Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dynamic Procedures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Economy of precipitating agent application in municipal wastewater treatment facilities

Purification by precipitation in this study is not considered primarily as a means of phosphate removal but as a method for reduction of suspended solids BOD and COD. A dynamic calculation procedure is used to allow for exact determination of time dependent variation of costs. The results show that costs of wastewater treatment by precipitation may equal those of conventional primary clarification and secondary biological treatment, especially with low-cost iron-II-salts in simultaneous precipitation and in larger plants ( 20,000 PF). Cost advantages may be accrued in smaller plants by using the more expensive trivalent salts in pre-precipitation as compared to conventional low-load biological treatment. This is due mainly to better effluent quality and, consequently, lower wastewater fees (Wastewater Discharge Act). If the precipitant is dosed temporarily only during periods of highest pollution the savings can be about 5 to 10%.

Neis, U.↗
NASA NTRS1981

A mesoscale sixth-order numerical modelling system

A numerical simulation system is currently under development for NASA which is intended to improve the modeling of subsynoptic and mesoscale adjustments associated with cyclogenesis, severe storm development and atmospheric transport processes. The model utilizes a standard hydrostatic sigma-p coordinate primitive equation set, with x,y-space differencing accurate to eighth order. A three-step dynamic initialization procedure is employed between the analysis of real-time data and grid interpolation. Results of an 18-hour simulation during which synoptic scale cyclogenesis, subsynoptic scale jet streak adjustments, mesoscale convergence zones and tornadic storms were observed have shown the present model to have the potential for simulating the fine-scale structure of features associated with cyclogenesis and intense squall-line development. The mesoscale model was also found to produce less truncation than the NWS LFM model, although a frictionless version of the mesoscale model somewhat overdeepens and overaccelerates features.

Kaplan, M. L.↗
NASA NTRS1987

Properties of low-energy electron precipitation in the cleft during periods of unusually high ambient electron temperatures

A recently developed automated fitting procedure for Dynamics Explorer 2 electron energy spectra represents each auroral electron spectrum as a superposition of several Maxwellian and several Gaussian components. The fitting parameters give a digital representation which uniquely describes each spectrum. It is shown that unusually high ambient electron temperatures (of the order of 10,000 K) in the cleft are strongly correlated with the intensity parameters of the lowest-temperature Maxwellian components of the precipitation. The collisional heat input into the ambient electrons by these Maxwellian components of the precipitation fluxes is shown to be more than an order of magnitude higher in the high-temperature storm time cases than it is in a control set of 'normal temperature' quiet time cases. The heating effect of the solar flux is shown to be nearly the same for both sets of cases. As a result it is concluded that electron precipitation is the chief mechanism responsible for those high ambient temperatures.

Fontheim, Ernest G.↗
NASA NTRS1990

Numerically Controlled Machining Of Wind-Tunnel Models

New procedure for dynamic models and parts for wind-tunnel tests or radio-controlled flight tests constructed. Involves use of single-phase numerical control (NC) technique to produce highly-accurate, symmetrical models in less time.

Kovtun, John B.↗
NASA NTRS1989

Real-time neuromorphic algorithms for inverse kinematics of redundant manipulators

The paper presents an efficient neuromorphic formulation to accurately solve the inverse kinematics problem for redundant manipulators. The approach involves a dynamical learning procedure based on a novel formalism in neural network theory: the concept of 'terminal' attractors. Topographically mapped terminal attractors are used to define a neural network whose synaptic elements can rapidly encapture the inverse kinematics transformations, and, subsequently generalize to compute joint-space coordinates required to achieve arbitrary end-effector configurations. Unlike prior neuromorphic implementations, this technique can also systematically exploit redundancy to optimize kinematic criteria, e.g., torque optimization. Simulations on 3-DOF and 7-DOF redundant manipulators, are used to validate the theoretical framework and illustrate its computational efficacy.

Barhen, Jacob↗
NASA NTRS1990

Continuous assimilation of simulated Geosat altimetric sea level into an eddy-resolving numerical ocean model. I - Sea level differences. II - Referenced sea level differences

The optimal interpolation method of Lorenc (1981) was used to conduct continuous assimilation of altimetric sea level differences from the simulated Geosat exact repeat mission (ERM) into a three-layer quasi-geostrophic eddy-resolving numerical ocean box model that simulates the statistics of mesoscale eddy activity in the western North Pacific. Assimilation was conducted continuously as the Geosat tracks appeared in simulated real time/space, with each track repeating every 17 days, but occurring at different times and locations within the 17-day period, as would have occurred in a realistic nowcast situation. This interpolation method was also used to conduct the assimilation of referenced altimetric sea level differences into the same model, performing the referencing of altimetric sea sevel differences by using the simulated sea level. The results of this dynamical interpolation procedure are compared with those of a statistical (i.e., optimum) interpolation procedure.

White, Warren B.↗
NASA NTRS1990

Dissipative compensators for flexible spacecraft control

The problem of controller design for flexible spacecraft is addressed. Model-based compensators, which rely on the knowledge of the system parameters to tune the state estimator, are considered. The instability mechanisms resulting from high sensitivity to parameter uncertainties are investigated. Dissipative controllers, which use collocated actuators and sensors, are also considered, and the robustness properties of constant-gain dissipative controllers in the presence of unmodeled elastic-mode dynamics, sensor/actuator nonlinearities, and actuator dynamics are summarized. In order to improve the performance without sacrificing robustness, a class of dissipative dynamic compensators is proposed and is shown to retain robust stability in the presence of second-order actuator dynamics if acceleration feedback is employed. A class of dissipative dynamic controllers is proposed which consists of a low-authority, constant-gain controller and a high-authority dynamic compensator. A procedure for designing an optimal dissipative dynamic compensator is given which minimizes a quadratic performance criterion. Such compensators offer the promise of better performance while still retaining robust stability.

Joshi, S. M.↗
NASA NTRS1991

Transformation of two and three-dimensional regions by elliptic systems

A reliable linear system is presented for grid generation in 2-D and 3-D. The method is robust in the sense that convergence is guaranteed but is not as reliable as other nonlinear elliptic methods in generating nonfolding grids. The construction of nonfolding grids depends on having reasonable approximations of cell aspect ratios and an appropriate distribution of grid points on the boundary of the region. Some guidelines are included on approximating the aspect ratios, but little help is offered on setting up the boundary grid other than to say that in 2-D the boundary correspondence should be close to that generated by a conformal mapping. It is assumed that the functions which control the grid distribution depend only on the computational variables and not on the physical variables. Whether this is actually the case depends on how the grid is constructed. In a dynamic adaptive procedure where the grid is constructed in the process of solving a fluid flow problem, the grid is usually updated at fixed iteration counts using the current value of the control function. Since the control function is not being updated during the iteration of the grid equations, the grid construction is a linear procedure. However, in the case of a static adaptive procedure where a trial solution is computed and used to construct an adaptive grid, the control functions may be recomputed at every step of the grid iteration.

Mastin, C. Wayne↗
NASA NTRS1996

Heat Transfer Experiments in the Internal Cooling Passages of a Cooled Radial Turbine Rotor

An experimental study was conducted (1) to experimentally measure, assess and analyze the heat transfer within the internal cooling configuration of a radial turbine rotor blade and (2) to obtain heat transfer data to evaluate and improve computational fluid dynamics (CFD) procedures and turbulent transport models of internal coolant flows. A 1.15 times scale model of the coolant passages within the NASA LERC High Temperature Radial Turbine was designed, fabricated of Lucite and instrumented for transient beat transfer tests using thin film surface thermocouples and liquid crystals to indicate temperatures. Transient heat transfer tests were conducted for Reynolds numbers of one-fourth, one-half, and equal to the operating Reynolds number for the NASA Turbine. Tests were conducted for stationary and rotating conditions with rotation numbers in the range occurring in the NASA Turbine. Results from the experiments showed the heat transfer characteristics within the coolant passage were affected by rotation. In general, the heat transfer increased and decreased on the sides of the straight radial passages with rotation as previously reported from NASA-HOST-sponsored experiments. The heat transfer in the tri-passage axial flow region adjacent to the blade exit was relatively unaffected by rotation. However, the heat transfer on one surface, in the transitional region between the radial inflow passage and axial, constant radius passages, decreased to approximately 20 percent of the values without rotation. Comparisons with previous 3-D numerical studies indicated regions where the heat transfer characteristics agreed and disagreed with the present experiment.

Johnson, B. V.↗
NASA NTRS1997

Tetrahedral and Hexahedral Mesh Adaptation for CFD Problems

This paper presents two unstructured mesh adaptation schemes for problems in computational fluid dynamics. The procedures allow localized grid refinement and coarsening to efficiently capture aerodynamic flow features of interest. The first procedure is for purely tetrahedral grids; unfortunately, repeated anisotropic adaptation may significantly deteriorate the quality of the mesh. Hexahedral elements, on the other hand, can be subdivided anisotropically without mesh quality problems. Furthermore, hexahedral meshes yield more accurate solutions than their tetrahedral counterparts for the same number of edges. Both the tetrahedral and hexahedral mesh adaptation procedures use edge-based data structures that facilitate efficient subdivision by allowing individual edges to be marked for refinement or coarsening. However, for hexahedral adaptation, pyramids, prisms, and tetrahedra are used as buffer elements between refined and unrefined regions to eliminate hanging vertices. Computational results indicate that the hexahedral adaptation procedure is a viable alternative to adaptive tetrahedral schemes.

Biswas, Rupak↗
NASA NTRS2015

Cryogenic Orbital Testbed (CRYOTE) Ground Test Article, Final Report

Liquid propulsion has been used since Robert Goddard started developing a liquid oxygen (LO2) and gasoline powered rocket and fired it in 1923 (Ref. 1). In the following decades engineers settled on the combination of liquid hydrogen (LH2) and LO2 as the most efficient propellant combination for in-space travel. Due to their low temperatures (LH2 at 20 K and LO2 at 90 K), they require special handling and procedures. General Dynamics began developing LO2 and LH2 upper stages in 1956 in the form of Centaur, these efforts were soon funded by the Department of Defense in conjunction with NASA (beginning in 1958) (Ref. 2). Meanwhile NASA also worked with McDonnell Douglas to develop the SIV-B stage for the Saturn V rocket. In the subsequent years, the engineers were able to push the Centaur to up to 9 hr of orbital lifetime and the SIV-B to up to 6 hr. Due to venting the resultant boil-off from the high heat loads through the foam insulation on the upper stages, both vehicles remained in a settled configuration throughout the flights, thus the two phases of propellant (liquid and vapor) were separated at a known location. The one exception to this were the Titan/Centaur missions, which thanks to the lower boil-off using three layers of multilayer insulation (MLI), were able to coast unsettled for up to 5.25 hr during direct geosynchronous orbit insertion missions. In the years since there has been a continuous effort to extend the life of these upper stages from hours to days or even months.

Joule-Thompson Effect↗
NASA NTRS1989

Modal selection in structural dynamics

An overview of two modal selection procedures for lightly damped structural dynamic models is presented. Both procedures order the modes in terms of their contribution to the input/output dynamics of the model. A complex model of the Phase I Space Station is used to illustrate the application of these procedures to a realistic structure.

Blelloch, Paul A.↗
NASA NTRS1986

An analytical treatment of discretely varying constraints and inertial properties in multi-body dynamics

A computerized procedure is presented for calculating instantaneous velocity changes due to discrete imposition of constraints, impact or discrete inertial changes. Such discrete changes are impulsive in nature, involve wave propagation and therefore usually require detailed modeling for accurate prediction. It is demonstrated that when modeling is coarse, physically unrealistic results can be produced. The present procedure, which concentrates on finite element analysis, reduces the need for detailed modeling by assuming that only those velocities in the neighborhood of grid points involved in the constraint or those rigidly connected to grid points involved in the constraint need be considered in calculating velocity changes. The procedure utilizes Newton's second law and as such conserves momentum where valid. Sample problems are provided.

Housner, J. M.↗
NASA NTRS1997

Enhanced Multiobjective Optimization Technique for Comprehensive Aerospace Design

A multidisciplinary design optimization procedure which couples formal multiobjectives based techniques and complex analysis procedures (such as computational fluid dynamics (CFD) codes) developed. The procedure has been demonstrated on a specific high speed flow application involving aerodynamics and acoustics (sonic boom minimization). In order to account for multiple design objectives arising from complex performance requirements, multiobjective formulation techniques are used to formulate the optimization problem. Techniques to enhance the existing Kreisselmeier-Steinhauser (K-S) function multiobjective formulation approach have been developed. The K-S function procedure used in the proposed work transforms a constrained multiple objective functions problem into an unconstrained problem which then is solved using the Broyden-Fletcher-Goldfarb-Shanno (BFGS) algorithm. Weight factors are introduced during the transformation process to each objective function. This enhanced procedure will provide the designer the capability to emphasize specific design objectives during the optimization process. The demonstration of the procedure utilizes a computational Fluid dynamics (CFD) code which solves the three-dimensional parabolized Navier-Stokes (PNS) equations for the flow field along with an appropriate sonic boom evaluation procedure thus introducing both aerodynamic performance as well as sonic boom as the design objectives to be optimized simultaneously. Sensitivity analysis is performed using a discrete differentiation approach. An approximation technique has been used within the optimizer to improve the overall computational efficiency of the procedure in order to make it suitable for design applications in an industrial setting.

Chattopadhyay, Aditi↗
NASA NTRS1977

Continuum models for static and dynamic analysis of repetitive lattices

A simple, rational approach is presented for developing continuum models for large repetitive lattice structures subjected to static and dynamic loadings. The procedure involves introducing kinematic assumptions to reduce the dimensionality of the lattice, and equating the strain and kinetic energies of the continuum model to those of the original lattice structure. The proposed procedure is applied to obtain effective elastic and dynamic characteristics of continuum plate models for double-layered grids. Numerical results are presented of stress and free vibration problems for two double-layered grids. These problems demonstrate the high accuracy of the continuum plate models developed. Also, an assessment is made of different approximations to these models.

Noor, A. K.↗
NASA NTRS2014

Development of Dynamic Sub-Grid Models for Variational Multiscale Methods

A dynamic Variational Multiscale Method (Hughes et al. 1998) is developed by leveraging the Germano procedure from classical Large-eddy Simulations (LES). The similarity between the classical and variational approaches is analyzed in the context of incompressible flow. This analysis leads to a consistent modeling approach for both incompressible and compressible flows, the latter being demonstrated in a priori testing for low-speed attached and separated boundary layers. Similar to the classical LES procedure from which it is derived, the variational dynamic procedure does not guarantee a positive semi-definite coefficient in the general case. However, reproducing the behavior of the classical LES dynamic approach is seen as a necessary first step to develop a VMM that automatically adjusts to the local resolution and flow physics.

Variational multiscale↗
NASA NTRS1990

Development and application of a technique for reducing airframe finite element models for dynamics analysis

A computational procedure for the reduction of large finite element models was developed. This procedure is used to obtain a significantly reduced model while retaining the essential global dynamic characteristics of the full-size model. This reduction procedure is applied to the airframe finite element model of AH-64A Attack Helicopter. The resulting reduced model is then validated by application to a vibration reduction study.

Hashemi-Kia, Mostafa↗