Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Crack propagation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Study of Near-Threshold Fatigue Crack Propagation in Pipeline Steels in High Pressure Environments

Near threshold fatigue crack propagation in pipeline steels in high pressure environments was studied. The objective was to determine the level of threshold stress intensity for fatigue crack growth rate behavior in a high strength low alloy X60 pipeline-type steel. Complete results have been generated for gaseous hydrogen at ambient pressure, laboratory air at ambient pressure and approximately 60% relative humidity as well as vacuum of 0.000067 Pa ( 0.0000005 torr) at R-ratios = K(min)/K(max) of 0.1, 0.5, and 0.8. Fatigue crack growth rate behavior in gaseous hydrogen, methane, and methane plus 10 percent hydrogen at 6.89 MPa (100 psi) was determined.

Mitchell, M.↗
DOE OSTI2020

Configurational stability of a crack propagating in a material with mode-dependent fracture energy – Part II: Drift of fracture facets in mixed-mode I+II+III

In earlier papers (Leblond et al., 2011; 2019), we presented linear stability analyses of the coplanar propagation of a crack loaded in mixed-mode I+III, based on a “double” propagation criterion combining (Griffith, 1920)’s energetic condition and (Goldstein and Salganik, 1974)’s principle of local symmetry. The difference between the two papers was that in the more recent one, the local value of the critical energy-release-rate was no longer considered as a constant, but heuristically allowed to depend upon the ratio of the local mode III to mode I stress intensity factors. This led to a much improved, qualitatively acceptable agreement of theory and experiments, for the “threshold” value of the ratio of the unperturbed mode III to mode I stress intensity factors, above which coplanar propagation becomes unstable. In this paper, the analysis is extended to the case where a small additional mode II loading component is present in the initially planar configuration of the crack, generating a small, general kink of this crack from the moment it is applied. The main new effect resulting from presence of such a loading component is that the instability modes present above the threshold must drift along the crack front during its propagation. This prediction may be useful for future theoretical interpretations of a number of experiments where such a drifting motion was indeed observed.

36 MATERIALS SCIENCE↗
NASA NTRS1960

Fatigue-Crack Propagation in Aluminum-Alloy Tension Panels

Results are presented of a series of fatigue tests to study crack propagation and the resulting stress distributions in tension panels. The panels were all of the same general design, and configurations varied mainly in the relative amount of cross-sectional area in the skin, stiffeners, and flanges. The panels were constructed of 2024-T3 and 7075-T6 aluminum alloys. It was found that the average rate of crack growth was slower in panels made of 2024-T3 aluminum alloy than in panels made of 7075-T6 aluminum alloy. All cracks initiated in the skin, and the slowest crack growth was measured in configurations where the highest percentage of cross-sectional area was in the stiffeners. Strain-gage surveys were made to determine the redistribution of stress as the crack grew across the panels. As a crack approached a given point in the skin, the stress at that point increased rapidly. The stress in the stiffeners also increased as the crack approached the stiffeners. During the propagation of the crack the stress was not distributed uniformly in the remaining area.

Whaley, Richard E.↗
NASA NTRS1991

Environmental fatigue of an Al-Li-Cu alloy. Part 1: Intrinsic crack propagation kinetics in hydrogenous environments

Deleterious environmental effects on steady-state, intrinsic fatigue crack propagation (FCP) rates (da/dN) in peak aged Al-Li-Cu alloy 2090 are established by electrical potential monitoring of short cracks with programmed constant delta K and K(sub max) loading. The da/dN are equally unaffected by vacuum, purified helium, and oxygen but are accelerated in order of decreasing effectiveness by aqueous 1 percent NaCl with anodic polarization, pure water vapor, moist air, and NaCl with cathodic polarization. While da/dN depends on delta K(sup 4.0) for the inert gases, water vapor and chloride induced multiple power-laws, and a transition growth rate 'plateau'. Environmental effects are strongest at low delta K. Crack tip damage is ascribed to hydrogen embrittlement because of the following: (1) accelerated da/dN due to part-per-million levels of H2O without condensation; (2) impeded molecular flow model predictions of the measured water vapor pressure dependence of da/dN as affected by mean crack opening; (3) the lack of an effect of film-forming O2; (4) the likelihood for crack tip hydrogen production in NaCl, and (5) the environmental and delta K-process zone volume dependencies of the microscopic cracking modes. For NaCl, growth rates decrease with decreasing loading frequency, with the addition of passivating Li2CO3, and upon cathodic polarization. These variables increase crack surface film stability to reduce hydrogen entry efficiency. The hydrogen environmental FCP resistance of 2090 is similar to other 2000 series alloys and is better than 7075.

Piascik, Robert S.↗
NASA NTRS1991

Environmental fatigue of an Al-Li-Cu alloy. I - Intrinsic crack propagation kinetics in hydrogenous environments

Deleterious environmental effects on steady-state, intrinsic fatigue crack propagation (FCP) rates (da/dN) in peak aged Al-Li-Cu alloy 2090 are established by electrical potential monitoring of short cracks with programmed constant delta K and K(sub max) loading. The da/dN are equally unaffected by vacuum, purified helium, and oxygen but are accelerated in order of decreasing effectiveness of aqueous 1 percent NaCl with anodic polarization, pure water vapor, moist air, and NaCl with cathodic polarization. While da/dN depends on delta K(sup 4.0) for the inert gases, water vapor and chloride induced multiple power-laws, and a transition growth rate 'plateau'. Environmental effects are strongest at low delta K. Crack tip damage is ascribed to hydrogen embrittlement because of the following: (1) accelerated da/dN due to part-per-million levels of H2O without condensation; (2) impeded molecular flow model predictions of the measured water vapor pressure dependence of da/dN as affected by mean crack opening; (3) the lack of an effect of film-forming O2; (4) the likelihood for crack tip hydrogen production in NaCl; and (5) the environmental and delta K-process zone volume dependencies of the microscopic cracking modes. For NaCl, growth rates decrease with decreasing loading frequency, with the addition of passivating Li2CO3, and upon cathodic polarization. These variables increase crack surface film stability to reduce hydrogen entry efficiency. The hydrogen environmental FCP resistance of 2090 is similar to other 2000 series alloys and is better than 7075.

Piascik, Robert S.↗
NASA NTRS1990

Corrosion fatigue crack propagation in metals

This review assesses fracture mechanics data and mechanistic models for corrosion fatigue crack propagation in structural alloys exposed to ambient temperature gases and electrolytes. Extensive stress intensity-crack growth rate data exist for ferrous, aluminum and nickel based alloys in a variety of environments. Interactive variables (viz., stress intensity range, mean stress, alloy composition and microstructure, loading frequency, temperature, gas pressure and electrode potential) strongly affect crack growth kinetics and complicate fatigue control. Mechanistic models to predict crack growth rates were formulated by coupling crack tip mechanics with occluded crack chemistry, and from both the hydrogen embrittlement and anodic dissolution/film rupture perspectives. Research is required to better define: (1) environmental effects near threshold and on crack closure; (2) damage tolerant life prediction codes and the validity of similitude; (3) the behavior of microcrack; (4) probes and improved models of crack tip damage; and (5) the cracking performance of advanced alloys and composites.

Gangloff, Richard P.↗
DOE OSTI2022

Fracture toughness and crack propagation in LX-17 and PBX 9502 insensitive high explosives

High explosive materials, and in particular insensitive high explosive (IHE) materials, are of significant interest. TATB-based LX-17 and PBX 9502 are two IHE’s and mechanical properties are an important metric of performance. In this work we present, for the first time, a study of fracture as a function of temperature and displacement rate and starter crack length on billet pressed IHE materials using a standard three point bend technique. We demonstrated that the technique can yield consistent results over time by measuring samples from the same lots 4 years later and observed that the fracture toughness of LX-17 and PBX 9502 are similar. We also determined the temperature dependence for different starter crack lengths and found that the fracture toughness generally decreases with larger starter crack sizes and temperatures. For the LX-17, where a wide temperature range of -60 C to 50 C was investigated, the impact of temperature on fracture toughness between -20 C and 23 C was less than expected. For the PBX 9502 we observed the difference in fracture toughness values between -20 C and 23 C did depend on the particular lot, and also there was a tendency of the fracture toughness to scale with the tensile strength. We also investigated the effect of a lower displacement rate and observed that while the impact on the fracture toughness was relatively small, the samples surprisingly did not break (fail) after exceeding the peak load. We took advantage of this to perform x-ray computed tomography (CT) of the samples to image crack propagation in the intact samples. We observed that cracks were generally straight and unaffected by the microstructure in the LX-17, in contrast to the PBX 9502 where the direction of the cracks would frequently change and were likely influenced by the underlying microstructure.

36 MATERIALS SCIENCE↗
NASA NTRS1985

Fatigue crack propagation of nickel-base superalloys at 650 deg C

The 650 C fatigue crack propagation behavior of two nickel-base superalloys, Rene 95 and Waspaloy, is studied with particular emphasis placed on understanding the roles of creep, environment, and two key grain boundary alloying additions, boron and zirconium. Comparison of air and vacuum data shows the air environment to be detrimental over a wide range of frequencies for both alloys. More in-depth analysis on Rene 95 shows at lower frequencies, such as 0.02 Hz, failure in air occurs by intergranular, environmentally-assisted creep crack growth, while at higher frequencies, up to 5.0 Hz, environmental interactions are still evident but creep effects are minimized. The effect of B and Zr in Waspaloy is found to be important where environmental and/or creep interactions are presented. In those instances, removal of B and Zr dramatically increases crack growth and it is therefore plausible that effective dilution of these elements may explain a previously observed trend in which crack growth rates increase with decreasing grain size.

Gayda, J.↗
NASA NTRS1988

Fatigue crack propagation of nickel-base superalloys at 650 deg C

The 650 C fatigue crack propagation behavior of two nickel-base superalloys, Rene 95 and Waspaloy, is studied with particular emphasis placed on understanding the roles of creep, environment, and two key grain boundary alloying additions, boron and zirconium. Comparison of air and vacuum data shows the air environment to be detrimental over a wide range of frequencies for both alloys. More in-depth analysis on Rene 95 shows at lower frequencies, such as 0.02 Hz, failure in air occurs by intergranular, environmentally-assisted creep crack growth, while at higher frequencies, up to 5.0 Hz, environmental interaction are still evident but creep effects are minimized. The effect of B and Zr in Waspaloy is found to be important where environmental and/or creep interactions are presented. In those instances, removal of B and Zr dramatically increases crack growth and it is therefore plausible that effective dilution of these elements may explain a previously observed trend in which crack growth rates increase with decreasing grain size.

Gayda, J.↗
NASA NTRS1986

Plastic deformation - Its role in fatigue crack propagation

Recognizing the fact that the effective driving force Delta-K(eff) determines the fatigue crack propagation (FCP) rate and that the shear strain, which is considered to develop due to an occurrence of crack closure, primarily contributes to the plastic deformation, an effort is made here to elucidate the role of plastic deformation in FCP by developing a correlation between the Delta-K(eff) and the applied driving force (Delta-K) with shear strain as variable. The disparity between Delta(K)eff) and Delta-K, which apparently increases with shear strain level, persists at lower values of Delta-K. This suggests a strong influence of the degree of localized deformation on the FCP rates in the near threshold level. Hence, an improvement of FCP rates in the near threshold level should follow an effort that promotes the plastic deformation near the crack tip to a greater degree. This approach could explain the effect of the grain size, microstructure, environment, R-ratio and crack size on the near-threshold FCP rates.

Mazumdar, P. K.↗
NASA NTRS1986

Fatigue crack propagation rate model based on a dislocation mechanism

It has been noted that the crack propagation exponent p for most metals usually varies between values of 2 and 4, and that the motion of dislocations plays an important part in determining the exponent p. Attention is presently given to the significance of the exponent p in terms of the motion of dislocations, in view of the theory of thermally activated plastic flow and the cumulative plastic strain concept for a failure criterion.

Mazumdar, P. K.↗
NASA NTRS2014

Mode I Cohesive Law Characterization of Through-Crack Propagation in a Multidirectional Laminate

A method is proposed and assessed for the experimental characterization of through-the-thickness crack propagation in multidirectional composite laminates with a cohesive law. The fracture toughness and crack opening displacement are measured and used to determine a cohesive law. Two methods of computing fracture toughness are assessed and compared. While previously proposed cohesive characterizations based on the R-curve exhibit size effects, the proposed approach results in a cohesive law that is a material property. The compact tension specimen configuration is used to propagate damage while load and full-field displacements are recorded. These measurements are used to compute the fracture toughness and crack opening displacement from which the cohesive law is characterized. The experimental results show that a steady-state fracture toughness is not reached. However, the proposed method extrapolates to steady-state and is demonstrated capable of predicting the structural behavior of geometrically-scaled specimens.

Bergan, Andrew C.↗
NASA NTRS1988

Analysis of crack propagation in roller bearings using the boundary integral equation method - A mixed-mode loading problem

Crack propagation in a rotating inner raceway of a high-speed roller bearing is analyzed using the boundary integral method. The model consists of an edge plate under plane strain condition upon which varying Hertzian stress fields are superimposed. A multidomain boundary integral equation using quadratic elements was written to determine the stress intensity factors KI and KII at the crack tip for various roller positions. The multidomain formulation allows the two faces of the crack to be modeled in two different subregions, making it possible to analyze crack closure when the roller is positioned on or close to the crack line. KI and KII stress intensity factors along any direction were computed. These calculations permit determination of crack growth direction along which the average KI times the alternating KI is maximum.

Ghosn, L. J.↗
NASA NTRS1986

A study of spectrum fatigue crack propagation in two aluminum alloys. I - Spectrum simplification. II - Influence of microstructures

An investigation of the fatigue crack propagation FCP behavior of two aluminum alloys is performed to simulate spectrum loading conditions found at critical locations in high performance fighter aircraft. Negative loads are shown to be eliminated for the tension-compression spectrum for low to intermediate maximum stress intensities, and load interactions are found to be more significant at higher stress intensities and with more plasticity at the crack tip. In the second part, the influence of microstructural features including grain size, inclusions, and dispersoids on constant amplitude and spectrum crack growth behavior in aluminum alloys is studied. At low stress intensities the I/M alloy demonstrated better FCP resistance than the P/M 7091 alloy for both constant amplitude and spectrum testing, and the inhomogeneous planar slip and large grain size of 7050 limit dislocation interactions, thereby improving FCP performance.

Telesman, J.↗