Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FACET”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

JPL tests of a LaJet concentrator facet

A LaJet Energy Company (LEC) concentrator facet, 60 in. in diameter, was tested for imaging quality. The following two methods were used: (1) autofocus tests with a point source of light at the facet's radius of curvature; and (2) tests with the Sun close to the horizon as a distant source. The tests of the LaJet facet indicate that all of the solar image reflected by an LEC 460 solar concentrator made of like facets should fall within a 9-in. aperture if the outer facets are carefully adjusted. Such a concentrator would have acceptable performance, but complete evaluation must be made with an assembled concentrator.

Dennison, E. W.↗
NASA NTRS1989

Measured and predicted root-mean-square errors in square and triangular antenna mesh facets

Deflection shapes of square and equilateral triangular facets of two tricot-knit, gold plated molybdenum wire mesh antenna materials were measured and compared, on the basis of root mean square (rms) differences, with deflection shapes predicted by linear membrane theory, for several cases of biaxial mesh tension. The two mesh materials contained approximately 10 and 16 holes per linear inch, measured diagonally with respect to the course and wale directions. The deflection measurement system employed a non-contact eddy current proximity probe and an electromagnetic distance sensing probe in conjunction with a precision optical level. Despite experimental uncertainties, rms differences between measured and predicted deflection shapes suggest the following conclusions: that replacing flat antenna facets with facets conforming to parabolically curved structural members yields smaller rms surface error; that potential accuracy gains are greater for equilateral triangular facets than for square facets; and that linear membrane theory can be a useful tool in the design of tricot knit wire mesh antennas.

Fichter, W. B.↗
DOE OSTI2016

Orientation-Dependent Surface Faceting in UO{sub 2}

The surface behavior of UO{sub 2} plays an important role throughout the lifetime of this widely-used commercial nuclear fuel, from manufacturing to waste storage. UO{sub 2} surface properties affect fuel swelling behavior by determining the morphology, size and distribution of fission gas bubbles. Additionally, UO{sub 2} surface characteristics influence fracture behavior, which is controlled by the thermodynamics of fracture surfaces. Therefore, detailed understanding of the fundamental surface behavior will help advance prediction of the fuel performance of UO{sub 2}. Due to significant anisotropy in surface tension, faceting features form after annealing in both UO{sub 2} and many other crystalline materials. Knowledge of the correlation between crystallographic orientation and surface faceting features will expand the fundamental knowledge of UO{sub 2} surface characteristics, leading to a better understanding of fission gas swelling and fracture mechanisms. Inherent characterization technique limited previous studies on the crystallographic orientation of UO{sub 2} surface facets to low Miller index surfaces in single crystal specimens. In this study, synchrotron Laue microdiffraction was utilized to examine the crystallographic orientation of grains on the coarse surface of a polycrystalline UO{sub 2} specimen. The results were then compared with the surface morphology, obtained from scanning electron microscopy (SEM), so that a general correlation between the surface faceting features and crystallographic orientation in UO{sub 2} can be established. Both the fundamental surface characteristics and the crystallographic orientation measurements obtained in this study help advance the experiment validation of MARMOT, a mesoscale multi-physics code that predicts the coevolution of microstructure and properties within reactor fuel during its lifetime in the reactor. The MARMOT code is an indispensable component of the MOOSE-BISON-MARMOT (MBM) code suite that has been developed by Idaho National Laboratory to enable next generation fuel performance modeling capability as a part of the Nuclear Energy Advanced Modeling and Simulation (NEAMS) Program Fuels Product Line (FPL). In this study, the surface-faceting features of UO{sub 2} were found to be dominated by the triple-plane structure and its variants. With this knowledge, by measuring the directions of the <110> edges, the crystallographic orientation of a surface UO{sub 2} grain can be precisely deduced in most regions of the standard stereogram triangle (SST) of the surface normal. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Probing Acid–Base Properties of Anatase TiO 2 Nanoparticles with Dominant {001} and {101} Facets Using Methanol Chemisorption and Surface Reactions

In the present study, we investigate the surface acid-base properties of anatase TiO 2 nanomaterials with dominant {101} and {001} facets via methanol titrations. Two anatase nanoparticles, TiO 2 (101) and TiO 2 (001), with well-defined morphology are prepared. TiO 2 (101) is predominantly enclosed by the {101} facets (> 90%), and TiO 2 (001) contains ~46% {001} facets and ~54% {101} facets. Upon adsorption of methanol 423 K, DRIFTS measurements show that both molecular and dissociative adsorption occurs on TiO 2 (101), while dissociative adsorption dominates on TiO 2 (001). During methanol TPD, TiO 2 (001) mainly generates acid-base product dimethyl ether and thermal cracking products CO and H 2 , as anticipated. In contrast, substantial amounts of formaldehyde and methane also desorb from TiO 2 (101), suggesting strong participation of surface defects (e.g., oxygen vacancies).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

The interplay between surface facet and reconstruction on isopropanol conversion over SrTiO 3 nanocrystals

Strontium titanate (SrTiO 3 ) is an extensively investigated perovskite for various applications due to its optical, electrical and chemical properties. To gain an in-depth understanding of the active sites involved in heterogeneous catalysis over the broadly used SrTiO 3 (STO), we studied a model reaction, isopropanol conversion, on three differently shape-controlled nanocrystals: cube, truncated cube and dodecahedra. SEM, XRD and XPS confirmed the morphology, phase and composition of STO shapes. Low energy ion scattering (LEIS) revealed the occurrence of surface reconstruction over STO shapes during O 2 pretreatment at different temperatures. Based on the catalytic activities, scanning transmission electron microscopy images and density functional theory calculations, the step sites on STO derived from surface reconstruction were proposed to be the active sites for isopropanol conversion. This was further confirmed by steady state isotopic kinetic analysis (SSITKA) which demonstrated similar intrinsic turnover frequencies (TOFs) for the differently reconstructed STO shapes. It is concluded that the crystal facets impose an indirect effect on the catalysis of STO via controlling the degrees of surface reconstruction: the less stable STO (1 1 0) facet (dodecahedra) leads to more step sites after reconstruction and hence higher overall reaction rate than the more stable (1 0 0) facet (cube). This work highlights the important interplay between the crystal facet and surface reconstruction in controlling the nature and density of active sties and thus catalysis over complex oxides.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

The crystal facet-dependent electrochemical performance of TiO 2 nanocrystals for heavy metal detection: Theoretical prediction and experimental proof

Tailored design/fabrication of electroanalytical materials with highly-active exposed crystal planes is of great importance for the development of electrochemical sensing. In this work, combining experimental and theoretical efforts, we reported a facile strategy to fabricate TiO 2 nanocrystals with tunable electrochemical performance for heavy metal detection. Density functional theory (DFT) calculations indicated that TiO 2 (001) facet showed relative larger adsorption energy and lower diffusion energy barrier toward heavy metal ions, which is favorable for obtaining better electrochemical stripping behaviors. Based on this prediction, a series of TiO 2 nanocrystals with different ratios of exposed (001) and (101) facets were synthesized. Electrochemical stripping experiments further demonstrated that with the increase of the percentage of exposed (001) facet, the sensitivity toward Pb(II) and Cd(II) was increased accordingly. When the percentage of exposed (001) facet was increased from 7% to 80%, the sensitivity increased by 190% and 93% for Pb(II) and Cd(II), respectively. In conclusion, our work provides an effective route to construct advanced electroanalytical materials for sensing.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Effect of single atom Platinum (Pt) doping and facet dependent on the electronic structure and light absorption of Lanthanum Titanium Oxide (La 2 Ti 2 O 7 ): A Density Functional Theory study

Charge generation and separation are two key processes for semiconductor photocatalysis. Here, we use Pt as a single atom catalyst to systematically examine the facet-dependent electronic band structure and light absorption of the layered perovskite-type wide-gap semiconductor, lanthanum titanium oxide (La 2 Ti 2 O 7 , LTO) by means of density functional theory simulations. In this study, it is found that single Pt atom doping of different LTO surfaces (here, (100), (101) and (001)) can not only create states in the bandgap that would promote the formation of recombination centers, but also shift the optical absorption edge to the visible region. Interestingly, the Pt doping forms a heterojunction, with the valence band maximum consisting of Pt states and the conduction band minimum consisting of LTO states, respectively. To study the facet dependent surface activity, acetic acid (CH 3 COOH) was used as a model molecule to investigate the adsorption and charge transfer on the (101), (100) and (001) Pt-LTO surface facets. The results show that the (101) facet could enable stronger adsorption of CH 3 COOH by promoting more electron transfer during the interfacial interaction. Our theoretical findings aim to promote the design and optimization of the single atom catalysts (SACs) for photocatalytic applications and other broad catalysis systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Tuning Li 2 O 2 Formation Routes by Facet Engineering of MnO 2 Cathode Catalysts

In lithium-oxygen batteries, the solubility of LiO 2 intermediates in the electrolyte regulates the formation routes of the Li 2 O 2 discharge product. High-donor-number electrolytes with a high solubility of LiO 2 tend to promote the formation of Li 2 O 2 large particles following the solution route, which eventually benefits the cell capacity and cycle life. Here, we propose that facet engineering of cathode catalysts could be another direction in tuning the formation routes of Li 2 O 2 . In this work, fi-MnO 2 crystals with high occupancies of {111} or {100} facets were adopted as cathode catalysts in Li-O 2 batteries with a tetra(ethylene)glycol dimethyl ether electrolyte. The {111}-dominated beta-MnO 2 catalyzed the formation of the Li 2 O 2 discharge product into large toroids following the solution routes, while {100}-dominated beta-MnO 2 facilitated the formation of Li 2 O 2 thin films through the surface routes. Further computational studies indicate that the different formation routes of Li 2 O 2 could be related to different adsorption energies of LiO 2 on the two facets of beta-MnO 2 . Our results demonstrate that facet engineering of cathode catalysts could be a new way to tune the formation route of Li 2 O 2 in a low-donor-number electrolyte. Here, we anticipate that this new finding would offer more choices for the design of lithium-oxygen batteries with high capacities and ultimately a long cycle life.

25 ENERGY STORAGE↗
DOE OSTI2016

Atomic-scale determination of active facets on the MoVTeNb oxide M1 phase and their intrinsic catalytic activity for ethane oxidative dehydrogenation

Atomic resolution aberration-corrected HAADF-STEM imaging has been used to directly image the basal (001) plane of the catalytically relevant M1 phase in MoVTeNb complex oxides. Facets {010}, {120} and {210} are identified as the most stable lateral terminations of the crystals. For each of these surface facets the average concentration of active sites is determined directly from the images. The most stable {010} facet does not expose active sites and is therefore regarded to be inactive. As a consequence, large flattened M1 particles are concluded to have a lower activity than other morphologies. This hypothesis is validated by a statistical analysis of two samples with rod vs. plate morphology. The concentration of sites and the catalytic activity in ethane oxidative dehydrogenation correlate perfectly, demonstrating quantitatively that the differences in reactivity between MoVTeNbOx catalysts of equal crystallinity and chemical composition depend primarily on the terminating facets that constitute the elongated catalyst particles.

MoVTeNbO, Oxidative Dehydrogenation, M1 phase, STE↗
DOE OSTI2017

Silicon Wafers with Facet-Dependent Electrical Conductivity Properties

By breaking intrinsic Si (100) and (111) wafers to expose sharp {111} and {112} facets, electrical conductivity measurements on single and different silicon crystal faces were performed through contacts with two tungsten probes. While Si {100} and {110} faces are barely conductive at low applied voltages, as expected, the Si {112} surface is highly conductive and Si {111} surface also shows good conductivity. Asymmetrical I–V curves have been recorded for the {111}/{112}, {111}/{110}, and {112}/{110} facet combinations because of different degrees of conduction band bending at these crystal surfaces presenting different barrier heights to current flow. In particular, the {111}/{110} and {112}/{110} facet combinations give I–V curves resembling those of p–n junctions, suggesting a novel field effect transistor design is possible capitalizing on the pronounced facet-dependent electrical conductivity properties of silicon.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Facet-Dependent Water Inhibition of Alkanol Dehydration on TiO2 via Distinct Water–Alkanol Complexes

Water is ubiquitous in biomass-derived feeds, yet its molecular impact on oxygen-elimination reactions remains poorly understood, particularly for catalysts exposing different facets. Here, we utilize well-defined TiO2 nanocrystals with dominant (101) and (001) facets to reveal a pronounced facet-dependent effect of water, where inhibition for dehydration of isopropanol (IPA) on the TiO2(001) surface is about four times more severe than TiO2(101). Through a combination of in situ solid state NMR, in situ infrared spectroscopy, kinetics studies, and theoretical calculations, we demonstrate that this disparity arises from the formation of distinct alkanol-water complex intermediates. On TiO2(001), IPA undergoes dissociative adsorption to form an isopropoxide-H2O complex that readily drives the surface into a complex-dominated regime. This pathway increases the activation barrier for C–H cleavage by 40 kJ mol-1 by inducing a disordered transition state. In contrast, TiO2(101) favors molecular IPA adsorption with weak hydrogen bonding to water, resulting in a smaller complex formation constant and a much smaller activation barrier increase (25 kJ mol-1). By quantitatively linking facet-dependent complex coverage to transition-state destabilization, this work moves beyond simple site-blocking models and provides a conceptual framework for designing catalysts that remain active in water-containing environments

Hu, Wenda↗
DOE OSTI2023

Facet-dependent strong metal-support interactions control the C–O bond activation

Reducible metal oxides are selective and effective for C–O bond scission of hydrodeoxygenation reactions via the reverse Mars-van Krevelen mechanism. Creating efficient redox centers while minimizing metal surfaces leads to highly selective catalysts. Single noble metal atoms activate the surface M–O bond, but the catalyst activity is limited due to low loading. Here, we report that the strong metal-support interaction between Ir and CeO 2 is facet sensitive, and certain facets regulate the C–O bond cleavage. At 300°C reduction, Ir is mostly encapsulated on an octahedron by (111) facets but remains exposed by (110) facets. The former is selective, whereas the latter is not. In conclusion, density functional theory indicates that Ir encapsulation is favored on (111) under reaction conditions, and oxygen vacancies more readily form on encapsulated Ir than on pristine ceria.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

CO 2 electro-reduction on Cu 3 P: Role of Cu(I) oxidation state and surface facet structure in C 1 -formate production and H 2 selectivity

We report the catalytic activity and mechanism of copper(I) phosphide, Cu 3 P, with predominant [00Ι] facet exposure for the electrochemical reduction of CO 2 (CO 2 RR) to formic acid. Crystalline nanosheets of this compound that show a preferential [00Ι] facet orientation exhibit undiminished CO 2 RR activity after 16 hours with full retention of crystal structure and surface chemical speciation and no detectable corrosion. In contrast to the range of products formed on Cu metal, CuO, and Cu 2 O, the CO 2 RR on Cu 3 P [00Ι] produces mainly hydrogen and formate as the sole carbon product in KHCO 3 electrolyte. Analysis of the Cu 3 P [00Ι] facet by HAADF-STEM was used to determine the surface lattice structure, while both XPS and Auger spectroscopies were used to determine the surface chemical speciation from the kinetic energies of ionized electrons. The presented analysis identifies isolated trigonal CuP 3 sites on the Cu 3 P[00Ι]-Cu 3 P 3 terminated surface and the Cu(I) oxidation state as precursor to the active catalyst. The CO 2 RR selectivity to formate and the higher turnover rate for H 2 production on the [00Ι] facet allows a structure-activity analysis and chemical mechanism to be proposed. Formation of a surface hydride at isolated *H-CuP 3 sites is proposed as the catalytic site in forming both H 2 and formate, while the long Cu—Cu separation retards forming C-C coupling products. In conclusion, these results disprove previously published claims of Cu(I) oxidation state as a sufficient criterion to promote CO 2 RR to C 2+ products, show that stronger bonded hydrides, *H-CuP 3 on Cu 3 P, favor production of the C1 product formate over all other carbon products, and predict that stronger formate binding (bidentate) is needed for CO 2 RR currents to compete with H 2 production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2015

TEM and XPS studies on the faceted nanocrystals of Ce{sub 0.8}Zr{sub 0.2}O{sub 2}

Faceted nanocrystals of Ce{sub 0.8}Zr{sub 0.2}O{sub 2} synthesised by co-precipitation method were characterised by X-ray diffraction, high-resolution transmission electron microscopy, thermogravimetry–differential scanning calorimetry and X-ray photoelectron spectroscopy techniques. The nanocrystals were highly faceted and exhibited a cubic phase. X-ray photoelectron spectroscopy analyses confirmed the presence of vacancy related defects and revealed the presence of ~ 22% of Ce{sup 3} {sup +} in the nanopowders. High-resolution transmission electron microscopy results confirmed that the nanocrystal sizes are around 31 ± 5 nm and the obtained hexagonal cross-section shape is bound by hexagonal (111) and square (100) facets. The shape-controlled nanocrystals were synthesised without using any surfactants or complexing agents and retained their morphology beyond 800 °C. This is a simple and easy method for producing shape-controlled Ce{sub 0.8}Zr{sub 0.2}O{sub 2} nanoparticles which can be used for catalytic conversion and other related advanced technological areas. - Graphical abstract: Display Omitted - Highlights: • Synthesis of Ce{sub 0.8}Zr{sub 0.2}O{sub 2} faceted nanocrystal of hexagonal morphology. • Nanopowders synthesised without any surfactant; retained morphology beyond 800 °C. • XPS analyses confirm the potential of these powders for catalytic applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Alloying induces directionally-dependent mobility and alters migration mechanisms of faceted grain boundaries

Faceted grain boundaries exhibit unusual segregation and migration tendencies. To gain a deeper understanding of how solute atoms interact with faceted interfacial structures during migration, this study probes the migration behavior of a faceted Σ11 boundary in Cu doped with Ag atoms. Furthermore, the solutes are found to segregate to the facet with more free volume and strongly reduce boundary velocity in one migration direction, but not the other, due to the presence of a directionally-dependent motion mechanism that can escape solute pinning and therefore speed up migration. Hence, a new mechanism of chemically-induced anisotropy in grain boundary mobility is uncovered by these simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2016

CO-CO coupling on Cu facets: Coverage, strain and field effects

We present a DFT study on the effect of coverage, strain, and electric field on CO-CO coupling energetics on Cu (100), (111), and (211). Our calculations indicate that CO-CO coupling is facile on all three facets in the presence of a cation-induced electric field in the Helmholtz plane, with the lowest barrier on Cu(100). The CO dimerization pathway is therefore expected to play a role in C 2 formation at potentials negative of the Cu potential of zero charge, corresponding to CO 2 /CO reduction conditions at high pH. Both increased *CO coverage and tensile strain further improve C-C coupling energetics on Cu (111) and (211). Since CO dimerization is facile on all 3 Cu facets, subsequent surface hydrogenation steps may also play an important role in determining the overall activity towards C 2 products. Adsorption of *CO, *H, and *OH on the 3 facets were investigated with a Pourbaix analysis. Here, the (211) facet has the largest propensity to co-adsorb *CO and *H, which would favor surface hydrogenation following CO dimerization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Syntheses of Colloidal F:In 2 O 3 Cubes: Fluorine-Induced Faceting and Infrared Plasmonic Response

Cube-shaped nanocrystals (NCs) of conventional metals like gold and silver generally exhibit localized surface plasmon resonance (LSPR) in the visible region with spectral modes determined by their faceted shapes. Yet, faceted NCs exhibiting LSPR response in the infrared (IR) region are relatively rare. Here, we describe the colloidal synthesis of nanoscale fluorine-doped indium oxide (F:In 2 O 3 ) cubes with LSPR response in the IR region, wherein fluorine was discovered to both direct the cubic morphology and act as an aliovalent dopant. Single-crystalline 160 nm F:In 2 O 3 cubes terminated by (100) facets and concave cubes were synthesized using a colloidal heat-up method. The presence of fluorine was found to impart higher stabilization to the (100) facets through density functional theory calculations that evaluated the energetics of F-substitution at surface oxygen sites. These calculations suggest that the cubic morphology results from surface binding of F atoms. In addition, fluorine acts as an anionic aliovalent dopant in the cubic bixbyite lattice of In 2 O 3 , introducing a high concentration of free electrons leading to LSPR. We confirmed the presence of lattice fluorine dopants in these cubes using solid-state 19 F and 115 In nuclear magnetic resonance spectroscopy. The cubes exhibit narrow, shape-dependent multimodal LSPR extinction peaks due to corner- and edge-centered modes. The spatial origin of these different contributions to the spectral response is directly visualized by electron energy loss spectroscopy in a scanning transmission electron microscope.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Molecular Driving Force for Facet Selectivity of Sequence-Defined Amphiphilic Peptoids at Au–Water Interfaces

Shape-controlled colloidal nanocrystal syntheses often require facet-selective solution-phase chemical additives to regulate surface free energy, atom addition/migration fluxes or particle attachment rates. Because of their highly tunable properties and robustness to a wide range of experimental conditions, peptoids represent a very promising class of next generation functional additives for control over nanocrystal growth. However, understanding the origin of facet selectivity at the molecular level is critical to generalizing their design. In this work, we employ molecular dynamics simulations and biased sampling methods and report stronger selectivity to Au(111) than to Au(100) for Nce3Ncp6, a peptoid that has been shown to assist the formation of five-fold twinned Au nanostars. We find that facet-selectivity is achieved through synergistic effects of both peptoid-surface and solvent-surface interactions. Moreover, the amphiphilic nature of Nce3Ncp6 together with the order of peptoid-peptoid and peptoid-surface binding energies, i.e., peptoid-Au(100) < peptoid-peptoid < peptoid-Au(111), further amplifies its distinct collective behavior on different Au surfaces. Our studies provide a fundamental understanding of the molecular origin of facet-selective adsorption and highlight the possibility of future designs and uses of sequence-defined peptoids for predictive syntheses of nanocrystals with designed shapes and properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗