some resemblance to JPL starshade, but is a much simpler design - JPL design includes pantograph-like mechanical structure and motors to drive deployment.

Anne-Marie Novo-Gradac↗

NASA NTRS1990

The formation and structure of circumstellar and interstellar dust

The intriguing abundance of long linear carbon chain molecules in some dark clouds and in circumstellar shells is still not well understood. Recent laboratory studies which have probed this problem indicate that when carbon vapor nucleates to form particles, linear chains and hollow cage molecules (fullerenes) also form at more-or-less the same time. The results have consequences for the formation, structures and spectroscopic properties of the molecular and dust components ejected from cool carbon-rich stars. A most interesting result of the experimental observations relates to the probability that a third character in addition to the chains and grains, the C(sub 60) molecule probably in the form of the ion C(sub 60)(sup +) in the less shielded regions, is present and perhaps responsible for some of the ubiquitously observed interstellar spectroscopic features such as the Diffuse Interstellar Features, the 2170A UV Absorption or perhaps some of the Unidentified Infrared Bands. Further study of small carbon particles which form in the gas phase has resulted in the discovery that they have quasi-icosahedral spiral shell structures. The role that such species may play in the interstellar medium as well as that played by C(sub 60) (or C sub 60 sup +) should soon be accessible to verification by a combination of laboratory experiment and astronomical spectroscopy.

Kroto, H. W.↗

NASA NTRS1983

Non-invasive method and apparatus for measuring pressure within a pliable vessel

A non-invasive method and apparatus is disclosed for measuring pressure within a pliable vessel such as a blood vessel. The blood vessel is clamped by means of a clamping structure having a first portion housing a pressure sensor and a second portion extending over the remote side of the blood vessel for pressing the blood vessel into engagement with the pressure sensing device. The pressure sensing device includes a flat deflectable diaphragm portion arranged to engage a portion of the blood vessel flattened against the diaphragm by means of the clamp structure. In one embodiment, the clamp structure includes first and second semicylindrical members held together by retaining rings. In a second embodiment the clamp structure is of one piece construction having a solid semicylindrical portion and a hollow semicylindrical portion with a longitudinal slot in the follow semicylindrical portion through which a slip the blood vessel. In a third embodiment, an elastic strap is employed for clamping the blood vessel against the pressure sensing device.

Shimizu, M.↗

NASA NTRS2010

Compliant, low profile, independently releasing, non-protruding and genderless docking system for robotic modules

An apparatus for coupling with a mating coupling module to facilitate the joining of two disjoined structures without requiring precise alignment between the disjoined structures during the coupling of them may include a rotating drive mechanism, a hollow cylindrical body operatively connected to the rotating drive mechanism, wherein the hollow cylindrical body has at least one internal spiral channel, and at least one connector claw positioned within the hollow cylindrical body and guided by the internal spiral channel, wherein the at least one connector claw is configured to extend outwardly from the coupling module to engage the mating coupling module when brought in close proximity but not necessarily in precise alignment with the mating coupling module.

Khoshnevis, Behrokh↗

NASA NTRS2012

Corner-Cube Retroreflector Instrument for Advanced Lunar Laser Ranging

A paper describes how, based on a structural-thermal-optical-performance analysis, it has been determined that a single, large, hollow corner cube (170- mm outer diameter) with custom dihedral angles offers a return signal comparable to the Apollo 11 and 14 solid-corner-cube arrays (each consisting of 100 small, solid corner cubes), with negligible pulse spread and much lower mass. The design of the corner cube, and its surrounding mounting and casing, is driven by the thermal environment on the lunar surface, which is subject to significant temperature variations (in the range between 70 and 390 K). Therefore, the corner cube is enclosed in an insulated container open at one end; a narrow-bandpass solar filter is used to reduce the solar energy that enters the open end during the lunar day, achieving a nearly uniform temperature inside the container. Also, the materials and adhesive techniques that will be used for this corner-cube reflector must have appropriate thermal and mechanical characteristics (e.g., silica or beryllium for the cube and aluminum for the casing) to further reduce the impact of the thermal environment on the instrument's performance. The instrument would consist of a single, open corner cube protected by a separate solar filter, and mounted in a cylindrical or spherical case. A major goal in the design of a new lunar ranging system is a measurement accuracy improvement to better than 1 mm by reducing the pulse spread due to orientation. While achieving this goal, it was desired to keep the intensity of the return beam at least as bright as the Apollo 100-corner-cube arrays. These goals are met in this design by increasing the optical aperture of a single corner cube to approximately 170 mm outer diameter. This use of an "open" corner cube allows the selection of corner cube materials to be based primarily on thermal considerations, with no requirements on optical transparency. Such a corner cube also allows for easier pointing requirements, because there is no dependence on total internal reflection, which can fail off-axis.

Turyshev, Slava G.↗

NASA NTRS1991

Velocity structure of the ring nebula around supernova 1987A

A series of high-resolution spectra of the pc-sized nebula around SN1987A are presented. The hollow, 1.7 arcsec-wide nebula has the velocity field of a ring expanding at 10.3 km/s, not that of a limb-brightened spheroid. Fainter nebulosity within 3 arcsec is expanding slightly faster, as indicated by redshifted emission from behind the SN. The geometry of the emission can be used to infer structure, provided that light travel time and recombination delays are accounted for. The analysis sets an upper limit to the velocity of the wind from the progenitor during its red supergiant (RGS) phase, and implies an RSG lifetime of less than 400,000 yr and an interval of about 20,000 yr between the end of the RSG phase and the SN explosion.

Crotts, Arlin P.↗

NASA NTRS1974

Design and fabrication of a boron reinforced intertank skirt

Analytical and experimental studies were performed to evaluate the structural efficiency of a boron reinforced shell, where the medium of reinforcement consists of hollow aluminum extrusions infiltrated with boron epoxy. Studies were completed for the design of a one-half scale minimum weight shell using boron reinforced stringers and boron reinforced rings. Parametric and iterative studies were completed for the design of minimum weight stringers, rings, shells without rings and shells with rings. Computer studies were completed for the final evaluation of a minimum weight shell using highly buckled minimum gage skin. The detail design is described of a practical minimum weight test shell which demonstrates a weight savings of 30% as compared to an all aluminum longitudinal stiffened shell. Sub-element tests were conducted on representative segments of the compression surface at maximum stress and also on segments of the load transfer joint. A 10 foot long, 77 inch diameter shell was fabricated from the design and delivered for further testing.

Henshaw, J.↗

NASA NTRS1982

Air jet levitation furnace system for observing glass microspheres during heating and melting

A collimated hole structure air jet levitation system has been developed which can be used to levitate hollow glass microspheres used in inertial confinement fusion studies. An ellipsoidal furnace has been added to the system to provide a heating source. A video camera and a 16 mm movie camera connected to a microsphere system provide real time observation as well as permanent documentation of the experiments. Microspheres have been levitated at temperatures over 1400 C for over 10 minutes at a time.

Ethridge, E. C.↗

NASA NTRS1982

Development of a preprototype times wastewater recovery subsystem

A three-man wastewater recovery preprototype subsystem using a hollow fiber membrane evaporator with a thermoelectric heat pump to provide efficient potable water recovery from wastewater on extended duration space flights was designed, fabricated, and tested at one-gravity. Low power, compactness and gravity insensitive operation are featured in this vacuum distillation subsystem. The tubular hollow fiber elements provide positive liquid/gas phase control with no moving parts, and provide structural integrity, improving on previous flat sheet membrane designs. A thermoelectric heat pump provides latent energy recovery. Application and integration of these key elements solved problems inherent in all previous reclamation subsystem designs.

Roebelen, G. J., Jr.↗

DOE OSTI2024

3D modeling of deep borehole electromagnetic measurements with energized casing source for fracture mapping at the Utah Frontier Observatory for Research in Geothermal Energy

Here, we present a 3D numerical modelling analysis evaluating the deployment of a borehole electromagnetic measurement tool to detect and image a stimulated zone at the Utah Frontier Observatory for Research in Geothermal Energy geothermal site. As the depth to the geothermal reservoir is several kilometres and the size of the stimulated zone is limited to several 100 m, surface-based controlled-source electromagnetic measurements lack the sensitivity for detecting changes in electrical resistivity caused by the stimulation. To overcome the limitation, the study evaluates the feasibility of using a three-component borehole magnetic receiver system at the Frontier Observatory for Research in Geothermal Energy site. To provide sufficient currents inside and around the enhanced geothermal reservoir, we use an injection well as an energized casing source. To efficiently simulate energizing the injection well in a realistic 3D resistivity model, we introduce a novel modelling workflow that leverages the strengths of both 3D cylindrical-mesh-based electromagnetic modelling code and 3D tetrahedral-mesh-based electromagnetic modelling code. The former is particularly well-suited for modelling hollow cylindrical objects like casings, whereas the latter excels at representing more complex 3D geological structures. In this workflow, our initial step involves computing current densities along a vertical steel-cased well using a 3D cylindrical electromagnetic modelling code. Subsequently, we distribute a series of equivalent current sources along the well's trajectory within a complex 3D resistivity model. We then discretize this model using a tetrahedral mesh and simulate the borehole electromagnetic responses excited by the casing source using a 3D finite-element electromagnetic code. This multi-step approach enables us to simulate 3D casing source electromagnetic responses within a complex 3D resistivity model, without the need for explicit discretization of the well using an excessive number of fine cells. We discuss the applicability and limitations of this proposed workflow within an electromagnetic modelling scenario where an energized well is deviated, such as at the Frontier Observatory for Research in Geothermal Energy site. Using the workflow, we demonstrate that the combined use of the energized casing source and the borehole electromagnetic receiver system offer measurable magnetic field amplitudes and sensitivity to the deep localized stimulated zone. The measurements can also distinguish between parallel-fracture anisotropic reservoirs and isotropic cases, providing valuable insights into the fracture system of the stimulated zone. Besides the magnetic field measurements, vertical electric field measurements in the open well sections are also highly sensitive to the stimulated zone and can be used as additional data for detecting and imaging the target. We can also acquire additional multiple-source data by grounding the surface electrode at various locations and repeating borehole electromagnetic measurements. This approach can increase the number of monitoring data by several factors, providing a more comprehensive dataset for analysing the deep-localized stimulated zone. The numerical analysis indicates that it is feasible to use the combination of the energized casing and downhole electromagnetic measurements in monitoring localized stimulated zone at large depths.

58 GEOSCIENCES↗

NASA NTRS1995

Design considerations for an archimedean slot spiral antenna

The design goal is to develop a 118-157 MHz, vertically polarized, low-profile (or conformal) antenna as a replacement for VHF AM blade antennas on aircraft. This design is to be arrived at by scaling the dimensions of an antenna designed for a center frequency of 1.1 GHz. The design prior to scaling may have the following maximum dimensions: diameter less than 3.70 in. and thickness less than 0.50 in. Although a four-arm spiral design was originally suggested, a two-arm spiral may also be used, as both mode-1 and mode-2 (sum and difference) radiation patterns aren't required. While a four-arm spiral can easily be designed should both sum and difference patterns be required, the two-arm design will provide the required sum pattern and simplify the design problem somewhat: only one feed is required, and the feed area geometry is more straightforward. Polarization requirements dictate that a slot spiral be used, as opposed to a wire spiral. Two similar radiating structures were considered. The first is the standard archimedean spiral antenna. The second is a hollow archimedean spiral antenna, essentially a standard archimedean spiral with the inner portion removed.

Nurnberger, Michael W.↗

NASA NTRS2005

Lightweight Radiator System for a Spacecraft

Three documents describe various aspects of a proposed lightweight, deployable radiator system for dissipating excess heat from the life-support system of a habitable spacecraft. The first document focuses on a radiator tube that would include a thin metal liner surrounded and supported by a thicker carbon-fiber-reinforced composite tubular structure that, in turn, would be formed as part of a unitary composite radiator-fin structure consisting mostly of a sheet of reticulated vitreous carbon laminated between carbon-fiber-reinforced face sheets. The thermal and mechanical properties, including the anisotropies, of the component materials are taken into account in the design. The second document describes thermo-structural bumpers, in the form of exterior multiple-ply carbon-fiber sheets enclosing hollows on opposite sides of a radiator fin, which would protect the radiator tube against impinging micrometeors and orbital debris. The third document describes a radiator system that would include multiple panels containing the aforementioned components, among others. The system would also include mechanisms for deploying the panels from compact stowage. Deployment would not involve breaking and remaking of fluid connections to the radiator panels.

Copeland, Robert J.↗

DOE OSTI2025

Tuning optical properties and local lone-pair off-centering in “hollow” FA 1− x { en } x Pb η−y Sn y Br 3 perovskites

Hollow metal halide perovskites, while a relatively recent discovery, have already been shown to push the boundaries of tuneability within an inherently limited compositional space. Here, we further expand our knowledge of these complex materials demonstrating the ability to control optical properties and local structure, notably lone-pair induced off-centering. We focus on the mixed metal FA 1−x en x Pb η−y Sn y Br 3 hollow perovskites. These compounds have wide ranging optical gaps from 1.9 eV (deep red) to 2.6 eV (light yellow), combining the anomalous bandgap red-shifting of Pb/Sn mixing with the blue-shifting effects of the organic substitution. Average and local structural studies employing single crystal X-ray diffraction and total X-ray scattering pair distribution function analyses respectively suggest strong incoherent off-centering distortions that are locally correlated with Sn concentration. The inclusion of ethylenediammonium dications appears to regulate metal off-centering, opening new opportunities of research into this phenomenon.

Balvanz, Adam [Northwestern University, Evanston, ↗