SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Anisotropy of electronic metal work functions for zero and high electric fields perpendicular to surface measured by field emission and thermionic techniques
Electric field emissions at frequencies of (n + 1/2) times the electron cyclotron frequency have been generated in a large-scale electron beam experiment in a vacuum facility. These emissions arise when a contrastreaming beam configuration exists, the primary beam consisting of monoenergetic electrons (50 eV to 5 keV) and the other beam of lower-energy backscattered secondary electrons. It is suggested that the same mechanism could also be the source of the observed 3/2 times the electron cyclotron frequency emissions at auroral latitudes. In the absence of the beam-beam instability, weak oscillations were observed at the plasma frequency. In the latter case no significant modifications of the primary beam velocity distribution occurred, and the beam configuration is adequately described by single-particle motion in the ambient magnetic field.
A possible explanation for environmentally-induced discharges on geosynchronous satellites exists in the electric fields formed in the cavities between solar cells - the small gaps formed by the cover slides, solar cells, metallic interconnects and insulating substrate. When exposed to a substorm environment, the cover slides become less negatively charged than the spacecraft ground. If the resultant electric field becomes large enough, then the interconnect could emit electrons (probably by field emission) which could be accelerated to space by the positive voltage on the covers. An experimental study was conducted using a small solar array segment in which the interconnect potential was controlled by a power supply while the cover slides were irradiated by monoenergetic electrons. It was found that discharges could be triggered when the interconnect potential became at least 500 volts negative with respect to the cover slides. Analytical modeling of satellites exposed to substorm environments indicates that such gradients are possible. Therefore, it appears that this trigger mechanism for discharges is possible.
A possible explanation for environmentally-induced discharges on geosynchronous satellites exists in the electric fields formed in the cavities between solar cells - the small gaps formed by the cover slides, solar cells, metallic interconnects and insulating substrate. When exposed to a substorm environment, the cover slides become less negatively charged than the spacecraft ground. Hence, it is possible for metallic surfaces (usually silver mesh) to be at a negative potential in a cavity that has a 'positive' surface above it. If the resultant electric field becomes large enough, then the interconnect could emit electrons (probably by field emission) which could be accelerated to space by the positive voltage on the covers. An experimental study was connected using a small solar array segment in which the interconnect potential was controlled by a power supply while the cover slides were irridated by monoenergetic electrons. It was found that discharges could be triggered when the interconnect potential became at least 500 volts negative with respect to the cover slides. Analytical modeling of satellites exposed to substorm environments indicates that such gradients are possible. Therefore, it appears that this trigger mechanism for discharges is possible. Details of the experiment and modeling study are presented.
Introduction: The use of pulsed laser irradiation to simulate the short duration, high-energy conditions characteristic of micrometeorite impacts is now an established approach in experimental space weathering studies. The laser generates both melt and vapor deposits that contain nanophase metallic Fe (npFe(sup 0)) grains with size distributions and optical properties similar to those in natural impact-generated melt and vapor deposits. There remains uncertainty, however, about how well lasers simulate the mechanical work and internal (thermal) energy partitioning that occurs in actual impacts. We are currently engaged in making a direct comparison between the products of laser irradiation and experimental/natural hypervelocity impacts. An initial step reported here is to use analytical TEM is to attain a better understanding of how the microstructure and composition of laser deposits evolve over multiple cycles of pulsed laser irradiation. Experimental Methods: We irradiated pressed-powder pellets of San Carlos olivine (Fo(sub 90)) with up to 99 rastered pulses of a GAM ArF excimer laser. The irradiated surface of the sample were characterized by SEM imaging and areas were selected for FIB cross sectioning for TEM study using an FEI Quanta dual-beam electron/focused ion beam instrument. FIB sections were characterized using a JEOL2500SE analytical field-emission scanning transmission electron microscope (FE-STEM) optimized for quantitative element mapping at less than 10 nm spatial resolutions. Results: In the SEM the 99 pulse pressed pellet sample shows a complex, inhomogeneous, distribution of laser-generated material, largely concentrated in narrow gaps and larger depressions between grains. Local concentrations of npFe0 spherules 0.1 to 1 micrometers in size are visible within these deposits in SEM back-scatter images. Fig. 1 shows bright-field STEM images of a FIB cross-section of a one of these deposits that continuously covers the top and sloping side of an olivine grain. The deposit has 3 microstructurally distinct sub-layers composed of silicate glass with varying modal fractions and size distributions of npFe( sup 0) spherules, along with nanocrystalline silicate material. A relatively thin (50-300 nm) topmost surface layer has a high-concentration of npFe0 spherules 5-20 nm in size. Element mapping shows the layer to be enriched in Fe by a factor of 2.5 relative to the olivine substrate, with Mg and Si depleted by 20% and 10% respectively. This is compositionally complementary to the underlying, middle layer of the deposit that is depleted in Fe, enriched in Mg and has a much lower npFe0 concentration. A third layer of nanocrystalline olivine occurs at the substrate interface. Discussion: The FE-STEM results suggest the topmost layer is a vapor deposit, underlain by a thicker microstructurally complex melt-generated layer. The compositional relations suggest the melt layer was partially vaporized, preferentially losing more volatile elements (e.g., Fe). The vaporized material re-condensed to form the thin, npFe(sup 0)-rich surface deposit during or immediately after the scan cycle. Nanocrystalline olivine that grew within the melt layer as it formed and cooled is similar in volume and microstructure to what we have observed in the impact melt lining of a micrometeorite impact crater in olivine. This suggest the time-temperature relations attained in the laser sample may not be too different from a micrometeorite impact. Our TEM observations, however, do not show evidence for the same level of mechanical dam-age (e.g., fracturing) seen around the natural micrometeorite crater.
A solar limb flare was mapped using the Very Large Array (VLA) together with hard X-ray (HXR) spectral and spatial observations of the Solar Maximum Mission satellite. Microwave flux records from 2.8 to 19.6 GHz were instrumental in determining the burst spectrum, which has a maximum at 10 GHz. The flux spectrum and area of the burst sources were used to determine the number of electrons producing gyrosynchrotron emission, magnetic field strength, and the energy distribution of gyrosynchrotron-emitting electrons. Applying the thick target model to the HXR spectrum, the number of high energy electrons responsible for the X-ray bursts was found to be 10 to the 36th, and the electron energy distribution was approximately E exp -5, significantly different from the parameters derived from the microwave observations. The HXR imaging observations exhibit some similiarities in size and structure o the first two burst sources mapped with the VLA. However, during the initial burst, the HXR source was single and lower in the corona than the double 6 cm source. The observations are explained in terms of a single loop with an isotropic high-energy electron distribution which produced the microwaves, and a larger beamed component which produced the HXR at the feet of the loop.
Experimental study on use of field ionization and electron emission as ion sources for mass spectrometers
High voltage insulator for electron bombardment ion thruster has electric field directed through dielectric material and electrons emitted by field emission are constrained in negative junction region. Surface flashover and unstable operation are eliminated, and maximum voltage is limited only by dielectric strength of material, aluminum oxide in this case.
Chemically and microstructurally complex altered rims around grains in the finest size fraction (<20 micron) of the lunar regolith are the result of multi-stage processes involving both solar ion radiation damage and nanoscale deposition of impact or sputter-derived vapors. The formation of the rims is an important part of the space weathering process, and is closely linked to key changes in optical reflectance and other bulk properties of the lunar surface. Recent application of field-emission scanning transmission electron microscope techniques, including energy dispersive X-ray spectral imaging, is making it easier to unravel the "nano-stratigraphy" of grain rims, and to delineate the portions of rims that represent Radiation-Amorphized (RA) host grain from overlying amorphous material that represents vapor/sputter deposits. For the portion of rims formed by host grain amorphization (henceforth called RA rims), we have been investigating the feasibility of using Monte Carlo-type ion-atom collision models, combined with experimental ion irradiation data, to derive predictive numerical models linking the width of RA rims to the grain s integrated solar ion radiation exposure time.
Environmental barrier coated SiC-SiC ceramic matrix composites (CMCs) systems will play a crucial role in next generation turbine engines for hot-section component applications because of their ability to significantly increase engine operating temperatures with improved efficiency, reduce engine weight and cooling requirements. Advanced HfO2 and rare earth silicate environmental barrier coatings (EBCs), along with multicomponent hafnium and rare earth silicide EBC bond coats have been developed. The coating degradation mechanisms in the laboratory simulated engine thermal cycling, and fatigue-creep operating environments are also being investigated. This paper will focus on the microstructural and compositional evolutions of an advanced environmental barrier coating system on a SiC-SiC CMC substrate during the high temperature simulated durability tests, by using a Field Emission Gun Scanning Electron Microscopy, Energy Dispersive Spectroscopy (EDS) and Wavelength Dispersive Spectroscopy (WDS). The effects of Calcium-Magnesium-Alumino-Silicate (CMAS) from road sand or volcano-ash deposits on the degradation mechanisms of the environmental barrier coating systems will also be discussed. The detailed analysis results help understand the EBC-CMC system performance, aiming at the durability improvements to achieve more robust, prime-reliant environmental barrier coatings.
Introduction: The recent selection of two missions to Venus has renewed the importance of deter-mining weathering reactions between minerals and the Venusian atmosphere, and the spectral signatures of minerals before, during, and after these reactions. The rate at which weathering reactions progress also constrain show long unstable minerals will be present on the surface (e.g., [1]), and enables the use of mineralogy as a constraint on surface age(e.g., [2-3]).In order to gain an understanding of how mineral compositions and spectra change with weathering, we have begun conducting experiments in a 1 atm experimental setup at Wesleyan University. This setup exposes minerals to the temperature and most abundant gases of the Venus atmosphere (CO2, SO2, N2).We conducted initial experiments using biotite, calcite, and montmorillonite in order to test our methodology with minerals that may be relevant to recording the history of water on Venus. Methods: Experiments were conducted in Thermo Fisher Scientific Lindberg/Blue M Mini-Mite horizontal tube furnaces at Wesleyan University. Experiments used natural mineral chips and powders, and were conducted at 1 atmosphere and 460 °C under pre-mixed gases provided by Air Gas(Table 1). The furnaces are set up in a flow through configuration so that solid samples are exposed to a fixed gas composition, and quartz glass process tubes were used in all experiments (1/4” diameter for experiment V4, ½” diameter for all others). These conditions were maintained for the du-rations listed in Table 1, at which point the furnace was turned off with gas flowing until the sample was cool enough to extract under N2and be placed in a desiccator for storage. Run products were carbon coated and examined using a Hitachi SU5000 Field Emission Gun Scanning Electron Microscope (SEM) equipped with an EDAX Octane Pro EDS detector located at Wesley-an University. Visible-Near Infrared Spectroscopy (VNIR) analysis was performed on powdered samples under a nitrogen atmosphere using an ASD Fieldspec Proover the 350-2500 nm range. Powdered mineral samples were milled to a particle size of < 45μm and were spiked with an internal standard (Al2O3, corundum) to obtain quantitative mineralogy. Samples were analyzed using a Panalytical X’Pert pro X-ray Diffractometer (XRD), with an X’Celerator high speed detector and Co Kα radiation, with data collected at a step size of 0.02 ̊/minute step counting rate from 2 to 80 degrees 2θ at 45 mA/40kV in the X-ray Diffraction Laboratory located at NASA Johnson Space Center. Materials Data Inc (MDI) software suite, JadeTMv9 was used for Rietveld refinement to determine phase abundances and mineral identification by comparing XRD patterns to International Center for Diffraction Data (ICDD) database patterns. Table 1: Experimental matrix. Experiment Name Duration (Days)Gas Com-position (trace gas)MineralsV487SO2/N2(1.4%)Montmorillonite, biotiteV519SO2/N2(1.4%)CalciteV619CO2/SO2/N2(1.4% SO2, 2.1% N2)Montmorillonite, biotiteV828SO2/N2(1.4%)Biotite, calcite Results: Calcite. In both experiments, calcite was exposed to the SO2/N2gas mixture, and in both experimental run products, XRD analysis detected anhydrite, which is consistent with EDS measurements conducted in the SEM. The XRD analyses show greater amounts of anhydrite present after 28 days than 19, suggesting the calcite reaction progressed further given longer duration. Grain surface morphology as seen in the SEM also shows secondary mineral growth (Fig. 1). VNIR spectra show no change, as expected since anhydrite lacks spectral features in this wavelength range. Montmorillonite. Montmorillonite was exposed to two different gas mixtures, the SO2/N2mix and CO2/SO2/N2mix over different durations (87 and 19 days, respectively). VNIR analyses of both run products show a reduction in the 1441and1910 nm water features as well as a shift of the 1411 and 2011 nm features to shorter wavelengths that may indicate re-structuring in the crystal lattice and the production of amorphous phases [4]. XRD results are consistent with this, showing a shift of the 001 peak from 15Åto 10Åin both run products. The amount of X-ray amorphous material in the montmorillonite run products was greater than that present in the unreacted clay, being the greatest in the 87 day V4 experiment. No other secondary phases were detected in the run products, however sulfur was present in EDS analyses of powder samples.
JAXA’s Hayabusa2 spacecraft successfully recovered samples from Cb-type asteroid Ryugu and returned samples are now under detailed scrutiny by the international community. The ongoing initial analysis has so far revealed that the Ryugu samples are pristine primitive asteroidal materials mostly composed of secondary minerals such asphyllosilicates, carbonates, Fe sulfides and magnetite associated with organic matter [e.g., 1]. However, some samples contain small amounts of anhydrous silicates and oxides such as olivine that are thought to be the precursors of the Ryugu parent asteroid. Their sizes are mostly <5 mm, and detailed mineralogical analysis is possible using an electron microprobe with field emission gun (FE-EPMA). Here we report results of our extensive FE-EPMA analysis of an hydrous minerals focusing on olivine to compare with literature chondritic data. We also performed synchrotron XRD of olivine crystals to evaluate the shock degree of Ryugu samples. These analyses allow us to discuss the formation of Ryugu in light of the solar system early evolution.
The high-pressure polymorph of zircon (Zr2SiO4) is reidite, a phase with the scheelite structure that was first discovered to form at ca. 12 GPa in static high-pressure experiments [1]. Reidite was subsequently found to occur in naturally shocked zircons from several terrestrial impact localities [2,3], as well as in shock recovery-reverberation experiments performed above 20 GPa [4]. The nature and distribution of reidite occurrences in terrestrial impact localities has pointed to its potential use as a shock pressure indicator, as well as to the importance of understanding its age-reset effects in zircon geochronology [3]. In this study we have used coordinated SEM/Electron Backscatter Diffraction (EBSD) and Field-Emission Scanning Transmission Electron Microscopy (FE-STEM) to study the micro- and nanostructure of reidite and its shocked zircon host produced at 21.2 GPa under experimental shock recovery/reverberation conditions [5]. Our results document the TEM microstructure of reidite formed at a 21.2 GPa experimental shock pressure that is significantly lower than that observed in previous studies [4]. At these conditions the sample developed a diverse set of microstructures that have not been previously documented on the TEM scale.
The flux of objects impacting the surfaces of solar system airless bodies is dominated by micrometeoroids less than 1 mm diameter whose impact effects play a major role in the space weathering of airless body surfaces. To obtain better understanding of how small scale impact effects vary as a function of impact speed in an important lunar and asteroidal mineral, we produced artificial microcraters in San Carlos olivine using Fe metal dust particles 0.10 to 5 µm in diameter electrostatically accelerated to speeds between 0.35 to 25 km s-1. The crater morphologies, size distrrubiton and microstruc-tures were characterized by field-emission SEM (FE-SEM) and also by FIB cross sectioning of selected craters for field-emission scanning transmission electron microscopy (FE-STEM). These same techniques were also applied to study a natural 20 µm-diameter microcrater in a olivine grain on the surface of lunar rock 12075. Measured microcrater diameters in the experimental sample range between 0.20 to 5 µm with larger craters having more irregular outlines dominated by spallation fractures. FE-SEM and FE-STEM imaging docu-ment the formation of shock melt in the size population of experimental craters below approximately 1 µm in diameter, corresponding to particle impact speeds in the 10-25 km s-1 range. The natural olivine crater exhibits similar shock melt features along the perimeter of its cavity, but the shock melt also contains nanophase Fe metal particles, something not observed in the experimental samples. FE-STEM imaging of the experimental craters reveals complex shock-generated dislocation and nanofracture microstructures in zones extend-ing 1-2 µm into the olivine from the crater cavity. The natural microcrater shows a lower density of shock-generated disloca-tions that extends a factor of 2 deeper into the the olivine than in the experimental samples.
We apply a DC-electric field model to the analysis of soft and hard X-ray observations of a solar flare observed by Yohkoh and the Compton Gamma Ray Observatory (CGRO) on 6 September 1992. The flare was observed simultaneously in the soft X-ray Ca XIX line by the Yohkoh Bragg Crystal Spectrometer (BCS) and in hard X-rays (greater than 50 keV) by the CGRO Burst and Transient Spectrometer Experiment (BATSE). A strong stationary component of Ca XIX emission was present at the start of impulsive hard X-ray emission indicating an extended phase of heating prior to the production of energetic nonthermal electrons. We interpret the preflare Ca XIX emission as a signature of Joule heating by field-aligned currents. We relate the temporal variation of impulsive hard X-ray emission to the rate of runaway electron acceleration by the DC-electric field associated with the current. We find that the initial rise in hard X-ray emission is consistent with electron acceleration by a DC-electric field that increased from a preflare value of less than approximately 10(exp -5) V/cm to approximately (9 +/- 1) x 10(exp -5) V/cm at the time of the first hard X-ray peak and then remained constant during the rest of the impulsive phase. We attribute the increase in electric field strength to the formation of a current sheet at the reconnection point of two loop structures. The decrease in hard X-ray emission after flare maximum is consistent with a reduction in the number of runaway electrons due to an increase in coronal density produced by chromospheric evaporation. The increased density quenches the runaway process by enhancing collisional thermalization of electrons. To avoid the generation of an unrealistically large magnetic field, the flaring region must be highly filamented into greater than approximately 10(exp 6) oppositely directed current channels of approximately 30 cm width with an initial preflare current of approximately 3 x 10(exp 10) A per channel.
Using simultaneous observations from the DE-1 High-Altitude Plasma Instrument and the Plasma Wave Instrument, a study is made of 28 auroral-zone crossings, equally divided among dayside and nightside cases covering a range of Kp values from 1- to 8. In the diffuse auroral region, electrostatic emissions of frequencies up to a few kHz are associated with low-energy field-aligned electron beams. Of 18 cases (11 nightside; 7 dayside) examined at high resolution in the particle data, 15 (9 nightside; 6 dayside) exhibited field-aligned beams with electrostatic waves. In most cases, the beams were upward-directed, but occasionally they traveled both up and down the field line. The electrostatic emissions are interpreted as electron-acoustic waves excited by the field-aligned beams.
The decimetric emission consists partly of thermal radiation from the planetary disk and partly of nonthermal radiation from a region of larger angular extent and is thought to result from synchrotron emission by relativistic electrons in the magnetic field. Four topics relating to the decimetric emission are discussed. (1) A comparison is made of maps giving detailed brightness contours. One was obtained for epoch 1963.8 and was at a wavelength of 10.4 cm. The second was for epoch 1967.2 at 21.3 cm. (2) Interferometric data at 21.1 cm taken in April 1968 and May 1979 indicate that the emission centroid is fixed in Jupiter and rotates with it. (3) Circular polarization observations are described and are used to obtain a surface magnetic field strength at the equator between 3.2 and 15.2 gauss. (4) An upper limit on the Faraday rotation is used to set an upper limit on the density of thermal electrons surrounding Jupiter, and uncertainties in the results are discussed.
The dust charging by electron impact is an important dust charging process in Astrophysical, Planetary, and the Lunar environments. Low energy electrons are reflected or stick to the grains charging the dust grains negatively. At sufficiently high energies electrons penetrate the grain leading to excitation and emission of electrons referred to as secondary electron emission (SEE). Available theoretical models for the calculation of SEE yield applicable for neutral, planar or bulk surfaces are generally based on Sternglass Equation. However, viable models for charging of individual dust grains do not exist at the present time. Therefore, the SEE yields have to be obtained by some experimental methods at the present time. We have conducted experimental studies on charging of individual micron size dust grains in simulated space environments using an electrodynamic balance (EDB) facility at NASA-MSFC. The results of our extensive laboratory study of charging of individual micron-size dust grains by low energy electron impact indicate that the SEE by electron impact is a very complex process expected to be substantially different from the bulk materials. It was found that the incident electrons may lead to positive or negative charging of dust grains depending upon the grain size, surface potential, electron energy, electron flux, grain composition, and configuration. In this paper we give a more elaborate discussion about the possible effects of the AC field in the EDB on dust charging measurements by comparing the secondary electron emission time-period (tau (sub em) (s/e)) with the time-period (tau (sub ac) (ms)) of the AC field cycle in the EDB that we have briefly addressed in our previous publication.