Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Gas Receiver”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Ground test program for a full-size solar dynamic heat receiver

Test hardware, facilities, and procedures were developed to conduct ground testing of a full-size, solar dynamic heat receiver in a partially simulated, low earth orbit environment. The heat receiver was designed to supply 102 kW of thermal energy to a helium and xenon gas mixture continuously over a 94 minute orbit, including up to 36 minutes of eclipse. The purpose of the test program was to quantify the receiver thermodynamic performance, its operating temperatures, and thermal response to changes in environmental and power module interface boundary conditions. The heat receiver was tested in a vacuum chamber using liquid nitrogen cold shrouds and an aperture cold plate. Special test equipment was designed to provide the required ranges in interface boundary conditions that typify those expected or required for operation as part of the solar dynamic power module on the Space Station Freedom. The support hardware includes an infrared quartz lamp heater with 30 independently controllable zones and a closed-Brayton cycle engine simulator to circulate and condition the helium-xenon gas mixture. The test article, test support hardware, facilities, and instrumentation developed to conduct the ground test program are all described.

Sedgwick, L. M.↗
NASA NTRS1993

Fluid absorption solar energy receiver

A conventional solar dynamic system transmits solar energy to the flowing fluid of a thermodynamic cycle through structures which contain the gas and thermal energy storage material. Such a heat transfer mechanism dictates that the structure operate at a higher temperature than the fluid. This investigation reports on a fluid absorption receiver where only a part of the solar energy is transmitted to the structure. The other part is absorbed directly by the fluid. By proportioning these two heat transfer paths the energy to the structure can preheat the fluid, while the energy absorbed directly by the fluid raises the fluid to its final working temperature. The surface temperatures need not exceed the output temperature of the fluid. This makes the output temperature of the gas the maximum temperature in the system. The gas can have local maximum temperatures higher than the output working temperature. However local high temperatures are quickly equilibrated, and since the gas does not emit radiation, local high temperatures do not result in a radiative heat loss. Thermal radiation, thermal conductivity, and heat exchange with the gas all help equilibrate the surface temperature.

Bair, Edward J.↗
NASA NTRS2001

Galaxy Cluster Gas Mass Fractions From Sunyaev-Zeldovich Effect Measurements: Constraints on Omega(M)

Using sensitive centimeter-wave receivers mounted on the Owens Valley Radio Observatory and Berkeley-Illinois-Maryland-Association millimeter arrays, we have obtained interferometric measurements of the Sunyaev-Zeldovich(SZ) effect toward massive galaxy clusters. We use the SZ data to determine the pressure distribution of the cluster gas and, in combination with published X-ray temperatures, to infer the gas mass and total gravitational mass of 18 clusters. The gas mass fraction, f(g), is calculated for each cluster and is extrapolated to the fiducial radius r(500) using the results of numerical simulations. The mean f(g) within r(500) is 0.081(+ 0.009 / - 0.011) per h(100) (statistical uncertainty at 68% confidence level, assuming Omega(M) = 0.3, Omega(Lambda) = 0.7). We discuss possible sources of systematic errors in the mean f(sub g) measurement. We derive an upper limit for Omega(M) from this sample under the assumption that the mass composition of clusters within r(500) reflects the universal mass composition: Omega(M)h is less than or equal to Omega(B)/f(g). The gas mass fractions depend on cosmology through the angular diameter distance and the r(500) correction factors. For a flat universe (Omega(Lambda) is identical with 1 - Omega(M)) and h = 0.7, we find the measured gas mass fractions are consistent with Omega(M) is less than 0.40, at 68% confidence. Including estimates of the baryons contained in galaxies and the baryons which failed to become bound during the cluster formation process, we find Omega(M) is approximately equal to 0.25.

Grego, Laura↗
NASA NTRS1973

Catalysis study for space shuttle vehicle thermal protection systems

Experimental results on the problem of reducing aerodynamic heating on space shuttle orbiter surfaces are presented. Data include: (1) development of a laboratory flow reactor technique for measuring gamma sub O and gamma sub N on candidate materials at surfaces, T sub w, in the nominal range 1000 to 2000, (2) measurements of gamma sub O and gamma sub N above 1000 K for both the glass coating of a reusable surface insulation material and the siliconized surface of a reinforced pyrolyzed plastic material, (3) measurement of the ablation behavior of the coated RPP material at T sub w is greater than or equal to 2150 K, (4) X-ray photoelectron spectral studies of the chemical constituents on these surfaces before and after dissociated gas exposure, (5) scanning electron micrograph examination of as-received and reacted specimens, and (6) development and exploitation of a method of predicting the aerodynamic heating consquences of these gamma sub O(T sub w) and gamma sub N(T sub w) measurements for critical locations on a radiation cooled orbiter vehicle.

Breen, J.↗
NASA NTRS2001

From the Cluster Temperature Function to the Mass Function at Low Z

The project consists of three X-ray Multimirror Mission (XMM) observations of the hot, nearby galaxy cluster Triangulum Australis (one pointing to the cluster center and two offsets). The major goal of the project is to obtain an accurate radial gas temperature profile out to large radii and derive the total gravitating mass within the radius of over density 500. A secondary goal is to obtain a detailed two-dimensional gas temperature map of the central region. We have recently received the central pointing (of the two CDROMs received, one contains the central pointing and the other, a zero-exposure dummy observation). The analysis of the data at hand is underway with the aim of deriving the two-dimensional temperature map. At present, we have to limit quantitative analysis to the EPIC-MOS data because of the absence of the necessary calibration products for the Extended Full Frame mode used for EPIC-pn in these observations. We anticipate the arrival of the data from the remaining two offset pointings in the near future, after which we will be able to undertake the total mass derivation. Money from this year's installment of the grant was partially spent on an upgrade of the computer used for the above data analysis, and on travel to a conference that extensively discussed the XMM calibration issues.

Markevitch, Maxim↗
NASA NTRS2017

Cavity Pull Rod: Device to Promote Single Crystal Growth from the Melt

A pull rod for use in producing a single crystal from a molten alloy is provided that includes an elongated rod having a first end and a second end, a first cavity defined at the first end and a second cavity defined at the first end and in communication with the first cavity. The first cavity receives the molten alloy and the second cavity vents a gas from the molten alloy to thereby template a single crystal when the pull rod is dipped into and extracted from the molten alloy.

Goldsby, Jon↗
NASA NTRS2001

Galaxy Cluster Gas Mass Fractions From Sunyaev-Zel'dovich Effect Measurement: Constraints on Omega_M

Using sensitive centimeter-wave receivers mounted on the Owens Valley Radio Observatory and Berkeley-Illinois-Maryland-Association millimeter arrays, we have obtained interferometric measurements of the Sunyaev-Zei'dovich (SZ) effect toward massive galaxy clusters. We use the SZ data to determine the pressure distribution of the cluster gas and, in combination with published X-ray temperatures, to infer the gas mass and total gravitational mass of 18 clusters. The gas mass fraction, f~g, is calculated for each cluster, and is extrapolated to the fiducial radius r_{500} using the results of numerical simulations. The mean f_g within r_{500} is 0.081 + 0.009 - 0.011/(h_{100} (statistical uncertainty at 68% confidence level, assuming OmegaM=0.3, OmegaL=0.7). We discuss possible sources of systematic errors in the mean f 9 measurement. We derive an upper limit for OmegaM from this sample under the assumption that the mass composition of clusters within r_{500} reflects the universal mass composition: Omega_M h <Omega_B/f_g.The gas mass f on cosmology through the angular diameter distance and the r_{500} correction factors. For a flat universe (Omegal, = 1 - OmegaM) and h=0.7, we find the measured gas mass fractions are consistent with OmegaM less than 0.40, at 68% confidence. Including estimates of the baryons contained in galaxies and the baryons which failed to become bound during the cluster formation process, we find OmegaM\approximately 0.25.

Grego, Laura↗
NASA NTRS2015

A Miniaturized Laser Heterodyne Radiometer for Greenhouse Gas Measurements in the Atmospheric Column

Laser Heterodyne Radiometry is a technique adapted from radio receiver technology has been used to measure trace gases in the atmosphere since the 1960s.By leveraging advances in the telecommunications industry, it has been possible to miniaturize this technology.The mini-LHR (Miniaturized Laser Heterodyne Radiometer) has been under development at NASA Goddard Space flight Center since 2009. This sun-viewing instrument measures carbon dioxide and methane in the atmospheric column and operates in tandem with an AERONET sun photometer producing a simultaneous measure of aerosols. The mini-LHR has been extensively field tested in a range of locations ranging in the continental US as well as Alaska and Hawaii and now operates autonomously with sensitivities of approximately 0.2 ppmv and approximately10 ppbv, for carbon dioxide and methane respectively, for 10 averaged scans under clear sky conditions.

CO2↗
NASA NTRS1982

Cold-air performance of compressor-drive turbine of Department of Energy upgraded automobile gas turbine engine. 2: Stage performance

The aerodynamic performance of the compressor-drive turbine of the DOE upgraded gas turbine engine was determined in low temperature air. The as-received cast rotor blading had a significantly thicker profile than design and a fairly rough surface finish. Because of these blading imperfections a series of stage tests with modified rotors were made. These included the as-cast rotor, a reduced-roughness rotor, and a rotor with blades thinned to near design. Significant performance changes were measured. Tests were also made to determine the effect of Reynolds number on the turbine performance. Comparisons are made between this turbine and the compressor-drive turbine of the DOE baseline gas turbine engine.

Roelke, R. J.↗
NASA NTRS1992

Redistribution of Ti and Al in deuterium charged TiAl

The redistribution of titanium and aluminum in a single-phase TiAl alloy that has been exposed to a high pressure of deuterium gas at high temperature is studied. The microstructure in the as-received, uncharged condition consisted of single-phase gamma TiAl grains and a random distribution of precipitates. Precipitates were distributed throughout the matrix and along the grain boundaries. The chemistry of the precipitates varied considerably; some were rich in Al, while other were mostly Ti with some Si and Al. The dislocation density in most grains was low, although in a few grains a high dislocation density was observed. FCC deuterides with a lattice parameter of 0.45 nm form in a Ti-52.1Al-2.1Ta (at. pct) alloy after exposure to 1.38 MPa of deuterium gas at 650 C for 213 hr. The structure and lattice parameter are consistent with the formation of Ti(l)D2. The deuterides that form in this alloy are enriched in Ti and deficient in Al and Ta compared to the deuteride-free matrix. Regions of the matrix contiguous with the deuterides have a correspondingly enhanced aluminum and tantalum concentration.

Legzdina, D.↗
NASA NTRS1992

A new Lagrangian method for real gases at supersonic speed

With the renewed interest in high speed flights, the real gas effect is of theoretical as well as practical importance. In the past decade, upwind splittings or Godunov-type Riemann solutions have received tremendous attention and as a result significant progress has been made both in the ideal and non-ideal gas. In this paper, we propose a new approach that is formulated using the Lagrangian description, for the calculation of supersonic/hypersonic real gas inviscid flows. This new formulation avoids the grid generation step which is automatically obtained as the solution procedure marches in the 'time-like' direction. As a result, no remapping is required and the accuracy is faithfully maintained in the Lagrangian level. In this paper, we give numerical results for a variety of real gas problems consisting of essential elements in high speed flows, such as shock waves, expansion waves, slip surfaces and their interactions. Finally, calculations for flows in a generic inlet and nozzle are presented.

Loh, C. Y.↗
NASA NTRS2014

Herschel Extreme Lensing Line Observations: Dynamics of Two Strongly Lensed Star-Forming Galaxies near Redshift z=2*

We report on two regularly rotating galaxies at redshift z approx. = 2, using high-resolution spectra of the bright [C microns] 158 micrometers emission line from the HIFI instrument on the Herschel Space Observatory. Both SDSS090122.37+181432.3 ("S0901") and SDSSJ120602.09+514229.5 ("the Clone") are strongly lensed and show the double-horned line profile that is typical of rotating gas disks. Using a parametric disk model to fit the emission line profiles, we find that S0901 has a rotation speed of v sin(i) approx. = 120 +/- 7 kms(sup −1) and a gas velocity dispersion of (standard deviation)g < 23 km s(sup −1) (1(standard deviation)). The best-fitting model for the Clone is a rotationally supported disk having v sin(i) approx. = 79 +/- 11 km s(sup −1) and (standard deviation)g 4 kms(sup −1) (1(standard deviation)). However, the Clone is also consistent with a family of dispersion-dominated models having (standard deviation)g = 92 +/- 20 km s(sup −1). Our results showcase the potential of the [C microns] line as a kinematic probe of high-redshift galaxy dynamics: [C microns] is bright, accessible to heterodyne receivers with exquisite velocity resolution, and traces dense star-forming interstellar gas. Future [C microns] line observations with ALMA would offer the further advantage of spatial resolution, allowing a clearer separation between rotation and velocity dispersion.

LENSING↗
NASA NTRS1973

Development of isothermal rigs

The results of the Resonant Infrasonic Gauging System (RIGS) development program are reported. The RIGS is a gauging system that is capable of measuring propellant quantity under zero-G as well as under accelerated (one-G) conditions. With the exception of liquid hydrogen, it can be used to gauge virtually any propellant in liquid form including cryogenics. The gauge consists of a sensor unit which is attached to the propellant tank and electronic control unit which may be positioned separately from the sensor. The control unit receives the signals from the sensor as well as the ullage gas pressure and propellant temperature measurements, and computes the propellant quantity remaining in the tank. During the course of this program two prototype RIGS sensors were designed and constructed. The sensors were tested first in the laboratory using water as the simulated propellant and, later, using LN2 in a 100-gallon tank. The system tests proved that the gauge operates virtually as predicted by theory and yielded an accuracy better than 1%.

Kaminskas, R. A.↗
NASA NTRS1978

Substitution of ceramics for high temperature alloys

Ceramics such as silicon nitride and silicon carbide are currently receiving a great deal of attention as potential materials for advanced gas turbine engines. The primary advantage offered by ceramics is their high temperature capability which can result in turbine engines of improved efficiency. Other advantages when compared to the nickel and cobalt alloys in current use are raw material availability, lower weight, erosion/corrosion resistance, and potentially lower cost. The use of ceramics in three different sizes of gas turbine engines is considered; these are the large utility turbines, advanced aircraft turbines, and small automotive turbines. The effects of material substitutions are reviewed in terms of engine performance, operating economy, and secondary effects.

Probst, H. B.↗
NASA NTRS1981

Laser absorption spectrometer - Remote measurement of tropospheric ozone

The laser absorption spectrometer (LAS) is an airborne instrument able to perform remote measurement of trace atmospheric gases. The instrument uses a pair of carbon dioxide laser-heterodyne receiver systems that are directed downward from an airplane and determines gas concentration by the differential absorption method. Configured to measure tropospheric ozone, the LAS has been used in conjunction with another instrumented aircraft to test the accuracy of this method of measurement. A complete description of the instrument is presented, and the results of extensive flight testing are summarized.

Shumate, M. S.↗
NASA NTRS1998

Obtaining the Mass and Radius of Extra-Solar Giant Planets

The scientific utility and feasibility of detecting transits of the 9 known extrasolar planets is explored. A transit of a solar-like star by a Jupiter mass planet produces a 1% decrease in the amount of light received from the star. Transit observation will remove the ambiguity in the measurement of the planetary mass inherent in the radial velocity method and confirm the planet's existence. The 9 known planets have a 33% chance of producing at least one observable transit. Additional extrasolar planet detections from the radial velocity surveys will increase this probability to greater than 90%. The radius of the planet can be determined by the fractional decrease in light received during transit. The mass and radius may distinguish rocky or gas giant planets from brown dwarfs. The probability of detection, the transit signal size and duration, and predictions of the transit times (including errors) are calculated for circular and elliptical orbits. Observational limits are investigated and it is shown that small telescopes and existing detectors are adequate enough to achieve the 0.1% photometry necessary to detect transits of the known extrasolar planets.

Castellano, Tim↗
NASA NTRS2009

Study of Electro-Cyclonic Filtration and Pneumatic Transfer of Lunar Regolith Simulants under 1/6-g and 1-g Gravity Conditions

NASA has built a prototype oxygen production plant to process the lunar regolith using the hydrogen reduction chemical process. This plant is known as "ROxygen - making oxygen from moon rocks". The ROxygen regolith transfer team has identified the flow and transfer characteristics of lunar regolith simulant to be a concern for lunar oxygen production efforts. It is important to ISRU lunar exploration efforts to develop hardware designs that can demonstrate the ability to flow and transfer a given mass of regolith simulant to a desired vertical height under lunar gravity conditions in order to introduce it into a reactor. We will present results obtained under both 1/6-g and 1-g gravity conditions for a system that can pneumatically convey 16.5 kg of lunar regolith simulant (NU-LHT-2M, Mauna Kea Tephra, and JSC-1A) from a flat-bottom supply hopper to a simulated ISRU reactor (dual-chambered receiving hopper) where the granular material is separated from the convey gas (air) using a series of cyclone separators, one of which is an electrically enhanced cyclone separator (electrocyclone). The results of our study include (1) the mass flow rate as a function of input air pressure for lunar regolith simulants that are conveyed pneumatically as a dusty gas in a vertical direction against gravity under lunar gravity conditions (for NU-LHT-2M and Mauna Kea Tephra), and under earth gravity conditions (for NU-LHT-2M, Mauna Kea Tephra and JSC-1A), and (2) the efficiency of the cyclone/electrocyclone filtration system in separating the convey gas (air) from the granular particulates as a function of particle size.

Mantovani, James G.↗
NASA NTRS1993

Extended CO(7-6) emission from warm gas in Orion

Results of a search for extended CO(7-6) line emission in the Orion A molecular cloud using the University of Texas submillimeter laser heterodyne receiver are presented. The large-scale distribution of quiescent CO(7-6) emission is mapped along a cut across the Trapezium cluster extending more than 13 arcmin (nearly 2 pc) in R.A. The receiver, observing method, and calibration techniques are described, and the CO(7-6) spectra and maps are presented. The physical parameters and energetics of the molecular gas are discussed. The findings are compared with observations of other high-luminosity star-forming regions.

Howe, J. E.↗