Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Effect of as-cast microstructure heterogeneity on aging behavior of a high-pressure die-cast A380 alloy

Highlights: • The surface layer hardened much faster than the central region during age. • More quantity of finer precipitates was found in the surface layer during age. • The surface layer had a lower activation energy of precipitation. • Si promoted the precipitation via inducing dislocations in matrix. - Abstract: Microstructure and hardness evolution of a vacuum-assistant die-cast A380 alloy during heat treatment were investigated. Both surface layer and central region of the casting component were analyzed in die-cast state, solutionized state and artificial age state. During the artificial age, the surface layer hardened more significantly than the central region due to faster precipitation and more refined hardening phases in the surface layer. Detailed analysis on the macro-segregation, microstructure morphology and grain size revealed that the different aging behaviors exhibiting in the surface and the central region were mainly attributed to a combining effect of the enrichment of Si and Cu at the surface layer, the fully-divorced morphology of eutectic in die-cast microstructure, and the presence of the externally solidified crystals at the central region. The presence of the Si particles, which exhibited quite different thermal expansion properties, changed the density and the distribution of the dislocations in the α-Al matrix, and consequently changed the precipitation of the hardening phases.

36 MATERIALS SCIENCE↗

Interfacial structure and bonding mechanism of weld seams during porthole die extrusion of aluminum alloy profiles

Highlights: • Interfacial structures and bonding mechanisms of extrusion welds were studied. • Interfacial grain boundaries, amorphous layers and voids were found. • Bonding mechanisms in the absence/presence of a gas-pocket were proposed. • Voids closure, oxide films breaking and grain boundaries migration were discussed. - Abstract: Fine nanostructures of bonding interfaces of weld seams formed by porthole die extrusion in the absence/presence of a gas-pocket behind the bridge of the extrusion die were systematically studied to understand the underlying interfacial bonding mechanisms. Interfacial grain boundaries, nanoscale amorphous layers, and three kinds of new interfacial structures were found. Specifically, it was found that, in the absence of a gas-pocket behind the bridge, there are two distinctly different interfacial structures. For the first kind of bonding interface, interfacial grain boundaries exist in contact areas and micro-voids exist in non-contact areas. For the second kind of bonding interface, there are no interfacial grain boundaries in contact areas and only nanoscale micro-voids exist in non-contact areas. In the presence of a gas-pocket behind the bridge, nanoscale voids and amorphous layers exist at the bonding interface. It was also found that the formation of gas-pockets can be avoided by increasing the depth of the welding chamber, and the increase of the welding chamber's depth and extrusion speed also contributes to the volume reduction of micro-voids and the migration of grain boundaries at the bonding interface, so as to improve the welding quality of weld seams. Based on the experimental findings, two interfacial bonding mechanisms corresponding to the absence/presence of a gas-pocket are proposed. The specific behavior of micro-asperities contact, micro-voids closure, oxide films breaking and interfacial grain boundaries migration are described, and the solid-state bonding process during porthole die extrusion is revealed from the micro-nano scales.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Variation improvement of mechanical properties of Mg-9Al-1Zn alloy with melt conditioned high pressure die casting

Highlights: • The variation improvement of mechanical properties of AZ91D was achieved via application of high shear melt conditioning. • The elongation variation of AZ91D with MC-HPDC has a significant reduction from 31.2% for tradition HPDC to 19.7%. • High shear melt conditioning can result in grain refinement of primary α-Mg formed in both shot sleeve and die cavity. - Abstract: Melt conditioning treatment via high shearing on Mg-9Al-1Zn melt was employed to disperse the oxide inclusions, and to harness the well-dispersed particles as the effective heterogeneous nucleation sites for primary α-Mg grains during solidification in high pressure die casting. To reveal the mechanism of property improvement, Prefil pressure filtration cleanliness analyzer, field-emission scanning electron microscopy with energy dispersive X-ray spectroscopy and high-resolution transmission electron microscopy were employed in present study. The experimental results showed that the application of high shearing not only improved elongation, ultimate tensile strength and yield strength simultaneously, but also reduced the variation of the mechanical properties of Mg-9Al-1Zn alloy. The improvement was ascribed to the refinement of the primary α-Mg grains formed in both shot sleeve and die cavity, and to the reduction of porosity as well as refinement of Mg{sub 17}Al{sub 12} phases.

36 MATERIALS SCIENCE↗

Recent California tree mortality portends future increase in drought-driven forest die-off

Vegetation tolerance to drought depends on an array of site-specific environmental and plant physiological factors. This tolerance is poorly understood for many forest types despite its importance for predicting and managing vegetation stress. We analyzed the relationships between precipitation variability and forest die-off in California's Sierra Nevada and introduce a new measure of drought tolerance that emphasizes plant access to subsurface moisture buffers. We applied this metric to California's severe 2012-2015 drought, and show that it predicted the patterns of tree mortality. We then examined future climate scenarios, and found that the probability of droughts that lead to widespread die-off increases threefold by the end of the 21st century. Our analysis shows that tree mortality in the Sierra Nevada will likely accelerate in the coming decades and that forests in the Central and Northern Sierra Nevada that largely escaped mortality in 2012-2015 are vulnerable to die-off.

54 ENVIRONMENTAL SCIENCES↗

Large-Scale Metal AM for Stamping Dies

Oak Ridge National Laboratory (ORNL) worked with Dienamic Tooling Systems Group to demonstrate metal additively manufacturing stamping dies and individual details for prototype tooling. This project was completed using the Wolf Robotics metal additive manufacturing system at ORNL’s Manufacturing Demonstration Facility. A small stamping die was printed, machined, and tested; the parts formed using that die passed a quality check and were found to be in tolerance.

36 MATERIALS SCIENCE↗

Large Scale Metal Additive Manufacturing for Stamping Dies

Oak Ridge National Laboratory (ORNL) worked with Dienamic Tooling Systems (DTS) in a follow-on Phase 2 effort to develop and demonstrate additively manufactured conformal cooling for hot stamping dies, providing a new industry capability that did not previously exist. Current approaches to die cooling are nonoptimal and based on what can be machined with traditional technologies. The printed approach to hot stamping cooling channels allows an analytical needs-based size and placement approach to cooling. Cooling is optimized and parts count is reduced producing a simpler more reliable faster to manufacture stamping tool. An additively manufactured hot stamping die with conformal cooling channels was manufactured and successfully tested in a real-world environment.

36 MATERIALS SCIENCE↗

Preliminary Design of a New Pulsed-Neutron Die--Away Experiments with Absorbers (IER-552 CED-1)

This report presents the preliminary design (CED-1) of IER-552, pulsed-neutron die-away (PNDA) experiments with absorbers, to be conducted by Lawrence Livermore National Laboratory (LLNL). The goal of the PNDA experiments with absorbing materials is to produce high-quality, low-cost integral benchmarks that can be used to validate cross sections that are high priority nuclear data for the Department of Energy’s Nuclear Criticality Safety Program (NCSP). PNDA experiments can be used to generate nuclear data validation benchmarks quickly and cheaply, as they do not require fissile material or a nuclear facility to conduct them. The original PNDA experiments were set up at LLNL under IER-501. Extending the PNDA experiments to include absorbing materials leverages existing facilities and resources at LLNL to validate cross sections, with a basic experiment design that uses a neutron generator to impinge a short, mono-energetic neutron pulse on a poisoned, moderating target sample. The neutron pulse lasts 100 µs, after which the neutron population in the sample reaches thermal equilibrium and later spatial equilibrium. In this fully equilibrized state, the neutron population has a characteristic decay-time eigenvalue. The eigenvalue can be used as an integral parameter to validate nuclear data involved with neutron scattering and absorption. Two observables can be measured: the neutron population and the population of secondary γ-rays produced by inelastic and capture reactions. This report explores the feasibility of both approaches. For γ-ray measurements, this allows for direct measurement of reactions of interest for validation. During the neutron burst time, inelastic (prompt) γ-rays dominate, and these data can be isolated for validation of neutron inelastic scattering data. After the pulse ends, neutron capture (delayed) γ-rays dominate and are produced by many reaction channels as neutrons slow down to thermal energies. Two sets of γ-ray spectra (inelastic, capture) can be produced for validation. Additionally, the time-dependent decay of the capture γ-ray population when the neutron population is thermalized and in its fundamental mode can be used for validation. Two experiments can be imagined where pulsed neutrons are used to validate the nuclear data of absorbing materials. The first integrates well into the existing PNDA testbed at LLNL. The absorber material would be introduced into a moderating target and the same neutron generator, neutron detectors, electronics, and shielding box used for IER-501 would be employed. From the same experimental setup, many absorbing materials can be validated by simply changing the neutron poison in the moderator. The only significant modification would be the introduction of a γ-ray detector. Such an experiment would primarily serve to validate nuclear data in the thermal energy range. The second kind of experiment would validate the fast and epithermal energy range. It would involve pulsing neutron into a bare assembly of the absorber material and measuring the die-away of neutrons. The fast leakage of such an assembly requires nanosecond neutron-generator pulse widths and fast detectors/electronics that could measure ~200 ns die-away curves. This kind of experiment would ideally be performed at a cyclotron, like that available at Lawrence Berkeley National Laboratory.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

IER-580 CED-3b: Experiment Execution Summary for the Pulsed-Neutron Die-Away Experiments (PNDA) with H 2 O

This report summarizes new experiments performed with H 2 O for IER-580, a testbed for pulsed-neutron die-away (PNDA) experiments at Lawrence Livermore National Laboratory (LLNL). The experiments will become high-quality benchmarksthat serve to optimize and validate thermal neutron scattering laws (TSLs) of H 2 O, which are high-priority nuclear data for the Department of Energy’s Nuclear Criticality Safety Program (NCSP). The report presents the details of the measurements conducted in October of 2023, including the experimental set-up (PNDA equipment and H 2 O targets) and all experimentally measured data. The report gives the fitted decay constants for the die-away curves of each target sample. It also provides the tabulated data for the die-away curves in the appendices.

42 ENGINEERING↗

Die and telescoping punch form convolutions in thin diaphragm

Die and punch set forms convolutions in thin dished metal diaphragm without stretching the metal too thin at sharp curvatures. The die corresponds to the metal shape to be formed, and the punch consists of elements that progressively slide against one another under the restraint of a compressed-air cushion to mate with the die.

Source record↗

Neutron die-away experiment for remote analysis of the surface of the moon and the planets, phase 3

Continuing work on the two die-away measurements proposed to be made in the combined pulsed neutron experiment (CPNE) for analysis of lunar and planetary surfaces is described. This report documents research done during Phase 3. A general exposition of data analysis by the least-squares method and the related problem of the prediction of variance is given. A data analysis procedure for epithermal die-away data has been formulated. In order to facilitate the analysis, the number of independent material variables has been reduced to two: the hydrogen density and an effective oxygen density, the latter being determined uniquely from the nonhydrogeneous elemental composition. Justification for this reduction in the number of variables is based on a set of 27 new theoretical calculations. Work is described related to experimental calibration of the epithermal die-away measurement. An interim data analysis technique based solely on theoretical calculations seems to be adequate and will be used for future CPNE field tests.

Mills, W. R.↗

Development and evaluation of die materials for use in the growth of silicon ribbons by the inverted ribbon growth process, task 2, LSSA project

Silicon sessile drop experiments were performed on a variety of commercially available refractory carbides, nitrides, oxides, and borides to examine the potential of these materials for applications involving either direct contact with molten silicon or as substrates for CVD coatings in the fabrication of dies and crucibles for containing molten silicon. Simultaneous experiments were also conducted with CVD layers of SiC, Si3N4, and SiOxNy. Silicon nitride layers, deposited with NH3:SiH4 ratios ranging from 100:1 down to 5:1, were examined in sessile drop experiments to determine if the layers are degraded as a result of using lower reagent ratios. Preliminary experiments were undertaken on the stability of CVD Si3N4 near the melting point of silicon. Silicon ribbon segments were grown from vitreous carbon dies which had been coated with CVD Si3N4. Depending upon the purity of the die materials, ribbon resistivity values up to 40 Omega cm were obtained.

Duffy, M. T.↗

Contoured Orifice for Silicon-Ribbon Die

Die configuration encourages purity and stable growth. Contour of die orifice changes near ribbon edges. As result, silicon ribbon has nearly constant width and little carbon contamination. Die part of furnace being developed to produce high-quality, low-cost material for solar cells.

Mackintosh, B. H.↗

Graphite/Thermoplastic-Pultrusion Die

Attachment to extruder produces thermoplastic-impregnated graphite tape. Consists of profile die, fiber/resin collimator, and crosshead die body. Die designed to be attached to commercially available extrusion machine capable of extruding high-performance thermoplastics. Simple attachment to commercial extruder enables developers of composites to begin experimenting with large numbers of proprietary resins, fibers, and hybrid composite structures. With device, almost any possible fiber/resin combination fabricated.

Wilson, Maywood L.↗

Fissile material measurements using the differential die-away self interrogation technique

Currently, there is substantial research effort focused on quantifying plutonium (Pu) mass in spent fuel using non-destructive assay (NDA) techniques. Of the several techniques being investigated for this purpose, Differential Die-Away Self-Interrogation (DDSI) is a recently proposed, neutron-based NDA technique capable of quantifying the total fissile content in an assembly. Unlike the conventional Differential Die-Away (DDA) technique, DOSI does not require an external neutron source for sample interrogation, but rather, uses the spontaneous fission neutrons originating from {sup 244}Cm within the spent fuel for self-interrogation. The essence of the technique lies in the time separation between the detection of spontaneous fission neutrons from {sup 244}Cm and the detection of induced fission neutrons at a later time. The DDSI detector design imposes this time separation by optimizing the die-away times ({tau}) of the detector and sample interrogation regions to obtain an early and late neutron distribution respectively. The ratio of the count rates in the late gate to the early gate for singles, doubles, and triples is directly proportional to the fissile content present in the sample, which has already been demonstrated for simplified fuel cases using the Monte Carlo N-Particle eXtended (MCNPX) code. The current work applies the DDSI concept to more complex samples, specifically spent Pressurized Water Reactor (PWR) assemblies with varying isotopics resulting from a range of initial enrichment, bumup, and cooling time. We assess the feasibility of using the late gate to early gate ratio as a reliable indicator of overall fissile mass for a range of assemblies by defining a {sup 239}Pu effective mass which indicates the mass of {sup 239}Pu that would yield the same DDSI signal as the combined mass of major fissile isotopes present in the sample. This work is important for assessing the individual capability of the DDSI instrument in quantifying fissile mass in an assembly in order to use this information for a possible integration with another NDA instrument for direct Pu mass determination.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Direct Measurement of Initial Enrichment, Burn-up and Cooling Time of Spent Fuel Assembly with a Differential Die-Away Technique Based Instrument

An outline of this presentation of what a Differential Die-Away (DDA) instrument can do are: (1) Principle of operation of DDA instrument; (2) Determination of initial enrichment (IE) ({sigma} < 5%); (3) Determination of burn up (BU) ({sigma} {approx} 6%); (4) Determination of cooling time (CT) ({sigma} {approx} 20-50%); and (5) DDA instrument as a standalone device. DDA response (fresh fuel vs. spent fuel) is: (1) Fresh fuel => DDA response increases (die-away time is longer) with increasing fissile content; and (2) Spent fuel => DDA response decreases (die-away time is shorter) with higher burn-up (i.e. more neutron absorbers present).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Method of forming through substrate vias (TSVs) and singulating and releasing die having the TSVs from a mechanical support substrate

Accessing a workpiece object in semiconductor processing is disclosed. The workpiece object includes a mechanical support substrate, a release layer over the mechanical support substrate, and an integrated circuit substrate coupled over the release layer. The integrated circuit substrate includes a device layer having semiconductor devices. The method also includes etching through-substrate via (TSV) openings through the integrated circuit substrate that have buried ends at or within the release layer including using the release layer as an etch stop. TSVs are formed by introducing one or more conductive materials into the TSV openings. A die singulation trench is etched at least substantially through the integrated circuit substrate around a perimeter of an integrated circuit die. The integrated circuit die is at least substantially released from the mechanical support substrate.

36 MATERIALS SCIENCE↗