Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Direct Fusion Drive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Experimental investigation of H-mode pedestal turbulence using a charge exchange imaging diagnostic system at DIII-D

Microtearing modes (MTMs) (ω ~ ω de k θ ρ s ~ 0.1, k r ρ s ~ 0.3 – 1.0) are predicted to cause substantial electron thermal transport in the H-mode pedestal, limiting fusion performance on high-power devices. Localized 2D measurements of low-to-intermediate wavenumber density fluctuations in the edge of DIII-D H-mode plasmas suggest the presence of temporally intermittent or ‘bursting’ MTMs during the inter-ELM cycle in the steep gradient region. These measurements are obtained using a new intermediate radial resolution multichannel Charge eXchange Imaging (CXI) diagnostic that analyzes the intensity of the CVI emission at 529 nm. The mode is peaked near ρ = 0.97 with a radial full-width half maximum of 1.5–2.0 cm and a normalized density fluctuation amplitude peak of $\frac{dn_C}{n_C}$ ~ 5%, peaking near 60 kHz in the lab frame. The mode additionally features a broad spectral width from 30 to 180 kHz and propagates in the electron diamagnetic direction in the plasma frame. CXI measurements taken during discharges with high density and current ramps provide evidence that MTMs become unstable at finite collisionality and remain at nearly the same location in ρ-space despite scanning of rational surface position. This indicates that the location of the peak in the electron diamagnetic frequency is a stronger driving force than individual rational surfaces.

DIII-D↗
DOE OSTI2024

Ultrabroad-band x-ray source using a picosecond, laser-driven plasma accelerator

An ultrabroad-band x-ray source, with photon energies from 10 keV to >1 MeV, based on a picosecond laser-driven plasma accelerator, is characterized and used to radiograph high-energy-density-science relevant targets. The measured yield of 10 12 photons/shot is reaching the necessary photon yields to radiograph, in a single shot, high areal density objects and matter under extreme conditions. By focusing a short laser pulse (120 J, 1 ps) into a gas jet, a < 100 mrad electron beam with energies up to 350 MeV and up to 70 nC of charge was produced by a combination of laser self-modulation instability and direct laser acceleration. A foil placed at the exit of the gas jet is used to convert part of the electron beam energy into x rays through inverse bremsstrahlung and/or inverse Compton scattering, generating a bright, broad-band, high-photon-energy beam. This beam is used to radiograph a gold half hohlraum with a high-density sphere inside with relevant characteristics for high-energy-density science and inertial confinement fusion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Mitigation of hot-electron preheat from the two-plasmon-decay instability using silicon-doped plastic shells in direct-drive implosions on OMEGA

Hot electrons generated by the two-plasmon-decay (TPD) instability in laser-direct-drive implosions preheat the fuel and degrade performance. The mitigation of preheat using silicon-doped ablators (i.e., preheat is reduced by a factor of 1.40 ± 0.04) while decreasing the ratio of the laser spot diameter to the target diameter (⁠R b /R t⁠ ) to mitigate cross-beam energy transfer has been demonstrated on the OMEGA laser for quarter-critical laser intensities of 4.1 x 10 14 W/cm 2 ⁠, equivalent to an incident laser intensity of 8.3 x 10 14 W/cm 2 ⁠. The silicon dopant increases the electron temperature of the ablation plasma, which raises the intensity threshold for the onset of the TPD instability. These results show that implosion designs utilizing higher drive intensities can be used to achieve higher shell velocities, which are currently inaccessible with plastic ablators due to excessive preheat.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

New systems in MOOSE

The Multiphysics Object-Oriented Simulation Environment (MOOSE) serves as a common library of classes between applications developed for advanced reactor analysis, fusion device engineering, spent fuel cask analysis, geochemistry studies, among other fields. These applications drive the development of the framework to meet their needs. Systems in MOOSE group capabilities that share a common purpose and generally common code. They can be leveraged by all downstream applications, providing extensive code re-use and shared maintenance. They facilitate the discovery by new users of the classes meeting at least partially their needs, and offer the same opportunities for customization as other systems. The addition of a new system to MOOSE opens new ways of solving or discretizing nonlinear problems, of performing distributed postprocessing, and a plethora of other needs. While new systems can be introduced in downstream applications rather than at the framework level, the framework team monitors common needs across the community and often triggers their addition. Documentation, training material, development needs can be centralized, limiting duplicated work across the community. The last three years have seen a large expansion in the capabilities of MOOSE. The supporting role of the framework in the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program has created numerous feature requests to support neutronics, thermal hydraulics, computational fluid dynamics and thermo-mechanics simulations in the Griffin, SAM, Pronghorn and Bison applications respectively. Similarly, laboratory-directed research and development (LDRD) projects in additive manufacturing, high-Reynolds flow simulations, structure optimization also necessitate an expansion of the framework capabilities. This summary reports on the new systems created in MOOSE, their design, their capabilities and some of the relevant interfaces.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Double cylinder implosion experiments at the National Ignition Facility

Here, cylindrical implosion experiments are used to directly measure instability growth in a convergent geometry, providing a wealth of data for model validation. Double cylinders are a natural extension of the platform and enable measurements at a classically unstable interface, the outer surface of the inner cylinder, which experiences no ablative stabilization from the laser drive. However, the utility of this platform relies upon maintaining adequate axial uniformity of the inner cylinder during the implosion. Although previous smaller-scale double cylinder experiments exhibited acceptable levels of axial uniformity, radiation-hydrodynamics simulations of larger-scale double cylinders predict more axial non-uniformity induced by the impedance mismatch as the shock wraps around the axial ends of the inner cylinder. A mechanism to reduce axial non-uniformity in these larger double cylinder implosions is presented, and preliminary experimental data confirms the efficacy of the selected mitigation approach.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Massive, long-lived electrostatic potentials in a rotating mirror plasma

Abstract Hot plasma is highly conductive in the direction parallel to a magnetic field. This often means that the electrical potential will be nearly constant along any given field line. When this is the case, the cross-field voltage drops in open-field-line magnetic confinement devices are limited by the tolerances of the solid materials wherever the field lines impinge on the plasma-facing components. To circumvent this voltage limitation, it is proposed to arrange large voltage drops in the interior of a device, but coexist with much smaller drops on the boundaries. To avoid prohibitively large dissipation requires both preventing substantial drift-flow shear within flux surfaces and preventing large parallel electric fields from driving large parallel currents. It is demonstrated here that both requirements can be met simultaneously, which opens up the possibility for magnetized plasma tolerating steady-state voltage drops far larger than what might be tolerated in material media.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Simulation of an inductively coupled plasma with a two-dimensional Darwin particle-in-cell code

A two-dimensional particle-in-cell code for the simulation of low-frequency electromagnetic processes in laboratory plasmas has been developed. The code uses the Darwin method omitting the electromagnetic wave propagation. The Darwin method separates the electric field into solenoidal and irrotational parts. The solenoidal electric field is calculated with a new algorithm based on the equation for the electric field vorticity. The system of linear equations in the new algorithm is readily solved using a standard iterative method. The irrotational electric field is the electrostatic field calculated with the direct implicit algorithm. The code is verified by reproducing the two-stream instability, electron electromagnetic waves, and shear Alfvén waves. The code is applied to simulate an inductively coupled plasma with the driving current flowing around the plasma region. In this simulation, a ring of dense plasma forms at the initial stage but then the density becomes maximal in the center and decays monotonically toward the walls. The skin effect is in the transitional mode between local and non-local, and the electron velocity distribution function is non-Maxwellian.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2006

A Decade of Friction Stir Welding R and D at NASA's Marshall Space Flight Center and a Glance into the Future

Welding at NASA's Marshall Space Flight Center (MSFC), Huntsville, Alabama, has taken a new direction through the last 10 years. Fusion welding processes, namely variable polarity plasma arc (VPPA) and tungsten inert gas (TIG) were once the corner stone of welding development in the Space Flight Center's welding laboratories, located in the part of MSFC know as National Center for Advanced Manufacturing (NCM). Developed specifically to support the Shuttle Program's External Tank and later International Space Station manufacturing programs, was viewed as the paragon of welding processes for joining aluminum alloys. Much has changed since 1994, however, when NASA's Jeff Ding brought the FSW process to the NASA agency. Although, at that time, FSW was little more than a "lab curiosity", NASA researchers started investigating where the FSW process would best fit NASA manufacturing programs. A laboratory FSW system was procured and the first welds were made in fall of 1995. The small initial investment NASA made into the first FSW system has certainly paid off for the NASA agency in terms of cost savings, hardware quality and notoriety. FSW is now a part of Shuttle External Tank (ET) production and the preferred weld process for the manufacturing of components for the new Crew Launch Vehicle (CLV) and Heavy Lift Launch Vehicle (HLLV) that will take this country back to the moon. It is one of the solid state welding processes being considered for on-orbit space welding and repair, and is of considerable interest for Department of Defense @OD) manufacturing programs. MSFC involvement in these and other programs makes NASA a driving force in this country's development of FSW and other solid state welding technologies. Now, a decade later, almost the entire on-going welding R&D at MSFC now focuses on FSW and other more advanced solid state welding processes.

Ding, Jeff↗
DOE OSTI2025

Numerical demonstration of Biermann-generated magnetic fields in a laser-driven cylindrical implosion platform

We present two-dimensional radiation-magnetohydrodynamics FLASH simulations studying Biermann battery generated magnetic fields in a convergent geometry based on modifying an existing laser direct drive cylindrical implosion platform at Los Alamos National Laboratory. During the laser driven implosion, instabilities can arise as the target converges, and in a plasma, such instabilities can generate magnetic fields via the Biermann battery. After significant redesign (lowering the inner foam fill density, deceasing the ablator mass, and modifying the laser pulse), we demonstrate that magnetic fields reach strengths of many hundred kilogauss and persist over a nanosecond time scale. Such results pave the way for an experimental campaign for further code verification and validation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Full-wave simulations on helicon and parasitic excitation of slow waves near the edge plasma

Helicon waves are thought to be promising in various tokamaks, such as DIII-D, because they can penetrate reactor-grade high-density cores and drive the off-axis current with higher efficiency. In the frequency regime ~476 MHz, both slow electrostatic and fast electromagnetic helicon waves can coexist in DIII-D. If the antenna parasitically excites the slow mode, these waves can propagate along the magnetic field line into the scrape-off layer (SOL). Although the importance of the misalignment of the Faraday screen and the electron density in the SOL on the excitation and propagation of slow modes is well known, the conditions for minimizing slow mode excitation have yet to be optimized. Using the Petra-M simulation code in the 2D domain, we analyze the effects of the misalignment of the antenna in the poloidal direction, the misalignment of the Faraday screen in the toroidal direction, and the density in front of the antenna on slow mode generation. Our results suggest that the misalignment of the Faraday screen is a critical factor in reducing the slow mode and that the misalignment angle should be below ~5° to minimize the slow wave excitation. When the electron density is higher than 3.5 x 10 18 m –3 in the SOL, the generation of the slow mode from the antenna is minimized and unaffected by the misalignment of the Faraday screen.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

A Gaussian process based surrogate approach for the optimization of cylindrical targets

Simulating direct-drive inertial confinement experiments presents significant computational challenges, both due to the complexity of the codes required for such simulations and the substantial computational expense associated with target design studies. Machine learning models, and in particular, surrogate models, offer a solution by replacing simulation results with a simplified approximation. In this study, we apply surrogate modeling and optimization techniques that are well established in the existing literature to one-dimensional simulation data of a new cylindrical target design containing deuterium–tritium fuel. These models predict yields without the need for expensive simulations. We find that Bayesian optimization with Gaussian process surrogates enhances sampling efficiency in low-dimensional design spaces but becomes less efficient as dimensionality increases. Nonetheless, optimization routines within two-dimensional and five-dimensional design spaces can identify designs that maximize yield, while also aligning with established physical intuition. Optimization routines, which ignore constraints on hydrodynamic instability growth, are shown to lead to unstable designs in 2D, resulting in yield loss. However, routines that utilize 1D simulations and impose constraints on the in-flight aspect ratio converge on novel cylindrical target designs that are stable against hydrodynamic instability growth in 2D and achieve high yield.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Direct optimization of neoclassical ion transport in stellarator reactors

Abstract We directly optimize stellarator neoclassical ion transport while holding neoclassical electron transport at a moderate level, creating a scenario favorable for impurity expulsion and retaining good ion confinement. Traditional neoclassical stellarator optimization has focused on minimizing ϵ eff , the geometric factor that characterizes the amount of radial transport due to particles in the 1 / ν regime. Under expected reactor-relevant conditions, core electrons will be in the 1 / ν regime and core fuel ions will be in the ν regime. Traditional optimizations thus minimize electron transport and rely on the radial electric field ( E r ) that develops to confine the ions. This often results in an inward-pointing E r that drives high- Z impurities into the core, which may be troublesome in future reactors. In this work, we increase the ratio of the thermal transport coefficients L 11 e / L 11 i , which previous research has shown can create an outward-pointing E r . This effect is very beneficial for impurity expulsion. We obtain self-consistent density, temperature, and E r profiles at reactor-relevant conditions for an optimized equilibrium. This equilibrium is expected to enjoy significantly improved impurity transport properties.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Laser-driven ion and electron acceleration from near-critical density gas targets: Towards high-repetition rate operation in the 1 PW, sub-100 fs laser interaction regime

Ion acceleration from gaseous targets driven by relativistic-intensity lasers was demonstrated as early as the late 1990s, yet most of the experiments conducted to date have involved picosecond-duration, Nd:glass lasers operating at low repetition rate. Here, we present measurements on the interaction of ultraintense ( ≈ 10 20 W cm − 2 , 1 PW ) , ultrashort ( ≈ 70 fs ) Ti:Sa laser pulses with near-critical ( ≈ 10 20 cm − 3 ) helium gas jets, a debris-free targetry with the potential for future compatibility with high ( ≈ 1 Hz ) repetition rate operation. We provide evidence of α particles being forward accelerated up to ≈ 2.7 − MeV energy with a total flux of ≈ 10 11 sr − 1 as integrated over > 0.1 − MeV energies and detected within a 0.5 − mrad solid angle. We also report on on-axis emission of relativistic electrons with an exponentially decaying spectrum characterized by a ≈ 10 − MeV slope, i.e., five times larger than the standard ponderomotive scaling. The total charge of these electrons with energy above 2 MeV is estimated to be of ≈ 1 nC , corresponding to ≈ 0.1 % of the laser drive energy. In addition, we observe the formation of a plasma channel, extending longitudinally across the gas density maximum and expanding radially with time. These results are well captured by large-scale particle-in-cell simulations, which reveal that the detected fast ions most likely originate from reflection off the rapidly expanding channel walls. The latter process is predicted to yield ion energies in the MeV range, which compare well with the measurements. Finally, direct laser acceleration is shown to be the dominant mechanism behind the observed electron energization. Published by the American Physical Society 2024

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

A Zero-Emission Process for Direct Reduction of Iron by Hydrogen Plasma in a Rotary Kiln Reactor

This project’s goal was to demonstrate a hydrogen plasma (H-plasma)-rotary kiln process for reducing iron ore to iron as part of the steel manufacturing process. The H-plasma provides a greater thermodynamic driving force for reducing iron ores than thermal processes such as the DRI process, enabling lower reaction temperatures. We estimated that our process technology can reduce energy consumption by 45% compared to the blast furnace process and ~15% compared to the DRI process. Steel manufacturing produces about 1.8 tons of CO2/ton of steel with iron ore reduction accounting for about one-third of the CO2 produced in the overall manufacturing process. We estimated our process has the potential to reduce GHG emissions from ironmaking by 35% with today’s grid and by up to 88% with a future low-carbon grid while being cost competitive with the current blast furnace route. We demonstrated reduction of hematite and magnetite rich materials at temperatures from 600 to 800°C. We achieved 90-95% metallization on 100 gr samples in batch reduction experiments in the H-plasma rotary kiln furnace at 600-650°C. Attempts to perform tests in a continuous operation mode identified problems with the ore feed mechanism. We identified solutions but there was not time nor budget to correct these for this project

36 MATERIALS SCIENCE↗
DOE OSTI2026

DIII-D High Field Side Lower Hybrid Current Drive Experiment Overview

In preparation for high field side lower hybrid current drive (HFS LHCD) experiments in DIII-D, the HFS LHCD was to be commissioned and physics experiments commence once the system operated up to 300 kW for 0.5 s. The initial physics experiments sought to characterize coupling, wave propagation, and driven current measurements. In HFS LHCD first campaign, the maximum power was limited to <200 kW due to waveguide pressure leaks limiting the number of available modules and power per module. Here we summarize commissioning progress and initial physics observations. The HFS LHCD coupler was optimized for high qmin, DIII-D discharges where efficient off-axis current at r/a~0.6-0.8 is desired. The coupler n|| spectrum is peaked at 2.7 and is predicted to generate ~0.14 MA/MW coupled for 1.6 MW injected. In preparation, the HFS scrape-off layer density profile was characterized and found to have steeper profiles and lower fluctuation levels than the low field side. Furthermore, the HFS SOL density profile can be accurately predicted using global plasma quantities using machine learning. Thus far, one module has injected ~100 kW for 0.5 s with <5% reflected power. Nonthermal electrons have been observed on lower frequency channels of the electron cyclotron emission radiometer correlated with the LH power indicating core wave absorption. To avoid 30R neutral beam heat flux, a split launcher is proposed to avoid the high heat flux region while maintaining power spectrum and directivity.

Wukitch, Stephen J. [Massachusetts Inst. of Techno↗
DOE OSTI2024

The crucial role of diagnostics in achieving ignition on the National Ignition Facility (NIF)

Well over 100 diagnostics can operate on the National Ignition Facility (NIF) as a result of several decades of development on NIF, and before that on Nova, OMEGA, and earlier LLNL lasers. A subset of these have guided the approach to achieving ignition on the NIF in 2022 [H. Abu-Shawareb et al. (Indirect Drive ICF Collaboration), Phys. Rev. Lett. 129(7), 075001 (2022)]. Achieving ignition on NIF has required many types of experiments with this core set of diagnostics, some constraining known unknowns and some revealing surprises—arguably unknown unknowns. Early design work realized that the extreme precision required for ignition on NIF would require fine-tuning by experiment, that is, measuring and adjusting known unknowns. Many examples are given where the use of the core set of ignition diagnostics in experimental arrangements called platforms demonstrated control of the key theoretical parameters defined as shape, adiabat, velocity, and mix. The direction of the adjustments to input conditions is found either by trend analysis or, in many cases, by observing from the diagnostic data the direction to make an adjustment. In addition, diagnostics have revealed some unexpected or neglected known issues, which degrade performance, or unexpected issues, unknown unknowns. Some of these factors had been previously considered, but underestimated or difficult to calculate at the time. The overall methodology can be described as a variant of Popper's falsifiability philosophy [K. Popper, The Logic of Scientific Discovery (Hutchinson, 1974)]. This paper summarizes the role of ignition diagnostics in terms of falsification or validation of theory or experimental setup as well as uncovering unexpected issues. The journey to ignition started in the seventies with a 1-µm wavelength laser producing disastrous results. Diagnostics have guided us to the recent multi-decadal goal of demonstrating ignition and burn in the laboratory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRSDate not supplied

Icing Physics Studies Using the 3D SIDRM Test Article: Aerodynamic and Supercooled Liquid Icing Analysis

In-flight icing is an important safety issue and is a factor that affects aircraft design and performance. Newer regulations are driving a need for improvements in airframe and engine icing simulation capability. Experimental data is required for development of icing physics models and simulation validation. To that end, this paper presents the analysis of the supercooled liquid icing data subset from tests conducted in 2022 at the NASA Icing Research Tunnel that studied both supercooled water and ice-crystal icing. The test article that was utilized replicated 3D geometrical features of an inter-compressor duct and strut region of a turbofan engine. The surfaces of the Simulated Inter-compressor Duct Research Model (SIDRM) can be heated to simulate the warm surfaces of the turbofan inter-compressor duct. The test article is instrumented with pressure taps, heaters, heat flux gauges, and thermocouples, while a 3D laser scanner, cameras, and a scale to measure ice mass were utilized to characterize the icing behavior. The aim of these tests was to generate ice accretions on the SIDRM test article under well-characterized supercooled liquid icing and ice crystal icing conditions. This paper discusses measurements related to aerodynamic testing and supercooled liquid icing tests that were conducted. Aerodynamic measurements were analyzed and compared to computational simulations and were found to be in good agreement for the range of airspeeds (50 to 230 knots) and angles of attack (0 to 4°) tested. Various parametric sweeps were conducted during the supercooled liquid icing portion of the test entry (cloud median volumetric diameter ranged from 15 to 90 µm, total air temperature from -3 to -17 °C, angle of attack from 0 to 4°, and accretion time from 5 to 20 min). These sweeps were performed to measure that parameter’s impact on ice accretion size, location (icing extent), characteristics (such as glaze/rime ice and shedding behavior), and test article surface temperature. Analysis of the test data showed that clouds composed of larger drops, colder air temperatures, smaller angles of attack, and longer spray times were the primary parameters that resulted in accretions with greater ice mass. Test article angle of attack and cloud droplet size influenced the location of ice accretion as these two parameters directly impact collection efficiency. With respect to icing characteristics, total air temperature dictated icing type, and smaller cloud drop size along with warmer air temperatures resulted in greater amounts of ice shedding. Surface temperature increased during ice accretion from the release of latent (fusion) heat, where total air temperature and cloud drop size impacted the amount of surface temperature change. The icing measurements collected during the SIDRM tests will be used to develop and validate 3D computational engine icing tools, such as GlennICE, that predictively assesses the onset and growth of ice. One of the goals of the sponsoring NASA project is to develop simulation models and tools that can assist in the design and certification of engines for flight in icing conditions in a cost effective way.

supercooled liquid icing↗
NASA NTRSDate not supplied

Icing Physics Studies Using the 3D SIDRM Test Article: Aerodynamic and Supercooled Liquid Icing Analysis

In-flight icing is an important safety issue and is a factor that affects aircraft design and performance. Newer regulations are driving a need for improvements in airframe and engine icing simulation capability. Experimental data is required for development of icing physics models and simulation validation. To that end, this paper discusses analyzed data from icing tests conducted with a 3D test article in 2022 at the NASA Icing Research Tunnel. The test article, whose geometry is representative of an inter-compressor duct and strut region of a turbofan engine, has been designed and constructed to study the physics of supercooled water icing and ice crystal icing. The surfaces of the Simulated Inter-compressor Duct Research Model (SIDRM) can be heated to simulate the warm surfaces of the turbofan inter-compressor duct. The test article is instrumented with pressure taps, heaters, heat flux gauges, and thermocouples, while a 3D laser scanner, cameras, and a scale to measure ice mass were utilized to characterize the icing behavior. The aim of these tests was to generate ice accretions on the SIDRM test article under well-characterized supercooled liquid icing and ice crystal icing conditions. This paper discusses measurements related to aerodynamic tests and supercooled liquid icing tests that were conducted. Aerodynamic measurements were analyzed and compared to computational simulations and were found to be in good agreement for the range of airspeeds (50 to 230 knots) and angles of attack (0 to 4°) tested. Various parametric sweeps were conducted during the supercooled liquid icing portion of the test entry (cloud median volumetric diameter ranged from 15 to 90 µm, total air temperature from -3 to -17 °C, angle of attack from 0 to 4°, and accretion time from 5 to 20 min). These sweeps were performed to measure that parameter’s impact on ice accretion size, location, characteristics (such as glaze/rime ice and shedding behavior), and test article surface temperature. Analysis of the test data showed that clouds composed of larger drops, colder air temperatures, smaller angles of attack, and longer spray times were the primary parameters that resulted in accretions with greater ice mass. Test article angle of attack and cloud droplet size influenced the location of ice accretion as these two parameters directly impact collection efficiency. With respect to icing characteristics, total air temperature dictated icing type, and smaller cloud drop size along with warmer air temperatures resulted in greater amounts of ice shedding. Surface temperature increased during ice accretion from the release of latent (fusion) heat, where total air temperature and cloud drop size impacted the amount of surface temperature change. The icing measurements collected during the SIDRM tests will be used to develop and validate 3D computational engine icing tools, such as GlennICE, that predictively assesses the onset and growth of ice. One of the goals of the sponsoring NASA project is to develop simulation models and tools that can assist in the design and certification of engines for flight in icing conditions in a cost‑effective way.

supercooled liquid icing↗