SEARCH · Engineering Papers

Results for “Drag coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

All sources NASA NTRS DOE OSTI

NASA NTRS2004

Parametric Studies of Flow Separation using Air Injection

Boundary Layer separation causes the airfoil to stall and therefore imposes dramatic performance degradation on the airfoil. In recent years, flow separation control has been one of the active research areas in the field of aerodynamics due to its promising performance improvements on the lifting device. These active flow separation control techniques include steady and unsteady air injection as well as suction on the airfoil surface etc. This paper will be focusing on the steady and unsteady air injection on the airfoil. Although wind tunnel experiments revealed that the performance improvements on the airfoil using injection techniques, the details of how the key variables such as air injection slot geometry and air injection angle etc impact the effectiveness of flow separation control via air injection has not been studied. A parametric study of both steady and unsteady air injection active flow control will be the main objective for this summer. For steady injection, the key variables include the slot geometry, orientation, spacing, air injection velocity as well as the injection angle. For unsteady injection, the injection frequency will also be investigated. Key metrics such as lift coefficient, drag coefficient, total pressure loss and total injection mass will be used to measure the effectiveness of the control technique. A design of experiments using the Box-Behnken Design is set up in order to determine how each of the variables affects each of the key metrics. Design of experiment is used so that the number of experimental runs will be at minimum and still be able to predict which variables are the key contributors to the responses. The experiments will then be conducted in the 1ft by 1ft wind tunnel according to the design of experiment settings. The data obtained from the experiments will be imported into JMP, statistical software, to generate sets of response surface equations which represent the statistical empirical model for each of the metrics as a function of the key variables. Next, the variables such as the slot geometry can be optimized using the build-in optimizer within JMP. Finally, a wind tunnel testing will be conducted using the optimized slot geometry and other key variables to verify the empirical statistical model. The long term goal for this effort is to assess the impacts of active flow control using air injection at system level as one of the task plan included in the NASAs URETI program with Georgia Institute of Technology.

Zhang, Wei↗

NASA NTRS1999

Correlation Between Geometric Similarity of Ice Shapes and the Resulting Aerodynamic Performance Degradation: A Preliminary Investigation Using WIND

Aerodynamic performance calculations were performed using WIND on ten experimental ice shapes and the corresponding ten ice shapes predicted by LEWICE 2.0. The resulting data for lift coefficient and drag coefficient are presented. The difference in aerodynamic results between the experimental ice shapes and the LEWICE ice shapes were compared to the quantitative difference in ice shape geometry presented in an earlier report. Correlations were generated to determine the geometric features which have the most effect on performance degradation. Results show that maximum lift and stall angle can be correlated to the upper horn angle and the leading edge minimum thickness. Drag coefficient can be correlated to the upper horn angle and the frequency-weighted average of the Fourier coefficients. Pitching moment correlated with the upper horn angle and to a much lesser extent to the upper and lower horn thicknesses.

Wright, William B.↗

NASA NTRS1982

Investigation of installation effects of single-engine convergent-divergent nozzles

An investigation was conducted in the Langley 16-Foot Transonic Tunnel to determine installation effects on single-engine convergent-divergent nozzles applicable to reduced-power supersonic cruise aircraft. Tests were conducted at Mach numbers from 0.50 to 1.20, at angles of attack from -3 degrees to 9 degrees, and at nozzle pressure ratios from 1.0 (jet off) to 8.0. The effects of empennage arrangement, nozzle length, a cusp fairing, and afterbody closure on total aft-end drag coefficient and component drag coefficients were investigated. Basic lift- and drag-coefficient data and external static-pressure distributions on the nozzle and afterbody are presented and discussed.

Burley, J. R., II↗

NASA NTRS1959

Investigation at Mach Numbers of 0.20 to 3.50 of a Blended Diamond Wing and Body Combination of Sonic Design but with Low Wave-Drag Increase with Increasing Mach Number

A diamond wing and body combination was designed to have an area distribution which would result in near optimum zero-lift wave-drag coefficients at a Mach number of 1.00, and decreasing wave-drag coefficient with increasing Mach number up to near sonic leading-edge conditions for the wing. The airfoil section were computed by varying their shape along with the body radii (blending process) to match the selected area distribution and the given plan form. The exposed wing section had an average maximum thickness of about 3 percent of the local chords, and the maximum thickness of the center-line chord was 5.49 percent. The wing had an aspect ratio of 2 and a leading-edge sweep of 45 deg. Test data were obtained throughout the Mach number range from 0.20 to 3.50 at Reynolds numbers based on the mean aerodynamic chord of roughly 6,000,000 to 9,000,000. The zero-lift wave-drag coefficients of the diamond model satisfied the design objectives and were equal to the low values for the Mach number 1.00 equivalent body up to the limit of the transonic tests. From the peak drag coefficient near M = 1.00 there was a gradual decrease in wave-drag coefficient up to M = 1.20. Above sonic leading-edge conditions of the wing there was a rise in the wave-drag coefficient which was attributed in part to the body contouring as well as to the wing geometry. The diamond model had good lift characteristics, in spite of the prediction from low-aspect-ratio theory that the rear half of the diamond wing would carry little lift. The experimental lift-curve slope obtained at supersonic speeds were equal to or greater than the values predicted by linear theory. Similarly the other basic aerodynamic parameters, aerodynamic center position, and maximum lift-drag ratios were satisfactorily predicted at supersonic speeds.

Holdaway, George H.↗

NASA NTRS2011

An Evaluation of Performance Metrics for High Efficiency Tube-and-Wing Aircraft Entering Service in 2030 to 2035

An analysis of basic vehicle characteristics required to meet the Fundamental Aeronautics Program s 70 percent energy consumption reduction goal for commercial airliners in the 2030 to 2035 timeframe was conducted. A total of 29 combinations of vehicle parasitic drag coefficient, vehicle induced drag coefficient, vehicle empty weight and engine Specific Fuel Consumption were used to create sized tube-and-wing vehicle models. The mission fuel burn for each of these sized vehicles was then compared to a baseline current technology vehicle. A response surface equation was generated of fuel burn reduction as a function of the four basic vehicle performance metrics, so that any values of the performance metrics up to a 50 percent reduction could be used to estimate fuel burn reduction of tube-and-wing aircraft for future studies.

Perkins, H. Douglas↗

NASA NTRS1968

Performance of a 16.6 Meter Diameter Cross Parachute in a Simulated Martian Environment

Inflation and drag characteristics of a 54.4-foot (16.6 meter) nominal-diameter cross parachute, deployed at a Mach number of 1.65 and a dynamic pressure of 12.68 lb/sq f t (607.1 N/m(exp2)), were obtained from the fourth balloon-launched flight test of the Planetary Entry Parachute Program (PEPP). After deployment, the parachute quickly inflated to a full condition, partially collapsed, and then gradually reinflated while undergoing rapid oscillations between over-inflation and under-inflation. The oscillations began while the parachute was still at supersonic speeds and continued to low subsonic speeds well below an altitude of 90,000 feet (27.4 km). These canopy instabilities produced large cyclic variations in the parachute's drag coefficient. The average value of drag coefficient was about 0.8 to 0.9 at subsonic speeds and slightly lower at supersonic speeds. These drag coefficient values were based on the actual fabric surface area of the parachute canopy. The parachute sustained minor damage consisting of two canopy tears and abrasions and tears on the riser line. It is believed that this damage did not produce a significant change in the performance of the parachute.

Lundstrom, Reginald R.↗

NASA NTRS1954

Summary of Free-Flight Zero-Lift Drag Results from Tests of 1/5-Scale Models of the Convair YF-102 and F-102A Airplanes and Several Related Small Equivalent Bodies at Mach Numbers from 0.70 to 1.46

One-fifth-scale rocket-propelled models of the Convair YF-102 and F-102A airplanes were tested to determine free-flight zero-lift drag coefficients through the transonic speed range at Reynolds numbers near those to be encountered by the full-scale airplane. Trim and duct characteristics were obtained along with measurements of total-, internal-, and base-drag coefficients. Additional zero-lift drag tests involved a series of small equivalent-body-of-revolution models which were launched to low supersonic speeds by means of a helium gun. The several small models tested corresponded to the following full-scale airplanes: basic, YF-102, 2-foot (full-scale) fuselage extension, F-102A, F-102A (relocated inlets), F-102A (faired nose), and F-102A (parabolic nose) . Equivalent-body models corresponding to the normal area distribution (derived for Mach number 1.0) of each of these airplane shapes were flown and, in addition, equivalent-body models designed to represent the YF-102 and F-102A airplanes at Mach number 1.2 were tested. External-drag coefficients obtained from the 115-scale tests ranged from 0.0094 to 0.0273 for the YF-102 model and from 0.0100 to 0.0255 for the F-102A model. Forebody external-pressure-drag coefficients (drag rise) at Mach number 1.05 of 0.0183 and 0.0134 were obtained from the 115-scale models of the YF-102 and F-102A, respectively, a 16-percent reduction for the F-102A model. Values of drag rise at Mach number 1.05 from the small equivalent-body tests were nearly the same for the basic, YF-102, and 2-foot-fuselage-extension airplane shapes. Equivalent-body tests of the YF-102 and F-102A shapes showed the latter to have about 25 percent less drag rise as compared with a 16-percent reduction illustrated by the 1/5-scale tests. Additional equivalent-body tests illustrating effects of modifications to the F-102A airplane shape shared that relocating the inlets on the fuselage or altering the nose shape to provide a smoother cross-sectional area progression reduced the drag rise by approximately 16 percent. Replacing a major portion of the nose of the F-102A equivalent-body model with one of parabolic shape resulted in about a 21-percent reduction in drag rise. The drag-rise data from the equivalent-body tests include base drag.

Wallskog, Harvey A.↗

NASA NTRS1947

Supersonic Wave Drag of Sweptback Tapered Wings at Zero Lift

On the basis of a recently developed theory for sweptback wings at supersonic velocities, equations are derived for the wave drag of sweptback tapered wings with thin symmetrical double-wedge sections at zero lift. Calculations of section wave-drag distributions and wing wave drag are presented for families of tapered plan forms. Distributions of section wave drag along the span of tapered wings are, in general, very similar in shape to those of untapered plan forms. For a given taper ratio and aspect ratio, an appreciable reduction in wing wave-drag coefficient with increased sweepback is noted for the entire range of Mach number considered. For a given sweep and taper ratio, higher aspect ratios reduce the wing wave-drag coefficient at substantially subcritical supersonic Mach numbers. At Mach numbers approaching the critical value, that is, a value equal to the secant of the sweepback angle, the plan forms of low aspect ratio have lower drag coefficients. Calculations for wings of equal root bending stress (and hence different aspect ratio) indicate that tapering the wing reduces the wing wave-drag coefficient at Mach numbers considerably less than the critical value but increases the drag coefficient at Mach numbers near the critical values. Comparisons on the basis of constant aspect ratio, however, indicate an increase of the wing wave-drag coefficient with taper at Mach numbers considerably less than the critical value and a decrease of the drag coefficient with taper at Mach numbers near the critical value.

WINGS - SWEEPBACK↗

NASA NTRS1953

Effect of Ice and Frost Formations on Drag of NACA 65(sub 1) -212 Airfoil for Various Modes of Thermal Ice Protection

The effects of primary and. runback icing and frost formations on the drag of an 8-foot-chord NACA 651-212 airfoil section were investigated over a range of angles of attack from 20 to 80 and airspeeds up to 260 miles per hour for icing conditions with liquid-water contents ranging from 0.25 to 1.4 grams per cubic meter and datum air temperatures of -30 to 30 F. The results showed that glaze-ice formations, either primary or runback, on the upper surface near the leading edge of the airfoil caused large and rapid increases in drag, especially at datum air temperatures approaching 32 F and in the presence of high rates of water catch. Ice formations at lower temperatures (rime ice) did not appreciably increase the drag coefficient over the initial (standard roughness) drag coefficient. Cyclic de-icing of the primary Ice formations on the airfoil leading-edge section permitted the drag coefficient to return almost to the bare airfoil drag value. Runback icing on the lower surface did not present a serious drag problem except when heavy spanwise ridges of runback ice occurred aft of the heatable area. Frost formations caused rapid and large increases in drag with incipient stalling of the airfoil.

Gray, V. H.↗

NASA NTRS1996

Development of a real-time transport performance optimization methodology

The practical application of real-time performance optimization is addressed (using a wide-body transport simulation) based on real-time measurements and calculation of incremental drag from forced response maneuvers. Various controller combinations can be envisioned although this study used symmetric outboard aileron and stabilizer. The approach is based on navigation instrumentation and other measurements found on state-of-the-art transports. This information is used to calculate winds and angle of attack. Thrust is estimated from a representative engine model as a function of measured variables. The lift and drag equations are then used to calculate lift and drag coefficients. An expression for drag coefficient, which is a function of parasite drag, induced drag, and aileron drag, is solved from forced excitation response data. Estimates of the parasite drag, curvature of the aileron drag variation, and minimum drag aileron position are produced. Minimum drag is then obtained by repositioning the symmetric aileron. Simulation results are also presented which evaluate the affects of measurement bias and resolution.

Gilyard, Glenn↗

NASA NTRS1960

Friction and Pressure Drag of Boundary-Layer Diverter Systems at Mach Number of 3.0

An experimental investigation was performed at a Mach number of 3.0 to determine the friction and pressure drags of a pylon and a 20 deg- and a 40 deg-included-angle wedge diverter over a range of Reynolds number. The results indicated that the measured friction drag coefficients agreed reasonably with that predicted by flat-plate theory. The pressure drag coefficients of the 20 and 40 deg wedges agreed with those presented in the literature. The total drag coefficient of the pylon and the 20 deg wedge diverter was about 0.36, based on diverter frontal area, while the drag coefficient of the 40 deg wedge was about 0.47.

Stitt, Leonard E.↗

NASA NTRS1947

Supersonic Wave Drag of Sweptback Tapered Wings at Zero Lift

On the basis of a recently developed theory for sweptback wings at supersonic velocities, equations are derived for the wave drag of sweptback tapered wings with thin symmetrical double-wedge sections at zero lift. Calculations of section wave-drag distributions and wing wave drag are presented for families of tapered plan forms. Distributions of section wave drag along the span of tapered wings are, in general, very similar in shape to those of untapered plan forms. For a given taper ratio and aspect ratio, an appreciable reduction in wing wave-drag coefficient with increased sweepback is noted for the entire range of Mach number considered. For a given sweep and taper ratio, higher aspect ratios reduce the wing wave-drag coefficient at substantially subcritical supersonic Mach numbers. At Mach numbers approaching the critical value, that is, a value equal to the secant of the sweepback angle, the plan forms of low aspect ratio have lower drag coefficients. Calculations for wings of equal root bending stress (and hence different aspect ratio) indicate that tapering the wing reduces the wing wave-drag coefficient at Mach numbers considerably less than the critical value and a decrease of the drag coefficient with taper at Mach numbers near the critical value.

Margolis, Kenneth↗

NASA NTRS1972

Flight investigation of an underwing nacelle installation of three variable-flap ejector nozzles

A modified F-106B aircraft with underwing engine nacelles was flight tested to investigate airframe installation effects on ejector nozzles. Nozzle thrust coefficients, boattail drag coefficients, and boundary layer characteristics were obtained for the three nozzles. All the nozzles were geometrically similar and had 15 deg conical boattails with juncture radii of curvature equal to 0.5 maximum nozzle diameter. The effects of boattail location relative to the wing trailing edge and the ejector to primary nozzle exit diameter ratio were investigated. Shortening the length by 0.48 nozzle diameter lowered the transonic boattail drag rise Mach number from 0.97 to 0.95. Decreasing the nozzle exit diameter, which reduced the ejector to primary nozzle exit diameter ratio from 1.30 to 1.18, increased the gross thrust coefficient 4.8 percent.

Head, V. L.↗

NASA NTRS1937

Fuselage-drag tests in the variable-density wind tunnel: streamline bodies of revolution, fineness ratio of 5

Results are presented of the drag tests of six bodies of revolution with systematically varying shapes and with a fineness ratio of 5. The forms were derived from source-sink distributions, and formulas are presented for the calculation of the pressure distribution of the forms. The tests were made in the N.A.C.A. variable-density tunnel over a range of values of Reynolds number from about 1,500,000 to 25,000,000. The results show that the bodies with the sharper noses and tails have the lowest drag coefficients, even when the drag coefficients are based on the two-thirds power of the volume. The data shows the most important single characteristic of the body form to be the tail angle, which must be fine to obtain low drag.

Abbott, Ira H↗

NASA NTRS1939

Airfoil section data obtained in the NACA variable-density tunnel as affected by support interference and other corrections

The results of an investigation of the effect of support interference on airfoil drag data obtained in the variable-density tunnel are presented. As a result of the support interference, previously published airfoil data from the variable-density tunnel have shown too large drag coefficients and too large a rate of increase of drag coefficients and too large a rate increase of drag coefficients with airfoil thickness. The practical effect of the corrections on the choice of the optimum section is briefly considered and corrected data for a selected list of airfoils are presented as a convenience to the designer. Methods of correcting published data for other airfoils are presented.

Jacobs, Eastman N↗

NASA NTRS1979

Performance evaluation of Space Shuttle SRB parachutes from air drop and scaled model wind tunnel tests

The aerodynamic performance characteristics have been determined for the Space Shuttle Solid Rocket Booster drogue, main, and pilot parachutes. The performance evaluation on the 20-degree conical ribbon parachutes is based primarily on air drop tests of full scale prototype parachutes. In addition, parametric wind tunnel tests were performed and used in parachute configuration development and preliminary performance assessments. The wind tunnel test data are compared to the drop test results and both sets of data are used to determine the predicted performance of the Solid Rocket Booster flight parachutes. Data from other drop tests of large ribbon parachutes are also compared with the Solid Rocket Booster parachute performance characteristics. Parameters assessed include full open terminal drag coefficients, reefed drag area, opening characteristics, clustering effects, and forebody interference.

Moog, R. D.↗

NASA NTRS1980

Experimental and theoretical aerodynamic characteristics of two hypersonic cruise aircraft concepts at Mach numbers of 2.96, 3.96, and 4.63

The longitudinal and lateral directional aerodynamic characteristics for two Mach 5 cruise aircraft concepts were determined for test Mach numbers of 2.96, 3.96, and 4.63. Estimates from hypersonic impact theory and first order supersonic linearized theory were compared with data to indicate the usefulness of these methods. The method which applied tangent cone empirical theory to the body and tangent wedge theory to the wings and to the horizontal and vertical tails provided the best estimates. The tangent cone empirical theory applied to all components showed poor agreement with data, and the linear theory estimates were accurate only for lift coefficient and drag coefficient at low angles of attack.

Pittman, J. L.↗

NASA NTRS1989

Airfoil profile drag increase due to acoustic excitation

A two-dimensional airfoil (NACA-0009) is subjected to high intensity pure-tone sound over a 1-5 kHz frequency range while immersed in a flow with 240 ft/sec velocity in a quiet flow facility with a Reynolds number of 3 million. Wake dynamic pressures are determined, and the momentum deficit is used to calculate a two-dimensional drag coefficient. Significant increases in drag are observed when the airfoil is subjected to high-intensity sound at critical frequencies. The increased drag is accompanied by movement of the natural transition location. When the transition is fixed by roughness at 10 percent chord, no further transition movement is observed in response to an acoustic Tollmien-Schlichting disturbance. However, a 4 percent increase in the sectional drag coefficient is noted. It is believed to be due to the sound exciting the flow near the airfoil surface (shear layer), thus causing the existing turbulence to become more intense, possess a higher mixing rate (momentum), and increase the skin friction.

Shearin, John G.↗