Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BLADE TESTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1945

Blade Motion and Bouncing Tests of KD-1 Autogiro

There are forwarded herewith the results of blade motion and bouncing tests on the Kellett KD-1 three-bladed autogiro. Motion picture records and two-component accelerometer records were taken in flight during glides at air speeds from 30 miles per hour to 100 miles per hour indicator readings. Calibration curves of correct indicated air speed and rotor speed as functions of air speed meter reading were established with a trailing pitot-static head and a rotoscope, at 2,000 ft. altitude and an air density of 0.00231 slug/ cu. ft., all tests being made at approximately that density.

Wheatley, John B.↗
NASA NTRS1978

Wind tunnel tests of a blade subjected to midchord torsional oscillation at high subsonic stall flutter conditions

A mechanical drive system for oscillating blades in a wind tunnel at frequencies up to 767 hertz and amplitudes of + or - 1.2 deg is described. High-speed motion pictures of schlieren images of the flow over a double-circular arc blade oscillating in harmonic motion about the midchord revealed extensive shock patterns at a nominal free stream Mach number of 0.7, a mean angle of attack of 4 deg, and reduced frequency of about 0.7. A phase lag resulting from the slow response of the flow to the motion of the blade increased with increasing reduced frequency. This phase lag, based on the difference between the time the blade attained its maximum angle of attack and the time required for the normal shock to reach its extreme downstream position, was nominally 100 deg at the above conditions.

Boldman, D. R.↗
NASA NTRS1979

Design, fabrication and spin testing of ceramic blade metal disk attachment

A ceramic turbine blade-metal disk attachment was designed for small, non man-rated turbine engine applications. The selected design consisted of a hot pressed silicon nitride blade having a skewed dovetail attachment with a compliant interlayer between the disk and the blade. Two-dimensional and three-dimensional analyses predicted that life goals could be achieved, considering both NDE limitations and crack growth rates for the ceramic material. Twenty ceramic blades were fabricated to closely-held manufacturing tolerances. New fracture mechanics data at elevated temperature are presented.

Calvert, G.↗
NASA NTRS2002

A Subjective Test of Modulated Blade Spacing for Helicopter Main Rotors

Analytically, uneven (modulated) spacing of main rotor blades was found to reduce helicopter noise. A study was performed to see if these reductions transferred to improvements in subjective response. Using a predictive computer code, sounds produced by six main rotor configurations: 4 blades evenly spaced, 5 blades evenly spaced and four configurations with 5 blades with modulated spacing of varying amounts, were predicted. These predictions were converted to audible sounds corresponding to the level flyover, takeoff and approach flight conditions. Subjects who heard the simulations were asked to assess the overflight sounds in terms of noisiness on a scale of 0 to 10. In general the evenly spaced configurations were found less noisy than the modulated spacings, possibly because the uneven spacings produced a perceptible pulsating sound due to the very low fundamental frequency.

Sullivan, Brenda M.↗
NASA NTRS1985

Reflection plane tests of a wind turbine blade tip section with ailerons

Tests were conducted in the NASA Langley 30 by 60 foot Wind Tunnel on a full scale 7.31 m (24 ft) long tip section of a wind turbine rotor blade. The blade tip section was built with ailerons on the trailing edge. The ailerons, which spanned a length of 6.1 m (20 ft), were designed so that two types could be evaluated: the plain and the balanced. The ailerons were hinged on the suction surface at the 0.62 X chord station behind the leading edge. The purpose of the tests was to measure the aerodynamic characteristics of the blade section for: an angle of attack range from 0 deg to 90 deg aileron deflections from 0 deg to -90 deg, and Reynolds numbers of 0.79 and 1.5 x 10 to the 6th power. These data were then used to determine which aileron configuration had the most desirable rotor control and aerodynamic braking characteristics. Tests were also run to determine the effects of vortex generators, leading edge roughness, and the gaps between the aileron sections on the lift, drag, and chordwise force coefficients of the blade tip section.

Savino, J. M.↗
NASA NTRS1941

Wind-tunnel Tests of Eight-blade Single and Dual-rotating Propellers in the Tractor Position

Tests of 10-ft. diameter, eight-blade, single - and dual - rotating propellers were conducted in 20-ft propeller research tunnel. Propellers were mounted at front end of a streamline body in spinners that covered hubs and parts of shanks. Effect of a symmetrical wing mounted in slipstream was investigated. Blade-angle settings ranged from 20 Degrees to 65 Degrees. Results indicated that dual rotation resulted in gains of from 1 to 8 percent in efficiency over single rotation for eight-blade propellers, but presence of a wing reduced gain about one-half. Greater power absorption caused by dual rotation over flight range and higher efficiency or thrust for range of take-off and climb was indicated

PROPELLER-WING COMBINATIONS↗
NASA NTRS1993

Detailed measurements in the SSME high pressure fuel turbine with smooth rotor blades

Several tests of the Rocketdyne configuration of the Space Shuttle Main Engine (SSME) High Pressure Fuel Turbopump (HPFTP) Turbine have been completed in the Turbine Test Equipment (TTE) at Marshall Space Flight Center. The tests involved using scaled performance parameters and model measurements to predict the performance of the turbine. The overall performance has been the primary objective of the tests to date, but more detailed measurements are also of interest. During the most recent test of the Rocketdyne configuration of the HPFTP turbine with smooth rotor blades, several different measurement techniques were used to study the turbine inlet and exit velocity profiles, boundary layer thicknesses, turbulence intensities, etc. Data has been obtained using various hot film probes and three-hole cobra probes. Laser Velocimeter measurements were also made. The test plan and test data will be presented and discussed as well as lessons learned on how to obtain the various types of data.

Hudson, Susan T.↗
NASA NTRS1974

Cascade tests of serrated leading edge blading at high subsonic speeds

Cascade tests of two-dimensional fan rotor blade rows were performed to investigate the effects of leading edge serration on acoustic and aerodynamic performance. The test configurations covered a range of serration tooth geometries. Tests were performed to investigate effects of inlet air angle and velocity on performance. Aerodynamic performance was determined by flow surveys at the mid-span of the blade exit. Acoustic performance was determined by wake turbulence surveys and sound measurements in the semireverberent exhaust chamber. Measured acoustic and aerodynamic performance was comparable and indicated that a serration length of about six percent blade chord yields minimum noise generation and minimum total pressure losses.

Smith, E. G.↗
NASA NTRS1978

Transient dynamics of a flexible rotor with squeeze film dampers

A series of simulated blade loss tests are reported on a test rotor designed to operate above its second bending critical speed. A series of analyses were performed which predicted the transient behavior of the test rig for each of the blade loss tests. The scope of the program included the investigation of transient rotor dynamics of a flexible rotor system, similar to modern flexible jet engine rotors, both with and without squeeze film dampers. The results substantiate the effectiveness of squeeze film dampers and document the ability of available analytical methods to predict their effectiveness and behavior.

Buono, D. F.↗
DOE OSTI2014

CENER/NREL Collaboration in Testing Facility and Code Development: Cooperative Research and Development Final Report, CRADA Number CRD-06-207

Under the funds-in CRADA agreement, NREL and CENER will collaborate in the areas of blade and drivetrain testing facility development and code development. The project shall include NREL assisting in the review and instruction necessary to assist in commissioning the new CENER blade test and drivetrain test facilities. In addition, training will be provided by allowing CENER testing staff to observe testing and operating procedures at the NREL blade test and drivetrain test facilities. CENER and NREL will exchange blade and drivetrain facility and equipment design and performance information. The project shall also include exchanging expertise in code development and data to validate numerous computational codes.

17 WIND ENERGY↗
NASA NTRS1978

Flutter of Darrieus wind turbine blades

The testing of Darrieus wind turbines has indicated that under certain conditions, serious vibrations of the blades can occur, involving flatwise bending, torsion, and chordwise bending. A theoretical method of predicting the aeroelastic stability of the coupled bending and torsional motion of such blades with a view to determining the cause of these vibrations, and a means of suppressing them was developed.

Ham, N. D.↗
NASA NTRS2010

Development and Operation of an Automatic Rotor Trim Control System for use During the UH-60 Individual Blade Control Wind Tunnel Test

A full-scale wind tunnel test to evaluate the effects of Individual Blade Control (IBC) on the performance, vibration, noise and loads of a UH-60A rotor was recently completed in the National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Foot Wind Tunnel [1]. A key component of this wind tunnel test was an automatic rotor trim control system that allowed the rotor trim state to be set more precisely, quickly and repeatably than was possible with the rotor operator setting the trim condition manually. The trim control system was also able to maintain the desired trim condition through changes in IBC actuation both in open- and closed-loop IBC modes, and through long-period transients in wind tunnel flow. This ability of the trim control system to automatically set and maintain a steady rotor trim enabled the effects of different IBC inputs to be compared at common trim conditions and to perform these tests quickly without requiring the rotor operator to re-trim the rotor. The trim control system described in this paper was developed specifically for use during the IBC wind tunnel test

Theodore, Colin R.↗
NASA NTRS1945

Wind-Tunnel Tests of a Portion of a PV-2 Helicopter Rotor Blade

A portion of a PV-2 helicopter rotor blade has been tested in the 6- by 6-foot test section of the Langley stability tunnel to determine if the aerodynamic characteristics were seriously affected by cross flow or fabric distortion. The outer portion of the blade was tested as a reflection plane model pivoted about the tunnel wall to obtain various angles of cross flow over the blade. Because the tunnel wall acts as a plane of sy~try, the measured aerodynamic characteristics correspond to those of an airfoil having various angles of sweepforward and sweepback. Tests were made with the vents on the lower surface open and also with the vents sealed and the internal pressure held at -20 inches of water producing an internal pressure coefficient of -1.059. The change in contour resulting from the range of internal pressures used had very little effect on the aerodynamic characteristics of the blade. The test methods were considered to simulate inadequately the flow conditions over the rotor blade because the effects of cross flow were limited to conditions corresponding to sweep of the blade. The results indicated that this type of cross flow had only minor effects on the aerodynamic characteristics of the blade. It is believed, therefore, that future tests to determine the effects on the aerodynamic characteristics of cross flow should utilize complete rotors.

Kemp, William B., Jr.↗
DOE OSTI2021

Structural Testing Technology Development: Cooperative Research and Development Final Report, CRADA Number CRD-06-00200

NREL is the only organization in the US that is accredited to conduct tests of wind turbine systems and components in accordance with International Electrotechnical Commission (IEC) test standards. The National Wind Technology Center houses the only full-scale wind turbine blade drivetrain test facilities in the US. To maintain these facilities, accreditation, and the acceptance of the wind industry, NREL must strive continuously to maintain and improve staff capabilities, procedures, facility and equipment. In addition, as wind turbines continue to increase in size, NREL must improve its capability to test the larger components associated with these new turbines. NREL is currently investigating methods to increase blade and drivetrain testing capabilities. Mitsubishi Power Systems (MPS) must also strive to meet the demands of the evolving wind energy industry by developing, proving and manufacturing new, cost-effective blades for its turbines. Mitsubishi has established a joint venture with TPI composites of Rhode Island for manufacturing blades to be installed on US wind turbines. There is an obvious advantage to test these prototype blades in a US facility. The NREL blade test facility is uniquely capable of fulfilling this need. In addition, NREL can provide other testing support to MPS through the use of its dynamometer facility for drivetrain testing and through the use of NREL’s field-testing capabilities for testing wind turbine systems. This CRADA provides the opportunity for both organizations to achieve critical goals in development of wind energy in the US. MPS obtains verification of its wind turbine components and system. NREL obtains improved test capabilities.

17 WIND ENERGY↗