SEARCH · Engineering Papers

Results for “Ductility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

NASA NTRS1987

The role of boron in ductilizing Ni3Al

Ductilization of Ni3Al at room temperature by microalloying with boron has been primarily attributed to the increased grain boundary cohesion in the presence of boron. However, another aspect of the role played by boron in ductilizing Ni3Al is revealed when the Hall-Petch relationships for Ni3Al and B-doped Ni3Al are compared. A shallower slope for the B-doped Ni3Al compared to that for Ni3Al indicates a reduced resistance to slip propagation across grain boundaries, and therefore reduced stress concentration at boundaries, in the presence of boron. This comparison of Hall-Petch relationships was carried out by generating data for powder processed B-doped Ni3Al at various grain sizes and by compiling data for Ni3Al from the literature. In addition, the room temperature fracture of B-doped Ni3Al has been shown to initiate along certain grain boundaries. The fracture eventually occurs by transgranular ductile tearing.

Vedula, K.↗

NASA NTRS1989

The effect of anti-phase domain size on the ductility of a rapidly solidified Ni3Al-Cr alloy

Tensile tests on splat-quenched Ni3Al-Cr alloys showed a sharp decrease in ductility with long-time annealing. The growth of the initially very-fine-size anti-phase domains showed a tenuous correlation with ductility up to a critical size, where ductility was lost. The grain size was relatively unaffected by these annealing treatments, but the grain-boundary curvature decreased, implying less toughness. An important observation was that, for the longest annealing time, a chromium-rich precipitate formed, which the data indicate could be a boride. Miniaturized tensile tests were performed on samples which were all obtained from the same splat-quenched foil, and the various domain sizes were controlled by subsequent annealing treatments.

Carro, G.↗

NASA NTRS1992

Improving the low temperature ductility of NiAl

The intermetallic NiAl exhibits excellent potential as a structural material for application in air-breathing and single-stage-to-orbit engines. Unfortunately NiAl is brittle at ambient temperature, which is partly attributed to the lack of five independent slip systems as required by von Mises criterion for uniform, volume conserving deformation since the operative group of zone axes (100) slip offers only three independent slip systems. Isostructural FeAl, however, deforms by group of zone axes (111) slip at room temperature which provides five independent slip systems. Thus, it was decided to macroalloy NiAl with Fe to promote group of zone axes (111) slip thereby possibly improving the ductility. For Ni - 30 at. (percent) Al - 20 at. (percent) Fe having essentially bcc microstructure indicated up to 6 percent tensile elongation combined with high yield strength (about 800 MPa). The results compare favorably with those of stoichiometric Ni - 50 at. (percent) Al which, however, deforms by group of zone axes (100) slip at room temperature. The multi-phase alloy approach has proven even more successful for Ni - 20 at. (percent) Al - 30 at. (percent) Fe. The high temperature ductility of the multi-phase alloy was attributed to deformation transfer across interphase boundaries and the crack stopping action of the constituent gamma/gamma' phase. While the constituent phase became increasingly brittle, the beta' phase became more ductile at elevated temperatures. Thus the multi-phase alloy did not exhibit any elevated temperature embrittlement. Similarly, while the beta' phase became weak at high temperatures, the gamma/gamma' phase exhibited better strength retention leading to the improved elevated temperature strength of the multi-phase alloy. Thus, the multi-phase alloy benefits from both its constituent phases, with each phase alleviating the disadvantages associated with the other phase over any temperature range. The multi-phase alloy approach is suggested as a possible approach to designing intermetallic-based alloys.

Guha, Sumit↗

NASA NTRS1994

The Relationship Between Constraint and Ductile Fracture Initiation as Defined by Micromechanical Analyses

The use of small laboratory specimens to predict the integrity of large, complex structures relies on the validity of single parameter fracture mechanics. Unfortunately, the constraint loss associated with large scale yielding, whether in a laboratory specimen because of its small size or in a structure because it contains shallow flaws loaded in tension, can cause the breakdown of classical fracture mechanics and the loss of transferability of critical, global fracture parameters. Although the issue of constraint loss can be eliminated by testing actual structural configurations, such an approach can be prohibitively costly. Hence, a methodology that can correct global fracture parameters for constraint effects is desirable. This research uses micromechanical analyses to define the relationship between global, ductile fracture initiation parameters and constraint in two specimen geometries (SECT and SECB with varying a/w ratios) and one structural geometry (circumferentially cracked pipe). Two local fracture criteria corresponding to ductile fracture micromechanisms are evaluated: a constraint-modified, critical strain criterion for void coalescence proposed by Hancock and Cowling and a critical void ratio criterion for void growth based on the Rice and Tracey model. Crack initiation is assumed to occur when the critical value in each case is reached over some critical length. The primary material of interest is A516-70, a high-hardening pressure vessel steel sensitive to constraint; however, a low-hardening structural steel that is less sensitive to constraint is also being studied. Critical values of local fracture parameters are obtained by numerical analysis and experimental testing of circumferentially notched tensile specimens of varying constraint (e.g., notch radius). These parameters are then used in conjunction with large strain, large deformation, two- and three-dimensional finite element analyses of the geometries listed above to predict crack initiation loads and to calculate the associated (critical) global fracture parameters. The loads are verified experimentally, and microscopy is used to measure pre-crack length, crack tip opening displacement (CTOD), and the amount of stable crack growth. Results for A516-70 steel indicate that the constraint-modified, critical strain criterion with a critical length approximately equal to the grain size (0.0025 inch) provides accurate predictions of crack initiation. The critical void growth criterion is shown to considerably underpredict crack initiation loads with the same critical length. The relationship between the critical value of the J-integral for ductile crack initiation and crack depth for SECT and SECB specimens has been determined using the constraint-modified, critical strain criterion, demonstrating that this micromechanical model can be used to correct in-plane constraint effects due to crack depth and bending vs. tension loading. Finally, the relationship developed for the SECT specimens is used to predict the behavior of circumferentially cracked pipe specimens.

Panontin, Tina L.↗

DOE OSTI2023

Behavior and properties of helium cavities in ductile-phase-toughened tungsten irradiated with He + ions at an elevated temperature

Ductile-phase toughened tungsten (DPT W) composites have demonstrated a great potential for plasma-facing components in fusion power systems. These materials can retain the outstanding thermomechanical properties of W while significantly enhancing the fracture toughness. The DPT W composite in this study consists of W particles (88 wt.%) embedded in a ductile NiFeW (12 wt.%) solution matrix. Irradiation of the composite was performed with 90 keV He + ions to 1.0 × 10 17 He + /cm 2 at 973 K. The He cavities formed in both W and NiFeW phases are examined using convergent-beam scanning transmission electron microscopy (CB-STEM) at an atomic-level resolution. Full-range depth profiles of the He cavity diameters and number densities are analyzed. The results show that the average cavity diameter in NiFeW is ~2.7 times that in W, while the number density is an order of magnitude lower. A quantitative analysis of the He density and pressure in the cavities is also achieved using STEM electron energy loss spectroscopy (STEM-EELS) mapping. The He atoms in the cavities in NiFeW are found to be under-pressurized, while those in similar-sized cavities in W are not detectable. Further, the He energy-loss shift exhibits a linear relationship with the He density in cavities in NiFeW, with the slope comparable to that for martensitic steel.

36 MATERIALS SCIENCE↗

DOE OSTI2021

A variational phase-field model For ductile fracture with coalescence dissipation

A novel phase-field model for ductile fracture is presented. The model is developed within a consistent variational framework in the context of finite-deformation kinematics. A novel coalescence dissipation introduces a new coupling mechanism between plasticity and fracture by degrading the fracture toughness as the equivalent plastic strain increases. The proposed model is compared with a recent alternative where plasticity and fracture are strongly coupled. Several representative numerical examples motivate specific modeling choices. In particular, a linear crack geometric function provides an “unperturbed” ductile response prior to crack initiation, and Lorentz-type degradation functions ensure that the critical fracture strength remains independent of the phase-field regularization length. In addition, the response of the model is demonstrated to converge with a vanishing phase-field regularization length. Additionally, the model is then applied to calibrate and simulate a three-point bending experiment of an aluminum alloy specimen with a complex geometry. The effect of the proposed coalescence dissipation coupling on simulations of the experiment is first investigated in a two-dimensional plane strain setting. The calibrated model is then applied to a three-dimensional calculation, where the calculated load-deflection curves and the crack trajectory show excellent agreement with experimental observations. Finally, the model is applied to simulate crack nucleation and growth in a specimen from a recent Sandia Fracture Challenge.

42 ENGINEERING↗

DOE OSTI2026

Ultra-grain refinement creates FCC pure cobalt with high strength and high ductility

Although pure cobalt is generally known to have a hexagonal close-packed (HCP) structure at room temperature, we show that its high-temperature face-centered cubic (FCC) phase can be strongly stabilized through grain refinement, resulting in FCC pure cobalt at room temperature. Ultrafine-grained (UFG) FCC cobalt exhibits a hierarchical microstructure consisting of dense stacking fault (SF) networks in the dominant FCC grains and numerous SFs and thin FCC layers within a few HCP plates. This unique microstructure leads to a high tensile strength exceeding 1 GPa, together with a tensile elongation of over 35%, thereby surpassing the well-known strength–ductility trade-off of pure metals. In-situ synchrotron X-ray diffraction revealed that the UFG FCC cobalt exhibited a markedly enhanced deformation-induced FCC→HCP martensitic transformation, which provided sustained strain hardening through the transformation-induced plasticity (TRIP) effect. Furthermore, ultra-grain refinement dramatically suppressed premature void and crack formation, causing a transition in the fracture mode from brittle to ductile. These findings advance the fundamental understanding of the phase stability and TRIP-assisted deformation in elemental cobalt and offer new guidelines for the microstructure-driven design of high-performance cobalt-based structural alloys.

Metastability↗

DOE OSTI2023

Machine learning based approach to predict ductile damage model parameters for polycrystalline metals

Damage models for ductile materials typically need to be parameterized, often with the appropriate parameters changing for a given material depending on the loading conditions. This can make parameterizing these models computationally expensive, since an inverse problem must be solved for each loading condition. Using standard inverse modeling techniques typically requires hundreds or thousands of high-fidelity computer simulations to estimate the optimal parameters. Additionally, the time of a human expert is required to set up the inverse model. Machine learning has recently emerged as an alternative approach to inverse modeling in these settings, where the machine learning model is trained in an offline manner and new parameters can be quickly generated on the fly, after training is complete. Here, this work utilizes such a workflow to enable the rapid parameterization of a ductile damage model called TEPLA with a machine learning inverse model. The machine learning model can efficiently estimate the model parameters much faster, as compared to previously employed methods, such as Bayesian calibration. The results demonstrate good accuracy on a synthetic test dataset and is validated against experimental data.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Predicting ductility of Mg/SiCp nanocomposite under multiaxial loading conditions based on unit cell modeling

This article presents an investigation on the ductility of Mg/SiCp under nine different multiaxial loading conditions based on a unit cell (or called representative volumetric element, RVE) finite element model. The constitutive relationship of magnesium matrix is characterized by a model combined Lode angle dependent plasticity model with the CPB06 plasticity model, which is able to describe the tension-compression asymmetry in magnesium matrix. The debonding of the matrix-particle interface and matrix fracture are considered by the modified Mohr-Coulomb (MMC) fracture model. Simulation results show that the interface debonding and subsequent matrix fracture are responsible for the ductility and fracture of nanocomposite. The computational results with parametric studies are compared and well correlated with experimental data, and it finally gives a stress-based full fracture locus of Mg/SiCp nanocomposite.

42 ENGINEERING↗

DOE OSTI2020

Tailoring ductile-phase toughened tungsten hierarchical microstructures for plasma-facing materials

Biological materials, such as bones, nacre, etc., have been found to show attractive and unique combinations of stiffness, strength and fracture toughness. Research has been conducted in various engineering areas to mimic the naturally hierarchical microstructures or nanostructures of these materials to produce materials with optimum stiffness, high strength and fracture toughness for their intended structural applications. In the same objective, this work applies a multiscale microstructural approach recently developed to investigate the deformation and fracture behavior of ductile phase toughened tungsten (W) materials such as tungsten-nickel/iron (W-Ni/Fe) composites that possess lamellar-like and hierarchical “brick-and-mortar” (BAM) microstructures. First, the approach is used to simulate tensile loading of W-Ni/Fe specimens cut out from hot-rolled W-Ni/Fe plates which possess lamellar-like microstructures. The finite element model of the gage section of the specimen consists of a W-Ni/Fe dual-phase microstructural domain in which the constitutive behaviors of W and Ni/Fe phases are described by an elastic-plastic damage model. The predicted material stress-strain response and crack pattern development as a function of loading are then compared to the corresponding experimental results to determine the constitutive model parameters for W and Ni/Fe. Subsequently, the model parameters are used to analyze W-Ni/Fe BAM microstructures that are artificially created to investigate the effects of microstructural features and morphologies on the composite stress-strain response, damage, and fracture patterns. The modeling shows that regular BAM microstructures that experience bridging mechanism combined with crack penetration across W-phase regions exhibit significantly higher strengths than the rather random lamellar-like microstructures. More significantly, however adjusting the brick’s length-to-height ratio, the BAM microstructure can be designed to allow a more distributed damage zone which leads to increased strength, ductility and fracture energy.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Behavior of helium cavities in ion-irradiated W-Ni-Fe ductile-phase toughened tungsten

This study reports on the distribution of helium (He) cavities in a hot-rolled W-Ni-Fe ductile-phase toughened tungsten (DPT W) composite irradiated to a dose and a helium concentration that are comparable to those in the material after 5-year irradiation in a conceptual fusion power plant. Here, the DPT W sample consists of W particles embedded in a ductile-phase NiFeW matrix with a nominal composition of 90W-7Ni-3Fe by weight. It was hot-rolled to a thickness reduction by 87% (87R DPT W). Sequential irradiation of the material with 1.2 MeV Ni + ions to a fluence of 2.15×10 16 Ni + /cm 2 and 90 keV He + ions to 6.5×10 15 He + /cm 2 was performed at 973 K. Larger He cavities with a lower number density are observed in NiFeW than W. Helium cavities are aggregated preferentially along the NiFeW/W interphase boundary. This behavior is not observed along the W/W grain boundary under the same irradiation conditions. A similar distribution of He cavities with comparable sizes is observed in 87R DPT W irradiated with He + ions only, suggesting that the He cavity distribution is not significantly affected by pre-irradiation of Ni + ions at 973 K. The data from this study does not provide any evidence for formation of visible voids or Ni precipitates in W phase irradiated with Ni + ions only. Diffusion and clustering of He atoms and mobile vacancies during ion irradiation at 973 K are responsible for the formation and growth of the He cavities.

36 MATERIALS SCIENCE↗

DOE OSTI2025

On the bulk compaction of brittle granular materials, Part III: Brittle‐to‐ductile transition and yield strength

A new and simple method is presented that enables the estimation of the yield strength (σ y ) of brittle materials (e.g., ceramics, glasses). It results from the combination of sufficiently high-stress compaction of their granular form, postmortem analysis of the crushed particles to identify the critical particle size corresponding to their brittle-to-ductile transition, and the use of a developed and simple analytical expression. Here, this method was an outcome from Part I of this three-paper series. To execute it, a granular brittle material is compacted to a sufficiently high stress, whereby the acting comminution produces both a fraction of particles having a sufficiently small size formed by ductile or plastic-like deformation and a remaining fraction of larger particles formed from brittle fracture. Postmortem microscopy is then used to identify the smallest particle size whose morphology indicates it formed from brittle fracture (d B2D ). The brittle material's σ y can then be estimated using a combination of the d B2D , Kendall's and Griffith's theories, a priori knowledge of the material's fracture toughness (K Ic ), and a fracture mechanics shape factor constant (Y) using σ y = √((32 π K Ic 2 )/(3 Y 2 d B2D )). The method's development and its use to estimate σ y for several vitreous silicates, α-quartzes, and NaCl are provided.

Compaction↗

DOE OSTI2023

Improving the Fracture Toughness and Ductility of Liquid-Phase Sintered WNiFe Tungsten Heavy Alloys by High-Temperature Annealing

Tungsten heavy alloys (WHAs) are candidates for use in fusion reactor divertors. Here, we characterize liquid-phase sintered WHAs with 90, 92.5, 95, and 97 (wt.%) tungsten (W), with a balance of a 0.7Ni–0.3Fe ductile phase. These WHAs show remarkable room temperature (RT) fracture toughness at the maximum load, K Jm , ranging from ≈ 38 to 107 MPa√m, compared to a monolithic W toughness of ≈ 8 MPa√m. In most cases, the fracture of WHAs occurs through stable crack tearing. However, the 97W WHA has the lowest toughness and fracture elastically in all but the smallest specimens. As lower Ni contents are desirable for fusion application, we explore the potential for improving the ductility and K Jm of WHAs using vacuum annealing at 1300 °C for 24 h. The microstructural observations reveal negligible changes in the WHA microstructure and constituent compositions. While annealing reduces the Vickers microhardness (HV), it does not significantly change the RT yield (σ y ) and ultimate (σ u ) strengths but results in beneficial increases in total elongation in the 95 and 97W WHAs by a factor of 2. RT tests on the precracked three-point-bend (3PB) bars show that annealing increases the K Jm of these WHAs, and in the case of the 97W WHA, the increase is from 42 to 92%, depending on the size of the specimen. Toughening is due to enhanced crack tip process zone microcracking and dilatation.

36 MATERIALS SCIENCE↗

NASA NTRS2013

A Study of Solder Alloy Ductility for Cryogenic Applications

For aerospace applications it is important to understand the mechanical performance of components at the extreme temperature conditions seen in service. For solder alloys used in microelectronics, cryogenic temperatures can prove problematic. At low temperatures Sn-based solders undergo a ductile to brittle transition that leads to brittle cracks, which can result in catastrophic failure of electronic components, assemblies and spacecraft payloads. As industrial processes begin to move away from Pb-Sn solder, it is even more critical to characterize the behavior of alternative Sn-based solders. Here we report on initial investigations using a modified Charpy test apparatus to characterize the ductile to brittle transformation temperature of nine different solder systems.

solders↗

NASA NTRS2021

5 Inch Thick 2219-T87 Plate Low Ductility Investigation - Material Analysis on Broken 2219 Tensile Samples

2219-T87 material used on a LOX tank baffle support on Artemis-I showed unusually low fracture elongation. Recent material data indicated 5” thick 2219-T87 plate stock had very low ductility (<1%) in the short transverse direction at the half-thickness location. Metallurgical analysis performed to understand the root cause that led to the drastic reduction in tensile ductility. The PowerPoint report details the key findings from material analysis by optical and scanning electron microscopy.

aluminum alloy 2219↗

DOE OSTI2024

Strong‐Yet‐Ductile Eutectic Alloys Employing Cocoon‐Like Nanometer‐Sized Dislocation Cells

Abstract Eutectic alloys (EAs) with superior fluidity are known to be the easiest to cast into high‐quality ingots, making them the alloys of choice for making large‐sized structural parts. However, conventional EAs (CEAs) have never reached strength–ductility combinations on par with the best in other alloy categories. Via thermomechanical processing of cast Ni‐32.88wt%Fe‐9.53wt%Al CEAs, a cocoon‐like nano‐meshed (as fine as 26 nm) network of dislocations (CNN‐D) is produced via recovery annealing, through the rearrangement of cold‐work‐accumulated dislocations anchored by dense pre‐existing nanoprecipitates. In lieu of traditional plasticity mechanisms, such as TWIP and TRIP, the CNN‐D is particularly effective in eutectic lamellae with alternating phases, as it instigates nanometer‐spaced planar slip bands that not only dynamically refine the microstructure but also transmit from the FCC (face‐centered‐cubic) layers into the otherwise brittle B2 layers. These additional mechanisms for strengthening and strain hardening sustain stable tensile flow, resulting in a striking elevation of both strength and ductility to outrank not only all previous CEAs, but also the state of the art—additively manufactured eutectic high‐entropy alloys. The CNN‐D thus adds a novel microstructural strategy for performance enhancement, especially for compositionally complex alloys that increasingly make use of nanoprecipitates or local chemical order.

Chemistry↗

DOE OSTI2023

Solid Phase Processing of Mg-Al-Mn-Ca for High Strength and Ductility

While rare-earth Mg alloys have remarkable properties for high strength applications, lower cost alternatives are necessary for the widespread industry use of Mg. Ca added Mg alloys have shown promise as an alternative to rare-earth alloys. Ca-based precipitates can reduce basal texture, reduce casting porosity, and increase mechanical strength. However, the accumulation of Ca-based precipitates along inter-dendritic regions can severely limit ductility. Here, we apply two solid phase processing techniques, friction stir processing and shear assisted processing and extrusion, to produce wrought microstructure sheet and extruded tubes from a cast Mg-Al-Mn-Ca alloy. Ductility of the alloy is enhanced by densification under applied force and elevated temperature, grain refinement, and refinement of (Al,Mg)-Ca based precipitate.

Garcia, David↗

DOE OSTI2023

Joining of High Strength Low Ductility AA7055 by Friction Self-piercing Rivet

High strength aluminum (Al) alloy is one of higher specific strength materials for decarbonization in transportation industries. Because of low ductility at room temperature, conventional mechanical fastening such as self-piercing riveting produces cracks at the joint. In this work, we applied friction self-piercing riveting to join Al alloy (AA) 7055. No cracks were observed in the joints because of the improved local ductility of Al alloy by the generated frictional heat during joining step. Numerical modeling of joining process was applied to guide rivet geometry design and rivet material strength. Mechanical integrity of the AA7055 joints was assessed by lap shear tensile and cross-tension testing. Metallurgical characterizations revealed solid-state bonding formed not only between the rivet and surround Al materials, but also upper and lower Al sheets at the joint interface. Both solid-state bonding and mechanical interlocking between the flared rivet and bottom AA7055 sheet were the major joint mechanisms.

Lim, Yong Chae↗