Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Driver”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Flow processes in electric discharge drivers

The performance of an electric discharge shock tube is discussed from the point of view that the conditions at the sonic station are the primary controlling variables (likewise in comparing designs), and that the analysis of the flow on either side of the sonic station should be done separately. The importance of considering mass-flow rate in matching a given driver design to the downstream flow required for a particular shock-wave speed is stressed. It is shown that a driver based on the principle of liquid injection (of H2) is superior to one based on the Ludwieg tube, because of the greater mass-flow rate and the absence of a massive diaphragm.

Baganoff, D.↗
NASA NTRS1976

Description and operating performance of a parallel-rail electric-arc system with helium driver gas for the Langley 6-inch expansion tube

A parallel-rail arc-discharge system to heat and pressurize the initial helium driver gas of the Langley 6-inch expansion tube is described. This system was designed for a 2.44-m-long driver vessel rated at 138 MPa, with a distance between rails of 20.3 cm. Electric energy was obtained from a capacitor storage system rated at 12,000 V with a maximum energy of 5 MJ. Tests were performed over a range of energy from 1.74 MJ to the maximum value. The operating experience and system performance are discussed, along with results from a limited number of expansion-tube tests with air and carbon dioxide as test gases.

Moore, J. A.↗
NASA NTRS1976

A heuristic finite-state model of the human driver in a car-following situation

An approach to modeling human driver behavior in single-lane car following which is based on a finite-state decision structure is considered. The specific strategy at each point in the decision tree was obtained from observations of typical driver behavior. The synthesis of the decision logic is based on position and velocity thresholds and four states defined by regions in the phase plane. The performance of the resulting assumed intuitively logical model was compared with actual freeway data. The match of the model to the data was optimized by adapting the model parameters using a modified PARTAN algorithm. The results indicate that the heuristic model behavior matches actual car-following performance better during deceleration and constant velocity phases than during acceleration periods.

Burnham, G. O.↗
NASA NTRS1977

Basic coaxial mass driver reference design

The reference design for a basic coaxial mass driver is developed to illustrate the principles and optimization procedures on the basis of numerical integration by programmable pocket calculators. The four inch caliber system uses a single-coil bucket and a single-phase propulsion track with discrete coils, separately energized by capacitors. An actual driver would use multiple-coil buckets and an oscillatory multi-phase drive system. Even the basic, table-top demonstration system should in principle be able to achieve accelerations in the 1,000 m/sq sec range. Current densities of the order of 25 ka/sq cm, continuously achievable only in superconductors, are carried by an ordinary aluminum bucket coil for a short period in order to demonstrate the calculated acceleration. Ultimately the system can be lengthened and provided with a magnetically levitated, superconducting bucket to study levitation dynamics under quasi-steady-state conditions, and to approach lunar escape velocity in an evacuated tube.

Kolm, H. H.↗
NASA NTRS1979

Hybrid LCD driver

Display driver for hand-held signs monitor can be configured to operate either 4 digit or, by paralleling four drivers, to operate 16 digit liquid crystal display (LCD).

Rinard, G. A.↗
NASA NTRS1978

The influence of vehicle aerodynamic and control response characteristics on driver-vehicle performance

The effects of changes in understeer, control sensitivity, and location of the lateral aerodynamic center of pressure (c.p.) of a typical passenger car on the driver's opinion and on the performance of the driver-vehicle system were studied in a moving-base driving simulator. Twelve subjects with no prior experience on the simulator and no special driving skills performed regulation tasks in the presence of both random and step wind gusts.

Alexandridis, A. A.↗
NASA NTRS1979

Overview and outline of Mass-Driver Two

An overview of the Princeton-M.I.T. second mass-driver is presented. Mass-Driver Two is a 13.1 cm caliber system which uses a two coil superconducting bucket and a two-phase in quadrature drive system. Discrete drive coils are individually energized with timing supplied by position-sensing optical detectors. Intermediate energy storage is provided by sector capacitors which are recharged every half cycle by an external power source. A vacuum environment is provided for the superconducting bucket by a 4 inch ID glass pipe with the drive coils surrounding it. Magnetic flight is generated by eddy current repulsion from six copper guide strips lining the glass pipe. The length is 2.5 meters equally divided between acceleration and deceleration sections. Nominal acceleration is 5000 m/sec per sec giving a maximum bucket velocity of 112 m/sec. Regenerative braking is used to decelerate the bucket. Current densities of 25 sq cm are achieved in the superconducting bucket coils and are maintained by a cryogenic service station.

Oneill, G. K.↗
NASA NTRS1981

Applications of a new mass-driver concept

A description of the operating principles and requirements of a novel mass-driver concept is presented. The design obtains acceleration of payload bucket coils by means of transverse focussing from strong, off-axis restoring forces that are produced by drive coils operating in a 'pull-only' mode. The concept offers the unprecedented possibility of operating high-performance mass-drivers entirely within the limitations of existing commercial switching devices, such as silicon-controlled rectifiers, spark gaps, vacuum-triggered arcs or vacuum mechanical switches. Representative applications of the concept described are: (1) a large-diameter magnetic lunar launcher for payloads having autonomous maneuvering; (2) an intermediate-diameter launcher with long operational life; and (3) a reaction engine for orbit transfer of large, massive objects.

Oneill, G. K.↗
NASA NTRS1982

Mass driver reaction engine characteristics and performance in earth orbital transfer missions

Configurations of a typical mass driver reaction engine (MDRE) are presented and its use for delivery of payloads to geosynchronous orbit (GEO) from low earth orbit (LEO) is discussed. Basic rocket equations are developed for LEO to GEO round-trip missions using a single exhaust velocity. It is shown that exhaust velocities in the 5-10 km/sec range (specific impulse of 500-1000 sec) are well suited for mass drivers, minimizing the overall cost of missions. Payload delivery rate fractions show that there is little to be gained by stretching out LEO to GEO transfer times from 90 to 180 days. It therefore pays to use the shorter trip time, approximately doubling the amount of delivered payload during any fixed time of use of the MDRE.

Snow, W. R.↗
NASA NTRS1982

Plasma properties of driver gas following interplanetary shocks observed by ISEE-3

Plasma fluid parameters calculated from solar wind and magnetic field data obtained on ISEE 3 were studied. The characteristic properties of driver gas following interplanetary shocks was determined. Of 54 shocks observed from August 1978 to February 1980, nine contained a well defined driver gas that was clearly identifiable by a discontinuous decrease in the average proton temperature across a tangential discontinuity. While helium enhancements were present in all of nine of these events, only about half of them contained simultaneous changes in the two quantities. Often the He/H ratio changed over a period of minutes. Simultaneous with the drop in proton temperature the helium and electron temperature decreased abruptly. In some cases the proton temperature depression was accompanied by a moderate increase in magnetic field magnitude with an unusually low variance and by an increase in the ratio of parallel to perpendicular temperature. The drive gas usually displayed a bidirectional flow of suprathermal solar wind electrons at higher energies.

Zwickl, R. D.↗
NASA NTRS1987

Piezoelectric Driver for Incremental Motion

Vibrating device containing two piezoelectric ceramic slabs acts as mechanical driver. Eventually substitutes for small continuous or stepping electric motors of slow to moderate speeds. Piezoelectric driver simple in construction, requires no precise dimensions, inexpensive to make, and needs no lubrication. Not damaged by stalling or overloads and safe for use in explosive atmospheres; Motion controllable in micron-size increments, and holds position when power turned off. Potential applications as positioner or mover. Used to position instrument pointers, antennas, or solar panels; to focus lenses; or operate tuners, recording instruments, or valves.

Bruman, Joseph R.↗
NASA NTRS1987

Impact Driver With Integral Sliding Hammer

Tool combines impact driver with sliding dead-blow hammer. Used for any purpose for which ordinary impact driver used; tightening fasteners or driving starter holes for drill. Tool protects user from accidental injury and surrounding equipment from damage that might occur from ordinary arm-wielded hammer. Especially useful in underwater work.

Wallace, Bilby J.↗
NASA NTRS1986

A precision, thermally-activated driver for space application

A space qualified, precision, large force, thermally-activated driver that has been developed jointly by the NASA Langley Research Center and PRC Kentron is described. The driver consists of a sealed hydraulic cylinder containing a metal bellows, a bellows plug, a coil spring, a spring retainer, and output shaft, a shaft guide, and a quantity of silicone oil. Temperature changes cause the silicone oil to expand or contract thus contracting or expanding the bellows/spring assembly thereby extending or retracting the output shaft.

Murray, Robert C.↗
NASA NTRS1986

Investigation of potential driver modules and transmission lines for a high frequency power system on the space station

The feasibility of using Series Resonant Inverter as the driver module for high frequency power system on the Space Station was assessed. The performance of the Series Resonant Inverter that was used in the testing of the single-phase, 2.0-kw resonant AC power system breadboard is summarized. The architecture is descirbed and the driver modules of the 5.0 kw AC power system breadboard are analyzed. An investigation of the various types of transmission lines is continued. Measurements of equivalent series resistor and inductor and equivalent parallel capacitors are presented. In particular, a simplified approach is utilized to describe the optimal transmission line.

Brush, Harold T.↗
NASA NTRS1989

The flight telerobotic servicer Tinman concept: System design drivers and task analysis

A study was conducted to develop a preliminary definition of the Flight Telerobotic Servicer (FTS) that could be used to understand the operational concepts and scenarios for the FTS. Called the Tinman, this design concept was also used to begin the process of establishing resources and interfaces for the FTS on Space Station Freedom, the National Space Transportation System shuttle orbiter, and the Orbital Maneuvering vehicle. Starting with an analysis of the requirements and task capabilities as stated in the Phase B study requirements document, the study identified eight major design drivers for the FTS. Each of these design drivers and their impacts on the Tinman design concept are described. Next, the planning that is currently underway for providing resources for the FTS on Space Station Freedom is discussed, including up to 2000 W of peak power, up to four color video channels, and command and data rates up to 500 kbps between the telerobot and the control station. Finally, an example is presented to show how the Tinman design concept was used to analyze task scenarios and explore the operational capabilities of the FTS. A structured methodology using a standard terminology consistent with the NASA/National Bureau of Standards Standard Reference Model for Telerobot Control System Architecture (NASREM) was developed for this analysis.

Andary, J. F.↗
NASA NTRS1989

Hybrid current driver designed for a space-borne laser transmitter

NASA Goddard is developing a free-space laser communication transmitter. Each of the 10 GaAlAs diode lasers in the transmitter must be digitally modulated by individual current drivers from a common data source. In order to fit the miniature laser header modules, a hybrid integrated laser current driver was required. The hybrid, smaller than a postage stamp, can drive 100 mA modulation current at a data rate of 200 Mbit/s NRZ.

Zimmerman, Robert K., Jr.↗