Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BOREHOLES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Interpretation of borehole strain measurements using surrogate modeling-based optimization

Interpreting strain data measured during well testing requires inverting poroelastic forward models set up to represent an aquifer or reservoir. One approach is to use stochastic methods to conduct the inversion. Subsurface parameters such as elastic modulus, permeability, and geometry of heterogeneities are estimated by searching the parameter space. This is feasible, but cumbersome, requiring more than a week of computation using many hundreds of computer nodes in one of our earlier analyses. This motivated us to consider alternative methods, including an artificial neural network (ANN) as a surrogate model.

Roudini, Soheil↗
DOE OSTI2023

Triaxial Shear Tests on Simulated Sierra White Fault Gouge & Borehole Simulation in Sierra White Gouge

Laboratory shear tests were conducted on pulverized Sierra White granite (SWG) to investigate slip mechanisms in naturally occurring faults. Synthetic fault geometries were constructed by sandwiching fine grained SWG powder in between steel forcing blocks. For dry experiments, ~3.5 g of SWG powder was poured onto the face of the lower steel forcing block and leveled. For saturated experiments, enough fluid was added to the ~3.5 g of Sierra White granite powder to form a slurry. This slurry was applied to the lower forcing block and leveled. Inclined forcing blocks with 25.4 mm diameter and 35° faces, which were machined from ground steel rods with fine teeth on the faces, help to hold the gouge in place and prevent delamination at the interface. The top forcing block had a 2.03 mm centered hole to allow pore fluid access to the gouge. A fine steel mesh prevented back flow of the gouge into pore fluid lines. Samples were isolated from the confining medium using three layers of heat shrink polyolefin, as shown in Figure 1. The outer layer was shrunk over the o-rings on the end caps to form an impermeable seal, which was reinforced with steel tie wires on both sides of the o-rings. Hardened steel spacers and copper shim stock was placed between the steel forcing blocks and the end caps to preserve the parallelism of the Hastelloy wetted parts. For dry samples, the end caps were plugged, while the end caps for the saturated samples were connected to pore lines.

58 GEOSCIENCES↗
DOE OSTI2024

Microbial Analysis of 100-N Borehole Samples: Estimation of Diesel and BTEX Degrading Bacterial Populations

Historical unplanned releases at the UPR-100-N-17 166-N Diesel Oil Supply Line Leak waste site located within the 100-NR-1 OU resulted in diesel fuel contamination of the unsaturated vadose zone and site groundwater. Enhanced in situ bioremediation of the deep vadose zone was the final remedy decision for the 100-NR-1 Operable Unit (OU) and the full-scale bioventing demo began in 2012. For this remedy, oxygen is actively supplied to the deep vadose zone to stimulate aerobic hydrocarbon degrading microorganisms to metabolize petroleum contamination. Degradation rate calculations based on vadose zone respirometry measurements, however, have indicated declining activity over recent years, though the precise reason for this apparent decline has not been determined. In this investigation 100-NR-1 OU sediment cores were analyzed for total microbial biomass, as well as enumeration of diesel and BTEX degrading bacteria to determine if these microbial populations have declined relative to previous measurements taken in 2009.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Ground heat exchanger design tool with rowwise placement of boreholes

Simulation-based design tools have been used since the late 1980s for designing ground heat exchangers (GHE) used with ground source heat pump (GSHP) systems. The ground heat exchanger simulations used in these tools rely on thermal response functions known as g-functions. Because of the significant computational burden in computing g-functions for even a single configuration, the design tools have relied on libraries of pre-computed g-functions. These g-functions were available for standard configuration shapes, such as lines, rectangles, open rectangles, L-shapes, and U-shapes. Standard shapes are often sub-optimal. For any building on a site, the available land may preclude use of a standard shape. For large GSHP systems with significantly imbalanced annual heat rejection and extraction loads, large rectangular fields may experience significant heat build-up (or heat draw-down) in the interior of the field. This paper describes a new ground heat exchanger design tool capable of automatically selecting and sizing both standard and irregular configurations. The focus of this paper is a method for creating, selecting and sizing irregular configurations where the available land area and "no-go" zones are described as irregular polygons.

Spitler, Jeffery↗
NASA NTRS1978

The measurement of long period and secular deformation with deep borehole tiltmeters

Two clusters of instruments were emplaced in fractured bedrock in eastern Massachusetts in 1970 and 1975. The intrasite agreement at tidal periods was about two percent, but there is no agreement at longer periods. A strong temperature-induced annual component ranging from 3 to 15 urads was present on instruments installed at depths of 15-20m; it was not apparent on those at 100-120m. One instrument, in continuous operation for three years at 100m, showed a net drift of 0.3 urads down to the SW, with a maximum departure of 2.0 urads from the trend. Pore pressure variations, material corrosion and creep, and local movements are apparently the limiting factors to long-term measurements.

Cabaniss, G. H.↗
NASA NTRS1980

Drilling side holes from a borehole

Machine takes long horizontal stratum samples from confines of 21 cm bore hole. Stacked interlocking half cylindrical shells mate to form rigid thrust tube. Drive shaft and core storage device is flexible and retractable. Entire machine fits in 10 meter length of steel tube. Machine could drill drainage or ventilation holes in coal mines, or provide important information for geological, oil, and geothermal surveys.

Collins, E. R., Jr.↗