Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Direct energy deposition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

In situ embedment of type K sheathed thermocouples with directed energy deposition

Advanced nuclear reactor systems require new technologies for heat transfer and system monitoring. Additive manufacturing (AM) offers the design flexibility to allow in-situ sensor embedment through smart manufacturing for real-time monitoring, and performance of these systems. Here, this study focuses on experiments investigating the feasibility of in-situ sensor embedment using directed energy deposition (DED). Type K thermocouples are embedded into 316L stainless steel (SS) samples using two different configurations (e.g., exposed and embedded tips) and two designs (e.g., flush to substrate) within an AM base. Embedded sensor samples are analyzed via in-situ measurements and high-temperature performance validation tests at 350ºC and 900ºC. Temperature performance results at both temperature tests show good agreement with manufacturer specifications proving that these sensors could still capture accurate temperature readings after in-situ embedment during DED processing. An additional optimization experiment was conducted on the exposed tip configuration using a surrogate thermocouple to improve tolerances and the embedment process. Results improved tolerances, lower porosity, smaller gaps between the sensor and base, and better junction contact for the sensor. Although further optimization of this embedment strategy is necessary to improve the structural stability and tolerances within the component, this research strategy provides a proof-of-feasibility for DED embedment with commercial sheathed thermocouples. This research provides early impact on embedment of sensor for multiple materials and complex geometric components..

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2022

Mechanical behavior of bimetallic stainless steel and gray cast iron repairs via directed energy deposition additive manufacturing

The utility of gray cast iron in engine components remains tied to the mechanical performance and cost. Repair and remanufacturing of castings offer economical and sustainable benefits; however, high thermal input from traditional fusion-based welding is unable to restore the original mechanical quality owing to brittle microstructures and porosity formed in situ. Directed energy deposition (DED) is an additive manufacturing method that has received considerable interest for repairs owing to the highly controllable nature of the process. Despite this, few works have connected the effect of DED parameters on actual interfacial strength. Consequently, distinct DED parameter combinations were identified to maximize the strength and fatigue life of the repaired cast iron. Further, high speed melt pool imaging and residual stress measurements are provided to aid in the understanding of the metallurgical quality and strength seen in these structures. In general, higher scanning speeds and lower thermal gradients promoted comparable tensile strength to that of the original gray cast iron. The results presented here provide a foundation to tune in the DED process to generate the required mechanical quality as a starting point for future process advancements.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Production of mechanically-generated 316L stainless steel feedstock and its performance in directed energy deposition processing as compared to gas-atomized powder

The objective of this work is to study the feasibility of mechanically-generated feedstock for use in directed energy deposition (DED) processing. Mechanically-generated powder was created by machining 316L stainless steel bar stock followed by comminution of the resulting chips through oscillation ball milling. This methodology's production yield and processing time for the specifications of a commercially available DED system are presented along with resulting powder morphology. Performance of the mechanically-generated feedstock was compared to gas-atomized powder and evaluated based on the following figures of merit: flowability, printed part height, printed part density, and chemical compositional stability throughout processing. Mechanically-generated feedstock was created to meet deposition system requirements. Compared with gas-atomized powder, mechanically-generated powder did not flow as well through the powder-delivery system. Parts printed from mechanically-generated feedstock were generally taller than their counterparts from gas-atomized feedstock, but their densities were less predictable. As a result, chemical composition of prints using both feedstocks was within standard nominal compositions for 316L stainless steel.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Review of Computer-Aided Manufacturing (CAM) strategies for hybrid directed energy deposition

Hybrid additive manufacturing intertwines both additive and subtractive manufacturing layer by layer to digitally fabricate parts with complex geometries, improved surface finish and tight dimensional accuracies, the sum of which is difficult to obtain with any single process. Computer-Aided Manufacturing (CAM) software is required to orchestrate the machine toolpathing for both the deposition as well as the machining processes and is crucial for the successful fabrication of high quality structures. Additionally, CAM requires substantial operator input to account for challenging aspects of each fabricated structure. For example, deciding at which layer of deposition will the machining process continue to maintain access to complex cavities for finishing - internal features that would otherwise be unfinishable due to reach limitations or obstructions. Moreover, of the many commercially-available hybrid systems, each has a unique kinematic environment which can benefit from specific optimization of toolpath planning and substantial research has directly correlated toolpathing with the microstructure evolution, mechanical properties, porosity and residual stress state of the final fabricated part. This review explores the available strategies for CAM in the context of hybrid direct energy deposition, discusses the advantages and disadvantages of each and considers future CAM trends for this transformational digital manufacturing technology.

36 MATERIALS SCIENCE↗
DOE OSTI2024

GRCop-42: Comparison between laser powder bed fusion and laser powder direct energy deposition

This study involves a comparative analysis of additively manufactured GRCop-42 specimens produced using two processes: laser-powder bed fusion (L-PBF) and laser powder direct energy deposition (LP-DED). The investigation characterizes a range of material attributes, including surface topography, internal defects, microstructural features, quasi-static mechanical properties, and fractographic characteristics. The findings demonstrate that, despite the specimens being fabricated with the same base material, the resulting material properties vary significantly between the two additive manufacturing processes. As such, material properties cannot be presumed to be uniform across different manufacturing methods. Consequently, material characterization must be conducted for individual manufacturing processes based on specific parameters.

36 MATERIALS SCIENCE↗
DOE OSTI2024

High-pressure phase transitions in a laser directed energy deposited Fe-33Cu Alloy

Here, additively manufactured Fe-Cu alloys contain both equilibrium face-centered cubic (FCC) and metastable body-centered cubic (BCC) crystal structure Cu precipitates depending on their size. However, the stability of these nanoscale precipitates under extreme conditions such as high pressures has not been reported. This study investigates the phase transformations and microstructural stability of laser directed energy deposition (DED-LB) made Fe67Cu33 alloy (nominal composition in at.%) under high static pressure deformation using in-situ synchrotron X-ray diffraction under pressure, postmortem high-resolution scanning transmission electron microscopy (HR-STEM), and molecular dynamics (MD) simulations. In-situ XRD results reveal a reversible phase transformation from BCC to the hexagonal close-packed (HCP) structure in the Fe grains at an onset pressure of 16.4 GPa, significantly higher than reported in the literature for pure Fe. Although no high-pressure phase transition was observed in the FCC Cu grains through XRD, HR-STEM analysis uncovers a phase transition to the HCP structure in nanoscale metastable BCC Cu precipitates within the BCC Fe matrix. After decompression, the Fe matrix reverted back to the BCC structure with periodic lath martensite, while regions of the nanoscale BCC Cu precipitates retained the metastable HCP structure. MD simulations support the BCC → HCP transition in the embedded nanoscale coherent Cu precipitates, consistent with the classical Burgers mechanism. Thus, by leveraging in-situ XRD observation, postmortem high-resolution S/TEM microscopy, and MD simulations, this study offers profound insights into the distinctive phase transformations induced by high pressure in DED-LB Fe67Cu33 alloy, which is distinguished by its hierarchical microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Extending wire-arc directed energy deposition using non-gravity aligned (NGA) torch methods

For standard Additive Manufacturing (AM) processes, traditional path planning typically relies on a 2.5-dimensional approach. In wire-arc directed energy deposition (DED), commonly referred to as wire-arc additive manufacturing (WAAM), this 2.5D approach inherently limits final near net shape due to the stair-step effect and restricts the maximum overhang angle achievable without part degradation. To achieve better near net shape and part quality, a 3D planning approach that modulates the tool tip position and angle without process changes is demonstrated in components containing up to 105° of unsupported overhang. The experimental methods are validated with half and fully enclosed cylinder sections containing 90° of overhang. The non-gravity aligned methods are then applied to a commercial WAAM system for a composite tool mold demonstrator part. As a result, the methods developed in this paper enable expansion of WAAM system capabilities to parts containing large overhangs without compromising the net shape or material structure of the resulting parts and without the need for a part positioner.

Additive manufacturing↗
DOE OSTI2024

Wire directed energy deposition of steel-aluminum structures using cold metal transfer process

In this study, a sharp transition from 316L stainless steel to 4043 aluminum alloy was fabricated using wire directed energy deposition (DED) via the cold metal transfer (CMT) process. The CMT process with its inherently low heat input, led to a significant reduction in intermetallic thickness at the bi-metallic interface compared to blown powder DED technique reported in the literature resulting in superior properties when compared to those of dissimilar steel-aluminum welds. Thermo-kinetic modeling confirmed that the intermetallic formation is through a classical nucleation and growth mechanism, and the fraction and thickness can be controlled by adjusting CMT process parameters to kinetically arrest or minimize the intermetallic formation. These findings underscore the efficacy of CMT-based wire DED for fabrication of steel-aluminum bi-metallic structures.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Implementation of disruptive designs for gas turbine components using direct energy deposition additive manufacturing

This research aims to develop a framework for establishing the correlation between in-situ monitoring data, process parameters, and microstructure evolution in blown-powder laser-directed energy deposition (DED) additive manufacturing (AM). To achieve this, a comprehensive manufacturing framework has been developed, spanning from in-situ data acquisition, melt-pool simulation, microstructure modeling, and statistical microstructure quantification. A machine learning-based surrogate model is constructed to predict melt pool geometry directly from in-situ coaxial camera data. The surrogate model is trained using outputs from a high-fidelity melt pool simulation, which provides accurate melt pool dimension data under varying process conditions. The predicted melt pool geometry is then used as input to a microstructure model to predict microstructural features. To rigorously compare and analyze microstructures, the project introduces statistical metrics that quantify differences based on key features such as morphology and texture. Microstructures are represented using advanced statistical descriptors including angular chord length distribution, two-point spatial statistics, orientation distribution function, and global spherical harmonic. These representations are used to compute four distinct “dissimilarity scores” that quantitatively capture differences in texture and morphology. This framework is demonstrated to enable automated calibration of simulation parameters by minimizing discrepancies between simulated and target microstructures. The technology developed in this project enables direct correlation between in-situ monitoring data and resulting microstructure, paving the way for adaptive microstructure control in metal AM. This capability strengthens the connection between process parameters and final material properties, facilitating more precise and reliable material design.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High-resolution 3D strain and orientation mapping within a grain of a directed energy deposition laser additively manufactured superalloy

The industrialization of Laser Additive Manufacturing (LAM) is challenged by the undesirable microstructures and high residual stresses originating from the fast and complex solidification process. Non-destructive assessment of the mechanical performance controlling deformation patterning is therefore critical. Here, we use Dark Field X-ray Microscopy (DFXM) to map the 3D subsurface intragranular orientation and strain variations throughout a surface-breaking grain within a directed energy deposition nickel superalloy. DFXM results reveal a highly heterogenous 3D microstructure in terms of the local orientation and lattice strain. The grain comprises ≈ 5 μm-sized cells with alternating strain states, as high as 5 x10 -3 , and orientation differences <0.5°. The DFXM results are compared to Electron Backscatter Diffraction measurements of the same grain from its cut-off surface. Here, we discuss the microstructure developments during LAM, rationalising the development of the deformation patterning from the extreme thermal gradients during processing and the susceptibility for solute segregation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Time-Dependent 600 °C Post-Weld Heat Treatment Response of Laser-Wire-Directed Energy Deposited Austenitic Stainless Steel Claddings on Carbon Steel

Austenitic stainless steel overlay claddings are often used to protect nuclear reactor pressure vessels from corrosion. Arc welding processes are traditionally employed, which require a high heat input to bond the dissimilar metals, creating a large heat-affected zone and high residual stress that demands a lengthy stress-relieving post-weld heat treatment, up to 48 hours. High energy beam (e.g., laser, electron beam) directed energy deposition-based overlay cladding processes show promise for fabricating claddings with superior performance compared to arc welded ones because of their localized heat input; however, their necessity and time of post-weld heat treatment are currently unclear. In this research, we investigate the time dependence of a 600 C stress-relieving post-weld heat treatment of austenitic stainless steel clad on low carbon steel by laser-wire-directed energy deposition, comparing the microstructure and mechanical properties of the as-fabricated condition to 2-, 10-, and 48-hour heat treatment times. Diffusion simulations and microscopy show a gradual carburization of the stainless steel cladding and decarburization of the heat-affected zone/base metal. Nanoindentation testing shows up to a 1.8–2.69 embrittlement in the cladding and a 0.33 to 0.69 softening in the heat-affected zone after the 48-hour post-weld heat treatment. Tensile testing of the cladding composites reveals that increasing post-weld heat treatment time raises clad cracking susceptibility due to intergranular carbide formation and shows that laser-wire-directed energy deposition claddings may not require post-weld heat treatment.

Coating↗
DOE OSTI2025

Directed energy deposition of functionally graded V-4Cr-4Ti to Fe-9Cr transition for fusion power systems

This study proposes a graded structure via additive manufacturing for divertor and first wall blanket applications in fusion reactors. Materials were selected based on thermodynamic calculations to operate from 1100 °C at the plasma-facing level to 550 °C at the structural steel level. Conventional joining methods often lead to failures due to discrete reaction layers with significant mechanical property differences. Using laser beam-directed energy deposition (LB-DED), this study demonstrates the fabrication of a VCrTi-Gr91 steel functionally graded component through a novel process parameter optimization framework. A systematic approach included powder characterization, single-track depositions, and construction of printability maps. Near full-density specimens of each interlayer were additively manufactured, and a transition from V-based alloys to reduced activation ferritic martensitic steels was achieved. Computational material selection of interlayer alloys and thermodynamic/diffusion kinetics simulations prevented most interface incompatibilities. A brittle intermetallic formed at one interface, causing cracking, which was not predicted by current thermodynamic models. Transition alloy design approach was updated with a more recent database and a mitigation strategy has been proposed to eliminate the formation of deleterious intermetallic phases. Ultimately, LB-DED has proven effective for producing multi-material graded systems for fusion applications, with the demonstrated process parameter optimization framework applicable to various materials.

Additive manufacturing↗
DOE OSTI2022

Schmid factor crack propagation and tracking crystallographic texture markers of microstructural condition in direct energy deposition additive manufacturing of Ti-6Al-4V

Metallic additive manufacturing (AM) provides a customizable and tailorable manufacturing process for new engineering designs and technologies. The greatest challenge currently facing metallic AM is maintaining control of microstructural evolution during solidification and any solid state phase transformations during the build process. Ti-6Al-4V has been extensively surveyed in this regard, with the potential solid state and solidification microstructures explored at length. In this study, we evaluate the applicability of previously determined crystallo- graphic markers of microstructural condition observed in electron beam melting powder bed fusion (PBF-EB) builds of Ti-6Al-4V in a directed energy deposition (DED) build process. The aim of this effort is to elucidate whether or not these specific crystallographic textures are useful tools for indicating microstructural conditions in AM variants beyond PBF-EB. Parent β-Ti grain size was determined to be directly related to α-Ti textures in the DED build process, and the solid state microstructural condition could be inferred from the intensity of specific α-Ti orientations. Qualitative trends on the as-solidified β-Ti grain size were also determined to be related to the presence of a fiber texture, and proposed as a marker for as-solidified grain size in any cubic metal melted by AM. Analysis of the DED Ti-6Al-4V build also demonstrated a near complete fracture of the build volume, suspected to originate from accumulated thermal stresses in the solid state. Crack propagation was found to only appreciably occur in regions of slow cooling with large α +β colonies. Schmid factors for the basal and prismatic α-Ti systems explained the observed crack pathway, including slower bifurcation in colonies with lower Schmid factors of both slip systems. Colony morphologies and localized equiaxed β-Ti solidification were also found to originate from build pauses during production and uneven heating of the build edges during deposition. Tailoring of DED Ti-6Al-4V microstructures with the insight gained here is proposed, along with cautionary insight on preventing unplanned build pauses to maintain an informed and controlled thermal environment for microstructural control.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Laser Powder Directed Energy Deposition of Steels for Nuclear Applications

This comprehensive investigation examines the structure–property relationships in two nuclear alloy systems—Alloy 709 (A709) austenitic stainless steel and Grade 92 (G-92) ferritic/martensitic (F/M) steel—manufactured via directed energy deposition (DED) for sodium-cooled fast reactor applications. This study establishes the fundamental mechanisms for controlling microstructures for optimizing the mechanical performance of additively manufactured nuclear materials through systematic heat treatment optimization and multiscale characterization. As-deposited A709 steel develops a complex multiscale strengthening architecture consisting of a fine cellular solidification structure with diameter of 2-3 µm within10–50 µm grains, elevated dislocation densities from rapid thermal cycling, and grain boundary precipitates that activate concurrent Hall–Petch, dislocation, and precipitation hardening mechanisms to achieve exceptional properties [yield strength (YS): 603 MPa, ultimate tensile strength (UTS): 844 MPa, Vickers hardness: 220 HV] that achieve a 44% superior strength compared to that of the wrought material. Heat treatments produce different results. Solution annealing (SA) dissolves the cellular structure and reduces the hardness to 190 HV. Precipitation treatment (PT) keeps the cellular structure but adds carbides, allowing the hardness to reach 205 HV. The best approach combines both treatments (SA+PT) and creates uniform precipitate distributions with M 23 C 6 carbides at the grain boundaries and MX carbonitrides in the matrix, achieving a hardness of 195 HV. However, directional differences persist, with a 12%–15% strength variation between orientations due to the inherited layered microstructural architecture that survives aggressive heat treatment. While tensile testing at 550°C demonstrates 40%–50% thermal softening with dynamic strain aging, DED A709 steel still maintains a 71% higher YS than that of the wrought material. Ion irradiation studies (100–400 dpa) of DED A709 steel reveal progressive radiation damage with increasing void density and radiation-induced segregation causing nickel enrichment and chromium depletion, which will ultimately compromise mechanical properties. As-deposited G-92 exhibits exceptional strength (UTS: 1650–1700 MPa, 430 HV) through a complex microstructure containing both ferrite and martensite phases, a high geometrically necessary dislocation (GND) density (17.04×10 14 /m 2 ), and fine carbides. Heat treatments create distinct changes. Normalizing produces fresh martensite with the highest hardness (460 HV) and an increased GND density (20.23×10 14 /m 2 ). Tempering develops dual precipitation systems and reduces the hardness to 290 HV. The optimal approach uses sequential normalizing plus tempering, achieving balanced properties with the lowest hardness (250 HV) and a reduced GND density (11.01×10 14 /m 2 ). A processing-dependent anisotropy is observed: horizontal specimens achieve superior ductile behavior, while vertical specimens exhibit brittle failure. A tempering heat treatment successfully mitigates this anisotropic behavior by transforming the hard martensitic as-deposited structure into tempered martensite enabling both horizontal and vertical specimens to exhibit similar stress–strain characteristics with visible necking behavior. Remarkably, testing at 550°C reveals a reversal in the anisotropy, where as-deposited specimens achieve near isotropy with superior thermal stability (a 15%–20% strength reduction), while tempered specimens develop an orientation dependence with a 25%–30% strength reduction. Both alloy systems demonstrate that DED processing creates specimens with a superior strength through refined microstructural features, though with distinct strengthening mechanisms—austenitic through cellular structures and precipitates versus F/M through phase transformations and precipitates. Heat treatment optimization requires alloy-specific approaches, with A709 benefiting from controlled precipitation while G-92 requires careful phase transformation control. The results show that DED manufacturing can produce nuclear materials with exceptional performance, but directional effects and temperature-dependent behavior must be carefully considered for reactor component design and qualification.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

High-throughput, in situ imaging of multi-layer powder-blown directed energy deposition with angled nozzle

Laser metal additive manufacturing (AM) has become an increasingly popular technology due to its flexibility in geometry and materials. As one of the commercialized additive processes, powder-blown directed energy deposition (DED) has been used in multiple industries such as aerospace, automotive, medical device, etc. However, a lack of fundamental understanding remains for this process, and many opportunities for alloy development and implementation can be identified. A high-throughput, in situ DED system capable of multi-layer builds that can address these issues is presented here. In this work, implications of layer heights and energy density are investigated through an extensive process parameter sweep, showcasing the power of a high-throughput setup while also discussing multi-layer interactions.

47 OTHER INSTRUMENTATION↗
DOE OSTI2026

Effect of directed energy deposition process parameter on build quality of tantalum

Tantalum is a refractory metal used in a variety of harsh environment applications. Additive manufacturing of tantalum is limited based on its high melting point and affinity for oxygen. Directed Energy Deposition is an additive manufacturing technique with rapid deposition time and compositional flexibility within builds. Additively manufactured tantalum is susceptible to a variety of material and process-based defects. Various lack-of-fusion defects were identified resulting from excessive powder feed rates or insufficient laser power. Oxygen impurities in some samples caused cracking and increased material hardness. Precipitates were identified in the highly oxidized samples which were printed immediately after the build chamber was opened. High-density, low-defect parts were successfully produced. The effects of scan speed, laser power, and powder feed rate on density and defects were analyzed. A processing window was identified for producing high-quality parts which requires adequately high laser power and lower powder feed rate.

DED↗
NASA NTRSDate not supplied

Integral Channel Nozzles and Heat Exchangers using Additive Manufacturing Directed Energy Deposition NASA HR-1 Alloy

Heat exchangers for use in propulsion applications are very critical components because they must be efficient, compact and light and often operate with working fluids at extreme temperatures or pressures or both. Various components and systems use heat exchangers such as combustion chambers of gas turbines and internal combustion engines, fuel cells (air supply and thermal management), electric batteries (thermal management), evaporators and recuperators of waste-heat-to-power systems, and rocket engines. Even if the results are more generally applicable, the heat exchangers applications to which this study is more closely related are regeneratively cooled rocket nozzles and chambers, and repressurization systems for the launch vehicles. These components are often thin-walled and contain pressurized fluids, like propellants at cryogenic or elevated temperatures. Given that the environments that these propulsion components must endure are challenging, the manufacturing to meet these specifications often require long lead times due to specialty processes and unique tooling associated with the combined thin-wall integral channel and large-scale structures. Additive manufacturing (AM) offers programmatic advantages for reduction in processing time and cost in addition to various technical advantages, including the possibility to achieve enhanced hardware complexity targeted to superior performance, part consolidation, and the capability of processing of novel alloys. While AM is already being utilized for heat exchanger components in propulsion applications, almost all these AM components are made by means of Laser Powder Bed Fusion (L-PBF). L-PBF allows for fine features but is rather limited with respect to the overall size of the components that can be manufactured. Recent developments are maturing the Laser Powder Directed Energy Deposition (LP-DED) process which may be used, for example, to make integral channel thin-wall regeneratively-cooled rocket nozzles with diameters greater than 1 m. This paper highlights some integral channel heat exchanger demonstrator hardware applications of LP-DED, as well as the characterization of this process in combination with the use of the NASA HR-1 alloy. To properly utilize LP-DED for heat exchanger manufacturing, various aspects are being characterized such as geometry limitations, measurement of surface texture and geometric angled surfaces, surface enhancements for internal channels, and material evaluation. NASA HR-1 (FeNi-Cr) is a high strength hydrogen resistant superalloy developed for use in aerospace applications, such as heat exchangers. Some aspects and considerations about the design of heat exchangers are summarized together with data relevant to LP-DED manufacturing in combination with the NASA HR-1 alloy. Microchannels were successful deposited down to 2.54 mm and 1 mm wall thickness, wall angles of 30°, both with high reproducibility. It was also found that the areal surface roughness is highly dependent on the size of the powder feedstock used for deposition. The characterization of these LP-DED features is critical for fluid flow and heat transfer predictions as it can be exploited to enhance heat transfer at the cost of increased pressure drop.

Additive Manufacturing↗