Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELECTROMECHANICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Evaluation of Electromechanical Systems Dynamically Emulating a Candidate Hydrokinetic Turbine

The use of controllable motor-generator sets to emulate the dynamics of a hydrokinetic turbine is evaluated as an alternative to field testing a prototype. The emulator control dynamic equations are presented, methods for scaling turbine parameters are examined, and experimental results are presented from three electromechanical emulation machines (EEMs) programmed to emulate the same vertical-axis fixed-pitch turbine. Although hardware platforms and control implementations varied, results show that each EEM is successful in emulating the turbine model, thus demonstrating the general feasibility of the approach. However, performance of motor control under torque command, current command or speed command differed. In one of the EEMs evaluated, the power take off controller tracks the maximum power-point of the turbine in response to turbulence. Utilizing realistic inflow conditions and control laws, the emulator dynamic speed response is shown to agree well at low frequencies with numerical simulation but to deviate at high frequencies.

13 HYDRO ENERGY↗

Designing Piezoelectric Films for Micro Electromechanical Systems

Piezoelectric thin films are of increasing interest in low-voltage micro electromechanical systems for sensing, actuation, and energy harvesting. They also serve as model systems to study fundamental behavior in piezoelectrics. Next-generation technologies such as ultrasound pill cameras, flexible ultrasound arrays, and energy harvesting systems for unattended wireless sensors will all benefit from improvements in the piezoelectric properties of the films. This paper describes tailoring the composition, microstructure, orientation of thin films, and substrate choice to optimize the response. It is shown that increases in the grain size of lead-based perovskite films from 75 to 300 nm results in 40 and 20% increases in the permittivity and piezoelectric coefficients, respectively. This is accompanied by an increase in the nonlinearity in the response. Band excitation piezoresponse force microscopy was used to interrogate the nonlinearity locally. It was found that chemical solution-derived PbZr(0.52)Ti(0.48)O(3) thin films show clusters of larger nonlinear response embedded in a more weakly nonlinear matrix. The scale of the clusters significantly exceeds that of the grain size, suggesting that collective motion of many domain walls contributes to the observed Rayleigh behavior in these films. Finally, it is shown that it is possible to increase the energy-harvesting figure of merit through appropriate materials choice, strong imprint, and composite connectivity patterns.

Trolier-McKinstry, Susan↗

Relaxor ferroelectric polymer exhibits ultrahigh electromechanical coupling at low electric field

Electromechanical (EM) coupling—the conversion of energy between electric and mechanical forms—in ferroelectrics has been used for a broad range of applications. Ferroelectric polymers have weak EM coupling that severely limits their usefulness for applications. Here, we introduced a small amount of fluorinated alkyne (FA) monomers (<2 mol %) in relaxor ferroelectric poly(vinylidene fluoride-trifluoroethylene-chlorofluoroethylene) (PVDF-TrFE-CFE) terpolymer that markedly enhances the polarization change with strong EM coupling while suppressing other polarization changes that do not contribute to it. Under a low–dc bias field of 40 megavolts per meter, the relaxor tetrapolymer has an EM coupling factor (k 33 ) of 88% and a piezoelectric coefficient (d 33 ) >1000 picometers per volt. These values make this solution-processed polymer competitive with ceramic oxide piezoelectrics, with the potential for use in distinct applications.

36 MATERIALS SCIENCE↗

Ferroelectric materials toward next-generation electromechanical technologies

Ferroelectric materials have been widely used in various electromechanical devices, from ultrasonic transducers and actuators to mechanical energy harvesters. The key performance metrics of these devices, such as sensitivity, efficiency, and bandwidth of ultrasonic transducers, are largely determined by the piezoelectric properties. This Review highlights recent research progress in improving the piezoelectricity of ferroelectric materials and offers potential strategies for further enhancement to meet the ever-increasing demands for high-performance piezoelectric devices and systems. Here, it provides insights into the future development of ferroelectrics to address the increasing demands of emerging applications, including photoacoustic imaging and piezoelectric fans and motors in integrated circuit–enabled electronic devices. Additionally, it emphasizes the need to consider environmental impacts across the entire life cycle of ferroelectrics, from sourcing and manufacturing to usage and disposal.

36 MATERIALS SCIENCE↗

A Fully Coupled Model for Electromechanics of the Heart

We present a fully coupled electromechanical model of the heart. The model integrates cardiac electrophysiology and cardiac mechanics through excitation-induced contraction and deformation-induced current. Numerical schemes based on finite element were implemented in a supercomputer. Numerical examples were presented using a thin cardiac tissue and a dog ventricle with realistic geometry. Performance of the parallel simulation scheme was studied. The model provides a useful tool to understand cardiovascular dynamics.

42 ENGINEERING↗

Defect-related hysteresis in nanotube-based nano-electromechanical systems

The electronic properties of multi-walled carbon nanotubes (MWCNTs) depend on the positions of their walls with respect to neighboring shells. This fact can enable several applications of MWCNTs as nano-electromechanical systems (NEMS). In this article, we report the findings of a first-principles study on the stability and dynamics of point defects in double-walled carbon nanotubes (DWCNTs) and their role in the response of the host systems under inter-tube displacement. Key defect-related effects, namely, sudden energy changes and hysteresis, are identified, and their relevance to a host of MWCNT-based NEMS is highlighted. The results also demonstrate the dependence of these effects on defect clustering and chirality of DWCNT shells.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Algorithm Summary and Evaluation: Automatic Implementation of Ringdown Analysis for Electromechanical Mode Identification from Phasor Measurements

Small signal stability problems are one of the major threats to grid stability and reliability. Prony analysis has been successfully applied on ringdown data to monitor electromechanical modes of a power system using phasor measurement unit (PMU) data. To facilitate an on-line application of mode estimation, this paper develops a recursive algorithm for implementing Prony analysis and proposed an oscillation detection method to detect ringdown data in real time. By automatically detecting ringdown data, the proposed method helps guarantee that Prony analysis is applied properly and timely on the ringdown data. Thus, the mode estimation results can be performed reliably and timely. The proposed method is tested using Monte Carlo simulations based on a 17-machine model and is shown to be able to properly identify the oscillation data for on-line application of Prony analysis. In addition, the proposed method is applied to field measurement data from WECC to show the performance of the proposed algorithm.

24 POWER TRANSMISSION AND DISTRIBUTION↗

A Theoretical Analysis on the Dynamic Behavior and Electromechanical Response of PZT

Piezoelectric materials are used as a power source in stockpile components for safety and reliability assurances. The objective of this project is to gain insights into the fundamental pressure-induced behavior and electromechanical response of lead zirconate titanate (PZT). Specifically, to establish the basis for an accurate, physics-based material model for robust model-based design to rapidly optimize PZT-based materials and components for performance studies. Established ab-initio methods are used to interrogate and understand the dynamic behavior of PZT as a function of composition (50/50, 65/35, 80/20, 95/5) and dopants (La, Nb) to overcome the costly and time-consuming experimental methodologies. New cold curves for pure and doped single-crystal PZT are obtained as the reference equation-of-state (EOS). A negligible change in the pressure responses was observed for the systems and strains studied. Dielectric and piezoelectric responses of pure and doped single-crystal PZT were also calculated as a function of pressure. For undoped PZT, there is a clear and orderly pressure and composition dependence. For doped PZT, there is a significant increase in the responses, but the behavior is very disordered and inconclusive.

36 MATERIALS SCIENCE↗

A Vibrational Energy Harvesting Sensor Based on Linear and Rotational Electromechanical Effects

In this investigation, a magnetically coupled double-spring design is presented for harvesting low-level non-stationary random vibrational energy. The sensor relies on multimodal coupling between the translation and rotation of a two-spring magnet and coil system to widen the harvesting bandwidth. Energy methods are used to develop a model to characterize the electromechanical response of the system, the solution of which is obtained using stochastic techniques based on a particle swarm algorithm. This approach provides an efficient method to estimate system parameters that otherwise are difficult or impossible to determine with independent measurements. The experimental results demonstrate agreement with the theoretical predictions over a limited bandwidth. The sensor can effectively harvest non-stationary vibration energy down to 10 -4 g within a limited bandwidth of 130–150 Hz. The sensor prototype has an operational volume of 2.6 cm 3 with a calculated power density of 0.2 W/cm 3 . The sensor’s small size results in a coupling efficiency of approximately 6% across the tested bandwidth.

42 ENGINEERING↗

Investigating the Electromechanical Sensitivity of Carbon-Nanotube-Coated Microfibers

The piezoresistance of carbon nanotube (CNT)-coated microfibers is examined using diametric compression. Diverse CNT forest morphologies were studied by changing the CNT length, diameter, and areal density via synthesis time and fiber surface treatment prior to CNT synthesis. Large-diameter (30–60 nm) and relatively low-density CNTs were synthesized on as-received glass fibers. Small-diameter (5–30 nm) and-high density CNTs were synthesized on glass fibers coated with 10 nm of alumina. The CNT length was controlled by adjusting synthesis time. Electromechanical compression was performed by measuring the electrical resistance in the axial direction during diametric compression. Gauge factors exceeding three were measured for small-diameter (<25 μm) coated fibers, corresponding to as much as 35% resistance change per micrometer of compression. The gauge factor for high-density, small-diameter CNT forests was generally greater than those for low-density, large-diameter forests. A finite element simulation shows that the piezoresistive response originates from both the contact resistance and intrinsic resistance of the forest itself. The change in contact and intrinsic resistance are balanced for relatively short CNT forests, while the response is dominated by CNT electrode contact resistance for taller CNT forests. These results are expected to guide the design of piezoresistive flow and tactile sensors.

36 MATERIALS SCIENCE↗

Polar Nanoregions and Relaxors: How Nanoscale Disorder Leads to Enormous Electromechanical Response (438th Brookhaven Lecture)

Relaxors is the name given to a special class of materials called relaxor ferroelectrics. Xu will describe a series of experiments done by BNL researchers with collaborators from Stony Brook University, Johns Hopkins University, and the National Institute of Standards and Technology, to discover why relaxors have such an exceptional electromechanical response. The explanation is dependent on "polar nanoregions" -- tiny, nanometer-scale regions within the relaxors. The team established a link between polar nanoregions and the relaxors' ability to deform in response to an electric field, or to have a pulse of electric current induced by a deforming physical force. This understanding promises to lead to more improvements to relaxor materials for an even greater variety of applications.

30 DIRECT ENERGY CONVERSION↗

Space vehicle electromechanical system and helical antenna winding fixture

A space vehicle electromechanical system may employ an architecture that enables convenient and practical testing, reset, and retesting of solar panel and antenna deployment on the ground. A helical antenna winding fixture may facilitate winding and binding of the helical antenna.

33 ADVANCED PROPULSION SYSTEMS↗

Attenuation of spurious responses in electromechanical filters

A spur cancelling, electromechanical filter includes a first resonator having a first resonant frequency and one or more first spurious responses, and it also includes, electrically connected to the first resonator, a second resonator having a second resonant frequency and one or more second spurious responses. The first and second resonant frequencies are approximately identical, but the first resonator is physically non-identical to the second resonator. The difference between the resonators makes the respective spurious responses different. This allows for filters constructed from a cascade of these resonators to exhibit reduced spurious responses.

42 ENGINEERING↗

Estimation of Electromechanical Modes of Oscillation in the Eastern Interconnection from Ambient PMU Data

A power system's inter-area electromechanical modes of oscillation determine if the system is small-signal stable. Mode meters are tools that estimate the modes based on ambient synchrophasor measurements, allowing continuous monitoring of the system's stability margin. This paper reports on the application of mode meter algorithms to 21 months of synchrophasor measurements from the United States Eastern Interconnection (EI). Estimates for three modes were updated every minute, providing a much more comprehensive set of results than previous studies based on disturbance recordings. The detailed signal designs and mode meter configurations provided in this paper can be used to accelerate mode meter deployments in the EI. Analysis of the mode estimates reveal for the first time how seasonal load changes and system reconfiguration impact the EI system's dynamics.

Follum, James D.↗

Nano-electromechanical rotation of graphene and giant enhancement in dielectric anisotropy in a liquid crystal

A nematic liquid crystal (LC) is doped with dilute concentrations of pristine monolayer graphene (GP) flakes, and the LC + GP hybrids are found to exhibit a dramatic increase in the dielectric anisotropy. Electric field-dependent conductance studies reveal that the graphene flakes follow the nematic director that mechanically rotates on increasing an applied electric field. Further studies show that the π–π electron stacking, between the graphene's honeycomb structure and the LC's benzene rings, stabilizes pseudo-nematic domains that collectively amplify the dielectric anisotropy by improving the orientational order parameter in the nematic phase. These anisotropic domains interact with the external electric field, resulting in a nonzero dielectric anisotropy in the isotropic phase as well. The enhancement in dielectric anisotropy, due to the LC–graphene coupling, is found to have subsequent positive impacts on the LC's orientational threshold field and elasticity that allows the nematic director to respond quicker on switching the electric field off.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗