Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CO 2 capture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Performance of hydrophobic physical solvents for pre-combustion CO 2 capture at a pilot scale coal gasification facility

Here, in this paper, we present the first pilot plant data for hydrophobic physical solvents for CO 2 and H 2 S removal from coal-derived H 2 -rich syngas. Four physical solvents were tested under pre-combustion CO 2 capture conditions at bench scale and pilot plant scale: one baseline hydrophilic solvent and three hydrophobic solvents. The solvents were: (1) polyethylene-glycol-dimethyl ether (PEGDME), a hydrophilic solvent analog for the commercial process Selexol, (2) tributyl- phosphate (TBP), a commercially available hydrophobic solvent, (3) polyethylene glycol-poly(dimethylsiloxane) (PEG-PDMS-3), and (4) diethyl sebacate (CASSH-1), a novel, computationally screened hydrophobic solvent developed by the National Energy Technology Laboratory (NETL). All solvents were studied under pure gas (CO 2 /N 2 /H 2 /CH 4 ) equilibrium conditions at NETL followed by pilot plant testing with syngas at the University of North Dakota Energy & Environmental Research Center (UND EERC). Long term performance of CASSH-1 and PEDGME was then assessed with results compared to process simulation predictions. Within experimental uncertainties, all solvents showed comparable CO 2 absorption performance at above room temperature operation while the hydrophobic solvents had limited water uptake and low vapor pressure, which alleviates concerns related to corrosion, water absorption, and solvent loss to evaporation. These results indicate low viscosity, low vapor pressure hydrophobic solvents are a promising option for lower cost CO 2 capture from high pressure syngas applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Enhancing membrane performance for CO 2 capture from flue gas with ultrahigh MW polyvinylamine

Membranes for post-combustion CO 2 capture are required to have a high CO 2 permeance due to the limited driving force. For facilitated transport membranes synthesized with polyvinylamine (PVAm), a defect-free selective layer of <200 nm is usually required to render sufficient permeance with high CO 2 /N 2 selectivity. In order to meet such a demand through the knife-coating process, the coating solution needs to have a high viscosity at a relatively low concentration to minimize its penetration into the substrate. The demand was met by synthesizing PVAm with an ultrahigh molecular weight (MW) via inverse emulsion polymerization (IEP) in this study. Compared to solution polymerization, IEP isolates the reaction in inverse micelles suspended in a continuous organic phase, which allows excellent dissipation of the heat generated by the reaction and reduces gel formation drastically. The polymerization parameters, including monomer concentration, initiator concentration, and reaction temperature, were investigated to obtain the optimal MW of PVAm for membrane performance. As compared to solution polymerization, IEP enhanced the MW of PVAm from 1.2 to 12.7 MDa, which minimized the penetration of the coating solution into the substrate and hence the extra mass transfer resistance. The effect of MW and degree of hydrolysis of PVAm on the membrane transport properties were studied. Furthermore, by employing PVAm with a MW of 12.7 MDa to strengthen the polymer matrix, the loading of piperazine glycinate in the membrane was increased up to 85 wt.%. In conclusion, the resultant membrane achieved a CO 2 permeance of 839 GPU and a CO 2 /N 2 selectivity of 161 at the typical flue gas temperature of 57°C.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2023

Development of a Pre-Combustion CO 2 Capture Process Using High-Temperature PBI Hollow-Fiber Membranes

The overall objective of this project was to evaluate the advantages of transformational polybenzimidazole (PBI) polymer hollow-fiber membrane (HFM)-based, carbon dioxide (CO 2 ) capture and purification technology at bench-scale using an actual coal-derived syngas stream from a coal gasification facility. The project was carried out over two budget periods. The technical objectives in Budget Period 1 (BP1) included preparing HFs and modules and upgrading the available skid for field testing. The technical objectives for BP2 were to field-test the skid unit with actual coal-derived syngas from an oxygen-blown gasifier to obtain performance data, update the Techno-Economic Analysis (TEA) that would assist with future process scale-up, and provide information on the design of a small pilot-scale test unit. The goal was to advance the PBI-HFM CO 2 capture and gas separation system for pre-combustion applications beyond second-generation economic performance predictions and make progress toward meeting overall fossil energy performance goals of CO 2 capture with 95% CO 2 purity at a cost of electricity (COE) 30% less than baseline capture approaches. The research program was designed with progressive technical tasks leading to both dynamic and steady-state testing of the PBI-HFM skid with actual coal-derived syngas. The work plan was to: (1) fabricate sufficient Generation-2 (GEN-2) fibers for module fabrication; (2) upgrade the fiber skid to accommodate large fiber modules for bench-scale field testing; (3) conduct dynamic and steady-state testing with coal-derived syngas from an oxygen-blown gasifier and obtain system performance data; (4) perform a TEA and environmental, health, and safety (EH&S) assessment; (5) update the State-Point Data Table, Technology Gap Analysis (TGA), and Technology Maturation Plan (TMP); (6) uninstall and return the test skid to the Recipient’s facilities; and (7) submit a Final Report that describes the results and analysis of the project research effort.

03 NATURAL GAS↗
DOE OSTI2020

Sorption Enhanced Mixed Matrix Membranes for Hydrogen (H 2 ) Purification and Carbon Dioxide (CO 2 ) Capture

The technical objective of this project was to develop sorption enhanced mixed matrix membranes with H 2 permeance of 500 gas permeance units (GPU) and H 2 /CO 2 selectivity of 30 at 150-200 °C. These membranes will be the central component in the design of membrane based systems for 90% capture of CO 2 from coal-derived syngas, with 95% CO 2 purity at a cost of electricity 30% less than baseline capture approaches. The unique approach in this proposal is to design crosslinked polymers containing Pd-based nanoparticles achieving strong H 2 sorption and size sieving ability and thus H 2 /CO 2 selectivity. The specific objectives for each budget period (BP) are described below. BP 1: Identify polymer matrix with strong size sieving ability and palladium (Pd)-containing nanomaterials to prepare freestanding mixed matrix films with H 2 permeability of 50 Barrer and H 2 /CO 2 selectivity of 30 at 150-200°C with simulated syngas. BP 2: Prepare and optimize thin film mixed matrix composite membranes materials with H 2 permeance of 500 GPU and H 2 /CO 2 selectivity of 30 at 150-200 °C, and complete the modification of the membrane test unit for the field test in the BP 3. BP 3: Conduct a 20-day field test of the membranes with real syngas at Center for Advanced Energy Research (CAER) of the University of Kentucky (UKy). During the BP2, we have successfully prepared thin-film composite (TFC) membranes based on mixed matrix materials (MMMs) containing Pd nanoparticles in polymers, and demonstrated their superior and robust performance for H 2 /CO 2 separation at 150 – 225 °C. (1) Production of the Pd based nanoparticles with a diameter of 4 nm has been scaled up to 200 mg/day. (2) We have prepared TFC membranes with H 2 permeance above 500 GPU and H 2 /CO 2 selectivity above 30 at temperatures up to 225 °C, which meet the targets for the BP2. (3) We have conducted parametric studies of TFC membranes with a mixed gas containing H 2 S and H 2 O and demonstrated the stability of the membranes. (4) We have established a new testing plan at the Center for Advanced Energy Studies (CAER) at the University of Kentucky because NCCC decided to shut down their gasifier. During this project, four Ph.D. students received the inter-disciplinary training and graduated, including Shailesh Konda, Maryam Omidvar, Deqiang Yin, and Lingxiang Zhu. One postdoctoral researcher (Dr. Liang Huang) and two Ph.D. students (Abhishek Kumar and Hien Nguyen) are involved in this project. The project leads to one provisional patent application, eight peer-reviewed articles, and one manuscript in preparation. The details are shown below.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Advanced Integrated Reticular Sorbent-Coated System to Capture CO 2 from the Atmosphere (AIR2CO2)

GE Research Center (GRC) and the University of California, Berkeley (UCB) executed an 15-month, $1.0 MM program to develop a lab-scale material system to extract CO 2 from ambient air using UCB’s pioneering sorbent technology and GRC’s composite coating expertise. The primary objective of this project was to develop an “Advanced Integrated Reticular Sorbent-Coated System to Capture CO 2 from the Atmosphere (AIR2CO2)” at a Technology Readiness Level (TRL) of 3. The AIR2CO2 concept relies on two key innovations: 1) advanced sorbent architectures with high capacity and rapid sorption kinetics that enable effective CO 2 capture at low concentrations, and 2) tailored MOF-binder slurry formulations and coating processes that enable sorbent integration into a novel additively-manufactured contactor.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Engineering-Scale Validation of Novel Algae CO 2 Capture and Bioproducts Technology

The purpose of this project was to advance and scale the algae-based technology Helios-NRG has been developing for capture of CO 2 from the flue gas of coal-burning power plants with conversion of the CO 2 to high-value products. In order to encourage the process becoming commercial and be adoptable, it is essential that the cost of CO 2 be close to net zero or slightly revenue positive. Two methods to achieve this are reducing the cost of operations through efficiencies and selling of products derived from conversion. Helios and the project team partners have accomplished the goals of furthering the technology to be more scalable and substantially lower cost with a defined pathway for commercialization.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Joint Theoretical and Experimental Study of the Electronic, Magnetic, and Lattice Phonon Dynamics Properties of Ca x Fe y O z Compounds Applied to CO 2 Capture

Unleashing energy innovation ensures a resilient and reliable energy supply. There is a critical need for the development of new carbon dioxide (CO 2 ) captors that have improved energy efficiency accompanied by lower capital and operational costs to ensure abundant, affordable, and secure energy. Among solid materials, CaO is a good CO 2 sorbent for capture technology due to its wide availability and low cost. However, CaO also suffers from some disadvantages, such as high calcination temperature, decreasing capability due to sintering, attrition, and reaction with SO x and NO x . In this study, we employed an ab initio thermodynamic approach and experimental measurements to improve its CO 2 capture performance during the cycles. To do so, we explored the electronic, magnetic, and lattice dynamic properties of a series of calcium ferrites (Ca x Fe y O z ) and applied them for CO 2 capture. Our results showed that all of them can thermodynamically react with CO 2 to form CaCO 3 and iron oxides. Compared to pure CaO capturing CO 2 , CaFe 3 O 4 , CaFe 2 O 4 , and Ca 2 Fe 2 O 5 could shift the CO 2 regeneration temperature to a lower range. The experimental measurements showed that CaFeO 2 is a good CO 2 captor with or without the presence of an O 2 presence. The calculated thermodynamic properties of Ca x Fe y O z capturing the CO 2 reactions can be used to find their operational temperature ranges for different CO 2 capture technologies.

CO2 capture↗
DOE OSTI2024

Unveiling the porosity effect of superbase ionic liquid-modified carbon sorbents in CO 2 capture from air

Direct air capture (DAC) of CO 2 represents one of the most promising technologies to achieve negative carbon emissions. In this work, the superbase ionic liquids (ILs)-modified carbon substrates were developed for DAC of CO 2 by harnessing the strong CO 2 binding capability of IL and the ordered porous channels of the carbon supports. Detailed porosity analysis revealed that the IL with an aromatic cation and an oxygenate anion preferred to fill the micropores, and a thin layer was created on the surface of the mesopores. Strong π-π interaction between the IL layer and the carbon surface was disclosed by wide-angle X-ray scattering (WAXS) analysis, leading to enhanced thermal stability of the IL phase. For the same lL coating amount, the DAC of CO 2 evaluation revealed that a larger mesopore size and pore volume in the carbon/IL composite materials led to higher CO 2 uptake capacity by exposing more active sites to integrate CO 2 from diluted sources. Further, the thermodynamic analysis confirmed the critical role of IL coating in providing strong chemisorption sites and significantly improved selectivity to enrich the diluted CO 2 from the air atmosphere. This work provides guidance on leveraging the scaffolds' surface properties and porosities of the scaffolds to optimize DAC of CO 2 behavior.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Plastic Additive, Sorbent-Coated, Thermally Integrated Contactor for CO 2 Capture (PLASTIC4CO2) (Final Report)

Final report for Plastic Additive, Sorbent-Coated, Thermally Integrated Contactor for CO2 Capture (PLASTIC4CO2) DE-FE-0032132. The goal of the work was to investigate at a technology readiness level of 3 (TRL 3), the proof of concept of an additively printed plastic 2-channel heat exchanger/sorbent contactor system to achieve a 15% lower levelized cost of electricity (LCOE) than a baseline liquid phase amine adsorber system for 90% and 95% capture of CO 2 from both a 7F02 2x1CC and 7HA02 2x1CC natural gas turbines.

03 NATURAL GAS↗
DOE OSTI2025

Long-Range Metal–Sorbent Interactions Determine CO 2 Capture and Conversion in Dual-Function Materials

Carbon capture and utilization involve multiple energy- and cost-intensive steps. Dual-function materials (DFMs) can reduce these demands by coupling CO 2 adsorption and conversion into a single material with two functionalities: a sorbent phase and a metal for catalytic CO 2 conversion. The role of metal catalysts in the conversion process seems salient from previous work, but the underlying mechanisms remain elusive and deserve deeper investigation to achieve maximum utilization of the two phases. Here, for this work, preformed colloidal Ru nanoparticles were deposited onto a “NaOx”/Al 2 O 3 sorbent to prepare prototypical DFMs with controlled phases for CO 2 capture and hydrogenation to CH 4 . Ru addition was found to double the high-temperature CO 2 adsorption capacity by activating the “NaOx”/Al 2 O 3 sorbent phase during a reductive pretreatment step. Most importantly, low Ru loadings were sufficient to ensure maximum CO 2 adsorption and conversion. This was attributed to the key role of the metal–sorbent interactions, wherein Ru was required to hydrogenate strongly bound CO 2 on the “NaO x ”/Al 2 O 3 sorbent to CH 4 via the H 2 activated on Ru. This interaction facilitated rate-determining carbonate migration and subsequent hydrogenation at the metal–sorbent interface. Overall, Ru controlled the CO 2 hydrogenation reaction rate, while the “NaO x ”/Al 2 O 3 sorbent dictated the CO 2 uptake capacity. By controlling metal–sorbent interactions at the molecular level, we demonstrate the critical role of the two phases and their synergy, facilitating the design of DFMs with maximum CO 2 capture and conversion efficiency.

carbon capture↗
DOE OSTI2025

Second generation non-aqueous solvents (gen2nas) for co 2 capture from natural gas combined cycle plants

This final technical report submitted to DOE/NETL presents all the research activities performed during the Cooperative Agreement DE-FE0032218 entitled Second Generation Non-Aqueous Solvents (GEN2NAS) for CO 2 Capture from Natural Gas Combined Cycle Plants, which spanned from April 2023 through March 2025. In this project, Research Triangle Institute (RTI) International has developed the second-generation of its non-aqueous solvent (NAS), herein referred to as GEN2NAS, to remove carbon dioxide (CO 2 ) from natural-gas combined cycle (NGCC) flue gas. The technology aims to substantially reduce the cost of CO 2 capture while minimizing the environmental impacts through lower secondary emissions and wastewater generated from the CO 2 capture plant.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2026

Optimal Design and Techno-Economic Analysis of 3D-Printed, Intensified Packings for Absorbers and Strippers in Solvent-Based CO 2 Capture

A potential technology for the CO 2 absorption process is utilizing intensified structured packing with embedded cooling/heating channels for continuous heat exchange, which can overcome limitations of discrete methods, such as discrete intercooling and centralized reboilers, to aid in reducing energy consumption and decreasing costs. This work investigates the modeling of intensified packing (IP) for the stripper tower, extending on previous work for the absorber, which distributes heat internally within the column, improving the thermodynamics for the solvent regeneration process. The model includes submodels for steam turbine extraction to produce steam at various qualities as well as a surrogate model for calculating steam enthalpy. A cost model for a plant-scale absorption capture process was developed, allowing for the design of the plant to be optimized, subject to minimizing capture cost using two different power plant flue gas sources. In this optimization, the placement of IP in both towers is optimized to balance the trade-off between enhanced heat transfer and reduced mass transfer volume. For natural gas combined cycle flue gas, the standard process configuration had a minimum cost of $\$$65.40/tonne CO 2 , and considering IP, the minimum capture cost is reduced to $\$$62.73/tonne, with utilization in the stripper column, which reduces yearly costs by up to $\$$2.67 MM/yr. Cooling the absorber through IP, or intercoolers, was only found to be beneficial at higher capture rates, with IP in both towers having a cost of capture of $\$$68.08/tonne at 99.9% capture, a reduction of $\$$12.64/tonne when using only intercoolers at the same capture rate. When capturing from pulverized-coal power plants, the minimum cost of capture when using IP in both towers is $\$$44.18/tonne (at 97% capture), while the standard configuration with and without intercoolers was $\$$45.69 and $\$$47.22 per tonne, respectively. This results in a reduction in yearly costs of $\$$16.98 MM/yr from the base-case configuration. At this higher CO 2 concentration, cooling in the absorber from the IP becomes extremely beneficial, reducing energy consumption by up to 6%.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2023

Experimental measurement of the effective contact angle for solvent/packing interactions in a structured packed column for CO 2 capture

The contact angle is a critical factor for determining the effective mass transfer area for carbon dioxide (CO 2 ) capture via the chemical absorption process in a packed column, and thus the overall capture efficiency of the packed column. Many widely used commercial packings involve microscale features (perforation, corrugation, etc.) that may also affect the wetting behavior. This study proposes a systematic method of using a modified Wilhelmy plate to measure the effective contact angle to characterize the solvent and featured packing interaction. In lieu of computational efforts relying on assumptions guided by semi-informed correlation, the proposed method directly measures the effective contact angle as a function of the solvent and packing thermophysical and hydrodynamic properties. The characterization of the effective contact angle is then integrated in the computational fluid dynamics modeling to reduce uncertainty in the prediction of effective mas transfer area. Experiments were conducted for stainless steel coupons using water and aqueous sodium hydroxide (NaOH) solvent for verification of the proposed experimental protocol. The surface tension of the aqueous NaOH solvent was altered using surfactant and antifoam. The effective contact angle increases with the increased value of the surface tension for flat stainless steel sheets. On the other hand, effective contact angles do not vary in Mellapak coupons for aqueous monoethanolamine (MEA) and NaOH solvent. In this case, surface textures and sheet design play a dominant role in the surface tension of solvents. Furthermore, CO 2 loading has a significant effect on the contact angle for Mellapak coupons. As expected, the contact angle decreases with the increasing temperature of CO 2 capture solvents (MEA, EEMPA). The effective contact angle measurement using the Wilhelmy plate method can provide more accurate and efficient solvents for characterizing the solvent-packing surface interactions. Subsequently, the present method enhances the accuracy of the prediction of the effective mass transfer area in carbon capture by solvent absorption.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Initial Engineering and Design for CO 2 Capture from Ethanol Facilities

The Energy & Environmental Research Center, in partnership with the U.S. Department of Energy (DOE) and North Dakota ethanol producer Red Trail Energy, LLC (RTE) and with technical support from Trimeric Corporation and the KLJ engineering firm, completed an initial engineering design (IED) for a hybrid capture system to estimate associated costs for retrofitting the operational RTE ethanol plant. The project goal supports the DOE objective to achieve negative emissions using commercially available technologies to attain Technology Readiness Level 6+ from a facility emitting >100,000 tonnes of carbon dioxide (CO 2 ) annually. The RTE CCS (carbon capture and storage) Project is currently operating a CO 2 capture facility, adjacent to the RTE ethanol facility in western North Dakota, and injecting the CO 2 more than a mile below RTE property for permanent storage. This novel hybrid capture system would process about 310,000 tonnes of CO 2 annually for the RTE host site and includes CO 2 capture and compression from bioprocessing as well as capturing CO 2 produced from natural gas boilers. The bioprocessing capture process, based on past RTE studies investigating ammonia liquefaction technology with CO 2 produced from natural gas boilers captured utilizing chemical absorption with amine, was shown to be technically feasible for the RTE site. Activities conducted to support the project goal included 1) designing a hybrid capture system using CO 2 emissions from both bioprocessing and heat production at the host site facility; 2) conducting a pre-front-end engineering and design analysis of the hybrid capture system to include environmental health and safety, a constructability report, identification of permits, and corporate approvals; and 3) performing a techno-economic assessment in accordance with DOE’s methodology, as demonstrated by the bituminous baseline study. In addition, a life cycle assessment (LCA) was completed for the RTE site to estimate the carbon life cycle for ethanol-CCS implementation using the designed hybrid capture system to determine potential for net-negative carbon emissions. Results of the IED showed the hybrid system to be technically viable, with a moderate estimated cost of $55/tonne CO 2 captured for the hybrid system. The cradle-to-gate LCA showed preliminary net-negative carbon emissions potential anticipated from implementing a hybrid CCS system at a commercial scale. Recommended next steps toward potential implementation include hybrid capture system demonstration testing for detailed engineering and LCA model comparisons with low-carbon fuel incentive programs for financial support.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Regenerable solvents mediate accelerated low temperature CO 2 capture and carbon mineralization of ash and nano-scale calcium carbonate formation

The dual need to remove CO 2 from our emissions and treat alkaline industrial residues such as ash materials motivate the design of innovative pathways to simultaneously capture and convert CO 2 into mineralized carbonates. Direct carbon mineralization is one approach that addresses the need to simultaneously treat alkaline industrial residues and mineralize CO 2 emissions. Low CO 2 solubility in water and slow kinetics at ambient temperature have challenged the direct carbon mineralization of alkaline industrial residues. Here, to address these challenges, the use of CO 2 capture solvents that enhance CO 2 solubility and facilitate accelerated carbon mineralization of fly ash at temperatures below 90 °C is investigated. Calcium carbonate formation results in the inherent regeneration of the solvent. The carbon mineralization extents of non-calcium carbonate content in fly ash were 50% and 51% and in waste ash were 58% and 62% in 2.5 M sodium glycinate and 30 wt% MEA solutions, respectively. The experiments were performed at 50 °C for 3 hours with CO 2 partial pressure of 1 atm in a continuously stirred slurry environment with 15 wt.% solid. Furthermore, nanoscale CaCO 3 is successfully synthesized from dissolved calcium using CO 2 -loaded sodium glycinate and surfactants such as CTAB (Cetyl Trimethyl Ammonium Bromide). Surfactants such as CTAB bind to the calcium carbonate surface and regulate the growth of calcium carbonate particles. These innovative approaches demonstrate the feasibility of directly storing CO 2 in fly ash and waste ash as calcium carbonate and producing nanoscale calcium carbonate using regenerable CO 2 capture solvents.

42 ENGINEERING↗
DOE OSTI2023

Highly Tunable Syngas Product Ratios Enabled by Novel Nanoscale Hybrid Electrolytes Designed for Combined CO 2 Capture and Electrochemical Conversion

Coupling renewable energy with the electrochemical conversion of CO 2 to chemicals and fuels has been proposed as a strategy to achieve a new circular carbon economy and help mitigate the effects of anthropogenic CO 2 emissions. Liquid-like Nanoparticle Organic Hybrid Materials (NOHMs) are composed of polymers tethered to nanoparticles and are previously explored as CO 2 capture materials and electrolyte additives. Here, in this study, two types of aqueous NOHM-based electrolytes are prepared to explore the effect of CO 2 binding energy (i.e., chemisorption versus physisorption) on CO 2 electroreduction over a silver nanoparticle catalyst for syngas production. Poly(ethylenimine) (PEI) and Jeffamine M2070 (HPE) are ionically tethered to SiO 2 nanoparticles to form the amine-containing NOHM-I-PEI and ether-containing NOHM-I-HPE, respectively. At less negative cathode potentials, PEI and NOHM-I-PEI-based electrolytes produce CO at higher rates than 0.1 molal. KHCO 3 due to favorable catalyst-electrolyte interactions. Whereas at more negative potentials, H 2 production is favored because of the carbamate electrochemical inactivity. Conversely, HPE and NOHM-I-HPE-based electrolytes display poor CO 2 reduction performance at less negative potentials. At more negative potentials, their performance approached that of 0.1 molal. KHCO 3 , highlighting how the polymer functional groups of NOHMs can be strategically selected to produce value-added products from CO 2 with highly tunable compositions.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Unlocking liquid chemisorption in solid matrices: immobilized deep eutectic solvent-ZIF-8 composites for next-generation CO 2 capture

Achieving net-zero emissions by 2050 requires scalable and durable CO 2 capture solutions, with direct air capture (DAC) gaining increasing prominence. Deep eutectic solvents (DESs) have emerged as promising candidates due to their strong chemisorptive properties, but their liquid-phase nature limits integration into solid systems. In this study, we introduce a solid–liquid hybrid approach by immobilizing [TEAB][TEPA] 2 , a highly CO 2 -reactive DES, onto various supports via non-covalent immobilization. This strategy induces solid-like behavior while retaining molecular-level reactivity of the DES. Among the supports including ZIF-8, zeolite Y, zirconia, and alumina, the [TEAB][TEPA] 2 @ZIF-8-56% composite demonstrated promising CO 2 uptake capacity of 2.00 mmol g −1 adsorbent at 1 bar, 1.48 at 0.15 bar, 0.96 at 0.01 bar, and 0.59 at 0.4 mbar. Particularly, we can observe that the chemisorption capacity under 400 ppm conditions is successfully introduced into ZIF-8, whereas pristine ZIF-8 showed negligible uptake under these same conditions. Breakthrough experiments confirmed robust capture behavior under humid conditions. The composite exhibited excellent cycling stability over 100 capture-release cycles, supported by thermogravimetric analysis. In situ DRIFTS verified that the chemisorptive nature of the DES remained intact after immobilization. Additional characterization studies, including FTIR, PXRD, N 2 physisorption, and XPS depth profiling, revealed partial DES infiltration and strong interfacial interactions. Comparative results using alumina-based composites underscored the importance of microporosity in stability. Finally, these findings suggest that DES-MOF composites hold promise as carbon capture materials, bridging liquid-phase functionality and solid-state robustness.

Yoo, Yunsung [Northwestern Univ., Evanston, IL (Un↗
DOE OSTI2023

Impact of Hydrogen Bonds on CO 2 Binding in Eutectic Solvents: An Experimental and Computational Study toward Sorbent Design for CO 2 Capture

Choline-based amino acid ionic liquids with anions glycinate, β-alaninate, phenylalaninate, and prolinate were synthesized and mixed with ethylene glycol to form lower-viscosity benign eutectic solvents for CO 2 capture. The highest capacity measured was 0.7 moles of CO 2 per mole of ionic liquid (2 moles CO 2 per kg solvent) for a 1 to 2 mole ratio mixture of choline prolinate to ethylene glycol at 1 bar of CO 2 and 25 °C. Under 5000 ppm of CO 2 , half of this capacity was realized. Here, through a combined study of quantitative 13 C NMR spectroscopy, molecular dynamics simulations and density functional theory calculations, we show that hydrogen bonding in the eutectic solvent prevents proton-transfer between prolinate anions upon CO 2 absorption, which occurs in the absence of ethylene glycol and deactivates binding sites. Blocking this proton transfer leads to a higher binding capacity compared to neat choline prolinate. This work demonstrates the impact of hydrogen bonding on the CO 2 binding mechanism and energetics, as well as physical and thermal properties in eutectic solvents, thus addressing an unmet need and informing future studies on the development of benign sorbents for capturing CO 2 from dilute streams.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗