Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COPPER 65”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6

Crystallization kinetics of Mg–Cu–Yb–Ca–Ag metallic glasses

The paper presents research into a Mg–Cu–Yb system based metallic glassy alloys. Metallic glasses were prepared using induction melting and further injection on a spinning copper wheel. The effect of alloying by Ag and Ca on the glass forming ability and the kinetics of crystallization of Mg–Cu–Yb system based alloys were studied. The differential scanning calorimeter and X-ray diffractometer were used to investigate the kinetics of crystallization and the phase composition of the samples. An indicator of glass forming ability, effective activation energy of crystallization, and enthalpy of mixing were calculated. An increase of the Ca and Ag content has a positive effect on the glass forming ability, the effective activation energy of crystallization, and the enthalpy of mixing. The highest indicators of the glass forming ability and the thermal stability were found for alloys that contain both alloying elements. The Ag addition suppresses precipitation of the Mg{sub 2}Cu phase during crystallization. A dual-phase glassy-nanocrystalline Mg structure was obtained in Mg{sub 65}Cu{sub 25}Yb{sub 10} and Mg{sub 59.5}Cu{sub 22.9}Yb{sub 11}Ag{sub 6.6} alloys after annealing. Bulk samples with a composite glassy-crystalline structure were obtained in Mg{sub 59.5}Cu{sub 22.9}Yb{sub 11}Ag{sub 6.6} and Mg{sub 64}Cu{sub 21}Yb{sub 9.5}Ag{sub 5.5} alloys. A thermodynamic database for the Mg–Cu–Yb–Ca–Ag system was created to compare the process of crystallization of alloys with polythermal sections of the Mg–Cu–Yb–Ca–Ag phase diagram. - Highlights: • New alloy compositions based on Mg–Cu–Yb system were developed and investigated. • Increasing content of Ag and Ca leads to improving GFA. • Bulk samples with a composite glassy-crystalline structure were obtained. • Thermodynamic database for Mg–Cu–Yb–Ca–Ag system was created.

36 MATERIALS SCIENCE↗

Shock initiation of low density polymer bonded explosive LX-14: A study of two morphologies

A series of six shock initiation experiments have been carried out on low density LX-14 powder in order to simulate a shock insult on the heavily damage polymer bonded explosive, LX-14. Two distinct morphologies were studied (tap density molding powder and machined swarf), both at the same density of 0.942 g/cm 3 , or 50.1% theoretical maximum density. The purpose of these experiments was to provide data to help make an assessment of the effects that damage has on the material sensitivity to a planar shock. This was achieved primarily by providing shock sensitivity data in the form of a Pop plot, and also reactants equation of state data, which aids in the determination of input conditions for both the experiments performed in this work and also future experiments of this material type. The experiments were of a cut-back format, consisting of four sample heights on each shot and diagnosed with optical velocimetry. The experiments were carried out at the Technical Area 40 Chamber 9 gas gun facility at the Los Alamos National Laboratory, where the LX-14 targets were subjected to Al 6061 and Oxygen Free High Conductivity copper impactors launched to velocities up to 2.14 km/s. Time corrected reactive growth wave profiles are presented in this paper along with the derivation of the following Hugoniot parameters for this explosive, where the molding powder and machine swarf are represented by the following linear equations, respectively, U s = 1.64 (±0.64)u p + 2.25 (±0.49) and U s = 0.87 (±.0.60)u p + 4.08 (±0.49). The results show that the steady increase in shock sensitivity with increasing void fraction reaches an inflection point beyond which the shock sensitivity begins to decease. This inflection point lies between 65% and 50% of the theoretical maximum density of the LX-14. In both cases, the damaged LX-14 was not as sensitive as expected, with a relative shock sensitivity of the molding powder being less than the pressed LX-14, and the machined swarf having a shock sensitivity that is comparable to pressed LX-14.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Study of Cu-Ni-Fe Alloys as Inert Anodes for Al Production in Low-Temperature KF-AlF{sub 3} Electrolyte

Cu-Ni-Fe-based alloys are considered as promising O{sub 2}-evolving anode materials for CO{sub 2}-free Al production. In the present study, biphased (as-cast) and monophased (postcasting homogenized) Cu{sub 65}Ni{sub 20}Fe{sub 15}, alloys, and monophased Ni{sub 65}Fe{sub 25}Cu{sub 10} alloy (in wt pct) are evaluated as O{sub 2}-evolving anodes for Al production in potassium cryolite at 700 °C. The produced Al purity is 99.6 wt pct, and the erosion rate is estimated at 0.4 cm year{sup −1} for both Cu{sub 65}Ni{sub 20}Fe{sub 15} anodes compared to 95.2 wt pct and 3.2 cm year{sup −1} for the Ni{sub 65}Fe{sub 25}Cu{sub 10} anode. The compositions, and morphologies of the surface oxide layer and the metal fluoride layer present at the oxide/alloy interface are compared for the three anodes. The deleterious impact of electrolyte infiltration on the surface oxide building is highlighted.

36 MATERIALS SCIENCE↗

High Compression‐Induced Conductivity in a Layered Cu–Br Perovskite

Abstract We show that the onset pressure for appreciable conductivity in layered copper‐halide perovskites can decrease by ca. 50 GPa upon replacement of Cl with Br. Layered Cu–Cl perovskites require pressures >50 GPa to show a conductivity of 10 −4 S cm −1 , whereas here a Cu–Br congener, (EA) 2 CuBr 4 (EA=ethylammonium), exhibits conductivity as high as 2×10 −3 S cm −1 at only 2.6 GPa, and 0.17 S cm −1 at 59 GPa. Substitution of higher‐energy Br 4p for Cl 3p orbitals lowers the charge‐transfer band gap of the perovskite by 0.9 eV. This 1.7 eV band gap decreases to 0.3 eV at 65 GPa. High‐pressure X‐ray diffraction, optical absorption, and transport measurements, and density functional theory calculations allow us to track compression‐induced structural and electronic changes. The notable enhancement of the Br perovskite's electronic response to pressure may be attributed to more diffuse Br valence orbitals relative to Cl orbitals. This work brings the compression‐induced conductivity of Cu‐halide perovskites to more technologically accessible pressures.

Jaffe, Adam↗

Life Cycle Assessment of Future Photovoltaic Electricity Production from Residential-scale Systems Operated in Europe

The photovoltaics (PV) industry is growing rapidly to meet the increasing demand of green power. As the industry grows, the manufacturing processes and the material and energy efficiencies of PV cells and panels are improving. To assess the impacts of this trend, future scenarios of single-crystalline (single-Si, also known as mono-crystalline) silicon and cadmium-telluride (CdTe) PV systems installed on European residences were established. Assessment of the improvement potential of PV electricity-generating technologies such as single-Si and CdTe could be considered in long-term energy strategy decisions. This study aims to provide scenario-based information about the environmental per-formance of single-Si and CdTe PV modules produced and operated in the far future (2030 to 2050). The deployment application assessed considers European residential roofs. We made scenario-dependent projections of key parameters for single-Si and CdTe PV panels manufactured in 2050. The parameters included cell efficiency, module efficiency, wafer thickness, cutting losses, kerf losses, silver use, glass thickness and operational lifetime. This study combines developments for these parameters with projections of the environmental performance of electricity mixes in the main manufacturing countries/regions (European Union, China and the United States of America) and with projections of the environ-mental performance of basic material production (aluminium, copper, magnesium, nickel, pig iron, zinc, clinker and flat glass) in the far future. The three scenarios used in the assessment of future PV electricity were categorized into three classes: 'business as usual' (BAU), 'realistic improvement' (REAL) and 'optimistic improvement' (OPT). It estimates the current life cycle greenhouse gas emissions of single-Si PV electricity produced on the roofs of European residences to be approximately 80 grams CO2-equi-valent per kWh (g CO2-eq per kWh). Based on the projected changes to key parameters and the background system, life cycle greenhouse gas (GHG) emissions could be reduced to 65% (scenario BAU), 31% (scenario REAL) and 18% (scenario OPT) of that value in the far future. Results for other life cycle assessment (LCA) metrics are also assessed in this study such as: non-renewable cumulative energy demand, acidification potential, human toxicity potential, photochemical ozone creation potential, particulate matter formation potential, and land use. We calculated the total energy payback time (EPBT) and the non-renewable energy payback time (NREPBT) in the far future of single-crystalline silicon-based PV panels operated in Europe by dividing the estimate of non-renewable cumulative energy demand of PV electricity for the given scenario by the non-renewable cumulative energy demand of the scenario-dependent national and regional non-renewable residual electricity mixes. The study estimates the payback time could be reduced from 2.4 years today to 1.7, 1.2 and 1.2 years (scenarios BAU, REAL and OPT, respectively) in the far future, based on the assumptions and projections in the analysis. It finally estimates the current life cycle greenhouse gas emissions of CdTe PV electricity produced on the roofs of European residences to be approximately 30 g CO2-eq per kWh. Based on the projected changes to key parameters and the background system, life cycle GHG emissions could be reduced to 70% (scenario BAU), 44% (scenario REAL) and 32% (scenario OPT) of that value in the far future.

14 SOLAR ENERGY↗

Transparent conductive and near-infrared reflective Ga-doped ZnO/Cu bilayer films grown at room temperature

Bilayer films consisting of Ga-doped ZnO (GZO) and Cu layers were grown at room temperature by magnetron sputtering. The structural, electrical, and optical properties of GZO/Cu bilayer films were investigated in detail. The crystallinity and transparent-conductive properties of the films were correlated with the Cu layer thickness. The GZO/Cu bilayer film with the Cu layer thickness of 7.8 nm exhibited a low resistivity of 7.6x10{sup -5} {Omega} cm and an average visible transmittance of 74%. The reflectance was up to 65% in the near-infrared region for this film. The transparent conductive and near-infrared reflective GZO/Cu bilayer films could be readily deposited at room temperature. The GZO/Cu bilayer films were thermally stable when annealed at temperatures as high as 500 deg. C.

36 MATERIALS SCIENCE↗

Updates to the n+ 63,65 Cu Angular Distributions [Slides]

The performance of the benchmark suite is very sensitive to changes in the angular distribution data. The quasi-differential measurements performed by Blain et al at RPI provide a valuable constraint. Furthermore, ENDF/B-VIII.0 disagrees with their measurements consistently at 300 keV (the transition between RRR and high energy). The next step is to conservatively adjust the Legendre coefficients near 300 keV, validating performance against both critical benchmarks and the RPI quasi-differential measurements.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Defect Creation by Linker Fragmentation in Metal-Organic Frameworks and Its Effects on Gas Uptake Properties

We successfully demonstrate an approach based on linker fragmentation to create defects and tune the pore volumes and surface areas of two metal-organic frameworks, NU-125 and HKUST-1, both of which feature copper paddlewheel nodes. Depending on the linker fragment composition, the defect can be either a vacant site or a functional group that the original linker does not have. In the first case, we show that both surface area and pore volume increase, while in the second case they decrease. The effect of defects on the high-pressure gas uptake is also studied over a large temperature and pressure range for different gases. We found that despite an increase in pore volume and surface area in structures with vacant sites, the absolute adsorption for methane decreases for HKUST-1 and slightly increases for NU-125. However, the working capacity (deliverable amount between 65 and 5 bar) in both cases remains similar to parent frameworks due to lower uptakes at low pressures. In the case of NU-125, the effect of defects became more pronounced at lower temperatures, reflecting the greater surface areas and pore volumes of the altered forms.

Barin, G↗

Silica-copper catalyst interfaces enable carbon-carbon coupling towards ethylene electrosynthesis

Membrane electrode assembly (MEA) electrolyzers offer a means to scale up CO 2 -to-ethylene electroconversion using renewable electricity and close the anthropogenic carbon cycle. To date, excessive CO 2 coverage at the catalyst surface with limited active sites in MEA systems interferes with the carbon-carbon coupling reaction, diminishing ethylene production. With the aid of density functional theory calculations and spectroscopic analysis, here we report an oxide modulation strategy in which we introduce silica on Cu to create active Cu-SiO x interface sites, decreasing the formation energies of OCOH* and OCCOH*—key intermediates along the pathway to ethylene formation. We then synthesize the Cu-SiO x catalysts using one-pot coprecipitation and integrate the catalyst in a MEA electrolyzer. By tuning the CO 2 concentration, the Cu-SiO x catalyst based MEA electrolyzer shows high ethylene Faradaic efficiencies of up to 65% at high ethylene current densities of up to 215 mA cm -2 ; and features sustained operation over 50 h.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Study of Superconductivity in YBa{sub 2}Cu{sub 3}O{sub 7-x}/SrTiO{sub 3} Composites

Superconducting properties of YBa{sub 2}Cu{sub 3}O{sub 7-x} (YBCO)/SrTiO{sub 3} (STO) polycrystalline composites were investigated. The composites were obtained by rapid thermal processing of the 20% YBCO–80% STO mixtures in the air in the temperature range 700–1000 °C for 2 min. Magnetization measurements showed that the superconducting critical temperature (T{sub c}) is practically not changed if optimally doped YBCO is used in YBCO/STO composites. In contrast, a strong increase of T{sub c} from 65 to 90 K was found in the case of underdoped YBCO. This increase of T{sub c} can be explained by unusually fast diffusion of oxygen from STO to YBCO grains in sintered composites. Obtained results show that the YBCO oxidation process can be significantly accelerated in underdoped YBCO/STO composites during rapid high-temperature processing.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Interaction Between Graphene-Coated SiC Single Crystal and Liquid Copper

The wettability of graphene-coated SiC single crystal (C{sub Gn}/SiC{sup sc}) by liquid Cu (99.99%) was investigated by a sessile drop method in vacuum conditions at temperature of 1100 °C. The graphene layer was produced via a chemical vapor deposition routine using 4H-SiC single crystal cut out from 6″ wafer. A dispensed drop technique combined with a non-contact heating of a couple of materials was applied. The Cu drop was squeezed from a graphite capillary and deposited on the substrate directly in a vacuum chamber. The first Cu drop did not wet the C{sub Gn}/SiC{sup sc} substrate and showed a lack of adhesion to the substrate: the falling Cu drop only touched the substrate forming a contact angle of θ{sub 0} = 121° and then immediately rolled like a ball along the substrate surface. After settling near the edge of the substrate in about 0.15 s, the Cu drop formed an asymmetric shape with the right and left contact angles of different values (θ{sub R} = 86° and θ{sub L} = 70°, respectively), while in the next 30 min, θ{sub R} and θ{sub L} achieved the same final value of ~ 52°. The second Cu drop was put down on the displacement path of the first drop, and immediately after the deposition, it also did not wet the substrate (θ = 123°). This drop kept symmetry and the primary position, but its wetting behavior was unusual: both θ{sub R} and θ{sub L} decreased in 17 min to the value of 23° and next, they increased to a final value of 65°. Visual observations revealed a presence of ~ 2.5-mm-thick interfacial phase layer reactively formed under the second drop. Scanning electron microscopy (SEM) investigations revealed the presence of carbon-enriched precipitates on the top surface of the first Cu drop. These precipitates were identified by the Raman spectroscopy as double-layer graphene. The Raman spectrum taken from the substrate far from the drop revealed the presence of graphene, while that obtained from the first drop displacement path exhibited a decreased intensity of 2D peak. The results of SEM investigations and Raman spectroscopy studies suggest that the presence of graphene layer on the SiC substrate suppresses but does not completely prevent chemical interaction between liquid Cu drop and SiC. Both chemical degradation (etching) and mechanical degradation of the graphene layer during drop rolling due to high adhesion of the Cu drop to the SiC substrate are responsible for mass transfer through the 2nd drop/substrate interface that in turn results in significant changes of structure and chemistry of the drop and the interface.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Porous mesh manifold for enhanced boiling performance

High-performance electronics are continuously demanding cooling of higher heat fluxes. Phase-change cooling, including pool boiling, is a useful approach to address this challenge; however, competition between liquid and vapor flows generally limit the heat fluxes that can be dissipated. A range of strategies to control these flows have been investigated previously, including capillary guides. Here a manifold structure formed from a metallic mesh is investigated to control the disposition of liquid and vapor phases above a pool fed boiling surface enhanced with porous structures. Copper mesh forms defined liquid flow paths, using capillary action to guide and distribute liquid evenly over the heated surface, along with open channels to facilitate vapor escape. The mesh provides a novel structure for liquid guidance that imposes low resistance to liquid flow while occluding a minimal area of heated surface underneath. The manifold performance is characterized in boiling fed by a pool of water above a laser-textured aluminum nitride heat dissipation surface with pin–fin structures having heights of 110 µm and spacing of 30 µm with a heated area of 5 mm x 5 mm. A maximum heat flux of 490 W/cm 2 is reached with the manifold in the pool fed configuration, representing an increase of more than 65% over the porous pin fin surface alone. The maximum stable superheat observed for the manifold of 36K is 14K higher than that for the porous surface without the manifold. The factors limiting performance of the manifold are analyzed. High superheat is attributed to partial flooding of the boiling surface as suggested by the reduction in superheat using external suction. Similar systems and structures for enhanced two-phase cooling are compared.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Dose optimization in pediatric cardiac x-ray imaging

Purpose: The aim of this research was to explore x-ray beam parameters with intent to optimize pediatric x-ray settings in the cardiac catheterization laboratory. This study examined the effects of peak x-ray tube voltage (kVp) and of copper (Cu) x-ray beam filtration independently on the image quality to dose balance for pediatric patient sizes. The impact of antiscatter grid removal on the image quality to dose balance was also investigated. Methods: Image sequences of polymethyl methacrylate phantoms approximating chest sizes typical of pediatric patients were captured using a modern flat-panel receptor based x-ray imaging system. Tin was used to simulate iodine-based contrast medium used in clinical procedures. Measurements of tin detail contrast and flat field image noise provided the contrast to noise ratio. Entrance surface dose (ESD) and effective dose (E) measurements were obtained to calculate the figure of merit (FOM), CNR{sup 2}/dose, which evaluated the dose efficiency of the x-ray parameters investigated. The kVp, tube current (mA), and pulse duration were set manually by overriding the system's automatic dose control mechanisms. Images were captured with 0, 0.1, 0.25, 0.4, and 0.9 mm added Cu filtration, for 50, 55, 60, 65, and 70 kVp with the antiscatter grid in place, and then with it removed. Results: For a given phantom thickness, as the Cu filter thickness was increased, lower kVp was favored. Examining kVp alone, lower values were generally favored, more so for thinner phantoms. Considering ESD, the 8.5 cm phantom had the highest FOM at 50 kVp using 0.4 mm of Cu filtration. The 12 cm phantom had the highest FOM at 55 kVp using 0.9 mm Cu, and the 16 cm phantom had highest FOM at 55 kVp using 0.4 mm Cu. With regard to E, the 8.5 and 12 cm phantoms had the highest FOM at 50 kVp using 0.4 mm of Cu filtration, and the 16 cm phantom had the highest FOM at 50 kVp using 0.25 mm Cu. Antiscatter grid removal improved the FOM for a given set of x-ray conditions. Under aforesaid optimal settings, the 8.5 cm phantom FOM improved by 24% and 33% for ESD and E, respectively. Corresponding improvements were 26% and 24% for the 12 cm phantom and 6% and 15% for the 16 cm phantom. Conclusions: For pediatric patients, using 0.25-0.9 mm Cu filtration in the x-ray beam while maintaining 50-55 kVp, depending on patient size, provided optimal x-ray image quality to dose ratios. These settings, adjusted for x-ray tube loading limits and clinically acceptable image quality, should provide a useful strategy for optimizing iodine contrast agent based cardiac x-ray imaging. Removing the antiscatter grid improved the FOM for the 8.5 and 12 cm phantoms, therefore grid removal is recommended for younger children. Improvement for the 16 cm phantom declined into the estimated margin of error for the FOM; the need for grid removal for older children would depend on practical feasibility in the clinical environment.

60 APPLIED LIFE SCIENCES↗

Materials Data on Na5Cu2H14S4O19 by Materials Project

CuNa5CuH14S4O19 crystallizes in the monoclinic P2_1/c space group. The structure is three-dimensional and consists of four copper molecules and one Na5CuH14S4O19 framework. In the Na5CuH14S4O19 framework, there are five inequivalent Na1+ sites. In the first Na1+ site, Na1+ is bonded to six O2- atoms to form a mixture of edge and corner-sharing NaO6 octahedra. The corner-sharing octahedral tilt angles are 67°. There are a spread of Na–O bond distances ranging from 2.36–2.54 Å. In the second Na1+ site, Na1+ is bonded in a 5-coordinate geometry to five O2- atoms. There are a spread of Na–O bond distances ranging from 2.33–2.66 Å. In the third Na1+ site, Na1+ is bonded to six O2- atoms to form a mixture of edge and corner-sharing NaO6 octahedra. The corner-sharing octahedral tilt angles are 65°. There are a spread of Na–O bond distances ranging from 2.38–2.52 Å. In the fourth Na1+ site, Na1+ is bonded to six O2- atoms to form a mixture of distorted edge and corner-sharing NaO6 octahedra. The corner-sharing octahedral tilt angles are 67°. There are a spread of Na–O bond distances ranging from 2.35–2.60 Å. In the fifth Na1+ site, Na1+ is bonded to six O2- atoms to form a mixture of edge and corner-sharing NaO6 octahedra. The corner-sharing octahedral tilt angles are 65°. There are a spread of Na–O bond distances ranging from 2.40–2.54 Å. Cu+1.50+ is bonded in a 5-coordinate geometry to five O2- atoms. There are a spread of Cu–O bond distances ranging from 2.00–2.57 Å. There are fourteen inequivalent H1+ sites. In the first H1+ site, H1+ is bonded in a single-bond geometry to one O2- atom. The H–O bond length is 0.98 Å. In the second H1+ site, H1+ is bonded in a single-bond geometry to one O2- atom. The H–O bond length is 0.99 Å. In the third H1+ site, H1+ is bonded in a single-bond geometry to two O2- atoms. There is one shorter (1.00 Å) and one longer (1.76 Å) H–O bond length. In the fourth H1+ site, H1+ is bonded in a single-bond geometry to one O2- atom. The H–O bond length is 0.98 Å. In the fifth H1+ site, H1+ is bonded in a single-bond geometry to one O2- atom. The H–O bond length is 0.99 Å. In the sixth H1+ site, H1+ is bonded in a single-bond geometry to one O2- atom. The H–O bond length is 0.99 Å. In the seventh H1+ site, H1+ is bonded in a single-bond geometry to one O2- atom. The H–O bond length is 0.99 Å. In the eighth H1+ site, H1+ is bonded in a single-bond geometry to one O2- atom. The H–O bond length is 0.98 Å. In the ninth H1+ site, H1+ is bonded in a single-bond geometry to one O2- atom. The H–O bond length is 1.00 Å. In the tenth H1+ site, H1+ is bonded in a single-bond geometry to one O2- atom. The H–O bond length is 0.98 Å. In the eleventh H1+ site, H1+ is bonded in a single-bond geometry to one O2- atom. The H–O bond length is 1.00 Å. In the twelfth H1+ site, H1+ is bonded in a single-bond geometry to two O2- atoms. There is one shorter (1.00 Å) and one longer (1.75 Å) H–O bond length. In the thirteenth H1+ site, H1+ is bonded in a single-bond geometry to one O2- atom. The H–O bond length is 0.99 Å. In the fourteenth H1+ site, H1+ is bonded in a single-bond geometry to one O2- atom. The H–O bond length is 1.00 Å. There are four inequivalent S4+ sites. In the first S4+ site, S4+ is bonded in a trigonal non-coplanar geometry to three O2- atoms. There are a spread of S–O bond distances ranging from 1.49–1.55 Å. In the second S4+ site, S4+ is bonded in a trigonal non-coplanar geometry to three O2- atoms. There are a spread of S–O bond distances ranging from 1.49–1.55 Å. In the third S4+ site, S4+ is bonded in a trigonal non-coplanar geometry to three O2- atoms. There is one shorter (1.52 Å) and two longer (1.54 Å) S–O bond length. In the fourth S4+ site, S4+ is bonded in a trigonal non-coplanar geometry to three O2- atoms. There is two shorter (1.52 Å) and one longer (1.53 Å) S–O bond length. There are nineteen inequivalent O2- sites. In the first O2- site, O2- is bonded in a single-bond geometry to one S4+ atom. In the second O2- site, O2- is bonded in a distorted rectangular see-saw-like geometry to three Na1+ and one S4+ atom. In the third O2- site, O2- is bonded in a 4-coordinate geometry to two Na1+, one H1+, and one S4+ atom. In the fourth O2- site, O2- is bonded in a 4-coordinate geometry to two Na1+, one H1+, and one S4+ atom. In the fifth O2- site, O2- is bonded to three Na1+ and one S4+ atom to form distorted corner-sharing ONa3S tetrahedra. In the sixth O2- site, O2- is bonded in a distorted water-like geometry to one Na1+, one Cu+1.50+, and two H1+ atoms. In the seventh O2- site, O2- is bonded in a distorted water-like geometry to two equivalent Na1+ and two H1+ atoms. In the eighth O2- site, O2- is bonded in a distorted water-like geometry to one Na1+ and two H1+ atoms. In the ninth O2- site, O2- is bonded in a distorted water-like geometry to two Na1+ and two H1+ atoms. In the tenth O2- site, O2- is bonded in a distorted water-like geometry to one Na1+ and two H1+ atoms. In the eleventh O2- site, O2- is bonded in a water-like geometry to one Na1+ and two H1+ atoms. In the twelfth O2- site, O2- is bonded in a distorted water-like geometry to one Na1+ and two H1+ atoms. In the thirteenth O2- site, O2- is bonded in a distorted trigonal planar geometry to two Na1+ and one S4+ atom. In the fourteenth O2- site, O2- is bonded in a distorted trigonal planar geometry to one Na1+, one Cu+1.50+, and one S4+ atom. In the fifteenth O2- site, O2- is bonded to two Na1+, one Cu+1.50+, and one S4+ atom to form distorted ONa2CuS trigonal pyramids that share corners with two equivalent ONa3S tetrahedra and corners with two equivalent ONa2CuS trigonal pyramids. In the sixteenth O2- site, O2- is bonded to two Na1+, one Cu+1.50+, and one S4+ atom to form distorted ONa2CuS trigonal pyramids that share corners with two equivalent ONa3S tetrahedra and corners with two equivalent ONa2CuS trigonal pyramids. In the seventeenth O2- site, O2- is bonded in a distorted trigonal planar geometry to one Na1+, one Cu+1.50+, and one S4+ atom. In the eighteenth O2- site, O2- is bonded in a distorted trigonal planar geometry to two Na1+ and one S4+ atom. In the nineteenth O2- site, O2- is bonded in a single-bond geometry to one S4+ atom.

36 MATERIALS SCIENCE↗

Updates to the n+ 63,65 Cu Evaluations: RRR and Angular Distributions [Slides]

This work updates the evaluation of n+ 63,65 Cu for neutron energies in the resolved resonance region (RRR) and slightly higher energies. The updates strive to improve the statistical properties of the resonance parameters and the continuity of the evaluation between the RRR and the high-energy region while preserving or improving critical assembly benchmark performance. We will review our work on the resonance parameters and present the current status of our angular distribution analysis.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

NASA Tech Briefs, November 1995

The contents include: 1) Mission Accomplished; 2) Resource Report: Marshall Space Flight Center; 3) NASA 1995 Software of the Year Award; 4) Microbolometers Based on Epitaxial YBa2Cu3O(sub 7-x) Thin Films; 5) Garnet Random-Access Memory; 6) Fabrication of SNS Weak Links on SOS Substrates; 7) High-Voltage MOSFET Switching Circuit; 8) Asymmetric Switching for a PWM H-Bridge Power Circuit; 9) Better Ohmic Contacts for InP Semiconductor Devices; 10) Low-Bandgap Thermovoltaic Materials and Devices; 11) Digital Frequency-Differencing Circuit; 12) Imaging Magnetometer; 13) Computer-Assisted Monitoring of a Complex System; 14) Buffered Telemetry Demodulator; 15) Compact Multifunction Inspection Head; 16) Optical Detection of Fractures in Ceramic Diaphragms; 17) Eddy-Current Detection of Cracks in Reinforced Carbon/Carbon; 18) Apparent Thermal Conductivity of Multilayer Insulation; 19) Optimizing Misch-Metal Compositions in Metal Hydride Anodes; 20) Device for Sampling Surface Contamination; 21) Probabilistic Failure Assessment for Fatigue; 22) Probabilistic Fatigue and Flaw-Propagation Analysis; 23) Windows Program for Driving the TDU-850 Printer; 24) Subband/Transform MATLAB Functions for Processing Images; 25) Computing Equilibrium Chemical Compositions; 26) Program Processes Thermocouple Readings; 27) ICAN-Second-Generation Integrated Composite Analyzer; 28) Integrated Composite Analyzer with Damping Capabilities; 29) Computing Efficiency of Transfer of Microwave Power; 30) Program Calculates Power Demands of Electronic Designs; 31) Cost-Estimation Program; 32) Program Estimates Areas Required by Electronic Designs; 33) Program to Balance Mapped Turbopump Assemblies; 34) BiblioTech; 35) Controlling Mirror Tilt With a Bimorph Actuator; 36) Burst-Disk Device Simulates Effect of Pyrotechnic Device; 37) Bearing-Mounting Concept Accommodates Thermal Expansion; 38) Parallel-Plate Acoustic Absorbers for Hot Environments; 39) Adjustable-Length Strut Withstands Large Cyclic Loads; 40) Tool Indicates Contact Angles in Bearing Raceways; 41) Gravity Slides With Magnetic Braking; 42) High-Torque, Lightweight, Pneumatically Driven Wrench for Small Spaces; 43) Device for Testing Compatibility of an O-Ring; 44) Magnetic Heat Pump Containing Flow Diverters; 45) Variable-Tilt Helicopter Rotor Mast; 46) "Beach-Ball" Robotic Rovers; 47) Apparatus Would Measure Temperatures of Ball Bearings; 48) Flexible Borescope for Inspecting Ducts; 49) Texturing Copper To Reduce Secondary Emission of Electrons; 50) Automated Laser Cutting in Three Dimensions; 51) Algorithm Helps Monitor Engine Operation; 52) Flexible Revision of Data-Processing Communications; 53) Software for Managing the Use of Land; 54) Thermal Strap Increases Cryocooling Efficiency; 55) Reversible Nut With Engagement Indication; 56) Control Algorithms for Kinematically Redundant Manipulators; 57) Computed Hydrogen-Flow Splits in a Rocket Engine; 58) Pressure and Thermal Modeling of Rocket Launches; 59) Field of View of a Spacecraft Antenna: Analysis and Software; 60) Digital Controller for Laser-Beam-Steering Subsystem; 61) More About Beam-Steering Subsystem for Laser Communication; 62) Digital Controller for Laser-Beam-Steering Subsystem: Part 2; 63) Interface Circuit Board for Space-Shuttle Communications; 64) Automated Planning of Spacecraft Telecommunications; 65) Artifacts of Spectral Analysis of Instrument Readings; 66) Neural-Network Controller for Vibration Suppression; 67) Adaptive Finite-Element Computation in Fracture Mechanics; 68) Attitude Control for the Cassini Spacecraft; 69) Analytical Model for Fluid Dynamics in a Microgravity Environment; 70) Study of Rocket-Engine Joints Bonded by NVCU/NARloy-Z; 71) Improved Silicon Nitride for Advanced Heat Engines; 72) Parameters for Welding Aluminum/Lithium Alloys; 73) Lightweight Composite Intertank Structure; 74) Foil Patches Seal Small Vacuum Leaks; 75) Data Base on Cables and Connectors; 76) Effect of Clock Mode on Radiation Hardnessf an ADC; and 77) Fault-Tolerant Control for a Robotic Inspection System.

Source record↗

Physicochemical investigations of carbon nanofiber supported Cu/ZrO{sub 2} catalyst

Zirconia-promoted copper/carbon nanofiber catalysts (Cu‐ZrO{sub 2}/CNF) were prepared by the sequential deposition precipitation method. The Herringbone type of carbon nanofiber GNF-100 (Graphite nanofiber) was used as a catalyst support. Carbon nanofiber was oxidized to (CNF-O) with 5% and 65 % concentration of nitric acid (HNO{sub 3}). The CNF activated with 5% HNO{sub 3} produced higher surface area which is 155 m{sup 2}/g. The catalyst was characterized by X-ray Diffraction (XRD), Fourier Transform Infra-Red (FTIR) and N{sub 2} adsorption-desorption. The results showed that increase of HNO{sub 3} concentration reduced the surface area and porosity of the catalyst.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microbial Approach to Low-Cost Production of Photovoltaic Nanomaterials

Photovoltaic (PV)-generated electricity can participate in renewable grid parity after meeting conditions of low-cost PV materials and economic manufacturing of solar cells. In this paper, we report low-cost, scalable microbial synthesis of Cu(In,Ga)Se 2 (CIGSe) and Cu(In,Ga)S 2 (CIGS), which are among the promising candidates to serve as light absorbing layers in solar panels. Microbial synthesis uses reducible chalcophiles and empirically stoichiometric metal components to produce CIGSe and CIGS with band gaps and intra- and intercrystallite compositional homogeneity similar to that produced with traditional techniques. Importantly, microbially produced photovoltaic materials described herein use inexpensive precursor materials at moderate temperatures (65 °C). The microbially facilitated processes do not utilize high temperature, vacuum, or toxic organic solvents. The potential to upscale microbial synthesis without loss of material quality is demonstrated here, indicating a high potential for industrial applications of this technology for production of nanomaterials for PV applications. We estimate that a 50 000 gallon fermentor could generate about 100 kg/month of CIGSe nanoparticles, which could be processed into 0.2 MW of PV cells.

stoichiometric homogeneity↗