Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Cu”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Catalytic Site Requirements for N2O Decomposition on Cu-, Co-, and Fe-SSZ-13 Zeolites

N2O decomposition is investigated on Cu, Co and Fe-exchanged SSZ-13 zeolite catalysts at relatively low metal loadings. The catalysts are synthesized by solution ion exchange, and subjected to X-ray diffraction (XRD), temperature-programed-reduction by H2 (H2-TPR), temperature-programed-reaction of N2O (N2O-TPR) coupled with in-situ transmission FTIR, and finally steady-state flow reaction tests. At low N2O pressures (< 0.05 kPa), all catalysts display pseudo first-order kinetics. From Arrhenius analysis, Cu and Fe-SSZ-13 display very different apparent activation energies but similar pre-exponential factors, suggesting their similar reaction mechanisms. N2O decomposition follows a dual-site mechanism, occurring on dimeric M-O-M sites in these catalysts, and O2 is formed by the combination of two O ad-atoms from two vicinal metal sites. Under low N2O pressure (0.05 kPa) and first-order kinetic regime, the reaction is limited by N-O cleavage on bare metal active sites. In comparison to Cu-SSZ-13, the much higher N2O decomposition rate over Fe-SSZ-13 is attributed to the much lower activation barriers for the N-O cleavage step. N2O decomposition occurs on isolated Co2+ ions in Co-SSZ-13. The rate-limiting step is N-O cleavage on an O-occupied Co site in the low-pressure first order kinetic regime. This single-site mechanism leads to much higher pre-exponential factors as compared to the dual-site mechanism. This beneficial factor for reaction rate enhancement, however, is compromised by the much higher activation barriers over this catalyst.

Lin, Fan↗
DOE OSTI2021

Local Structural Disorder in Metavanadates MV 2 O 6 (M = Zn and Cu) Synthesized by the Deep Eutectic Solvent Route: Photoactive Oxides with Oxygen Vacancies

Metavanadates MV 2 O 6–δ (M = Zn and Cu) are synthesized by using a deep eutectic solvent (DES), a mixture of hydrogen bond donor and acceptor, as a reaction medium. Dissolution of stable binary metal oxides in a DES followed by a heat treatment yields phase-pure vanadates. According to in situ powder X-ray diffraction, ternary phases (α-Zn 2 V 2 O 7 and β-Cu 2–x V 2 O 7 , x ~ 0.27) are intermediates in the reaction pathway taken. Identifying a polymorphic phase transformation temperature for CuV 2 O 6 as well as the narrow temperature range between formation and decomposition for both metavanadates allows for tackling the challenge of the synthesis of these materials. The oxygen vacancy introduced by the DES route is accompanied by the formation of reduced V 4+ and Cu + in the oxide matrix, based on X-ray photoelectron spectroscopy. These oxygen vacancies modify the vibrational modes in the corresponding Raman spectra and are also responsible for broad optical absorptions in the 1.8–1.1 eV range. The optical band gaps of the materials are found at 1.8 eV (CuV 2 O 6 ) and 2.2 eV (ZnV 2 O 6 ), approximately 0.1–0.3 eV below the values reported in the literature. The reduced band gaps and sub-band gap photon absorption are key features of the oxygen-deficient metavanadates. Surface photovoltage spectroscopy reveals that all the synthesized vanadates are n-type materials with electrons as the majority charge carriers, and photoelectrochemical measurements confirm photoanodic currents for methanol oxidation. Furthermore, these results provide insight into the synthesis and structure–property relationship of the metavanadates for their potential use as photoanodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

A Dicopper Nitrenoid by Oxidation of a Cu'Cu' Core: Synthesis, Electronic Structure, and Reactivity

A dicopper nitrenoid complex was prepared by formal oxidative addition of the nitrenoid fragment to a dicopper(I) center by reaction with the iminoiodinane PhINTs (Ts = tosylate). This nitrenoid complex, (DPFN)Cu 2 (μ-NTs)[NTf 2 ] 2 (DPFN = 2,7-bis(fluorodi(2-pyridyl)methyl)-1,8-naphthyridine), is a powerful H atom abstractor that reacts with a range of strong C–H bonds to form a mixed-valence Cu(I)/Cu(II) μ-NHTs amido complex in the first example of a clean H atom transfer to a dicopper nitrenoid core. In line with this reactivity, DFT calculations reveal that the nitrenoid is best described as an iminyl (NR radical anion) complex. The nitrenoid was trapped by the addition of water to form a mixed-donor hydroxo/amido dicopper(II) complex, which was independently obtained by reaction of a Cu 2 (μ-OH) 2 complex with an amine through a protonolysis pathway. Furthermore, this mixed-donor complex is an analogue for the proposed intermediate in copper-catalyzed Chan–Evans–Lam coupling, which proceeds via C–X (X = N or O) bond formation. Treatment of the dicopper(II) mixed donor complex with MgPh 2 (THF) 2 resulted in generation of a mixture that includes both phenol and a previously reported dicopper(I) bridging phenyl complex, illustrating that both reduction of dicopper(II) to dicopper(I) and concomitant C–X bond formation are feasible.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Emergence of the spin polarized domains in the kagome lattice Heisenberg antiferromagnet Zn-barlowite (Zn 0.95 Cu 0.05 )Cu 3 (OD) 6 FBr

Kagome lattice Heisenberg antiferromagnets are known to be highly sensitive to perturbations caused by the structural disorder. NMR is a local probe ideally suited for investigating such disorder-induced effects, but in practice, large distributions in the conventional one-dimensional NMR data make it difficult to distinguish the intrinsic behavior expected for pristine kagome quantum spin liquids from disorder-induced effects. Here we report the development of a two-dimensional NMR data acquisition scheme applied to Zn-barlowite (Zn 0.95 Cu 0.05 )Cu 3 (OD) 6 FBr kagome lattice, and successfully correlate the distribution of the low energy spin excitations with that of the local spin susceptibility. We present evidence for the gradual growth of domains with a local spin polarization induced by 5% Cu 2+ defect spins occupying the interlayer non-magnetic Zn 2+ sites. These spin-polarized domains account for ~60% of the sample volume at 2 K, where gapless excitations induced by interlayer defects dominate the low-energy sector of spin excitations within the kagome planes.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Optoelectronic property comparison for isostructural Cu 2 BaGeSe 4 and Cu 2 BaSnS 4 solar absorbers

To target mitigation of anti-site defect formation in Cu 2 ZnSnS 4–x Se x , a new class of chalcogenides, for which Ba or Sr (group 2) replace Zn (group 12), has recently been introduced for prospective solar absorber application. Cu 2 BaGeSe 4 (CBGSe) and Cu 2 BaSnS 4 (CBTS) are two such compounds, which share a common trigonal crystal structure (P3 1 space group) and similar quasi-direct band gap (~2 eV). While CBTS-based films have already been studied, there are no reports yet on films and solar cells based on related CBGSe. To identify key differences and similarities in the electronic properties between these two materials, electronic characteristics (e.g., carrier concentration, mobility, electron affinity, defect levels, recombination, and charge carrier kinetics) of vacuum-deposited CBGSe and CBTS films are compared using a variety of characterization methods. Hall effect measurements reveal that CBGSe films have relatively higher hole carrier concentration and lower mobility (3 × 10 15 cm –3 , 0.6 cm 2 V –1 s –1 ) compared to CBTS (5 × 10 12 cm –3 , 3.5 cm 2 V –1 s –1 ). Photoelectron spectroscopy yields low electron affinity values for both CBGSe (3.7 eV) and CBTS (3.3 eV), pointing to the necessity of pursuing low electron affinity buffer materials for both types of absorbers. At low temperatures, CBGSe films show free-exciton photoluminescence, as well as pronounced deep-level emission at ~1.4 eV, while CBTS films exhibit a strong bound-exciton signal with noticeably less intense deep-level emission than for CBGSe. Charge carrier kinetics, transport, and recombination properties of both types of films are also analyzed using optical-pump terahertz-probe spectroscopy and time-resolved microwave conductivity. The first CBGSe prototype solar cells (using chemical bath deposited CdS as a buffer layer) show a maximum of 1.5% efficiency with ~0.62 V open-circuit voltage. Furthermore, the measured properties point to possible limiting factors for CBGSe and related films for PV and optoelectronics and provide insights on possible approaches for improvement within this multinary chalcogenide family.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Possible quantum phase transition in partially Cu-doped ZrNi 2-x Cu x Ga Heusler alloys

We have studied the magneto-transport properties of a series of ZrNi 2- x Cu x Ga compounds. For all Cu concentration ( x ≤ 0.5) the samples exhibited the L2 1 cubic structure at room temperature and demonstrated superconductivity below 2 K. A superconducting phase transition temperature of as low as ∼1 K and a critical magnetic field of 1.78 T was observed in the system. A linear extrapolation of T C to T = 0 highly indicated that a stoichiometry-dependent superconducting quantum phase transition may occur in ZrNi 2-x Cu x Ga at x c = 0.90.

Khan, Mahmud↗
NASA NTRS1983

Matrix effects in ion-induced emission as observed in Ne collisions with Cu-Mg and Cu-Al alloys

Ion induced Auger electron emission is used to study the surfaces of Al, Mg, Cu - 10 at. % Al, Cu - 19.6 at. % Al, and Cu - 7.4 at. % Mg. A neon (Ne) ion beam whose energy is varied from 0.5 to 3 keV is directed at the surface. Excitation of the lighter Ne occurs by the promotion mechanism of Barat and Lichten in asymmetric collisions with Al or Mg atoms. Two principal Auger peaks are observed in the Ne spectrum: one at 22 eV and one at 25 eV. Strong matrix effects are observed in the alloys as a function of energy in which the population of the second peak is greatly enhanced relative to the first over the pure materials. For the pure material over this energy range this ratio is 1.0. For the alloys it can rise to the electronic structure of alloys and to other surface tools such as secondary ion mass spectroscopy.

Ferrante, J.↗
DOE OSTI2022

Phase Transitions of Cu and Fe at Multiscales in an Additively Manufactured Cu–Fe Alloy under High-Pressure

A state of the art, custom-built direct-metal deposition (DMD)-based additive manufacturing (AM) system at the University of Michigan was used to manufacture 50Cu–50Fe alloy with tailored properties for use in high strain/deformation environments. Subsequently, we performed preliminary high-pressure compression experiments to investigate the structural stability and deformation of this material. Our work shows that the alpha (BCC) phase of Fe is stable up to ~16 GPa before reversibly transforming to HCP, which is at least a few GPa higher than pure bulk Fe material. Furthermore, we observed evidence of a transition of Cu nano-precipitates in Fe from the well-known FCC structure to a metastable BCC phase, which has only been predicted via density functional calculations. Finally, the metastable FCC Fe nano-precipitates within the Cu grains show a modulated nano-twinned structure induced by high-pressure deformation. The results from this work demonstrate the opportunity in AM application for tailored functional materials and extreme stress/deformation applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Computational Investigation of the Catalytic Hydrodeoxygenation of Propanoic Acid over a Cu(111) Surface

Cu-based alloy catalysts have recently been investigated experimentally for the hydrodeoxygenation (HDO) of biomass-derived organic acids. Here, the HDO of propanoic acid (PAc) has been studied over Cu(111) by mean-field microkinetic modeling based on parameters obtained from first-principles calculations. Models were developed for the gas- and liquid-phase HDO in condensed water and 1,4-dioxane. In agreement with experimental observations, the gas-phase PAc conversion rate is low at 573 K and increases in liquid water by 1 order of magnitude. In all reaction environments, the decarboxylation mechanism is dominant at low hydrogen partial pressures less than 0.1 bar, and the C–COO bond dissociation is the rate-controlling elementary step. This observation contrasts with the rate-controlling step identified over most group VIII metal surfaces, which is the C–OH bond dissociation in the decarbonylation mechanism. At high hydrogen (H 2 ) partial pressures greater than 10 bar, the HDO of PAc produces propionaldehyde that can readsorb and further react through decarbonylation to produce C 2 alkane products, which is conceptually different from the low H 2 partial pressure scenario. At high H 2 partial pressures, the initial hydrogenation at the carbonyl carbon of PAc becomes the rate-controlling elementary step.

Catalysts↗
DOE OSTI2021

Mechanisms of the Cu(I)-Catalyzed Intermolecular Photocycloaddition Reaction Revealed by Optical and X-ray Transient Absorption Spectroscopies

The [2 + 2] photocycloaddition provides a simple, single-step route to cyclobutane moieties that would otherwise be disfavored or impossible due to ring strain and/or steric interactions. We have used a combination of optical and X-ray transient absorption spectroscopies to elucidate the mechanism of the Cu(I)-catalyzed intermolecular photocycloaddition reaction using norbornene and cyclohexene as model substrates. We find that for norbornene the reaction proceeds through an initial metal-to-ligand charge transfer (MLCT) state that persists for 18 ns before the metal returns to the monovalent oxidation state. The Cu K-edge spectrum continues to evolve until ~5 μs and then remains unchanged for the 50 μs duration of the measurement, reflecting product formation and ligand dissociation. We hypothesize that the MLCT transition and reverse electron transfer serve to sensitize the triplet excited state of one of the norbornene ligands, which then dimerizes with the other to give the product. For the case of cyclohexene, however, we do not observe a charge transfer state following photoexcitation and instead find evidence for an increase in the metal–ligand bond strength that persists for several ns before product formation occurs. This is consistent with a mechanism in which ligand photoisomerization is the initial step, which was first proposed by Salomon and Kochi in 1974 to explain the stereoselectivity of the reaction. Furthermore, our investigation reveals how this photocatalytic reaction may be directed along strikingly disparate trajectories by only very minor changes to the structure of the substrate.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗