Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Current mode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Effects of edge-localized electron cyclotron current drive on edge-localized mode suppression by resonant magnetic perturbations in DIII-D

Abstract According to recent DIII-D experiments (Logan et al 2024 Nucl. Fusion 64 014003), injecting edge localized electron cyclotron current drive (ECCD) in the counter-plasma-current (counter- I p ) direction reduces the n = 3 resonant magnetic perturbation (RMP) current threshold for edge-localized mode (ELM) suppression, while co- I p ECCD during the suppressed ELM phase causes a back transition to ELMing. This paper presents nonlinear two-fluid simulations on the ECCD manipulation of edge magnetic islands induced by RMP using the TM1 code. In the presence of a magnetic island chain at the pedestal-top, co- I p ECCD is found to decrease the island width and restore the initially degraded pedestal pressure when its radial deposition location is close to the rational surface of the island. With a sufficiently strong co- I p ECCD current, the RMP-driven magnetic island can be healed, and the pedestal pressure fully recovers to its initial ELMing state. On the contrary, counter- I p ECCD is found to increase the island width and further reduce the pedestal pressure to levels significantly below the peeling-ballooning-mode limited height, leading to even stationary ELM suppression. These simulations align with the results from DIII-D experiments. However, when multiple magnetic island chains are present at the pedestal-top, the ECCD current experiences substantial broadening, and its effects on the island width and pedestal pressure become negligible. Further simulations reveal that counter- I p ECCD enhances RMP penetration by lowering the penetration threshold, with the degree of reduction proportional to the amplitude of ECCD current. For the ∼1 MW ECCD in DIII-D, the predicted decrease in the RMP penetration threshold for ELM suppression is approximately 20%, consistent with experimental observations. These simulations indicate that edge-localized ECCD can be used to either facilitate RMP-driven ELM suppression or optimize the confinement degradation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Simulation of Particulate Transport for Delivery of Solid Amendments into the Subsurface: FY24 Status Report

For particulate-based amendments to be viable for field-scale remediation at the Hanford Site (e.g., 200 DV-1 Operable Unit), particles need to be delivered a sufficient radial distance from an injection well and retained at concentrations high enough for effective treatment. An accurate description of the particle radius of influence (ROI) is critical for developing an overall remediation strategy. However, field-scale particle simulations are currently limited due to insufficient simulation capabilities and a lack of experimental data to validate and parameterize particle transport models. To help build toward field-scale deployment, this fiscal year (FY) we have (1) developed a pre screening tool to estimate particle transport, (2) implemented particle transport models within PFLOTRAN, and (3) conducted preliminary estimations of particle ROI. While field-scale numerical simulations will ultimately be necessary before remedy design and field implementation, we have developed a pre-screening tool that offers valuable estimations of expected particle injectability and ROI in a 1-D system. The advantage of the tool is that it does not require extensive laboratory experiments and instead makes predictions based solely on routine laboratory measurements. This tool can assist in down-selection and decision-making by identifying which particle amendment systems are worth pursuing in future laboratory experiments, such as 1-D column tests and beyond. With any system, scaling up from the lab to the field presents challenges. Currently, there is no field data available for model calibration or validation. However, the theoretical particle models being developed herein are the best tools available to guide progress toward field deployment. To help bridge this gap and verify model predictions, larger-scale lab experiments are being proposed. To advance simulation capabilities, six particle transport models are being integrated into the reactive transport simulator PFLOTRAN. These include colloid filtration theory (CFT) and five additional particle transport models (M1-M5). Each model, from M1 to M5, progressively incorporates additional particle transport and retention processes. Ultimately, the simplest model capable of accurately describing 1-D column data will be selected and parameterized. During FY24, the CFT and M1 model have been fully implemented within PFLOTRAN. Using an existing 1 D column experiment, the two currently implemented particle transport models (CFT and M1), and associated parameters, were fit to this experiment. While simpler model formulations are helpful for estimations, these formulations could not fully describe particle transport and retention behavior in the previous 1-D column experiment. Thus, additional complexities will need to be considered, which will be accounted for in the M2-M5 model formulations. Additionally, because a viscous, shear thinning fluid was required to keep particles in suspension, considerations for flow will also need to also be accounted for. Therefore, a new immiscible two-phase flow mode is currently being implemented in PFLOTRAN. With some modifications, this new flow module could also support simulation of non-Newtonian liquid amendments, foams, and emulsions. We also estimated the expected ROI of solid amendments using 1-D simulations. The average predicted ROI was approximately 15 ft for micron-sized zero valent iron (mZVI) suspended in xanthan gum (XG). Using the pre screening tool and ROI estimates, additional amendment-delivery laboratory characterization and experiments are proposed. The results from additional experiments can be used to validate and parametrize particulate transport model formulations, which will ultimately provide predictive capabilities for field amendment-delivery systems.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Structural changes induced by electric currents in a single crystal of Pr 2 CuO 4

We demonstrate an approach to the structural and electronic property modification of perovskites, focusing on Pr 2 CuO 4 , an undoped parent compound of a class of electron-doped copper-oxide superconductors. Currents were passed parallel or perpendicular to the copper oxygen layers with the voltage ramped up until a rapid drop in the resistivity was achieved, a process referred to as “flash.” The current was then further increased tenfold in current-control mode. This state was quenched by immersion into liquid nitrogen. Flash can drive many compounds into different atomic structures with new properties, whereas the quench freezes them into a long-lived state. Single-crystal neutron diffraction of as-grown and modified Pr 2 CuO 4 revealed a √10 ×√10 superlattice due to oxygen-vacancy order. The diffraction peak intensities of the superlattice of the modified sample were significantly enhanced relative to the pristine sample. Raman-active phonons in the modified sample were considerably sharper. Measurements of electrical resistivity, magnetization, and two-magnon Raman scattering indicate that the modification affected only the Pr-O layers, but not the Cu-O planes. These results point to enhanced oxygen-vacancy order in the modified samples well beyond what can be achieved without passing electrical current. Our work opens a new avenue toward electric field/quench control of structure and properties of layered perovskite oxides.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Al‐Rich AlGaN Transistors with Regrown p‐AlGaN Gate Layers and Ohmic Contacts

Abstract Epitaxial regrowth processes are presented for achieving Al‐rich aluminum gallium nitride (AlGaN) high electron mobility transistor (HEMTs) with p‐type gates with large, positive threshold voltage for enhancement mode operation and low resistance Ohmic contacts. Utilizing a deep gate recess etch into the channel and an epitaxial regrown p‐AlGaN gate structure, an Al 0.85 Ga 0.15 N barrier/Al 0.50 Ga 0.50 N channel HEMT with a large positive threshold voltage (V TH = +3.5 V) and negligible gate leakage is demonstrated. Epitaxial regrowth of AlGaN avoids the use of gate insulators which can suffer from charge trapping effects observed in typical dielectric layers deposited on AlGaN. Low resistance Ohmic contacts (minimum specific contact resistance = 4 × 10 −6 Ω cm 2 , average = 1.8 × 10 −4 Ω cm 2 ) are demonstrated in an Al 0.85 Ga 0.15 N barrier/Al 0.68 Ga 0.32 N channel HEMT by employing epitaxial regrowth of a heavily doped, n‐type, reverse compositionally graded epitaxial structure. The combination of low‐leakage, large positive threshold p‐gates and low resistance Ohmic contacts by the described regrowth processes provide a pathway to realizing high‐current, enhancement‐mode, Al‐rich AlGaN‐based ultra‐wide bandgap transistors.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Onset of Plasmoid Reconnection during Magnetorotational Instability

The evolution of current sheets in accretion flows undergoing magnetorotational instability (MRI) is examined through two- and three-dimensional numerical modeling of the resistive MHD equations in global cylindrical geometry. With an initial uniform magnetic field aligned in the vertical (z) direction, MRI produces radially extended toroidal (azimuthal) current sheets. In both 2D and 3D when axisymmetric modes dominate, these current sheets attract each other and merge in the poloidal (rz) plane, driving magnetic reconnection when the Lundquist number S > 3 × 10 2 , making it a possible source of plasmoids (closed magnetic loops) in accretion disks. At high Lundquist numbers in the 2D regime, starting at S = 5 × 10 3 , self-consistent MRI-generated current sheets become thin and subject to plasmoid instability, and therefore spontaneous magnetic reconnection. When nonaxisymmetric 3D modes dominate, turbulence makes the azimuthal current sheets more unstable and stretch vertically. Toroidally extended vertical current sheets in the inner region, as well as larger 3D magnetic islands in the outer regions of the disks are also formed. These findings have strong ramifications for astrophysical disks as potential sources of plasmoids that could cause local heating, particle acceleration, and high energy EM radiation.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

Phase evolution during reactive flash sintering of Li 6.25 Al 0.25 La 3 Zr 2 O 12 starting from a chemically prepared powder

Here, reactive flash sintering (RFS) of a chemically prepared multiphase precursor powder was performed to fabricate Li 6.25 Al 0.25 La 3 Zr 2 O 12 (Al-LLZO) ceramics. This approach allowed for obtaining single-phase dense samples in a remarkably short processing time of 30 s, at a furnace temperature of 600 °C, with an electric field of 50 V cm -1 and a current limit of 150 mA mm -2 . The ceramics display high bulk conductivity of 0.18 mS cm -1 at room temperature. Furthermore, phase evolution is studied by in-situ X-ray diffraction during: i) conventional heating and ii) RFS under current rate mode. As expected, the intermediate phases progressively dissolved into the Al-LLZO matrix by conventional heating. On the other hand, RFS promoted the growth of the intermediate La 2 Zr 2 O 7 , an effect that was overcome by the thermally driven formation of Al-LLZO at higher temperatures. The observed different reaction pathway suggests that RFS can be used for stabilizing phases that are not thermodynamically favored upon conventional heating.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Micro-mechanical investigation of the thermo-mechanical properties of micro-architectured tungsten coatings

The thermo-mechanical response of micro-architectured tungsten coatings is characterized in the temperature range of 293 to 673 K using both in situ micro-compression experiments inside a scanning electron microscope (SEM) as well as image-based crystal plasticity finite element method (CPFEM) simulations. The experiments were conducted on micropillar-like specimens that were focus ion beam milled into the coatings, while the simulations were conducted on columnar-grained micropillar simulation cells constructed based on the statistics of the coating’s microstructure. The experimental results show that the stress–strain response and deformation mode exhibit a strong temperature-dependence. At room temperature, catastrophic failure is observed shortly after yield and is manifested in the form of intergranular fracture and buckling of individual columnar grains. With increasing temperature, this catastrophic failure is gradually suppressed and the material exhibits a steadier strain hardening response at 693 K. The CPFEM simulations are also shown to be in good agreement with the experimental results, and these simulations indicate that the material response is strongly influenced by the local crystallographic anisotropy and microstructure inhomogeneity. Furthermore, the simulations capture the underlying mechanisms that control the temperature-dependent transition in deformation mode. The current results highlight that the micro-architectured microstructure offers a great combination of excellent mechanical strength and structural integrity at elevated temperatures, which is of importance for high temperature applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Probing the electronic structure and dipole-bound state of the 7-azaindolide anion

We report an investigation of the electronic structure and dipole-bound state (DBS) of the cryogenically-cooled 7-azaindolide anion (7-AI − ) using high-resolution photoelectron imaging, photodetachment spectroscopy, and resonant photoelectron spectroscopy. The electron affinity of the 7-AI radical is measured to be 2.6967(8) eV (21 751 ± 6 cm −1 ). Two excited electronic states of the neutral radical are observed at 0.8 eV and 1.4 eV above the ground state. Two minor isomers of 7-AI − due to deprotonation from the α- and β-carbon on the pyrrole ring are also detected with lower adiabatic detachment energies. A DBS is observed for the 7-AI − anion at 156 cm −1 below the detachment threshold, along with 16 vibrational Feshbach resonances. Resonant two-photon photoelectron imaging reveals that the DBS is relatively long-lived. Resonant photoelectron spectroscopy via the vibrational Feshbach resonances of the DBS gives rise to rich vibrational features for the 7-AI radical not accessible in conventional photoelectron spectroscopy. Fundamental vibrational frequencies for 16 vibrational modes of the 7-AI neutral radical are measured experimentally, including 7 bending modes. The current work provides extensive experimental electronic and vibrational information for the 7-AI − anion and the 7-AI radical.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Pulsed RF schemes for tearing mode stabilization

The RF stabilization of tearing modes with current condensation has the potential to increase stabilization efficiency and loosen power localization requirements. Such benefits stem from the cooperative feedback between the RF deposition and resulting island temperature perturbation governed by diffusion. A self consistent treatment of the damping of an rf ray as it traverses the island shows that low damping scenarios can require unfavorably high powers to overcome initial power leakage and effectively capitalize on the nonlinear effect. In this work it is demonstrated that for such regimes,modulated stabilization schemes can achieve significant improvements in heating and current drive contributions to stabilization for the same average power as a continuous wave scheme. The impact of modulation frequency and duty cycle on the performance is explored, the results of which suggest modulation strategies in which the pulsing periods are kept on the order of a diffusive time.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Stringent upper limit on the direct 3α decay of the Hoyle state in 12 C

We investigate an implication of the most recent observation of a second J π = 2 + state in 12 C, which was measured using the 12 C(γ,α) 8 Be (g.s.) reaction. In addition to the dissociation of 12 C to an α-particle and 8 Be in its ground state, a small fraction of events (2%) were identified as direct decays and decays to excited states in 8 Be. This allowed a limit on the direct 3α partial decay width to be determined as Γ 3α < 32(4) keV. Since this 2 + state is predicted by all theoretical models to be a collective excitation of the Hoyle state, the 3α partial width of the Hoyle state is calculable from the ratio of 3α decay penetrabilities of the Hoyle and 2 + states. Here, this was calculated by using the semiclassical Wenzel-Kramers-Brillouin approach and we deduce a stringent upper limit for the direct decay branching ratio of the Hoyle state of Γ 3α /Γ < 5.7 × 10 –6 , over an order of magnitude lower than previously reported. This result places the direct measurement of this rare decay mode beyond current experimental capabilities.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2019

Multimessenger asteroseismology of core-collapse supernovae

In this work we investigate correlated gravitational wave and neutrino signals from rotating core-collapse supernovae with simulations. Using an improved mode identification procedure based on mode function matching, we show that a linear quadrupolar mode of the core produces a dual imprint on gravitational waves and neutrinos in the early post-bounce phase of the supernova. The angular harmonics of the neutrino emission are consistent with the mode energy around the neutrinospheres, which points to a mechanism for the imprint on neutrinos. Thus, neutrinos carry information about the mode amplitude in the outer region of the core, whereas gravitational waves probe deeper in. We also find that the best-fit mode function has a frequency bounded above by ~420 Hz , and yet the mode’s frequency in our simulations is ~15 % higher, due to the use of Newtonian hydrodynamics and a widely used pseudo-Newtonian gravity approximation. This overestimation is particularly important for the analysis of gravitational wave detectability and asteroseismology, pointing to limitations of pseudo-Newtonian approaches for these purposes, possibly even resulting in excitation of incorrect modes. In addition, mode frequency matching (as opposed to mode function matching) could be resulting in mode misidentification in recent work. Lastly, we evaluate the prospects of a multimessenger detection of the mode using current technology. The detection of the imprint on neutrinos is most challenging, with a maximum detection distance of ~ 1 kpc using the IceCube Neutrino Observatory. The maximum distance for detecting the complementary gravitational wave imprint is ~ 5 kpc using Advanced LIGO at design sensitivity.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2026

Applications of Solid-State Transformers for Electric Power Grid HEMP/GMD Resilience

A high-altitude electromagnetic pulse (HEMP) or geomagnetic disturbance (GMD) can disrupt power grids by inducing low-frequency common-mode (CM) currents. When these currents flow through grounded transformers, they can bias the magnetic core, driving it into saturation and reducing performance or damaging equipment. This work presents a solid-state transformer (SST) to replace vulnerable assets and improve grid resilience. The paper reviews half-cycle saturation in conventional transformers, then describes an SST architecture that neutralizes and redirects CM currents during HEMP/GMD events. A prototype SST is built and validated, demonstrating stable CM-disturbance operation and protection of nearby transformers. Finally, large-scale simulations show how coordinated SST deployment mitigates CM disturbances and strengthens overall grid resilience.

four-leg inverter↗
DOE OSTI2020

Improving Gas Reactor Design with Complex Non-Standard Reaction Mechanisms in a Reactive Flow Model

Fluorinated gases are critical to a number of high-technology industries including semiconductor manufacturing and related processes such as flat panel display, LED, and photovoltaic manufacturing. These fluorinated gases have very high global warming potentials (GWPs) and, unfortunately are chemically very stable, in some cases lasting for thousands of years in the atmosphere. For environmental reasons, it is imperative that the release of these gases be minimized, but existing methods to destroy them requires a significant amount of energy. The goal of this project was to develop a more energy efficient method of destroying these high GWP gases using computational fluid dynamics, but the computational requirements are significant. In this project, we bring together resources available at the national labs, including high-performance computing hardware and modern computational methods, in order to explore an industrially important problem with key environmental and economic impact. In this project, we examined the state-of-the-art models for the physical processes involved, and made subtle changes to arrive at alternative formulations considerably better suited for computation and study. We examined several representative scenarios and developed a set of analyses techniques and tools that could be used to explore the systems in much greater detail. This exploratory project has demonstrated to ALZETA that HPC can indeed provide a unique view into their complex engineering problem - one that is simply inaccessible by any other means. The tools allow us to explore the details of the chemical process, and allow one to construct "what-if" scenarios to address shortcomings of the physical device in its current operating modes. However, as with many sources of completely new information, many new questions are illuminated with this capability. It will take considerable time, effort and experience before we learn to probe the solutions, pose operating scenarios and confirm modifications to the device that lead to real engineering advances.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Test Article and Test Plan for Heat-Pipe Gap-Conductance Testing

The SPHERE Facility at INL is established to test phenomena related to heat pipes in nuclear applications. The current capability of the SPHERE testbed is operation of liquid alkali-metal-cooled heat pipes in a variety of atmospheres. The controlled atmosphere can be used to prevent oxidation of system parts and also to affect the thermal conductivity of gases for any interfacial gaps within the heat-pipe assembly. Currently available modes are vacuum, air, nitrogen, helium, and argon. Controlled mixtures of helium and argon are available to vary the thermal conductivity of the gas. The primary test article will be based on the existing 7-hole block design used for shakedown testing of the SPHERE Facility. The SPHERE test stand will be used with test articles to establish the conductivity between fuel elements as well as between the heat pipe and other layers of the fuel-rod assembly. Existing and new test blocks will be used and modified with additional instrumentation to establish the thermal conductivity between the gap of the block wall and the heat pipes.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Ensuring a Nuclear Power Plant Safe State Following an EMP Event - Task 7 Deliverable: EMP Testing of Secondary Coupling to Instrumentation Cables

Sandia National Laboratories performed tests to address the potential vulnerability concerns of a coupled High-Altitude Electromagnetic Pulse (HEMP) inducing secondary coupling onto critical instrumentation and control cables in a nuclear power plant, with specific focus on early-time HEMP. Three types of receiving cables in nine configurations were tested to determine transfer functions between two electrically separated cables referenced to the common mode input current on the transmitting cable. One type of transfer function related the input short circuit current and resulting open circuit voltage on the receiving cable. The other transfer function related the input short circuit current and the resulting short circuit current on the receiving cable. A 500 A standard HEMP waveform was input into the transfer functions to calculate peak coupling values on the receiving cables. The highest level of coupling using the standard waveform occurred when cables were in direct contact, with a peak short circuit current of 85 A and open circuit voltage of 9.8 kV, while configurations with separated cables predicted coupling levels of less than 5 A or 500 V.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2025

Update on Ce+BAF Injector Baseline Simulations

Progress in the development of the positron injector concept for the Ce+BAF is presented. The results of start-to-end positron beam tracking simulations for two injector operating modes (low current high polarized beam and high current low polarized beam) are discussed. The efficiency of the positron capture system based on a normal conducting focusing solenoid downstream of the conversion target is compared with the efficiency of a superconducting solenoid.

Ushakov [Thomas Jefferson National Accelerator Fac↗
DOE OSTI2024

Enhancement of ECCD by the current condensation effect for stabilizing large magnetic islands caused by neoclassical tearing modes in tokamak plasmas

The radio frequency current condensation effect reported in Reiman and Fisch (2018 Phys. Rev. Lett. 121 225001) is modeled in the nonlinear resistive magnetohydrodynamic code. A series of numerical investigations have been performed to investigate the enhancement of electron cyclotron current drive (ECCD) by the current condensation effect during the control of neoclassical tearing mode (NTM) in tokamak plasmas. In the numerical model, both the parallel transport and the perpendicular transport of electron temperature are considered. The EC driven current and driven perturbed electron temperature can nonlinearly evolve within the given magnetic configuration and eventually reach saturation states. The input power threshold of ECCD and the fold bifurcation phenomenon are numerically verified via nonlinear simulations. The numerical results show good agreements with the analytical results. Moreover, spatial distributions of EC current for the two solutions at different condensed level are displayed. The control effectiveness of ECCD for large NTM islands has been evaluated while considering the current condensation effect. While taking into account current condensation effect, for a sufficiently large input power, a larger island can be more effectively stabilized than a smaller one, which suggests a reassessment of the previous idea that the ECCD should always be turned on as early as possible. The potential physics mechanism behind the ECCD control have all been discussed in detail. Furthermore, the condensation effect is found to have favorable effects on the radial misalignment of ECCD. In the consideration of the situation for extremely localized control needs, a highly peaked heating profile is adopted to verify that the fold bifurcation phenomenon still exists and the current condensation effect can still take effect in this extreme condition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Predictions of m/n = 2/1 neoclassical tearing mode stabilization via high field side lower hybrid current drive on the DIII-D tokamak

Neoclassical tearing modes (NTMs) are a class of resistive instabilities that arise in tokamaks at rational surfaces and form magnetic islands. These islands flatten the pressure gradient, reducing plasma performance and may lead to disruptions if they grow large enough. Driving current within the island can stabilize the NTM, which has been achieved with electron cyclotron current drive (ECCD) on multiple devices. An alternative to ECCD is lower hybrid current drive (LHCD), which offers the advantages of increased current drive efficiency and reduced system cost. LHCD has been viewed as poorly suited for NTM suppression due to the large spatial extent of the driven current when in the multi-pass absorption regime (as has been the case in all past LHCD experiments). However, the driven current is more localized when in the single pass absorption regime, as is predicted for the DIII-D high field side (HFS) LHCD experiment. This work evaluates the feasibility of NTM suppression with HFS LHCD on DIII-D by predicting the island growth rate for a set of representative DIII-D plasmas via the modified Rutherford equation with and without the application of LHCD. In these plasmas, NTM suppression is achieved at reasonable power levels, even with finite misalignment between LH current and the island. The effect of current condensation was included and found to be most significant at smaller island sizes, assuming an experimentally typical temperature perturbation amplitude of 10%.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗