Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Embedding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Effect of Embedded Piezoelectric Sensors on Fracture Toughness and Fatigue Resistance of Composite Laminates Under Mode I Loading

Double-cantilevered beam (DCB) specimens of a glass/epoxy composite material with embedded piezoelectric sensors were tested both statically and under fatigue loading to determine the effect of the embedded material on the Mode I fracture toughness and fatigue resistance compared to baseline data without the embedded elements. A material known as LaRC-Macrofiber Composite (LaRC-MFC (TradeMark)), or MFC, was embedded at the midplane of the specimen during the layup. Specimens were manufactured with the embedded MFC material either at the loaded end of the specimen to simulate an initial delamination; or with the MFC material located at the delaminating interface, with a Teflon film at the loaded end to simulate an initial delamination. There were three types of specimens with the embedded material at the delaminating interface: co-cured with no added adhesive; cured with a paste adhesive applied to the embedded element; or cured with a film adhesive added to the embedded material. Tests were conducted with the sensors in both the passive and active states. Results were compared to baseline data for the same material without embedded elements. Interlaminar fracture toughness values (G(sub Ic)) for the passive condition showed little change when the MFC was at the insert end. Passive results varied when the MFC was at the delaminating interface. For the co-cured case and with the paste adhesive, G(sub Ic) decreased compared to the baseline toughness, whereas, for the film adhesive case, G(sub Ic) was significantly greater than the baseline toughness, but the failure was always catastrophic. When the MFC was in the active state, G(sub Ic) was generally lower compared to the passive results. Fatigue tests showed little effect of the embedded material whether it was active or passive compared to baseline values.

Murri, Gretchen B.↗

EFFECT OF INCLINED WAVES ON DEEPLY EMBEDDED NUCLEAR FACILITIES

Several conceptual designs for advanced reactors show that most if not all of the structure is embedded in the soil. Consequently, analysis techniques that have been verified and validated for the analysis of light water reactors on surface foundations may not be directly applicable to deeply embedded reactors. Specifically two effects that may change the in-structure response (ISR) of embedded facilities are: (i) the effect of the kinematic interaction becomes more prominent as the embedment depth increases; (ii) non-vertically propagating waves, which are usually not considered for surface-founded facilities, may be more important for deeply embedded facilities. A preliminary study is presented in this article to understand the response of embedded nuclear facilities to non-vertically propagating seismic waves. The inclined wave field is generated from source-to-site simulations using representative earthquake faults with different dip angles. The embedment depth of the nuclear containment facility is also varied to obtain a better understanding of the effect of embedment. This analysis of the soil-structure ensemble is conducted using the application called Multi-hazard Analysis for STOchastic time-DOmaiN phenomena (MASTODON), developed on top of Idaho National Lab’s open source MOOSE finite element framework. The Domain Reduction Method implemented in MASTODON to incorporate the seismic excitation within the region of interest is verified and then used to reduce the computational effort in analyzing this problem. Preliminary analysis using linear soil and structure material properties and tied contact between the soil and structure indicate that embedding the nuclear facility reduces significantly the response of the structure in all the earthquake scenarios considered.

42 ENGINEERING↗

Learning Canonical Embeddings for Unsupervised Shape Correspondence With Locally Linear Transformations

We present a new approach to unsupervised shape correspondence learning between pairs of point clouds. We make the first attempt to adapt the classical locally linear embedding algorithm (LLE)-originally designed for nonlinear dimensionality reduction-for shape correspondence. The key idea is to find dense correspondences between shapes by first obtaining high-dimensional neighborhood-preserving embeddings of low-dimensional point clouds and subsequently aligning the source and target embeddings using locally linear transformations. We demonstrate that learning the embedding using a new LLE-inspired point cloud reconstruction objective results in accurate shape correspondences. More specifically, the approach comprises an end-to-end learnable framework of extracting high-dimensional neighborhood-preserving embeddings, estimating locally linear transformations in the embedding space, and reconstructing shapes via divergence measure-based alignment of probability density functions built over reconstructed and target shapes. Our approach enforces embeddings of shapes in correspondence to lie in the same universal/canonical embedding space, which eventually helps regularize the learning process and leads to a simple nearest neighbors approach between shape embeddings for finding reliable correspondences. Comprehensive experiments show that the new method makes noticeable improvements over state-of-the-art approaches on standard shape correspondence benchmark datasets covering both human and nonhuman shapes.

deformation↗

Parallel Embeddings: a Visualization Technique for Contrasting Learned Representations

We introduce ``Parallel Embeddings'', a new technique that generalizes the classical Parallel Coordinates visualization technique from a sequence of features within a single matrix to a sequence of multiple feature matrices. This is accomplished by separately embedding each matrix in the sequence into a 2-D frame, juxtaposing these 2-D representations, then connecting points between frames. We outline how this visualization can be used for several ``model comparison'' tasks in machine learning. We compare user performance with Parallel Embeddings to a baseline using the TensorFlow Embedding Projector for estimating model accuracy and understanding conceptual model differences. We found that users were more accurate with Parallel Embeddings for model comparison and that users learned how to use Parallel Embeddings more quickly than TensorFlow Embedding Projector. Furthermore, users' analytical process using Embedding Projector was positively affected by using Parallel Embeddings beforehand.

Model comparison, machine learing, machine learnin↗

Performance of Embedded Sensors in 3D Printed SiC

This report summarizes recent advances in embedding sensors in 3D printed silicon carbide (SiC) ceramic components under the Transformational Challenge Reactor (TCR) program. The additive manufacturing technologies developed under this program will enable fabrication of complex structures with embedded fuels and sensors. The sensors will be capable of characterizing fuel performance using spatially distributed measurements at the most strategic locations that would be otherwise inaccessible using conventional manufacturing techniques. While previous programmatic updates describe initial concepts for embedding sensors, materials selection, and initial characterization of the embedded sensors, the technology requires further demonstration, and quality-significant procedures must be established before the embedding technology is ready for adoption by industry. To this end, this report describes the most effective techniques that have been used to embed functional sensors in 3D printed components using a combination of binder-jet additive manufacturing and chemical vapor infiltration (CVI). A detailed procedure describes each step in the process and is available upon request. Molybdenum (Mo)-sheathed thermocouples have been successfully embedded in complex SiC components, and temperatures were monitored in situ during the embedding process. Post-embedding measurements showed no significant hysteresis, and characterization of the interface revealed qualitatively strong bonding around the entire perimeter of the sensor sheath. Distributed fiber-optic temperature sensors were able to briefly measure temperature profiles during CVI, but they ultimately failed prior to completion of the CVI run. The failure appears to be related to the fiber coating at temperatures close to 1,000°C. Future work will focus on irradiation testing of embedded thermocouples and other sheathed electrical sensors, as well as the identification of fiber-optic sensor coatings that can survive CVI.

42 ENGINEERING↗

Laser-assisted embedding of all-glass optical fiber sensors into bulk ceramics for high-temperature applications

We develop a laser-assisted sensor embedding process to embed all-glass optical fiber sensors into bulk ceramics for high-temperature applications. A specially designed two-step microchannel was fabricated on an Al 2 O 3 substrate for sensor embedment using a picosecond (ps) laser. An optical fiber Intrinsic Fabry-Perot Interferometer (IFPI) sensor was embedded at the bottom of the microchannel and covered by Al 2 O 3 slurry which was subsequently sintered by a CO 2 laser. The sensor spectrum was in-situ monitored during the laser sintering process to ensure the survival of the sensor and optimize the laser sintering parameters. By testing in furnace through high temperature, the embedded optical fiber shows improved stability after CO 2 laser sealing, resulting in the linear temperature response of the embedded optical fiber IFPI sensor. To improve the embedded IFPI sensor for thermal strain measurement, a dummy fiber was co-embedded with the sensing fiber to improve the mechanical bonding between the sensing fiber and the ceramic substrate so that the thermal strain of the ceramic substrate can apply on the sensing fiber. The response sensitivity, measurement repeatability and high-temperature long-term stability of the embedded optical fiber IFPI sensor were evaluated in this work.

47 OTHER INSTRUMENTATION↗

4-Clique network minor embedding for quantum annealers

Quantum annealing is a quantum algorithm for computing solutions to combinatorial optimization problems. This study proposes a method for minor embedding optimization problems onto sparse quantum annealing hardware graphs called 4-clique network minor embedding. This method is in contrast to the standard minor embedding technique of using a path of linearly connected qubits in order to represent a logical variable state. The 4-clique minor embedding is possible on Pegasus graph connectivity, which is the native hardware graph for some of the current D-Wave quantum annealers. The Pegasus hardware graph contains many cliques of size 4, making it possible to form a graph composed entirely of paths of connected 4-cliques on which a problem can be minor-embedded. The 4-clique chains come at the cost of additional qubit usage on the hardware graph, but they allow for stronger coupling within each chain, thereby increasing chain integrity, reducing chain breaks, and allow for greater usage of the available energy scale for programming logical problem coefficients on current quantum annealers. The 4-clique minor embedding technique is compared with the standard linear path minor embedding with experiments on two D-Wave quantum annealing processors with Pegasus hardware graphs. We show proof-of-concept experiments where the 4-clique minor embeddings can use weak chain strengths while successfully carrying out the computation of minimizing random all-to-all spin glass problem instances. Published by the American Physical Society 2024

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Molecular interactions with ice: Molecular embedding, adsorption, detection, and release

The interaction of atomic and molecular species with water and ice is of fundamental importance for chemistry. In a previous series of publications, we demonstrated that translational energy activates the embedding of Xe and Kr atoms in the near surface region of ice surfaces. In this paper, we show that inert molecular species may be absorbed in a similar fashion. We also revisit Xe embedding, and further probe the nature of the absorption into the selvedge. CF{sub 4} molecules with high translational energies (≥3 eV) were observed to embed in amorphous solid water. Just as with Xe, the initial adsorption rate is strongly activated by translational energy, but the CF{sub 4} embedding probability is much less than for Xe. In addition, a larger molecule, SF{sub 6}, did not embed at the same translational energies that both CF{sub 4} and Xe embedded. The embedding rate for a given energy thus goes in the order Xe > CF{sub 4} > SF{sub 6}. We do not have as much data for Kr, but it appears to have a rate that is between that of Xe and CF{sub 4}. Tentatively, this order suggests that for Xe and CF{sub 4}, which have similar van der Waals radii, the momentum is the key factor in determining whether the incident atom or molecule can penetrate deeply enough below the surface to embed. The more massive SF{sub 6} molecule also has a larger van der Waals radius, which appears to prevent it from stably embedding in the selvedge. We also determined that the maximum depth of embedding is less than the equivalent of four layers of hexagonal ice, while some of the atoms just below the ice surface can escape before ice desorption begins. These results show that energetic ballistic embedding in ice is a general phenomenon, and represents a significant new channel by which incident species can be trapped under conditions where they would otherwise not be bound stably as surface adsorbates. These findings have implications for many fields including environmental science, trace gas collection and release, and the chemical composition of astrophysical icy bodies in space.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Bootstrap embedding: An internally consistent fragment-based method

Strong correlation poses a difficult problem for electronic structure theory, with computational cost scaling quickly with system size. Fragment embedding is an attractive approach to this problem. By dividing a large complicated system into smaller manageable fragments “embedded” in an approximate description of the rest of the system, we can hope to ameliorate the steep cost of correlated calculations. While appealing, these methods often converge slowly with fragment size because of small errors at the boundary between fragment and bath. We describe a new electronic embedding method, dubbed “Bootstrap Embedding,” a self-consistent wavefunction-in-wavefunction embedding theory that uses overlapping fragments to improve the description of fragment edges. We apply this method to the one dimensional Hubbard model and a translationally asymmetric variant, and find that it performs very well for energies and populations. We find Bootstrap Embedding converges rapidly with embedded fragment size, overcoming the surface-area-to-volume-ratio error typical of many embedding methods. We anticipate that this method may lead to a low-scaling, high accuracy treatment of electron correlation in large molecular systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Demonstrate embedding of sensors in a relevant microreactor component

This report describes the first successful embedding of sensors in stainless steel pipe specimens and a miniature hex block to support structural health monitoring of microreactor components during electrically heated testing in non-nuclear testbed facilities. Sensors were embedded with an ultrasonic additive manufacturing process that uses a combination of downward pressure and an ultrasonic scrubbing motion to bond stainless steel foils to underlying materials. After placing sensors within cavities that have been machined to the size of the sensors, the ultrasonic bonding process fills the gaps around the sensors and embeds them within the part. Both Type K thermocouples and spatially distributed fiber-optic strain sensors were successfully embedded within two pipe specimens and a miniature hex block. After the fiber-optic sensors were embedded, they were interrogated and found to have minimal signal attenuation within the embedded region—a significant improvement compared to previous trials. This is likely because of the low-bend-loss fiber that was used, which greatly reduces microbending losses that occur after the embedding process. In addition to showing minimal signal attention, the fibers also showed adequate compressive strain, which is a strong indication that the sensors are physically embedded in the parts as opposed to simply being loosely contained inside the machined cavities. The embedded fibers were able to capture the strain induced in one of the pipe specimens while the pipe was actively heated with a moving heat source.

42 ENGINEERING↗

Characterization of Embedded Sensors in Stainless Steel Test Articles and Design/Planning for MAGNET Testing

The nuclear industry is pursuing microreactors that can be factory assembled and deployed to remote regions for reliable power generation. One class of microreactors uses a monolithic metal core block coupled to heat pipes for heat rejection, which results in significant thermal stresses in the monolithic structures. This work describes the initial characterization and test plan for evaluating stainless steel test articles fabricated with embedded sensors for measuring heat pipe performance limits, as well as spatially distributed temperatures and strains during electrically heated thermal testing. The electrically heated testing will be performed in the non-nuclear Microreactor Agile Non-Nuclear Testbed and Single Primary Heat Extraction and Removal Emulator facilities located at Idaho National Laboratory. The goals of these tests are to (1) accurately monitor temperature and strain distributions that result from differential thermal expansion in the test articles and (2) quantify heat rejection limits of heat pipes as a function of operating temperature and working fluid during steady-state and transient operations. More generally, the ability to monitor component and system health during microreactor operation is attractive for providing a high sensor density to inform a limited number of microreactor operators to ultimately reduce operation and maintenance costs and move toward semi-autonomous operation. This report discusses the characterization of embedded thermocouples and fiber optic sensors in relevant test articles, including cylindrical pipes and hexagonal monolithic test articles for heat pipe-based reactors. The sensors were embedded by placing them in machined channels and then building up additional material by using ultrasonic additive manufacturing (UAM). UAM is a solid-state welding process that uses downward pressure and a lateral scrubbing motion to bond thin metal foils to a base material layer by layer. The ultrasonic welding process relies on the plastic deformation of the metal—as opposed to typical melting and solidification—to break oxide scales and bond the metal layers. The characterization of these embedded sensors included evaluating fiber optic signal attenuation, observing residual strain in the fibers, investigating microstructural and mechanical aspects, and demonstrating the sensors under various thermal loads and acoustic vibrations. Post-embedding characterization showed a fine grain structure (<1 μm) near the interfaces of the bonded foils as a result of severe deformation from the welding process. A large increase in hardness was observed at the foil interfaces and the fiber/matrix interface compared with the bulk matrix. Even when compared with the SS304 interfaces, the higher hardness observed around the embedded fiber suggests a higher degree of deformation due to the soft metal coating around the silica fiber core. The distributed fiber-optic temperature sensors and embedded thermocouples reliably measured temperature distributions during steady-state and transient thermal testing. The embedded fiber-optic sensors reliably measured strain during both transient and steady-state testing and properly identified resonant frequencies during acoustic testing.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Embedded arrays of vertically aligned carbon nanotube carpets and methods for making them

According to some embodiments, the present invention provides a system and method for supporting a carbon nanotube array that involve an entangled carbon nanotube mat integral with the array, where the mat is embedded in an embedding material. The embedding material may be depositable on a carbon nanotube. A depositable material may be metallic or nonmetallic. The embedding material may be an adhesive material. The adhesive material may optionally be mixed with a metal powder. The embedding material may be supported by a substrate or self-supportive. The embedding material may be conductive or nonconductive. The system and method provide superior mechanical and, when applicable, electrical, contact between the carbon nanotubes in the array and the embedding material. The optional use of a conductive material for the embedding material provides a mechanism useful for integration of carbon nanotube arrays into electronic devices.

36 MATERIALS SCIENCE↗

An improved hyperbolic embedding algorithm

Because hyperbolic space has properties that make it amenable to graph representations, there is significant interest in scalable hyperbolic-space embedding methods. These embeddings enable constant-time approximation of shortest-path distances, and so are significantly more efficient than full shortest-path computations. In this article, we improve on existing landmark-based hyperbolic embedding algorithms for large-scale graphs. Whereas previous methods compute the embedding by using the derivative-free Nelder–Mead simplex optimization method, our approach uses the limited-memory BFGS (LBFGS) method, which is quasi-Newton optimization, with analytic gradients. Our method is not only significantly faster but also produces higher-quality embeddings. Moreover, we are able to include the hyperbolic curvature as a variable in the optimization. We compare our hyperbolic embedding method implementation in Python (called Hypy) against the best publicly available software, Rigel. Our method is an order of magnitude faster and shows significant improvements in the accuracy of the shortest-path distance calculations. Furthermore, tests are performed on a variety of real-world networks, and we show the scalability of our method by embedding a graph with 1.8 billion edges and 65 million nodes.

97 MATHEMATICS AND COMPUTING↗

Efficiently embedding QUBO problems on adiabatic quantum computers

Adiabatic quantum computers like the D-Wave 2000Q can approximately solve the QUBO problem, which is an NP-hard problem, and have been shown to outperform classical computers on several instances. Solving the QUBO problem literally means solving virtually any NP-hard problem like the traveling salesman problem, airline scheduling problem, protein folding problem, genotype imputation problem, thereby enabling significant scientific progress, and potentially saving millions/billions of dollars in logistics, airlines, healthcare and many other industries. Yet, before QUBO problems are solved on quantum computers, they must be embedded (or compiled) onto the hardware of quantum computers, which in itself is a very hard problem. Here, we propose an efficient embedding algorithm, that lets us embed QUBO problems fast, uses less qubits and gets the objective function value close to the global minimum value. We then compare the performance of our embedding algorithm to that of D-Wave’s embedding algorithm, which is the current state of the art, and show that our embedding algorithm convincingly outperforms D-Wave’s embedding algorithm. Our embedding approach works with perfect Chimera graphs, i.e., Chimera graphs with no missing qubits.

97 MATHEMATICS AND COMPUTING↗

Advanced ceramic components with embedded sapphire optical fiber sensors for high temperature applications

Here this paper describes an extrusion-based additive manufacturing process that has been developed to enable embedment of sapphire optical fiber sensors in ceramic components during the part fabrication. In this process, an aqueous paste of ceramic particles is extruded through a moving nozzle to build the part layer-by-layer. In the case of sensor embedment, the fabrication process is halted after a certain number of layers have been deposited; the sensors are placed in their predetermined locations, and the remaining layers are deposited until the part fabrication is completed. Because the sensors are embedded during the fabrication process, they are fully integrated with the part and the problems of traditional sensor embedment can be eliminated. Scanning electron microscopy was used to observe the embedded sensors and to detect any possible flaws in the part or embedded sensor. Attenuation of the sensors was measured in near-infrared region (1500–1600 nm wavelength). Standard test methods were employed to examine the effect of embedded fibers on the strength and hardness of the parts. The results indicated that the sapphire fiber sensors with diameters smaller than 250 micrometers were able to endure the freeform extrusion fabrication process and the post-processing without compromising the part properties.

36 MATERIALS SCIENCE↗

Reforming sewage sludge pyrolysis volatile with Fe-embedded char: Minimization of liquid product yield

Highlights: • Fe{sub 2}(SO{sub 4}){sub 3} is added in sewage sludge to produce pyrolysis char (SSC) embedded with Fe. • Fe-embedded SSC is utilized to reform the same source volatile to produce high quality syngas and avoid liquid products. • More gas is produced with raised H{sub 2} content as Fe concentration elevated in the Fe-embedded SSC. • Total liquid product and its oily fraction decreased greatly after reformed with Fe-embedded SSC. - Abstract: Obtaining high quality syngas from sewage sludge (SS) means transferring a low-grade SS into a high-grade fuel or raw materials for chemical products. In this study, Fe is added to SS in form of Fe{sub 2}(SO{sub 4}){sub 3} to produce an effective and self-sufficient catalyst in order to obtain more syngas and minimize liquid products from SS pyrolysis. The Fe-embedded sewage sludge chars (SSCs) were used as catalysts for volatile reforming at 600 °C. It has been found that the gas yield increases from 15.9 to 35.8 wt% of the SS and that of liquids decreases from 31.9 to 10.2 wt% after volatile reforming with Fe-embedded SSC when Fe was added equal to 7 % in the dried SS. In addition, the content of nitrogen-containing compounds in the oily products decreased. After reforming with Fe-embedded SSC, the molar fractions of syngas combustible components, including H{sub 2}, CH{sub 4} and CO, increase, and the higher heating value of the syngas increased to 17.0 MJ/Nm{sup 3} from the original 12.5 MJ/Nm{sup 3} obtained from SS pyrolysis at 550 °C. Moreover, the volatile reforming seems to reduce the level of some important syngas pollutants, like H{sub 2}S, HCl and HCN, even though it was also observed an increase of the contents of SO{sub 2}, NH{sub 3}, NO{sub 2,} HCNO and N{sub 2}O.

09 BIOMASS FUELS↗

Mixed Delay/Nondelay Embeddings Based Neuromorphic Computing with Patterned Nanomagnet Arrays

Patterned nanomagnet arrays (PNAs) have been shown to exhibit a strong geometrically frustrated dipole interaction. Some PNAs have also shown emergent domain wall dynamics. Previous works have demonstrated methods to physically probe these magnetization dynamics of PNAs to realize neuromorphic reservoir systems that exhibit chaotic dynamical behavior and high-dimensional nonlinearity. These PNA reservoir systems from prior works leverage echo state properties and linear/nonlinear short-term memory of component reservoir nodes to map and preserve the dynamical information of the input time-series data into nondelay spatial embeddings. Such mappings enable these PNA reservoir systems to imitate and predict/forecast the input time series data. However, these prior PNA reservoir systems are based solely on the nondelay spatial embeddings obtained at component reservoir nodes. As a result, they require a massive number of component reservoir nodes, or a very large spatial embedding (i.e., high-dimensional spatial embedding) per reservoir node, or both, to achieve acceptable imitation and prediction accuracy. These requirements reduce the practical feasibility of such PNA reservoir systems. To address this shortcoming, we present a mixed delay/nondelay embeddings-based PNA reservoir system. Our system uses a single PNA reservoir node with the ability to obtain a mixture of delay/nondelay embeddings of the dynamical information of the time-series data applied at the input of a single PNA reservoir node. Our analysis shows that when these mixed delay/nondelay embeddings are used to train a perceptron at the output layer, our reservoir system outperforms existing PNA-based reservoir systems for the imitation of NARMA 2, NARMA 5, NARMA 7, and NARMA 10 time series data, and for the short-term and long-term prediction of the Mackey Glass time series data.

Ti, Changpeng↗

Computationally Efficient Learning of Quality Controlled Word Embeddings for Natural Language Processing

Deep learning (DL) has been used for many natural language processing (NLP) tasks due to its superior performance as compared to traditional machine learning approaches. In DL models for NLP, words are represented using word embeddings, which capture both semantic and syntactic information in text. However, 90-95% of the DL trainable parameters are associated with the word embeddings, resulting in a large storage or memory footprint. Therefore, reducing the number of word embedding parameters is critical, especially with the increase of vocabulary size. In this work, we propose a novel approximate word embeddings approach for convolutional neural networks (CNNs) used for text classification tasks. The proposed approach significantly reduces the number of model trainable parameters without noticeably sacrificing in computing performance accuracy. Compared to other techniques, our proposed word embeddings technique does not require modifications to the DL model architecture. We evaluate the performance of the the proposed word embeddings on three classification tasks using two datasets, composed of Yelp and Amazon reviews. The results show that the proposed method can reduce the number of word embeddings parameters by 98% and 99% for the Yelp and Amazon datasets respectively, with no drop in computing accuracy.

Alawad, Mohammed↗