Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Chrome”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Modification of Bushing Test Rig and Research of Variable Inlet Guide Vane Bushings For Further Development of PM304 Bushings

PS304 is a high temperature solid lubricant coating comprised of a nickel-chrome binder, chrome oxide hardener, barium-calcium fluoride high temperature lubricant, and silver as the low temperature lubricant. This coating is used to lubricate Oil-Free Foil Air Bearings as they experience friction and wear during start up and shut down. The coating deposition process begins with undercutting the shaft. This area is then sandblasted to provide a rough surface for the coating to adhere to. The coating powder is then sent through the plasma spray gun and a reasonably thick layer is applied to the undercut area of the shaft. The coating is then ground down even with the surface of the shaft and gets a nice polished finish. The foil air bearings use the solid lubricant, as mentioned above, during start up and shut down. During normal operating conditions, generally above 2000RPM, the bearings utilize air as their lubricant. Foil air bearings are comprised of a thin top foil and a corrugated bump foil. They have an interference fit with the shaft before operation. As the air gets "trapped" between the top foil and the shaft, it presses the top foil against the bump foil, in turn compressing the bumps. As the bumps compress, it allows for the air to separate the top foil from the shaft, therefore, utilizing the trapped air as its lubricant.

Yanke, Anne↗

ET Toxic Metals Replacement Review SEA Spring Face to Face

The information contained in the presentation covers development work carried out under SDS projects. The intent of the effort is to find chrome(VI) free alternates to our current chromated processing solutions. The information presented reports progress in work aimed to replace our alkaline cleaner (Turco 4215), conversion coat (Iridite 14-2) and chrome (VI) compounds used in LOx tank hydrostatic proof test solution. To date we have found candidates for use in the proof test solution and alkaline cleaner. These candidates are in the final stages of testing. Lab data is reported in the presentation.

Pratz, Earl↗

Additive Manufacturing and Hot-Fire Testing of Bimetallic GRCop-84 and C-18150 Channel-Cooled Combustion Chambers Using Powder Bed Fusion and Inconel 625 Hybrid Directed Energy Deposition

Additive manufacturing (AM) is an advanced fabrication technique that is demonstrating tremendous potential to reduce fabrication lead times and costs for liquid rocket engine components. The additive manufacturing technology lends itself to fabricate components with complex features such as internal coolant channels in combustion chambers that would otherwise require complex manufacturing operations. A requirement for high performance engines is to use high conductivity, high strength materials such as copper-alloys for combustion chamber liners to provide adequate wall temperatures and meet subsequent structural margins. A further requirement of this configuration is to minimize weight by defining and fabricating material in discrete locations as required. NASA and Industry partner, Virgin Orbit, have been working to advance these technologies through development of bimetallic additive manufacturing techniques under a public-private partnership through NASA’s Announcement of Collaborative Opportunity (ACO). This partnership is advancing a bimetallic hybrid additively manufactured combustion chamber that integrates Powder Bed Fusion (PBF), specifically Selective Laser Melting (SLM), and Directed Energy Deposition (DED) blown powder techniques to optimize the chamber materials and subsequent assembly. The SLM process is being developed for the combustion chamber liner to use copper-alloys GRCop-84 (Copper-Chrome-Niobium) or C-18150 (Copper-Chrome-Zirconium). The hybrid DED blown powder technology is used to apply an integrated structural jacket and manifolds using an Inconel 625 superalloy on the outer surface of the SLM copper liner. The hybrid DED technology being used on this program is a DMG Mori Seiki AM machining center which integrates the DED blown powder with an integral subtractive (traditional) machining to minimize overall setups. A series of chambers were fabricated using these techniques with GRCop-84/Inconel 625 and C-18150/Inconel and hot-fire tested at NASA Marshall Space Flight Center (MSFC) in LOX/Kerosene (RP-1). This paper describes the process development to integrate these AM technologies into an integrated bimetallic assembly, the design of the chamber, results from hot-fire testing, and further development.

Gradl, Paul R.↗

Additive Manufacturing and Hot-fire Testing of Bimetallic GRCop-84 and C-18150 Channel-Cooled Combustion Chambers using Powder Bed Fusion and Inconel 625 Hybrid Directed Energy Deposition

Additive manufacturing (AM) is an advanced fabrication technique that is demonstrating tremendous potential to reduce fabrication lead times and costs for liquid rocket engine components. The additive manufacturing technology lends itself to fabricate components with complex features such as internal coolant channels in combustion chambers that would otherwise require complex manufacturing operations. A requirement for high performance engines is to use high conductivity, high strength materials such as copper-alloys for combustion chamber liners to provide adequate wall temperatures and meet subsequent structural margins. A further requirement of this configuration is to minimize weight by defining and fabricating material in discrete locations as required. NASA and Industry partner, Virgin Orbit, have been working to advance these technologies through development of bimetallic additive manufacturing techniques under a public-private partnership through NASA’s Announcement of Collaborative Opportunity (ACO). This partnership is advancing a bimetallic hybrid additively manufactured combustion chamber that integrates Powder Bed Fusion (PBF), specifically Selective Laser Melting (SLM), and Directed Energy Deposition (DED) blown powder techniques to optimize the chamber materials and subsequent assembly. The SLM process is being developed for the combustion chamber liner to use copper-alloys GRCop-84 (Copper-Chrome-Niobium) or C-18150 (Copper-Chrome-Zirconium). The hybrid DED blown powder technology is used to apply an integrated structural jacket and manifolds using an Inconel 625 superalloy on the outer surface of the SLM copper liner. The hybrid DED technology being used on this program is a DMG Mori Seiki AM machining center which integrates the DED blown powder with an integral subtractive (traditional) machining to minimize overall setups. A series of chambers were fabricated using these techniques with GRCop-84/Inconel 625 and C-18150/Inconel and hot-fire tested at NASA Marshall Space Flight Center (MSFC) in LOX/Kerosene (RP-1). This paper describes the process development to integrate these AM technologies into an integrated bimetallic assembly, the design of the chamber, results from hot-fire testing, and further development.

Gradl, Paul↗

On the State of the Art of Metal Interconnects for SOFC Application

One of the recent developments for Solid Oxide Fuel Cells (SOFC) is oxide component materials capable of operating at lower temperatures such as 700-800C. This lower temperature range has provided for the consideration of metallic interconnects which have several advantages over ceramic interconnects: low cost, ease in manufacturing, and high conductivity. Most metals and alloys will oxidize under both the anode and cathode conditions within an SOFC, thus a chief requirement is that the base metal oxide scale must be electrically conductive since this constitutes the majority of the electrical resistance in a metallic interconnect. Common high temperature alloys form scales that contain chrome, silicon and aluminum oxides among others. Under SOFC operating conditions chrome oxide is a semi-conductor while silicon and aluminum oxides are insulators. In this talk we will review the evolution in candidate alloys and surface modifications which constitute an engineered solution for SOFC interconnect applications.

30 DIRECT ENERGY CONVERSION↗

ANS Winter 2022: ATF-2C Physics Safety and Scoping Analysis

ATF-2C comprises four tiers with six rodlets each. The experiment test train (TT) is situated in Loop 2A in the center flux trap (CFT) of the ATR, in which typical pressurized water reactor (PWR) conditions shall be approximated. Tier 1 (bottom) of the TT tests Framatome silicon carbide (SiC) cladding, containing molybdenum heater rods. Low-enriched uranium (LEU) Framatome rodlets with chrome-coated M5 cladding have been modeled in their place for the physics safety analysis to allow the substitution of this tier with fuel if needed. Tier 2 tests LEU Framatome rodlets with M5 cladding, which had irradiated in ATR in prior ATF experiments. Tier 3 tests General Atomics SiC composite cladding, also containing molybdenum heater rods. Tier 4/5/6 (top) tests the Japan Atomic Energy Agency (JAEA)/Mitsubishi Heavy Industries (MHI) fueled rodlets. This upper tier tests LEU rodlets with chrome-coated MDA cladding—several with temperature or pressure instrumentation. To flatten the axial power profile, lower portion of Tier 4/5/6 is surrounded by a hafnium (Hf) shroud, and the bottom two UO2 pellets are of natural enrichment. The ATF-2C TT is to be irradiated in the CFT of ATR (Fig. 1) for three or four 60-day cycles.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Chloride-Induced Stress Corrosion Cracking Characteristics of the Used Nuclear Fuel Canister Material

The used nuclear fuel (UNF) dry storage systems are located in the coastal and lake/river-side regions, the service time of which is 60 years and more. One type of dry storage systems is composite of a thin-walled austenitic stainless steel (SS) welded canister and a concrete overpack. The air flows through the canister surface and brings away the decay heat. Meanwhile, the air brings the salt species into the canister and make them deposit on the surface. The salt deposit will be deliquescent when absorbing the moisture air, being corrosive to the surface. NRC and other programs claimed that chloride induced stress corrosion cracking (CISCC) would lead to the canister failure, being one of the major technical gaps for extended dry storage systems. CISCC is induced by the combined influence of the aggressive environment (chloride ions in our case) and tensile stresses (residual stresses in our case) on the susceptible materials (the austenitic SS in our case). Chrome (Cr), as one of the chemical compositions of SSs, plays an important role in the corrosion resistance. It can form a chrome-rich inner barrier oxide layer to prevent the SS from corrosion. However, chloride ions can easily break down the barrier and accelerate dissolution of the underlying metal, the phenomena of which is pitting corrosion. Pitting is the precursor to CISCC as which provides the combination of a local aggressive solution chemistry and a stress concentrating feature. Accordingly, CISCC invariably originates from the pits, and cracks that have nucleated on pit walls can grow around the pit and coalesce to form a complete through-crack. Significant tensile residual stresses, caused by the welding process, exist throughout the thickness of the canister wall. Enos and Bryan found that large residual stresses were in the full-scale mockup container simulating a canister, which supports the SCC propagation. It is therefore interesting to achieve a good knowledge about the effect of welding on the durability of SSs, especially in the corrosive environment. In order to understand the fundamental of the cracking behaviors, it's vital to elucidate the microstructure and microchemistry of cracking. This study focused on observing the CISCC characteristics of the UNF canister material exposed to the humid environment with salt deposit. Extensive micro-characteristics have been achieved by the techniques include focused ion beam/ scanning electron microscope (FIB/SEM), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), and optical profiler. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The visible laser absorption property of chromium-doped polyvinyl alcohol films: synthesis, optical and dielectric properties

New films for visible laser filter were fabricated from poly(vinyl alcohol), PVA, and various levels of chrome(III) chloride, CrCl{sub 3}, by a known simple process named casting. The structure order degree, complex interaction, as well as optical filtering characteristic of the PVA + xCrCl{sub 3} (x = 0.037, 0.37, 3.7, 18.5 and 37 wt%) samples were investigated via the diffraction of the X-ray, Fourier transform infrared spectroscopy and UV/Vis/NIR spectrum, respectively, while the behavior of optical limiting was tested by set-up laser limiting measurement. The increment of Cr{sup 3+}-doping level in the PVA gives some results as, (I) a marked increase in the degree of random structure of the samples, and (II) two clearly absorption peaks are seen around 428 nm and 608 nm with a progressive increase in the intensity and a slight shift to a higher wavelength. (III) Three distinguished energy gaps were clearly observed, as well as, (IV) the dielectric spectroscopy of the samples was decreased with increasing the Cr{sup 3+}-doping, which contributes to the strong interaction among the mixtures. Furthermore, at concentrations above 0.37 wt% of Cr{sup 3+}-doping, a notable decrease in the output detected laser power was observed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

An Investigation on the Wear and Corrosion Behavior of HVOF-Sprayed WC-12Co-Al{sub 2}O{sub 3} Cermet Coating

The aim of the present study is to develop thermally sprayable WC-12Co and WC-12Co-xAl{sub 2}O{sub 3} (x = 10 and 15 wt.%) cermet coatings on steel substrate (SS 304) by high-velocity oxy fuel (HVOF) method. Influence of Al{sub 2}O{sub 3} addition on the wear and corrosion behavior of WC-12Co coating has been studied. The microstructure and chemical composition of the coatings were analyzed using field emission scanning electron microscope (FESEM), and phase identification was carried out using x-ray diffraction (XRD) studies. The morphology of the coating appears as coarse granular structure. The XRD studies revealed the presence of hexagonal WC phase along with η-Co{sub 6}W{sub 6}C phase. It has been observed from the microhardness measurements, that the values gradually increase from 950 to 1300 HK with the addition of Al{sub 2}O{sub 3} from 0 to 15 wt.%. The wear rate of WC-12Co-15Al{sub 2}O{sub 3} (3.19 × 10{sup −6} mm{sup 3}/Nm) and WC-12Co-10Al{sub 2}O{sub 3} (5.26 × 10{sup −6} mm{sup 3}/Nm) coatings was seen to be one order of magnitude lower than that of WC-12Co (2.9 × 10{sup −5} mm{sup 3}/Nm) coating. The polarization studies revealed that WC-12Co-15Al{sub 2}O{sub 3} cermet coating showed superior corrosion protection than that of WC-12Co-10Al{sub 2}O{sub 3} and WC-12Co coatings. This has been attributed to the gradual decrease in the porosity levels with an increase in Al{sub 2}O{sub 3} content which is supported by morphology studies. The microhardness and wear behavior of WC-12Co-Al{sub 2}O{sub 3} coatings are equivalent to those of hard chrome suggesting the possibility of its replacement.

36 MATERIALS SCIENCE↗

Material erosion measurements and expected operational lifetime of a deployable photon sieve payload

Spacecraft operating in low-Earth orbit are subjected to a number of hazardous environmental constituents that can lead to decreased system performance and reduced operational lifetimes. Due to their thermal, optical, and mechanical properties, polymers are used extensively in space systems; however they are particularly susceptible to material erosion and degradation as a result of exposure to the LEO environment. The focus of this research is to examine the material erosion and mass loss experienced by a custom Kaptonlike polyimide due to exposure in a simulated low-earth orbit environment. The deployable membrane telescope design discussed in this research is named Peregrine and is the scientific payload for FalconSat-7, a 3U cubesat designed and developed at the United States Air Force Academy (USAFA) for the purpose of demonstrating the capability of deployable membrane telescope technology on a nanosatellite platform. In addition to the polymer samples, chrome, silver and gold specimens will be examined to measure the oxidation rate and act as a control specimen, respectively. A magnetically filtered atomic oxygen plasma source has previously been developed and characterized for the purpose of simulating the low-Earth orbit environment. The plasma source can be operated at a variety of discharge currents and gas flow rates, of which the plasma parameters downstream of the source are dependent. The characteristics of the generated plasma were examined as a function of these operating parameters to optimize the production of O + ions with energy relevant to LEO applications. The erosion yield of the Kapton-like polyimide was experimentally determined to be 2.84 x 10 -24 cm 3 per atom which is in close agreement when compared to the on-orbit measurement for reaction efficiency of Kapton HN. We report the experimentally determined reaction rate for the Kapton-like polyimide was used to estimate the operational lifetime of the photon sieve during the solar conditions expected beginning in May 2019. The effective lifetime is estimated between 126 and 153 days.

36 MATERIALS SCIENCE↗

Heavy metals in liquid pig manure in light of bacterial antimicrobial resistance

Heavy metals are regularly found in liquid pig manure, and might interact with bacterial antimicrobial resistance. Concentrations of heavy metals were determined by atomic spectroscopic methods in 305 pig manure samples and were connected to the phenotypic resistance of Escherichia coli (n=613) against 29 antimicrobial drugs. Concentrations of heavy metals (/kg dry matter) were 0.08-5.30 mg cadmium, 1.1-32.0 mg chrome, 22.4-3387.6 mg copper, <2.0-26.7 mg lead, <0.01-0.11 mg mercury, 3.1-97.3 mg nickel and 93.0-8239.0 mg zinc. Associated with the detection of copper and zinc, resistance rates against {beta}-lactams were significantly elevated. By contrast, the presence of mercury was significantly associated with low antimicrobial resistance rates of Escherichia coli against {beta}-lactams, aminoglycosides and other antibiotics. Effects of subinhibitory concentrations of mercury on bacterial resistance against penicillins, cephalosporins, aminoglycosides and doxycycline were also demonstrated in a laboratory trial. Antimicrobial resistance in the porcine microflora might be increased by copper and zinc. By contrast, the occurrence of mercury in the environment might, due to co-toxicity, act counter-selective against antimicrobial resistant strains.

60 APPLIED LIFE SCIENCES↗

Study on impact of Cr and Mo on diffusion of H in 2.25Cr1Mo steel using first-principle calculations

Chrome-molybdenum steel (2.25Cr1Mo steel) is one of the main materials of a steam generator (SG) in high-temperature reactor-pebblebed modules (HTR-PM). It is essential to analyze the source term of tritium in this material, because the behavior of tritium in a SG is important for performing source term analysis in normal and accident conditions. In this article, the diffusion behavior of H atom in 2.25Cr1Mo steel was calculated to estimate the diffusivity of tritium using first-principles density functional theory. To develop and simplify the model of hydrogen diffusion in 2.25Cr1Mo steel, the impact of Cr and Mo on the diffusion of hydrogen in bcc-Fe were first calculated, all the possible diffusion paths were considered, and the minimum energy path was obtained. The diffusion activation energy and pre-exponential factor of the diffusion coefficient were obtained from Vienna Ab initio Simulation Package combined with the climbing image-nudged elastic band method. Here the results indicate that the minimum energy path for the impurity H atom is from one tetrahedral interstitial site to an adjacent tetrahedral interstitial site. The function of the diffusion coefficient of H in 2.25Cr1Mo steel with temperature T can be expressed as D = 1.486 X 10 -7 x ($\frac{-16.350kJ/mol}{RT}$) (M2/s). The diffusion coefficient of our calculation and some of the previous experiments have an excellent quantitative agreement, which indicates the reliability of our crystalline model and the practicability of the present theoretical approach. More importantly, the computational results in this work can be treated as a good screening method to collect reasonable experimental data, which will provide a good reference for tritium source term evaluation in the SG of the HTR-PM.

36 MATERIALS SCIENCE↗

Characterization of stress corrosion cracks in Ni-based weld alloys 52, 52M and 152 grown in high-temperature water

Ni-based weld alloys 52, 52M and 152 are extensively used in repair and mitigation of primary water stress corrosion cracking (SCC) in nuclear power plants. In the present study, a series of microstructure and microchemistry at the SCC tips of these alloys were examined with scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDS), scanning transmission electron microscopy (STEM) and energy filtered transmission electron microscopy (EFTEM). The specimens have similar chemical compositions and testing conditions. Intergranular (IG) and transgranular (TG) SCC was observed in all of them. The cracks were filled with nickel-oxides and partial precipitations of chrome carbides (CrCs), niobium carbides (NbCs), titanium nitrides (TiNs) and silicon carbides (SiCs), while iron (Fe) was largely dissolved into the solution. However, the crack densities, lengths and distributions were different for all three specimens. - Highlights: • Microstructure and microchemistry at the SCC tips of Ni-based weld alloys 52, 52M and 152 were examined. • The crack densities, lengths and distributions were found to be different for different alloys. • IGSCC and TGSCC were observed on alloy 52, only TGSCC was observed on alloy 52M and 152. • The cracks were filled by Ni-oxides and precipitated CrCs, NbCs, TiNs and SiCs.

36 MATERIALS SCIENCE↗

Characterization of oxide scales grown on alloy 310S stainless steel after long term exposure to supercritical water at 500 °C

The oxide scale grown of static capsules made of alloy 310S stainless steel was investigated by exposure to the supercritical water at 500 °C 25 MPa for various exposure times up to 20,000 h. Characterization techniques such as X-ray diffraction, scanning/transmission electron microscopy, energy dispersive spectroscopy, and fast Fourier transformation were employed on the oxide scales. The elemental and phase analyses indicated that long term exposure to the SCW resulted in the formation of scales identified as Fe{sub 3}O{sub 4} (outer layer), Fe-Cr spinel (inner layer), Cr{sub 2}O{sub 3} (transition layer) on the substrate, and Ni-enrichment (chrome depleted region) in the alloy 310S. It was found that the layer thickness and weight gain vs. exposure time followed parabolic law. The oxidation mechanism and scales grown on the alloy 310S stainless steel exposed to SCW are discussed. - Highlights: •Oxidation of alloy 310S stainless steel exposed to SCW (500 °C/25 MPa) •The layer thickness and weight gain vs. exposure time followed parabolic law. •Oxide layers including Fe{sub 3}O{sub 4} (outer), Fe-Cr spinel (inner) and Cr{sub 2}O{sub 3} (transition) •Ni element is segregated by the selective oxidation of Cr.

36 MATERIALS SCIENCE↗

A study of optothermal and AC impedance properties of Cr-doped Mn{sub 3}O{sub 4} sprayed thin films

Highlights: • Outlining adequacy an original combination of several characterization means. • Structural, optical, thermal and electrical properties have been studied. • Opto- thermal analysis shows that band gap can be tuned through Cr doping. • Outlining physical properties for an eventual development of sensing components. - Abstract: Chrome-doped Mn{sub 3}O{sub 4} thin films were grown on the glass substrates by the spray pyrolysis technique at 350 °C. XRD diffraction and Raman spectroscopy analysis revealed that all samples have tetragonal spinel structure with a preferred orientation along the direction (1 0 1). Absorption coefficient has been measured using both transmission and mirage effect. The band gap energy decreases from 2.2 to 1.9 eV with Cr content while Urbach energy value increases from 354 to 473 meV. Also, thermal conductivity was evaluated. Finally, physical properties have been evaluated and discussed in terms of alteration of the band gap edges, electrical patterns and mirage effect.

36 MATERIALS SCIENCE↗

In situ synchrotron X-ray imaging of 4140 steel laser powder bed fusion

In this study, an in situ synchrotron X-ray imaging technique was used to examine laser powder bed fusion (LPBF) of a chrome-molybedum, AISI 4140, ferrite–bainite steel, from a moving laser source. Since 4140 has received only minimal attention in the AM literature, focus here was on the effects of melt pool dynamics, vapor cavity depths, build layer height, and the origin of porosity on the 4140 as-built microstructure. Four build parameter sets, which enabled variation of laser power, scan speed, laser spot size, and specific energy density (SED), were applied. Vapor cavity and melt pool depths were measured for each single-track laser scan. Direct imaging of the LPBF process demonstrated that the primary source of porosity in the build originates from incorporation of entrapped gas within the powder irrespective of build parameter set. High resolution SEM and EBSD demonstrated that the as-built microstructure did not vary significantly with build parameter set over a broad range of SED. The fast solidification rates observed (0.06–0.08 m/s) lead to fine martensite packet/block size distributions (1–3 µm) with the potential for increased material strength.

36 MATERIALS SCIENCE↗

A preliminary investigation into the electrodeposition and synthesis of radiopure Copper–Chromium alloys for rare-event physics detector systems

Current investigations into neutrinoless double beta decay and the direct detection of dark matter require increasingly sensitive detector systems that demand ultra-low background materials. These requirements have previously been attained using ultra-radiopure electroformed (EF) copper. However, pure copper possesses high ductility and relatively low strength, which necessitates the need for large amounts of material and extra care during fabrication to help minimize galling and mechanical failure. Furthermore, we investigate an alloying alternative to pure EF copper by examining low wt% copper chrome (Cu–Cr) solid solution alloys, with inquiries into alloy hardness, strength, and radiopurity. Alloyed Cu–Cr layered samples are shown to exhibit significantly increased hardness compared to EF copper, for example showing a 50% increase in exhibited hardness using less than 1% Cr by weight, with limited negative impact to the material’s radiopurity.

Background↗

FLiNaK Compatability Studies with Inconel 600 and Silicon Carbide

A small liquid fluoride salt test apparatus has been constructed and testing conducted to examine the compatibility of SiC, Inconel 600, and a spiral wound gasket material in FLiNaK salt. These tests were conducted to test materials and sealing systems that would be used in a FLiNaK salt test loop. Three months of testing at 700oC was used to assure that these materials and seals would be acceptable operating under expected test loop conditions. The SiC specimens showed little or no change over the test period while the spiral wound gasket material showed no degradation, except for the possibility of salt seeping into the outermost spirals of the gasket. The Inconel 600 specimens showed regions of voiding which penetrated the specimen surface to about 250 m in depth. Analysis indicated that the salt had leached chrome from the Inconel surface as was expected for this material. Because the test loop will have a limited working lifetime, it was concluded that these materials would be satisfactory for loop construction.

42 ENGINEERING↗