Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EROSION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Studies on Enhancement of Silt Erosion Resistance of 13/4 Martensitic Stainless Steel by Low-Temperature Salt Bath Nitriding

Low-temperature salt bath nitriding of heat treated and tempered 13/4 Martensitic stainless steel (13/4HTT) was carried at 450 °C (N450) and 500 °C (N500) for 10 h each. The nitrided samples were characterized by using x-ray diffractometer, field emission scanning electron microscope and optical microscope. The nanohardness and elastic modulus of the cross section of nitrided specimen were measured by nanoindentation test using Hysitron TI950 triboindenter. The nitrided 13/4HTT (N450 and N500) and 13/4HTT specimens were subjected to slurry erosion test in a slurry pot tester. The test was conducted for 48 h, and weight loss was measured after every 6 h. The relative speed of slurry with respect to specimen was 4.55 m/s. It was found that the weight loss due to erosion of the N450 is 83% less than that of 13/4HTT and that of N500 was 92% more than that of 13/4HTT. The erosion mechanism is correlated to the phases present in the specimens. The improvement in the slurry erosion resistance of N450 is due to presence of expanded martensite (α{sub N}-Fe). Increasing the temperature of nitriding to 500 °C led to the decrease in the slurry erosion resistance of N500 due to the formation of brittle CrN phase.

36 MATERIALS SCIENCE↗

Effect of Microstructure and Properties of Ni-WC Composite Coatings on Their Solid Particle Erosion Behavior

Metal matrix composites (MMCs) of WC in Co or Ni matrices are widely used due to their high wear resistance. Previous studies showed that tailoring the mechanical properties through optimum WC content can significantly extend the life cycle of MMCs. In this study, composite coatings of Ni with various WC content ranging from 10 to 55 vol.% were cold sprayed using agglomerated WCNi powders and two different sizes of Ni powders, − 10 + 4 (d{sub 50} = 7 µm) referred to as Ni(7) and − 35 + 15 (d{sub 50} = 25 µm) to as Ni(25). Microstructural characterization, including the deformed structure of Ni splats and retention and distribution of WC, was performed by scanning electron microscopy (SEM). Composite coatings were subjected to solid particle erosion following ASTM G76-13 standard. At low WC content coatings, erosion occurred primarily by plastic deformation of Ni matrices and knocking out of WC particles. At high WC concentrations, network distribution of compacted WCNi particles in the matrices led to a significant drop in erosion rates of coatings, due to a change in erosion mechanism from severe cutting and plowing of Ni and WC dislodging to WCNi splats spalling. Composite coatings sprayed using finer size Ni powder were usually more erosion resistant.

36 MATERIALS SCIENCE↗

Modelling soil erosion in a Mediterranean watershed: Comparison between SWAT and AnnAGNPS models

Highlights: • Outputs, input data and time requirements are compared for SWAT and AnnAGNPS. • Models are assessed also in wet and dry seasons. • Most of the basin is under moderate or high risk of erosion. • SWAT and AnnAGNPS are compared with RUSLE2015 and PESERA. In this study, the simulations generated by two of the most widely used hydrological basin-scale models, the Annualized Agricultural Non-Point Source (AnnAGNPS) and the Soil and Water Assessment Tool (SWAT), were compared in a Mediterranean watershed, the Carapelle (Apulia, Southern Italy). Input data requirements, time and efforts needed for input preparation, strength and weakness points of each model, ease of use and limitations were evaluated in order to give information to users. Models were calibrated and validated at monthly time scale for hydrology and sediment load using a four year period of observations (streamflow and suspended sediment concentrations). In the driest year, the specific sediment load measured at the outlet was 0.89 t ha{sup −1} yr{sup −1}, while the simulated values were 0.83 t ha{sup −1} yr{sup −1} and 1.99 t ha{sup −1} yr{sup −1} for SWAT and AnnAGNPS, respectively. In the wettest year, the specific measured sediment load was 7.45 t ha{sup −1} yr{sup −1}, and the simulated values were 8.27 t ha{sup −1} yr{sup −1} and 6.23 t ha{sup −1} yr{sup −1} for SWAT and AnnAGNPS, respectively. Both models showed from fair to a very good correlation between observed and simulated streamflow and satisfactory for sediment load. Results showed that most of the basin is under moderate (1.4–10 t ha{sup −1} yr{sup −1}) and high-risk erosion (> 10 t ha{sup −1} yr{sup −1}). The sediment yield predicted by the SWAT and AnnAGNPS models were compared with estimates of soil erosion simulated by models for Europe (PESERA and RUSLE2015). The average gross erosion estimated by the RUSLE2015 model (12.5 t ha{sup −1} yr{sup −1}) resulted comparable with the average specific sediment yield estimated by SWAT (8.8 t ha{sup −1} yr{sup −1}) and AnnAGNPS (5.6 t ha{sup −1} yr{sup −1}), while it was found that the average soil erosion estimated by PESERA is lower than the other estimates (1.2 t ha{sup −1} yr{sup −1}).

54 ENVIRONMENTAL SCIENCES↗

Surface Erosion of Plasma-Facing Materials Using an Electrothermal Plasma Source and Ion Beam Micro-Trenches

Erosion characteristics of tungsten-alternative plasma-facing materials (PFMs) were tested under high heat flux conditions in the electrothermal plasma source facility at Oak Ridge National Laboratory. The PFMs of interest are high-purity β-3C chemical vapor deposition silicon carbide (SiC) and the MAX phases Ti 3 SiC 2 and Ti 2 AlC [MAX = chemical formula M n+1 AX n , where M is an early transition metal (such as Ti or Ta), A is an A-group element (such as Si or Al), and X is carbon or nitrogen]. Additionally, an erosion analysis method was developed using a combination of focused ion beam microscopy and scanning electron microscopy, carving micro-trench geometries into polished sample surfaces. Samples of SiC, Ti 3 SiC 2 , and Ti 2 AlC were exposed to the electrothermal plasma source alongside tungsten and monocrystalline silicon. Samples were exposed to a Lexan polycarbonate (C 16 H 14 O 3 ) electrothermal plasma stream in a He environment, at a specified impact angle, with infrared camera diagnostics. Edge localized mode–relevant heat fluxes of 0.9 to 1 GW/m 2 over 1-ms discharges were generated on the target surfaces. Tungsten samples exhibited pronounced melt-layer formation and deformation, with measured molten pits 2 to 10 μm in diameter and melt-layer depths of up to 7 μm deep. Surface erosion rates for Ti 3 SiC 2 and Ti 2 AlC ranged from 80 to 775 μm/s and 85 to 470 μm/s, respectively. Both MAX phases exhibited extreme surface fracture and material ejection, with damage depths past 4 μm for Ti 2 AlC and 11 μm for Ti 3 SiC 2 . Lastly, SiC displayed the best performance, in one case surviving 15 consecutive electrothermal plasma exposures with an average erosion rate of about 29 μm/s and no surface fracturing. SiC erosion rates ranged from 23 to 128 μm/s.

36 MATERIALS SCIENCE↗

Advances in neutral tungsten ultraviolet spectroscopy for the potential benefit to gross erosion diagnosis

A spectral survey of tungsten emission in the ultraviolet region has been completed in the DIII-D tokamak and the CTH torsatron to assess the potential benefit of UV emission for the diagnosis of gross W erosion. Here, a total of 29 W I spectral lines are observed from the two experiments using survey spectrometers between 200 and 400 nm with level identifications provided based on a structure calculation for many of the excited states that produce strong emission lines. Of the 29 observed lines, 20 have not previously been reported in fusion relevant plasmas, including an intense line at 265.65 nm which could be important for benchmarking the frequently exploited line at 400.88 nm. Nearly all of the observed spectral lines decay down to one of the six lowest energy levels for neutral W, which are likely to be long-lived metastable states. The impact of metastable level populations on the W I emission spectrum and any erosion measurement utilizing a spectroscopic technique is potentially significant. Yet, the high density of W I emission in the UV region allows for the possibly of determining the relative metastable fractions and plasma parameters local to the erosion region. Additionally, the lines observed in this work could be used to perform multiple independent gross erosion measurements, leading to more accurate diagnosis of gross tungsten erosion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Reduced model of high-Z impurity redeposition and erosion in tokamak divertor and its application to DIII-D experiments

A reduced model of high-Z impurities erosion and redeposition is presented to analyze net erosion of tungsten material in divertor attached plasma conditions measured in DIII-D experiments. This reduced model is tailored to quantify the redeposition and the net erosion on high-Z material samples of sufficiently small dimensions to be considered exposed to uniform plasma conditions. For those uniform plasma conditions, the spatial distribution of redeposited high-Z impurities is well approximated by an analytical distribution characterized by a few parameters. The fraction of high-Z impurity eroding and redepositing on a material sample is then obtained by integrating this distribution across the material sample. Here, the ratio of net erosion rates of tungsten measured experimentally from tungsten samples of different sizes exposed to the same attached plasma conditions are well reproduced with this reduced model. It is shown that uncertainties induced by radially non-uniform plasma conditions in experiments can be significantly reduced by exposing samples to high density divertor plasma. Several enhanced experimental setups are proposed to measure and compare net erosion rates from samples of various areas during a single plasma experiment.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Predicting tungsten erosion and leakage properties for the new V-shaped small angle slot divertor in DIII-D

Impurity transport modeling of the new tungsten (W)-coated, V-shaped small angle slot (SAS) divertor in the DIII-D tokamak was conducted using the SOLPS-ITER plasma edge code package and the DIVIMP impurity tracking code. The inboard baffle of the current SAS divertor will be shifted closer to the outboard baffle, creating a V-corner at the slot vertex. In addition, the outboard baffle will be coated with 10–15 μm of W for experiments studying high-Z sourcing and leakage in a closed divertor. Modeling of the 'SAS-VW' divertor predicts that these changes to the inner baffle will reduce W gross erosion by 40× relative to the existing SAS divertor when the outer strike point (OSP) is at the V-corner and the ion B × ∇B drift is towards the divertor, driven primarily by significant cooling near the slot vertex. Most W erosion in SAS-VW is expected to occur near the slot entrance, which may pose a higher risk to core contamination than W eroded deeper in the slot. Furthermore, adding a new sheath-based prompt redeposition model increases the sensitivity of redeposition estimates to near-target plasma conditions and may provide more accurate predictions of net erosion. Moving the OSP outboard from the slot vertex ~4 cm onto the W-coated region yields a 40× increase in the gross erosion rate and a 50% decrease in the core leakage fraction. Thus slight variations in strike point location may counteract the potential benefits of the tightly-baffled V slot on minimizing erosion. This impurity transport modeling provides useful guidance for future experiments on the SAS-VW divertor focused on high-Z erosion/redeposition, scrape-off layer transport, and core leakage.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Erosion products of plasma facing materials formed under ITER-like transient load and deuterium retention in them

Erosion of the plasma-facing materials in particular evaporation of the materials in a fusion reactor under intense transient events is one of the problems of the ITER. The current experimental data are insufficient to predict the properties of the erosion products, a significant part of which will be formed during transient events (edge-localized modes (ELMs) and disruptions). The paper concerns the experimental investigation of the graphite and tungsten erosion products deposited under pulsed plasma load at the QSPA-T: heat load on the target was 2.6 MJ/m{sup 2} with 0.5 ms pulse duration. The designed diagnostics for measuring the deposition rate made it possible to determine that the deposition of eroded material occurs during discharge, and the deposition rate is in the range (0.1–100) × 10{sup 19} at/(cm{sup 2} s), which is much higher than that for stationary processes. It is found that the relative atomic concentrations D/C and D/(W + C) in the erosion products deposited during the pulse process are on the same level as for the stationary processes. An exposure of erosion products to photonic energy densities typical of those expected at mitigated disruptions in the ITER (pulse duration of 0.5–1 ms, integral energy density of radiation of 0.1–0.5 MJ/m2) significantly decreases the concentration of trapped deuterium.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Erosion-Corrosion Detection in Carbon Steel Pipe Loops using SRNLs Thickness and Mass Loss Measurement Coupons - 20464

Structural health of waste transfer infrastructure is of utmost importance to DOE and communities surrounding their active sites. A Fitness-for-Service (FFS) program for the Waste Transfer System has been implemented by the US Department of Energy (DOE) for the purposes of evaluating and quantifying the degradation of critical components. Currently, the method of approach is to section and evaluate pipelines that have been removed at end service. In order to augment data collection methods applied to making lifespan estimates of waste transfer system components, Florida International University (FIU) has been investigating new-technology based strategies for quantifying the rate of degradation. Present research considers the option of a coupon system installed on a section of pipe at points of interest that will provide easy access to high resolution measurements of erosion/corrosion rates during operation. Researchers at Savannah River National Laboratory (SRNL) have developed this novel solution for in situ erosion and corrosion measurements in many applicable locations such as tanks, pipes, ducts, and injection points. The coupons are approximately 12.7 mm (1/2 inch) in diameter and 25.4 mm (1 inch) in length and can be placed in the pipe sections using Swagelok compression fittings. The coupon design allows for monitoring of the total degradation resulting from corrosion and erosion. High-resolution Ultrasonic Thickness (UT) testing allows in-situ monitoring of both degradation mechanisms. When removed from the system mass loss resulting from corrosion and erosion may also be evaluated. Experimental testing at FIU implemented the SRNL coupon system in a 6.10 meter (20 foot) pipe loop system comprised of 50.8 mm (2 inch) and 76.2 mm (3 inch) pipe sections in order to replicate expected use cases at the sites. Operational conditions were emulated by pumping abrasive materials through the pipeline at full capacity and collecting measurements from the SRNL coupons. Initial testing was conducted by circulating water followed by a mixture of sand and water for uniform wear rates. Thickness changes and mass loss were measured, and the surface exposed to the process fluid was observed for visual evidence of characteristic wear patterns resulting from an erosive environment. The test matrix consisted of several hours of operation and using fine, medium and coarse grain sands. Test results were analyzed to check for all three parameters (mass loss/gain, thickness change and surface patters) which could provide estimates of the remaining useful life of the pipe sections. Thus, the research presents the findings of this evaluation of the SRNL coupons as a means for conducting high accuracy, cost effective in-situ analysis of pipeline and waste transfer systems for erosion and corrosion susceptibility. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

High-Temperature Erosive Behavior of Plasma Sprayed Cr{sub 3}C{sub 2}-NiCr/Cenosphere Coating

This research examines the deposition of Cr{sub 3}C{sub 2}-NiCr/cenosphere and Cr{sub 3}C{sub 2}-NiCr coatings on MDN 321 steel through the process of plasma spray. In this process, the solid particle erosion test is established at 200, 400, 600 °C with 30° and 90° impact angles. Alumina erodent is adopted to investigate the erosive behavior of the coating at higher temperatures. The properties of the Cr{sub 3}C{sub 2}-NiCr/cenosphere coating are established based on the microhardness, the adhesive strength, the fracture toughness, and the ductility. To quantify volume loss as a result of erosion, an optical profilometer is used. At higher temperature, decrease in the erosion volume loss of Cr{sub 3}C{sub 2}-NiCr/cenosphere and Cr{sub 3}C{sub 2}-NiCr coatings is observed. The erosion-resistive property of Cr{sub 3}C{sub 2}-NiCr/cenosphere coating is higher than that of MDN 321 steel by 76%. This property is influenced by high-temperature stability of mullite, alumina, and protective oxide layer that is formed at elevated temperatures. The morphology of eroded coating discloses a brittle mode of material removal.

36 MATERIALS SCIENCE↗

A simple model for estimating changes in rainfall erosivity caused by variations in rainfall patterns

Highlights: • A simple relationship was developed for predicting daily erosivity in changing climates. • The relationship depends on precipitation amount and maximum 0.5-h intensity I{sub 0.5} . • The relationship was calibrated using measured climate data and had a R{sup 2} of 0.99. • Simulated daily and annual erosivities were predicted with a R{sup 2} of 0.99 using the relationship. • The relationship was tested using I{sub 24}, showing a R{sup 2} of 0.78 for the simulated data. A major challenge when coupling soil loss models with precipitation forecasts from Global Circulation Models (GCMs) is that their time resolutions do not generally agree. Precipitation forecasts from GCM must be scaled down; however, the distribution of the rainfall intensity, which can affect soil loss as much as precipitation amounts, is usually not considered in this process. Therefore, the objective of this study was to develop a statistical equation for computing event-based rainfall erosivity under changing precipitation patterns using the least amount of information possible. For this purpose, an empirical equation for predicting event-based rainfall erosivity was developed using the product of the total precipitation P and the maximum 0.5-h rainfall intensity, I{sub 0.5}. This equation was calibrated using measured precipitation data from 28 sites in Central Chile and then tested with simulated data with different rainfall patterns from the CLIGEN (CLImate GENerator) weather generator. More than 53,000 rainfall events were analyzed, where the equation consistently provided R{sup 2} values of 0.99 for every dataset used, revealing its robustness when used in potential climate change scenarios in the study site. However, because computing I{sub 0.5} requires estimating precipitation at a high time resolution, the relationship was recalibrated and tested using 1 through 24-h maximum rainfall intensities. Using these intensities, the equation provided erosivity estimates with R{sup 2} ranging from 0.78 to 0.99, where better results were obtained as the resolution of the data increased. This study provides the methodology for building and testing the proposed equation and discusses its advantages and limitations.

54 ENVIRONMENTAL SCIENCES↗

Survey of tungsten gross erosion from main plasma facing components in WEST during a L-mode high fluence campaign

An initial high fluence campaign was performed in WEST, in 2023, on the newly installed actively cooled tungsten divertor composed of ITER-grade monoblocks. The campaign consisted in the repetition of a 60 s long Deuterium L-mode pulse in attached divertor conditions, cumulating over 10000s of plasma exposure. A maximum deuterium fluence of approximately 5⋅1⁢026 m−2 was reached in the outer strike point region, representative of a few high performance ITER pulses. Gross tungsten erosion inferred from visible spectroscopy shows that the most eroded plasma facing component is the inner divertor target with rates ten times larger than on the outer divertor target. The outer midplane tungsten bumpers, located a few centimeters from the plasma, show gross erosion rates two times lower than at the outer divertor. We conclude that the outer midplane bumpers have a negligible contribution to the long range tungsten migration and deposition onto the lower divertor. The cumulated gross erosion rate on the inner divertor translates in an effective gross erosion thickness of about 20μ⁢m, while it is about 2μ⁢m for the outer divertor. Strikingly, these orderings coincide with the thickness of deposits found locally on the divertor: the exposed surfaces of high field side monoblocks are covered with several tens of μ⁢m tungsten deposits, while on the lower field side, few μ⁢m thin tungsten deposits are only found on the magnetically shadowed parts of monoblocks. The strong impact of those deposits on WEST operation, namely perturbation of surface temperature measurement with infra-red thermography, and the emission of flakes causing radiative perturbation of the confined plasma, calls for anticipating similar issues in ITER. In particular, the start of research operation shall consider the definition of a divertor erosion budget in order to anticipate the formation of deleterious deposits.

Fedorczak, N.↗

Tungsten erosion during L-mode discharges in the DIII-D SAS-VW divertor

A series of L-mode plasma discharges was performed in the DIII-D tokamak to assess the impact of outer strike point (OSP) position and toroidal magnetic field direction on erosion and core contamination potential of the recently-installed, tungsten-coated Small Angle Slot (SAS-VW) divertor. In one discharge, in-slot emission spectroscopy measured an<48 % increase in the W gross erosion rate when the OSP was moved 3 cm outwards, away from the V-shaped vertex of the slot divertor. However, the effective W yield (erosion rate divided by the incident D flux) was, overall, insensitive to changes in OSP location. Consistently low estimates of the effective W yield based on measurements taken a few cm outwards from the vertex suggest potentially significant C surface contamination. No W emission signal was detected when orienting the toroidal magnetic field such that the ion B×∇B drift direction is pointed away from the X-point. However, measurements of W content in the plasma core for both toroidal magnetic field directions suggest the presence of additional, unmeasured sources of erosion. The difference in the measured core W density with OSP position is much greater than the difference in the measured erosion rates, which may suggest that the leakage of eroded impurities out of the divertor is governed primarily through the parallel ion temperature gradient and friction forces.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Melt-driven erosion in microparticle impact

Impact-induced erosion is the ablation of matter caused by being physically struck by another object. While this phenomenon is known, it is empirically challenging to study mechanistically because of the short timescales and small length scales involved. Here, we resolve supersonic impact erosion in situ with micrometer- and nanosecond-level spatiotemporal resolution. We show, in real time, how metallic microparticles (~10-μm) cross from the regimes of rebound and bonding to the more extreme regime that involves erosion. We find that erosion in normal impact of ductile metallic materials is melt-driven, and establish a mechanistic framework to predict the erosion velocity.

36 MATERIALS SCIENCE↗

Suppressed gross erosion of high-temperature lithium via rapid deuterium implantation

Lithium-coated high-Z substrates are planned for use in the NSTX-U divertor and are a candidate plasma facing component (PFC) for reactors, but it remains necessary to characterize the gross Li erosion rate under high plasma fluxes (>10 23 m -2 s -1 ), typical for the divertor region. In this work, a realistic model for the compositional evolution of a Li/D layer is developed that incorporates first principles molecular dynamics (MD) simulations of D diffusion in liquid Li. Predictions of Li erosion from a mixed Li/D material are also developed that include formation of lithium deuteride (LiD). The erosion rate of Li from LiD is predicted to be significantly lower than from pure Li. This prediction is tested in the Magnum-PSI linear plasma device at ion fluxes of 10 23 -10 24 m -2 s -1 and Li surface temperatures. ≤800 °C. Li/LiD coatings ranging in thickness from 0.2 to 500 μm are studied. The dynamic D/Li concentrations are inferred via diffusion simulations. The pure Li erosion rate remains greater than Langmuir Law evaporation, as expected. For mixed-material Li/LiD surfaces, the erosion rates are reduced, in good agreement with modelling in almost all cases. Lastly, these results imply that the temperature limit for a Li-coated PFC may be significantly higher than previously imagined.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Development of Corrosion- and Erosion-Resistant Coatings for Advanced Ultra-Supercritical Materials

This final report summarized the research efforts and major findings of the Phase I Project “Development of Corrosion- and Erosion-Resistant Coatings for Advanced Ultra-Supercritical Materials”, for the period of October 1, 2019 – Sept. 30, 2021. This project is a collaborative endeavor between Tennessee Tech University, Purdue University, Oak Ridge National Laboratory, Siemens Corporation, and Eastern Plating, LLC, aiming at improving the durability and lifetime of high-pressure (HP) steam turbine blades in advanced ultra-supercritical (A-USC) coal-fired power plants through the development of corrosion/erosion-resistant coatings manufactured via a low-cost electrolytic codeposition process. While Tribaloy alloy T-400C was identified by the U.S. A-USC Materials Consortium as a promising coating composition, further composition optimization is needed to enhance its corrosion and erosion resistance for protecting the A-USC Ni-base turbine components. An integrated computational and experimental approach was employed to optimize coating composition/microstructure and processing parameters. In order to identify candidate coating compositions that could offer balanced properties, thermodynamic calculations were performed to explore the γ+Laves composition space in the Co-Ni-Cr-Mo-Si system with different alloying additions at 600-800 °C. Guided by the calculation results, experimental assessment of selected alloys led to the development of a new generation of Tribaloy compositions with the optimal levels of Cr, Mo and Si, reactive element (e.g., 0.4-0.6 wt.% Y) and other alloying additions. The low-cost and non-line-of-sight electro-codeposition process was employed to deposit a Ni(Co)-CrMoSiY composite coating on commercial Haynes 282 (H282) Ni-base alloy. A diffusion treatment was subsequently applied to convert the composite to the Tribaloy-type coating. Both the codeposition parameters and heat treatment conditions were varied to achieve the desired coating composition, microstructure and phase constituents. In addition, since additive manufacturing (AM) may be an alternative cost-saving option for potential A-USC turbine repair, laser direct deposition was explored to fabricate the H282 alloy with minimal defects. The electro-codeposited Tribaloy coating was also applied to the AM H282 substrate to demonstrate the viability of the coating process in improving the surface finish of AM alloys. Both high-temperature oxidation performance and solid particle erosion (SPE) resistance of model alloys and electro-codeposited coatings were evaluated. About 25 model alloys with various Cr/Mo ratios and reactive element levels, as well as partial substitution of Mo with Nb were evaluated with regard to their oxidation resistance in both air and pure steam at 760-800°C. Compositions based on Ni(Co)-20Cr-18Mo-2.6Si-0.6Y (wt.%) showed significantly improved oxidation resistance over the baseline T400-C. Based on the alloy development results, three generations of new Tribaloy coatings (Gen-1, Gen-2, and Gen-3) with various Mo/Cr contents and Y levels were prepared via electro-codeposition and their microstructure/performance were evaluated. Outstanding air and steam oxidation resistance was achieved for the Gen-2 and Gen-3 coatings. Furthermore, while the SPE resistance of the coatings depended on many factors such as temperature, environment, erodent, velocity and impact angle, the coated samples exhibited similar or better SPE resistance compared to the H282 substrate when magnetite was used as erodent (which is a realistic erodent in A-USC steam turbines). The new Tribaloy coatings also had good long-term compatibility with the H282 alloy substrate. The two large-sized rotating barrels were designed, constructed, and employed to coat dummy HP blades. Uniform coating thickness and microstructure were achieved at various blade locations. Also, a preliminary techno-economic analysis of the proposed coating process was conducted to quantify the cost-effectiveness and to assess the commercial viability of the corrosion- and erosion-resistant coatings. It is estimated that a cost reduction of ~30% could be achieved with the electro-codeposition coating process over the state-of-the-art high velocity oxygen fuel (HVOF) thermal spray. Compared to the leading Tribaloy coating technologies such as HVOF and plasma transfer alloying, electro-codeposition based process has advantages such as low-cost process equipment, uniform deposition even for complex shapes, low levels of contaminants/porosities, reduction of powder waste, and potentially better surface finish and longer turbine service life. The Phase 1 study has demonstrated that it is feasible to develop an electro-codeposited Tribaloy coating with balanced corrosion and erosion properties, even though additional research efforts such as further coating process scale-up and longer-term performance evaluation under realistic A-USC conditions are clearly needed.

20 FOSSIL-FUELED POWER PLANTS↗

Phenomena Identification and Ranking Tables (PIRT) analysis of wind turbine blade leading edge erosion

Leading edge erosion (LEE) of wind turbine blades has been identified as a major factor in decreased wind turbine blade lifetimes and energy output over time. Accordingly, the International Energy Agency Wind Technology Collaboration Programme (IEA Wind TCP) has created the Task 46 Phase 2 to undertake cooperative research in the key topic of blade erosion. The purpose of Task 46 Erosion Phase 2 is to further improve understanding of erosion driving factors, develop datasets and model tools to enhance prediction of leading-edge erosion likelihood, identify damage at the earliest possible stage and advance potential solutions. The scope of work covers several technical areas, reflecting the multidisciplinary nature of the challenge. Participants in the task are given in Table 1.

17 WIND ENERGY↗

Early-to-mid Miocene erosion rates inferred from pre-Dead Sea rift Hazeva River fluvial chert pebbles using cosmogenic 21 Ne

In this work, we utilize a novel application of cosmogenic 21 Ne measurements in chert to compare exposure times measured in eroding surfaces in the central Jordanian Plateau with exposure times from chert pebbles transported by the Miocene Hazeva River. The Miocene Hazeva River was a large fluvial system (estimated catchment size > 100 000 km 2 ) that drained the Arabian Plateau and Sinai Peninsula into the Mediterranean Sea during the early-to-mid Miocene. It was established after the rifting of the Red Sea uplifted the Arabian Plateau during the Oligocene. Following late-Miocene-to-early-Pliocene subsidence along the Dead Sea rift, the Hazeva drainage system was abandoned and dissected, resulting in new drainage divides on either side of the rift. We find modern erosion rates derived from cosmogenic 21 Ne, 26 Al, and 10Be in exposed in situ chert nodules to be extremely slow (between 2–4 mm kyr -1 ). Comparison between modern and paleo-erosion rates, measured in chert pebbles, is not straightforward, as cosmogenic 21 Ne was acquired partly during bedrock erosion and partly during transport of these pebbles in the Hazeva River. However, 21 Ne exposure times calculated in Miocene cherts are generally shorter (ranging between $0^{+59}_{-0}$ and 242±113 kyr) compared to exposure times calculated in the currently eroding chert nodules presented here (269±49 and 378±76 kyr) and other chert surfaces currently eroding in hyperarid environments. Miocene exposure times are shorter even when considering that they account for bedrock erosion in addition to maintained transport along this large river. Shorter exposure times in Miocene cherts correspond to faster paleo-erosion rates, which we attribute to a combination of continuous surface uplift and significantly wetter climatic conditions during the early-to-mid Miocene.

58 GEOSCIENCES↗