Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Conductor-backed coplanar waveguide resonators of YBa2Cu3O(7-delta) on LaAlO3

Conductor-backed coplanar waveguide (CBCPW) resonators operating at 10.8 GHz have been fabricated from laser ablated and off-axis magnetron sputtered YBa2Cu3O(7-delta) (YBCO) high-temperature superconducting (HTS) thin films on LaAlO3. These resonators were tested in the temperature range from 14 to 92 K. The unloaded quality factor at 77 K of the HTS CBCPW resonators was 3 to 4 times that of a similar gold resonator. To the authors' knowledge, these results represent the first reported measurements of HTS-based CBCPW resonators.

Miranda, Felix A.↗
NASA NTRS1990

Space applications for high temperature superconductivity - Brief review

An overview is presented of materials and devices based on high-temperature superconductivity (HTS) that could have useful space-oriented applications. Of specific interest are applications of HTS technologies to mm and microwave systems, spaceborne and planet-surface sensors, and to magnetic subsystems for robotic, rescue, and docking maneuvers. HTS technologies can be used in optoelectronics, magnetic-field detectors, antennae, transmission/delay lines, and launch/payload coils.

Krishen, Kumar↗
NASA NTRS1993

Superconducting microstrip antennas - An experimental comparison of two feeding methods

The recent discovery of high-temperature superconductors (HTSs) has generated a substantial amount of interest in microstrip antenna applications. However, the high permittivity of substrates compatible with HTS causes difficulty in feeding such antennas because of the high patch edge impedance. Two methods for feeding HTS microstrip antennas at K- and Ka-band are examined. Superconducting microstrip antennas that are directly coupled and gap-coupled to a microstrip transmission line have been designed and fabricated on lanthanum aluminate substrates using Y-Ba-Cu-O superconducting thin films. Measurements from these antennas, including input impedance, bandwidth, efficiency, and patterns, are presented and compared with published models. The measured results demonstrate that usable antennas can be constructed using either of these architectures, although the antennas suffer from narrow bandwidths. In each case, the HTS antenna shows a substantial improvement over an identical antenna made with normal metals.

Richard, M. A.↗
NASA NTRS1994

Experimental design for the evaluation of high-T(sub c) superconductive thermal bridges in a sensor satellite

Infrared sensor satellites, which consist of cryogenic infrared sensor detectors, electrical instrumentation, and data acquisition systems, are used to monitor the conditions of the earth's upper atmosphere in order to evaluate its present and future changes. Currently, the electrical connections (instrumentation), which act as thermal bridges between the cryogenic infrared sensor and the significantly warmer data acquisition unit of the sensor satellite system, constitute a significant portion of the heat load on the cryogen. As a part of extending the mission life of the sensor satellite system, the researchers at the National Aeronautics and Space Administration's Langley Research Center (NASA-LaRC) are evaluating the effectiveness of replacing the currently used manganin wires with high-temperature superconductive (HTS) materials as the electrical connections (thermal bridges). In conjunction with the study being conducted at NASA-LaRC, the proposed research is to design a space experiment to determine the thermal savings on a cryogenic subsystem when manganin leads are replaced by HTS leads printed onto a substrate with a low thermal conductivity, and to determine the thermal conductivities of HTS materials. The experiment is designed to compare manganin wires with two different types of superconductors on substrates by determining the heat loss by the thermal bridges and providing temperature measurements for the estimation of thermal conductivity. A conductive mathematical model has been developed and used as a key tool in the design process and subsequent analysis.

Scott, Elaine P.↗
NASA NTRS1995

Space qualified hybrid superconductor/semiconductor planar oscillator circuit

We report on the space qualification of a hybrid superconductor/semiconductor planar local oscillator (LO) at 8.4 GHz. This oscillator was designed, fabricated, and tested as a component for the High Temperature Superconductivity Space Experiment 2 (HTSSE-2). The LO consisted of a GaAs MESFET and microstrip circuitry patterned onto a YBa2Cu3O(7-delta) high temperature superconducting (HTS) thin film on a 1.0 x 1.0 sq cm lanthanum aluminate (LaAlO3) substrate. At 77 K, this oscillator achieved power output levels up to 10 dBm into a 50 Ohm load. When incorporated into a full cryogenic receiver, the LO provided output powers within 0.0-3.0 dBm with less than 50 mW of dc power dissipation. Space qualification data on the sensitivity of the HTS films to the processing steps involved in the fabrication of HTS-based components are presented. Data on ohmic contacts, strength of wire bonds made to such contacts, and aging effects as well as vibration test results are discussed.

Miranda, F. A.↗
NASA NTRS1995

Integrated Cryogenic Satellite Communications Cross-Link Receiver Experiment

An experiment has been devised which will validate, in space, a miniature, high-performance receiver. The receiver blends three complementary technologies; high temperature superconductivity (HTS), pseudomorphic high electron mobility transistor (PHEMT) monolithic microwave integrated circuits (MMIC), and a miniature pulse tube cryogenic cooler. Specifically, an HTS band pass filter, InP MMIC low noise amplifier, HTS-sapphire resonator stabilized local oscillator (LO), and a miniature pulse tube cooler will be integrated into a complete 20 GHz receiver downconverter. This cooled downconverter will be interfaced with customized signal processing electronics and integrated onto the space shuttle's 'HitchHiker' carrier. A pseudorandom data sequence will be transmitted to the receiver, which is in low Earth orbit (LEO), via the Advanced Communication Technology Satellite (ACTS) on a 20 GHz carrier. The modulation format is QPSK and the data rate is 2.048 Mbps. The bit error rate (BER) will be measured in situ. The receiver is also equipped with a radiometer mode so that experiment success is not totally contingent upon the BER measurement. In this mode, the receiver uses the Earth and deep space as a hot and cold calibration source, respectively. The experiment closely simulates an actual cross-link scenario. Since the receiver performance depends on channel conditions, its true characteristics would be masked in a terrestrial measurement by atmospheric absorption and background radiation. Furthermore, the receiver's performance depends on its physical temperature, which is a sensitive function of platform environment, thermal design, and cryocooler performance. This empirical data is important for building confidence in the technology.

Romanofsky, R. R.↗
NASA NTRS1996

High Temperature Superconducting Magnets with Active Control for Attraction Levitation Transport Applications

A research program, involving 3 British universities, directed at quantifying the controllability of High Temperature Superconducting (HTS) magnets for use in attraction levitation transport systems will be described. The work includes measurement of loss mechanisms for iron cored HTS magnets which need to produce a flux density of approx. 1 tesla in the airgap between the magnet poles and a ferromagnetic rail. This flux density needs to be maintained and this is done by introducing small variations of the magnet current using a feedback loop, at frequencies up to 10 Hz to compensate for load changes, track variation etc. The test magnet assemblies constructed so far will be described and the studies and modelling of designs for a practical levitation demonstrator (using commercially obtained HTS tape) will be discussed with particular emphasis on how the field distribution and its components, e.g., the component vector normal to the broad face of the tape, can radically affect design philosophy compared to the classical electrical engineering approach. Although specifically aimed at levitation transport the controllability data obtained have implications for a much wider range of applications.

Jones, Harry↗
NASA NTRS1996

Development of Y-Ba-Cu-O Superconductors for Magnetic Bearings

The material requirements, material manufacturing and magnetic properties that are relevant to fabrication of High Temperature Superconductor (HTS) magnetic bearings have been discussed. It is found that the seeded-melt-texturing method can be used to fabricate the single domain material that is required to achieve the best magnetic properties. Trapped-field mapping has been used as a non-destructive tool to determine the single-domain nature of the HTS material and quantity of the HTS disks. Both the trapped field and the levitation force of the Y-Ba-Cu-O disks are found to be strongly sensitive to the oxygen content.

Selvamanickam, V.↗
NASA NTRS2004

Advanced Adiabatic Demagnetization Refrigerators for Continuous Cooling

The research at Houston was focused on optimizing the design of superconducting magnets for advanced adiabatic demagnetization refrigerators (ADRs), assessing the feasibility of using high temperature superconducting (HTS) magnets in ADRs in the future, and developing techniques to deposit HTS thin and thick films on high strength, low thermal conductivity substrates for HTS magnet leads. Several approaches have been tested for the suggested superconducting magnets.

Chu, Paul C. W.↗
NASA NTRS1993

Superconducting Microstrip Antennas: An Experimental Comparison of Two Feeding Methods

The recent discovery of high-temperature superconductors (HTSs) has generated a substantial amount of interest in microstrip antenna applications. However, the high permittivity of substrates compatible with HTS causes difficulty in feeding such antennas because of the high patch edge impedance. Two methods for feeding HTS microstrip antennas at K- and Ka-band are examined. Superconducting microstrip antennas that are directly coupled and gas-coupled to a microstrip transmission line have been designed and fabricated on lanthanum aluminate substrates using Y-Ba-Cu-O superconducting thin films. Measurements from these antennas, including input impedance, bandwidth, efficiency, and patterns, are presented and compared with published models. The measured results demonstrate that usable antennas can be constructed using either of these architectures, although the antennas suffer from narrow bandwidths. In each case, the HTS antenna shows a substantial improvement over an identical antenna made with normal metals

Richard, Mark A.↗
NASA NTRS2019

Magnet Architectures and Active Radiation Shielding Study (MAARSS)

This report describes the analysis of several magnetic radiation shield architectures and the spacecraft systems associated with them, such as quench detection, thermal management, and compensation coils. This work was performed as part of the NASA Institute of Advanced Concepts (NIAC) Grant Phase II effort. Because radiation exposure during long duration space missions poses a significant risk for crewed space-flight, Advanced Magnetic Lab, Inc. (AML) and NASA are studying magnetic radiation shielding, which may generate low-mass protection. Recent technological developments in high-temperature superconducting technology suggest the possibility of such shielding. This report analyzes some of the technical difficulties involved in such a system and identifies technology areas where further investment would be warranted. Most analysis was performed on a baseline configuration (8-meter diameter coils, with 1 tesla field). However, a baseline design with an expandable coil configuration (16 meter diameter coils, 1.5 tesla field) has a significant potential to increase shielding efficiency. The magnetic forces on the magnetic shield's components are large enough to require detailed structural design. Analysis of the thermal structural response of a yttrium-barium-copper-oxide (YBCO) high-temperature, superconducting (HTS) tape in a large-scale solenoid magnet showed that structural and thermal performance improved by replacing Hastelloy® with graphene in the tape. Integrating graphene into the high-strength fiber (HSF) support structure brings even greater benefits. The energy stored in a shield system's magnetic field must be safely dissipated if a quench-type failure occurs. Analysis of quench detection by fiber-optic thermal sensing and improvement of quench characteristics using graphene showed quench is manageable. Low-temperature superconductors can quench when subjected to movement, but lab tests of coil expansion testing showed that HTS materials do not quench when subject to the movement associated with coil expansion. Compensation coils are necessary to reduce the magnetic field in the crew habitat. Analysis showed that subdividing the compensation coil into individually controlled sections allows for a robust, adjustable system. AML analyzed the forces on an approaching capsule that were a result of eddy currents in its structure induced by its motion through the magnetic field from the coils. AML also analyzed coil-to-coil forces. Thermal control to maintain the HTS material at a suitable temperature is challenging. The sunshield technology review revealed a greater possibility of thermal insulation of the coils and use of passive cooling. The availability of suitable cryocoolers was also reviewed. A parametric graph estimating mass and shielding effectiveness for strength and thickness was developed, and allows spacecraft designers to assess the tradeoffs of using a magnetic radiation shield.

Spacecraft↗
NASA NTRSDate not supplied

Overview and Performance Characterization of Northrop Grumman’s 1 kW Hall Thruster String

Northrop Grumman (NG) Tactical Space SystemsDivisionhas embarked on the development and qualification of a high throughput, low power Hall Thruster String (HTS) using hardware designed and built in-house.Following the success of Mission Extension Vehicles 1 and 2, NG is currently developing the next generation in its lineupof satellite servicing capabilities, the Mission Robotics Vehicle(MRV)and Mission Extension Pod (MEP).MEP’s mission profile imposes highly demanding requirements upon the electric propulsion system. When surveying the industry for available systems, NGwas unable to identify any mature Hall thrustersystems that could satisfy the performance and lifetime requirements for MEP. Eventually, it was decided to vertically integrate the EP development process, partneringwith NASA Glenn Research Center to leverage ongoing development at GRC of a high throughput, low power Hall thruster. The components of the HTS have successfully passed PDR and are currently in the engineering development and test phase. Based on performancecharacterization testingof the development hardware,NG’s low power Hall thruster, dubbed the NGHT-1X, promises to deliver state-of-the-art performanceand lifetime for a sub-kW Hall thruster, achieving total efficiencies of 50-55% over a wide range of throttle conditions. Results of a seriesof characterization tests including integrated systems testingwith the PPUare presented.Qualification methodology andthruster lifetime verification is also discussed. Environmental qualification of the HTS components is expected to completein mid-2023 with a first flight in mid-2024.

Propulsion↗
NASA NTRS2023

Passively Cooled Superconductors Final Report

A highly reflective spray-on coating and tile material has been under development at Kennedy Space Center (KSC) that scatters away most of the Sun’s energy, thereby allowing coated objects to remain cool in space. The best performing tile material has achieved 1% solar absorptivity while the best performing spray-on coating has achieved around 4%. Both versions passively maintain cryogenic temperatures below 120 K at 1 astronomical unit (AU) from the Sun, but the tile material consistently sustains temperatures below 90 K, which is low enough to preserve oxygen and methane in a liquid state. Besides keeping propellants cold, this “solar white” material has the potential to passively maintain high-temperature superconductors (HTS) in a superconducting state without the support of liquid nitrogen cooling. If superconductors can be operated without the added infrastructure of liquid nitrogen cooling, it may enable them to be used in space for applications like magnetic radiation shielding and efficient energy management. Long duration exposure to both galactic cosmic radiation and coronal mass ejections can pose health risks for the astronauts and increase the potential for damage to electronics. This makes shielding essential to accomplish long duration missions, particularly when astronauts are onboard. The objective of this project was to determine the extent we could keep a high-temperature superconducting (HTS) material passively chilled to maintain its superconducting state. Both the tile and spray-on versions of solar white were investigated. We focused on finding a version that could support passive cooling at 1 AU from the Sun and determined the closest operating distances for samples that were unable to perform at 1 AU. Early in the project, we selected bismuth strontium calcium copper oxide (BSCCO) as the HTS to test based on its reputable usage in superconducting wires. The version we selected was Bi-2223, which has a critical temperature of about 108 K. Sample bars with contacts for a four-point probe were obtained from Quantum Levitation: https://quantumlevitation.com/product/superconductor-bar-for-4-point-tc-experiment/.

superconductors↗
DOE OSTI2025

Analysis of Screening Current Effects in a Hybrid Nb$_{3}$Sn/REBCO Superconducting Accelerator Magnet Using a T - A Formulation

To explore the feasibility of using high-temperature superconducting (HTS) REBCO coated conductors in future accelerator magnets, two REBCO flat racetrack coils were fabricated using 4-mm wide EuBCO tapes at the High Energy Accelerator Research Organization (KEK). These coils were tested as an insert inside a Nb$_{3}$Sn common-coil dipole magnet, which provides a background field of up to $\sim$ 9.5T, at the Brookhaven National Laboratory (BNL). REBCO tapes offer exceptionally high critical current density under strong magnetic fields; however, they also exhibit significant magnetization due to screening currents, leading to magnetic field errors. Here, this study presents a 2D finite element model of screening current-induced fields (SCIF) in REBCO coils using the T-A formulation, along with the results obtained. Simulations were then performed for two KEK test cases: one where the REBCO conductors were oriented with the HTS tapes parallel to the background field, and another where the tapes were perpendicular to it. Since screening currents also influence the stress distribution and increase the peak stress in the coils, the mechanical effects of these currents were analyzed. The implications of these simulation and test results for the design of Nb$_{3}$Sn/REBCO superconducting accelerator magnets are discussed.

Accelerator magnets↗
DOE OSTI2025

Enhancing HT-WGS catalyst performance with stable monovalent copper species via electron supply from defect-induced MgO

Magnesium oxide (MgO) exhibits excellent synergy with cerium oxide (CeO2), serving as either textural or electronic promoters during catalytic reactions. However, achieving well-dispersed CeO2-MgO is technically challenging because they are known not to form solid solutions, and the crystal growth of CeO2 suppresses the structure formation of MgO, leading to MgO being in an inhomogeneous amorphous state within CeO2-MgO. For this reason, most of research groups have been struggling with synthesizing well-dispersed CeO2-MgO. This leads them to focusing on the interaction between the active metal and cerium, overlooking the true role of magnesium. In this study, we successfully synthesized well-dispersed CeO2-MgO via a spray pyrolysis-assisted evaporation-induced self-assembly method, followed by the impregnation of Cu. The location and dispersion of Cu nanoparticles were highly dependent on the MgO distribution. Additionally, we revealed that this significantly influenced the catalytic activity and stability towards the HTS reaction and furthermore supplies electrons to monovalent Cu species, helping maintain the stable electron structure and oxidation state of Cu species considered as active sites. These findings suggest that optimizing the MgO distribution in CeO2-MgO is a promising strategy for developing efficient catalysts for the HTS reaction, emphasizing the role of MgO in designing high-performance catalysts.

Kim, Min-Jae↗
DOE OSTI2025

Magnetic and Mechanical Analysis of Bi-2212 Rutherford Cable in a Cos-Theta Sub-Scale Dipole Coil

The U.S. Magnet Development Program (US-MDP) explores high-field accelerator magnets compatible with operational conditions beyond the limits of Nb$_3$Sn technology. The ongoing R&D High-Temperature Superconductors (HTS) suggests using Bi$_2$Sr$_2$CaCu$_2$O$_{8-x}$ (Bi-2212) as superconducting element. Bi-2212 Rutherford cables maintain a high critical current (I$_C$) when exposed to a large external magnetic field. However, Bi-2212 exhibits an oversensitive stress-strain response when subject to large Lorentz forces. This paper reports on the magnetic and mechanical analysis of the Bi-2212 cosine-theta insert being developed at Fermilab for a hybrid magnet composed of two external layers of Nb$_3$Sn and two internal layers of Bi-2212. We performed a FEM analysis of the insert to estimate the HTS stress state in the coil's strands under magnetic and mechanical loads.

43 PARTICLE ACCELERATORS↗
DOE OSTI2026

Mechanical characterization of Bi-2212 composite winding pack samples for high-field superconducting magnet design

Bi₂Sr₂CaCu₂O8−x (Bi-2212) multi-filament round wire is a high-temperature superconductor (HTS) capable of carrying high transport currents, which makes it suitable for high-field magnet applications. However, its weak Ag–Mg sheath leaves it vulnerable to mechanical stress, posing challenges for high-field magnet design. To better understand and improve mechanical stress management in Bi-2212 winding packs, we conducted an experimental study evaluating the axial stress–strain behavior of five winding pack configurations with varying insulation materials, reinforcement strategies, and construction quality. Using uniaxial tensile testing at 77 K, we measured Young’s modulus and Poisson’s ratio for each composition. Our results show that pure alumina braid insulation and co-wind reinforcements significantly enhance stiffness compared to aluminosilicate braids, with more than 2.5 times increased winding pack Young’s modulus. Rule of mixtures analysis further quantified the contribution of non-wire composite components to overall stiffness. These findings highlight the critical role of insulation material selection and reinforcement design in optimizing Bi-2212 coil performance under stress, providing a foundation for improved mechanical models and more reliable high-field HTS magnet designs.

Bi-2212 magnet↗
DOE OSTI2026

(Ir)Relevance of Disorder for Superconductivity in Cuprates

In cuprates that exhibit high-temperature superconductivity (HTS), as the doping level 𝑝 is increased beyond the optimal value, the superfluid density 𝑛 𝑠⁢0 decreases and eventually vanishes, closely tracking the critical temperature 𝑇 𝑐 . This has been interpreted using a dirty-𝑑-wave extension of the Bardeen-Cooper-Schrieffer theory, assuming that 𝑇 𝑐 and 𝑛 𝑠⁢0 decrease with increasing disorder and pair breaking. Here, to test this hypothesis, we tuned the doping level in overdoped La 2-x ⁢Sr x ⁢CuO 4−𝛿 films by electrolyte gating, measured several parameters used to quantify the level of disorder (the residual resistivity ratio RRR, the mean free path 𝑙 0 , and the electron mobility 𝜇), and studied how 𝑇 𝑐 and 𝑛 𝑠⁢0 scale with these. The experimentally measured dependence turned out to be the opposite of the expected—𝑇 𝑐 and 𝑛 𝑠⁢0 increased with increasing disorder. This brings the question of the true origin of the demise of 𝑇 𝑐 and 𝑛 𝑠⁢0 with overdoping back to the center stage of the quest to decipher the HTS enigma.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗