Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Energy absorption”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Room Temperature Stamping of High-Strength Aluminum for Lightweight Structural Automotive Components

The use of aluminum (Al) 7xxx series in automobile structural applications is limited by factors such as its low room-temperature formability in T6 temper and the need for off-line artificial aging to regain high strength if it is formed in soft temper. In this study, two tempers were established that enable Al 7075 blanks to be room temperature stamped to create side impact beams that achieve near-T6 strength without post-forming artificial aging. It is shown that natural aging at room temperature, after solution treatment and before stamping, provides an alternative to high temperature pre-aging and hot stamping techniques in 7xxx alloys. Both tempers enabled room temperature stamping of the beams without cracking, indicating good formability. The Al beams were ~38% lighter than the benchmark boron steel beam. Further, the hardness in the low-deformation regions of the stamped Al beams were within 88% of a conventional 7075-T6 sheet. Paint-bake treatment of the beams appeared to cause over aging, lowering the ultimate tensile strength and ductility. Finite element three point bending simulations of the beams showed higher bending force and energy absorption before failure for the Al 7075 showing good promise for 7xxx series Al as a light-weight alternative to steel beams.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of Topology on Transient Dynamic and Shock Response of Polymeric Lattice Structures

Architected cellular materials, such as lattice structures, offer potential for tunable mechanical properties for dynamic applications of energy absorption and impact mitigation. In this work, the static and dynamic behavior of polymeric lattice structures was investigated through experiments on octet-truss, Kelvin, and cubic topologies with relative densities around 8%. Here, dynamic testing was conducted via direct impact experiments (25–70 m/s) with high-speed imaging coupled with digital image correlation and a polycarbonate Hopkinson pressure bar. Mechanical properties such as elastic wave speed, deformation modes, failure properties, particle velocities, and stress histories were extracted from experimental results. At low impact velocities, a transient dynamic response was observed which was composed of a compaction front initiating at the impact surface and additional deformation bands whose characteristics matched low strain-rate behavior. For higher impact velocities, shock analysis was carried out using compaction wave velocity and Eulerian Rankine–Hugoniot jump conditions with parameters determined from full-field measurements.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High strain rate deformation of aged TRIP Ti-10V-2Fe-3Al (wt.%) examined by in-situ synchrotron X-ray diffraction

Transformation Induced Plasticity (TRIP) is a promising avenue for tailoring the work hardening response of metastable $β$ titanium (Ti) alloys. Here we show that aged TRIP Ti-10V-2Fe-3Al (wt.%) maintains higher elongations and flow stresses as strain rate increases, if phase stability and microstructural characteristics are tuned. Low temperature aging influences the matrix $β$ phase stability by $ω$ phase precipitation, which affords a promising way to impact the TRIP effect and obtain desirable mechanical properties, ranging from high damping capacity to good strength/ductility combinations. Although TRIP is active during quasi-static and dynamic testing up to 2000 s –1 , increasing aging time and/or strain rate reduces the overall propensity for the TRIP effect and extent of transformation, which occurs rapidly just at the onset of yielding. Importantly, TRIP with $ω$ phase precipitation provides interesting alloying, microstructure, and property design strategies for engineering applications like lightweight protective structures, where high strains and the need for energy absorption are encountered.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A mechanistic study on environment gas in laser powder bed fusion

A variety of protective or reactive environmental gases have recently gained growing attention in laser-based metal additive manufacturing (AM) technologies due to their unique thermophysical properties and the potential improvements they can bring to the build processes. However, much remains unclear regarding the effects of different gas environments on critical phenomena in laser AM, such as rapid cooling, energy coupling, and defect generation. Through simultaneous high-speed synchrotron x-ray imaging and thermal imaging, we identify distinct effects of two environmental gases in laser AM and gained a deeper understanding of the underlying mechanisms. Compared to the commonly used protective gas, argon, it is found that helium has a negligible effect on cooling the part. However, helium can suppress unstable keyholes by decreasing effective energy absorption, thus mitigating keyhole porosity generation and reducing pore size under certain processing conditions. In conclusion, these observations provide guidelines for the strategic use of environmental gases in laser AM to produce parts with improved quality.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Direct current in a stirred optical lattice

We study how the energy dispersion of bosonic atoms loaded into an optical lattice becomes modified due to periodic circular stirring of the lattice to the second order in the strength of stirring. If the lattice breaks mirror symmetry, the bosonic atoms may acquire a nonzero group velocity at the center of the Brillouin zone and produce a nonzero direct current. Furthermore, this effect is similar to the circular photogalvanic effect in solid-state physics. It can be used to transport neutral bosonic atoms in an optical lattice over a given distance in an arbitrary direction. However, when the drive frequency is detuned to avoid resonant transitions with energy absorption, we argue that the induced current is not persistent, but transient. An experimental study of the relaxation of the induced current can provide insight about equilibrization in driven systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Improving the performance of PM6 donor polymer by random ternary copolymerization of BDD and DTBT segments

Developing high-performance wide bandgap polymer donors to match the rapidly growing non-fullerene small molecule acceptors (NF-SMAs) is of great importance to further improve the photovoltaic performances of organic solar cells (OSCs). PM6 and D18 are two leading wide bandgap donor polymers, but their performances are highly sensitive to the molecular weights, which have distinct impact on the morphology and thereby the charge generation and recombination processes. Here, in this work, we reported the random ternary copolymerization of PM6 and D18 segments to develop random terpolymers with finely tuned photoelectronic properties and optimized blend morphology for high-performance OSCs. The resulting random terpolymers (PMD-5, PMD-10, PMD-15 and PMD-20) exhibited finely tuned absorptions, energy levels and blend morphology. The optimal morphology of PMD-15:L8-BO contributed to the fast exciton diffusion and dissociation, efficient charge extraction with suppressed recombination. Thus, the power conversion efficiency was improved from 17.22% of the control PM6 devices and 17.47% of the control D18 devices to 18.12% of PMD-15 based devices, which is the top performance of random terpolymers. Moreover, the PMD-15 exhibited much higher batch-to-batch reproducibility at a broad molecular weight range than that of PM6 and D18, showing promising for practical applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

An optimization-based approach to tailor the mechanical response of soft metamaterials undergoing rate-dependent instabilities

An optimization-based design framework is proposed to tune the response of soft metamaterials involving both geometric instabilities and nonlinear viscoelastic material behavior. Designing the response of soft metamaterials to harness instabilities and undergo large, tailored configuration changes will enable advancements in soft robotics, shock and vibration mitigation, and flexible electronics. In line with the metamaterial concept, the response of these materials is governed to a large extent by the geometric and topological makeup of their small-scale features. However, the link between structure and response is less intuitive for soft metamaterials due to their reliance upon highly nonlinear responses triggered by geometric instabilities. This is further complicated by the effects of viscoelastic relaxation, which recent studies have shown to alter the emergence of instabilities in non-intuitive ways. Here, these effects are accounted for in our framework to achieve various design objectives, including tailored force–displacement response and maximized energy absorption from both geometric and material effects. To fully automate this process, it is essential to have a completely robust equation solver for forward problems involving instabilities and viscoelastic relaxation. We achieve this by casting the search for stable mechanical equilibrium — i.e. the forward problem — as a minimization problem and utilize a trust region algorithm to robustly handle instabilities and follow energetically-favorable equilibrium paths through critical points.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2025

Physically constrained 3D diffusion for inverse design of fiber-reinforced polymer composite materials

Designing fiber-reinforced polymer composites (FRPCs) with a tailored nonlinear stress-strain response is crucial for applications such as energy absorption in crash structures, flexible robotics, and impact-resistant protective gear. However, the inherent complexities of composite materials and the multitude of parameters involved, render traditional design and optimization methods inadequate for achieving effective inverse design of composites. In this paper, we present an AI-based inverse design framework that effectively and efficiently generates FRPCs with targeted nonlinear stress-strain responses. We introduce a physically constrained diffusion model (PC3D_Diffusion) capable of managing the complexities of composite materials and producing detailed, high-quality designs. We propose a loss-guided, learning-free approach to generate physically feasible microstructure designs by explicitly enforcing physical constraints during the generation process. For training purposes, 1.35 million FRPC samples were created, and their corresponding stress-strain curves were computed using established physics-based computational models. The results show that PC3D_Diffusion consistently generates high-quality designs with tailored mechanical behaviors, while guaranteeing compliance with the physical constraints. PC3D_Diffusion advances FRPC inverse design and may facilitate the inverse design of other 3D materials, offering potential applications in industries reliant on materials with custom mechanical properties.

Xu, Pei [Clemson Univ., SC (United States)]↗
DOE OSTI2024

Solid face sheets enable lattice metamaterials to withstand high-amplitude impulsive loading without yielding

Owing to their ability to provide tunable mechanical responses, lattice materials are frequently studied to elucidate their response to static and dynamic loads. However, these roles are typically in opposition: static loads must be supported sufficiently far away from the onset of buckling or yielding, whereas dynamic loads are typically ameliorated by crushing of the lattice, which provides excellent energy-absorption due to the large plastic deformation accompanying densification. In contrast, this work considers the octet truss as an exemplar topology, in a structural role where it must simultaneously support static loads while enduring high-amplitude impulsive loads. This study focuses on the ability to withstand impulsive loads without yielding, an essential prerequisite to enduring dual loading. Computational studies using the ALE3D hydrocode were performed to examine the response of the octet truss under a short temporal width impulse shape associated with laser-driven shocks. A key finding was that covering the lattice with a solid face sheet and treating this face sheet thickness as a design variable allows the Taylor-like pulse to be attenuated prior to entering the weaker lattice, at the cost of added mass up front. Experimental validation was accomplished by laser-driven shock testing, using octet trusses printed out of Ti-5Al-5V-5Mo-3Cr. The results show that for a given quantity of mass, the attenuation is maximized when as much mass as possible is moved into the face sheet, leaving a more slender lattice structure. The effect of placing mass in the face sheet rather than lattice beams dominates the effect of relative density, to the point where a low-mass structure with most of the mass concentrated in the face sheet can outperform a high-mass structure with most of the mass in the lattice. Finally, by further understanding the propagation of short pulse width waves within under-dense structures, this study expand the domain of applicability of such structures, including lattice materials, to challenging dual-loading regimes spanning decades of strain rates.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Performance of hybridized bamboo-carbon fiber reinforced polypropylene composites processed using wet laid technique

The end-of-life vehicles (ELV) regulations motivate hybrid materials usage in automotive industries to optimize properties at reduced cost and increase eco-friendly designs. This research explores hybrid compositions of natural bamboo fiber and synthetic carbon fiber. The goal of hybridization was to synergistically benefit from each constituent– i.e., sustainability, energy absorption and superior damping from bamboo, and high strength and stiffness from carbon fiber. Carbon fibers (CF), bamboo fibers (BF) and polypropylene (PP) fibers were dispersed in water to produce wet-laid hybrid mats. The mats were compression molded into consolidated panels to obtain the hybrid composite(s) (BF-CF-PP). Four formulations with different fiber-resin weight percent were designed and produced including- BF-PP (30/70), BF-PP (50/50), BF-CF-PP (32/8/60), and BF-CF-PP (8/32/60). The effect of (a) fiber length, (b) surface treatment, (c) fiber content, and (d) consolidation pressure on the mechanical properties were examined. The improved mechanical (flexural strength 76.4 MPa, flexural modulus 4.1 GPa, ILSS 12.4 MPa and impact strength 49.9 KJ/m 2 ) and vibrational damping (1.05%) properties showed that the BF-CF-PP (8/32/60) provided higher properties compared to the other variants. The projected properties at various stoichiometric ratios of carbon and bamboo fiber revealed that the properties of hybrid composites could be tailored to produce desirable, cost-effective, and sustainable automotive components.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Dynamic crushing of metal lattice metamaterials: Shock mode diagrams and transition to topology-independent compaction regime

Additively manufactured lattice metamaterials offer design versatility in strength and energy absorption and provide an additional degree of freedom through the selection of the lattice topology. Under quasistatic loading, the unit cell structure can strongly affect the stiffness, yield, and post-yield behavior, but whether and to what degree the effect of lattice topology persists into dynamic loading scenarios, up to the compaction shock regime, has not been established. LLNL’ s ALE3D hydrocode was used to perform a computational investigation of dynamic loading in multiple lattice types, including the gyroid, octet, Schwarz D, and rhombic dodecahedron, under impact velocities from 0.25 to 2.25 km/s. Shock Hugoniots for each lattice topology are generated and compared, suggesting that above a critical velocity, distinctions between architectures may not persevere and compacted lattices behave similarly. Here, to investigate the transition between topology-dependent quasistatic compression and the topology-independent regime above the critical velocity, a one-dimensional elastic-linear hardening plasticity-densified solid (E-LHP-DS) shock model for lattice materials was developed that relies upon confined compression to link the quasistatic and shock mechanics. Unlike similar works, the model does not assume rigid behavior prior to yield or locking behavior at densification, allowing a richer exploration of lattice mechanics. With only six parameters, the analytical model simultaneously fit quasistatic confined compression simulations for relative densities 0.1 $≤ \bar{ρ} ≤$ 0.9 and predicted dynamic compaction behavior to traverse several distinct shock modes, each defined by a critical impact speed (equivalently, critical stresses). Comparing the numerical results to the one-dimensional E-LHP-DS shock model predictions suggests that the topology-independence under strong shocks is linked to the onset of densification, which can be predicted based on quasistatic confined compression results.

Cellular material↗
DOE OSTI2022

High strain-rate compression behavior of polymeric rod and plate Kelvin lattice structures

The compressive high strain-rate behavior of polymeric Kelvin lattice structures with rod-based or plate-based unit cells was investigated through experimental techniques and finite element simulations. Polymeric lattice structures with 5x5x5 unit cell geometries were manufactured on the millimeter scale using vat polymerization additive manufacturing and tested at low (0.001/s) and high (1000/s) strain-rates. High strain-rate experiments were performed and validated for a viscoelastic split-Hopkinson (Kolsky) pressure bar system (SHPB) coupled with high-speed imaging and digital image correlation (DIC). Experimental results at both low and high strain-rates show the formation of a localized deformation band which was more prevalent in low relative density specimens and low strain-rate experiments. Strain-rate effects of lattice specimens strongly correlate with effects of the base polymer material; both bulk polymer and lattice specimen demonstrated strain-rate hardening, strain-rate stiffening, and decreased fracture strain under dynamic loading. Results show mechanical failure properties and energy absorption depended strongly on the relative density of the lattice specimen and exhibited distinct scaling between relative density and geometry type (rod, plate) and loading rate. High relative density plate-lattices demonstrated inferior mechanical properties to rod-lattices; however, there exists a critical relative density for a given mechanical property (17%- 28%) below which plate-lattices outperform rod-lattices of similar mass. As a result, high strain-rate explicit finite element simulations were performed and showed good agreement with the mechanical failure trends and deformation modes observed in the experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Evaluating Fracture Behavior of Bioinspired Alumina-YSZ Composites through Static and Dynamic Mechanical Testing

Ceramic materials are known for their high hardness and strength but are limited by low toughness and sudden failure. Inspired by the microstructure of dental enamel, which features undulating rods that promote crack deflection and energy absorption, architected specimens were designed and manufactured. A bespoke ball-on-ring (BoR) testing apparatus measured the static biaxial rupture strength of these bioinspired materials. Additionally, impact testing with spherical steel projectiles assessed their behavior under dynamic conditions. Monolithic alumina specimens were compared to architected alumina reinforced with yttria-stabilized zirconia (YSZ) rods produced via direct ink write 3D printing. BoR tests revealed that monolithic alumina had a Weibull modulus of 10.53 and a characteristic strength of 372.3 MPa, while the composite specimens showed a Weibull modulus of 5.46 and a characteristic strength of 213.3 MPa. Although the composite failed at lower stresses and projectile velocities, it exhibited notable crack deflection and fracture resistance, with cracks being effectively interrupted by the rod inclusions. The composite specimens also resulted in fewer and larger fragments upon impact. Finite element simulations confirmed the effectiveness of the rod structures in enhancing fracture resistance.

Bioinspired materials↗
DOE OSTI2020

Toughening by Nanodroplets: Polymer–Droplet Biocomposite with Anomalous Toughness

The development of new polymer composites is highly dependent on the design of novel fillers that can bring more benefits in the design and control of structure–property–function than conventional solid particles. Here, inspired by the unique coupling structures of tough mussel byssus, we employ nanodroplets of high-boiling-point oligomers as the liquid filler to fabricate a new class of polymer–droplet composites (PDCs). The combination of nanodroplets and chain end/tail modifier in PDCs finally generates soft-coupling structures with chain ends coupled by the nanodroplets. With this strategy, brittle poly(lactic acid) is successfully transformed into a tough bioplastic with toughness improved by over 2000% via a minimal amount of the modifiers (1.5 wt %). Moreover, the composites show unexpected speed-enhanced energy absorption capability. A soft-coupling toughening mechanism is further proposed for the first time to understand the PDCs’ mechanical properties. This work also indicates the potential of nanodroplets as a new tool for tuning the mechanical properties and even functions of polymer composites.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Adapting the Electron Beam from SEM as a Quantitative Heating Source for Nanoscale Thermal Metrology

The electron beam (e-beam) in the scanning electron microscopy (SEM) provides an appealing mobile heating source for thermal metrology with spatial resolution of ~1 nm, but the lack of systematic quantification of the e-beam heating power limits such application development. Here, we systemically study e-beam heating in LPCVD silicon nitride (SiN x ) thin-films with thickness ranging from 200 to 500 nm from both experiments and complementary Monte Carlo simulations using the CASINO software package. There is good agreement about the thickness-dependent e-beam energy absorption of thin-film between modeling predictions and experiments. Using the absorption results, we then demonstrate adapting the e-beam as a quantitative heating source by measuring the thickness-dependent thermal conductivity of SiN x thin-films, with the results validated to within 7% by a separate Joule heating experiment. The results described here will open a new avenue for using SEM e-beams as a mobile heating source for advanced nanoscale thermal metrology development.

42 ENGINEERING↗
DOE OSTI2024

Mechanochemically responsive polymer enables shockwave visualization

Abstract Understanding the physical and chemical response of materials to impulsive deformation is crucial for applications ranging from soft robotic locomotion to space exploration to seismology. However, investigating material properties at extreme strain rates remains challenging due to temporal and spatial resolution limitations. Combining high-strain-rate testing with mechanochemistry encodes the molecular-level deformation within the material itself, thus enabling the direct quantification of the material response. Here, we demonstrate a mechanophore-functionalized block copolymer that self-reports energy dissipation mechanisms, such as bond rupture and acoustic wave dissipation, in response to high-strain-rate impacts. A microprojectile accelerated towards the polymer permanently deforms the material at a shallow depth. At intersonic velocities, the polymer reports significant subsurface energy absorption due to shockwave attenuation, a mechanism traditionally considered negligible compared to plasticity and not well explored in polymers. The acoustic wave velocity of the material is directly recovered from the mechanochemically-activated subsurface volume recorded in the material, which is validated by simulations, theory, and acoustic measurements. This integration of mechanochemistry with microballistic testing enables characterization of high-strain-rate mechanical properties and elucidates important insights applicable to nanomaterials, particle-reinforced composites, and biocompatible polymers.

Science & Technology - Other Topics↗
DOE OSTI2025

Moiré-controllable exciton localization and dynamics through spatially-modulated inter- and intralayer excitons in a MoSe 2 /WS 2 heterobilayer

Moiré heterobilayers exhibiting spatially varying exciton localization that can be precisely controlled through the twist angle have emerged as exciting platforms for studying complex quantum phenomena. Here, we study the exciton landscape in MoSe 2 /WS 2 heterobilayers through synergistic first-principles GW plus Bethe Salpeter equation (GW-BSE) calculations and complementary time- and angle-resolved photoemission spectroscopy (tr-ARPES). We find that the MoSe 2 /WS 2 heterobilayer has a type I band alignment at large twist angles. In contrast, at small twist angles, there exist simultaneous spatially modulated regions of local type I band alignment, hosting bright intralayer excitons, and local type II band alignment, hosting long-lived interlayer excitons, due to lattice reconstruction in different high-symmetry regions. In tr-ARPES this manifests in the observation of long-lived excitons with electron population in only MoSe 2 at large twist angles, while in samples with small twist angles, signals from two distinct long-lived exciton states with electron population in both layers are observed. Contrary to earlier studies, we find no excitonic hybridization near the low-energy absorption peaks in MoSe 2 /WS 2 , whose splitting can, instead, be explained by the lattice reconstruction.

Electronic properties and materials↗