Results for “Attack surface analysis” — Page 6

NASA NTRS2021

A Computational Analysis of Boundary Layer Instability over the BOLT Configuration

The complex boundary layer flow over the BOLT flight configuration is known to exhibit multiple and potentially interacting instability mechanisms. This paper represents a continuation of our numerical investigation of the flow instabilities over the main test surface of the BOLT configuration by using state-of-the-art tools in multidimensional instability analysis. Specifically, the paper extends our previous computations by considering the separate effects of a nonzero angle-of-attack and a nonzero yaw on the modal instability characteristics of the boundary layer streaks adjacent to the minor-axis symmetry plane. At a selected condition from the ascent part of the anticipated flight trajectory, either type of departure from the design condition is shown to have a considerable impact on the structure of the laminar basic state and, hence, also on the amplification characteristics of the instability waves. A broader set of computations, including N-factor predictions for the relevant instabilities, will be presented in the final paper.

Boundary layer transition↗

NASA NTRS1958

Investigation of Control Effectiveness and Stability Characteristics of a Model of a Low-Wing Missile with Interdigitated Tail Surfaces at Mach Numbers of 2.29, 2.97, and 3.51

A brief investigation of the longitudinal stability and control effectiveness at supersonic speeds of a model of a low-wing missile with interdigitated tail surfaces was made in the Langley Unitary Plan wind tunnel. The data were obtained at Mach numbers M of 2.29, 2.97, and 3.51 for Reynolds number (based on the mean geometric chord of the wing) of 1.15 x 10(exp 6), 1.14 x 10(exp 6), and 1.11 x 10(exp 6), respectively. Data were obtained for three settings of the longitudinal control surfaces: with deflection of all surfaces, with deflection of the lower surfaces only, and with all surfaces undeflected. Directional stability data were obtained at M=3.51 for angles of attack of approximately 0 deg and 10 deg. These data, with summary data and typical schlieren photographs, are presented with only a brief analysis. The data indicate that the controls are effective throughout the Mach number range and lift-coefficient range (CL = -0.15 to 0.7, approximately) of the tests. There is a severe break in the pitching-moment curve at M=2.29 which might result in a pitch-up condition in flight, and also a large forward movement of the aerodynamic center with increasing Mach number that produces neutral longitudinal stability at M=3.51 for the moment center used in this investigation. The model was directionally unstable at M=3.51; however, the level of directional stability was about the same for 0 deg and 10 deg angles of attack.

STABILITY AND CONTROL↗

NASA NTRS2000

An Entry Flight Controls Analysis for a Reusable Launch Vehicle

The NASA Langley Research Center has been performing studies to address the feasibility of various single-stage to orbit concepts for use by NASA and the commercial launch industry to provide a lower cost access to space. Some work on the conceptual design of a typical lifting body concept vehicle, designated VentureStar(sup TM) has been conducted in cooperation with the Lockheed Martin Skunk Works. This paper will address the results of a preliminary flight controls assessment of this vehicle concept during the atmospheric entry phase of flight. The work includes control analysis from hypersonic flight at the atmospheric entry through supersonic speeds to final approach and landing at subsonic conditions. The requirements of the flight control effectors are determined over the full range of entry vehicle Mach number conditions. The analysis was performed for a typical maximum crossrange entry trajectory utilizing angle of attack to limit entry heating and providing for energy management, and bank angle to modulation of the lift vector to provide downrange and crossrange capability to fly the vehicle to a specified landing site. Sensitivity of the vehicle open and closed loop characteristics to CG location, control surface mixing strategy and wind gusts are included in the results. An alternative control surface mixing strategy utilizing a reverse aileron technique demonstrated a significant reduction in RCS torque and fuel required to perform bank maneuvers during entry. The results of the control analysis revealed challenges for an early vehicle configuration in the areas of hypersonic pitch trim and subsonic longitudinal controllability.

Calhoun, Philip↗

NASA NTRS1959

Analysis and Evaluation of Supersonic Underwing Heat Addition

The linearized theory for heat addition under a wing has been developed to optimize wing geometry, heat addition, and angle of attack. The optimum wing has all of the thickness on the underside of the airfoil, with maximum-thickness point well downstream, has a moderate thickness ratio, and operates at an optimum angle of attack. The heat addition is confined between the fore Mach waves from under the trailing surface of the wing. By linearized theory, a wing at optimum angle of attack may have a range efficiency about twice that of a wing at zero angle of attack. More rigorous calculations using the method of characteristics for particular flow models were made for heating under a flat-plate wing and for several wings with thickness, both with heat additions concentrated near the wing. The more rigorous calculations yield in practical cases efficiencies about half those estimated by linear theory. An analysis indicates that distributing the heat addition between the fore waves from the undertrailing portion of the wing is a way of improving the performance, and further calculations appear desirable. A comparison of the conventional ramjet-plus wing with underwing heat addition when the heat addition is concentrated near the wing shows the ramjet to be superior on a range basis up to Mach number of about B. The heat distribution under the wing and the assumed ramjet and airframe performance may have a marked effect on this conclusion. Underwing heat addition can be useful in providing high-altitude maneuver capability at high flight Mach numbers for an airplane powered by conventional ramjets during cruise.

wings↗

NASA NTRS1999

Engineering Overview of a Multidisciplinary HSCT Design Framework Using Medium-Fidelity Analysis Codes

An objective of the HPCC Program at NASA Langley has been to promote the use of advanced computing techniques to more rapidly solve the problem of multidisciplinary optimization of a supersonic transport configuration. As a result, a software system has been designed and is being implemented to integrate a set of existing discipline analysis codes, some of them CPU-intensive, into a distributed computational framework for the design of a High Speed Civil Transport (HSCT) configuration. The proposed paper will describe the engineering aspects of integrating these analysis codes and additional interface codes into an automated design system. The objective of the design problem is to optimize the aircraft weight for given mission conditions, range, and payload requirements, subject to aerodynamic, structural, and performance constraints. The design variables include both thicknesses of structural elements and geometric parameters that define the external aircraft shape. An optimization model has been adopted that uses the multidisciplinary analysis results and the derivatives of the solution with respect to the design variables to formulate a linearized model that provides input to the CONMIN optimization code, which outputs new values for the design variables. The analysis process begins by deriving the updated geometries and grids from the baseline geometries and grids using the new values for the design variables. This free-form deformation approach provides internal FEM (finite element method) grids that are consistent with aerodynamic surface grids. The next step involves using the derived FEM and section properties in a weights process to calculate detailed weights and the center of gravity location for specified flight conditions. The weights process computes the as-built weight, weight distribution, and weight sensitivities for given aircraft configurations at various mass cases. Currently, two mass cases are considered: cruise and gross take-off weight (GTOW). Weights information is obtained from correlations of data from three sources: 1) as-built initial structural and non-structural weights from an existing database, 2) theoretical FEM structural weights and sensitivities from Genesis, and 3) empirical as-built weight increments, non-structural weights, and weight sensitivities from FLOPS. For the aeroelastic analysis, a variable-fidelity aerodynamic analysis has been adopted. This approach uses infrequent CPU-intensive non-linear CFD to calculate a non-linear correction relative to a linear aero calculation for the same aerodynamic surface at an angle of attack that results in the same configuration lift. For efficiency, this nonlinear correction is applied after each subsequent linear aero solution during the iterations between the aerodynamic and structural analyses. Convergence is achieved when the vehicle shape being used for the aerodynamic calculations is consistent with the structural deformations caused by the aerodynamic loads. To make the structural analyses more efficient, a linearized structural deformation model has been adopted, in which a single stiffness matrix can be used to solve for the deformations under all the load conditions. Using the converged aerodynamic loads, a final set of structural analyses are performed to determine the stress distributions and the buckling conditions for constraint calculation. Performance constraints are obtained by running FLOPS using drag polars that are computed using results from non-linear corrections to the linear aero code plus several codes to provide drag increments due to skin friction, wave drag, and other miscellaneous drag contributions. The status of the integration effort will be presented in the proposed paper, and results will be provided that illustrate the degree of accuracy in the linearizations that have been employed.

Weston, R. P.↗

NASA NTRS1946

Wind-Tunnel Investigation of the Horizontal Motion of a Wing Near the Ground

By the method of images the horizontal steady motion of a wing at small heights above the ground was investigated in the wind tunnel, A rectangular wing with Clark Y-H profile was tested with and without flaps. The distance from the trailing edge of the wing to the ground was varied within the limits 0.75 less than or = s/c less than or = 0.25. Measurements were made of the lift, the drag, the pitching moment, and the pressure distribution at one section. For a wing without flaps and one with flaps a considereble decrease in the lift force and a,drop in the drag was obtained at angles of attack below stalling. The flow separation near the ground occurs at smaller angles of attack than is the case for a great height above the ground. At horizontal steady flight for practical values of the height above the ground the maximum lift coefficient for the wing without flaps changes little, but markedly decreases for the wing with flaps. Analysis of these phenomena involves the investigation of the pressure distribution. The pressure distribution curves showed that the changes occurring near the ground are not equivalent to a change in the angle of attack. At the lower surface of the section a very strong increase in the pressures is observed. The pressure changes on the upper surface at angles of attack below stalling are insignificant and lead mainly to an increase in the unfavorable pressure gradient, resulting in the earlier occurrence of separation. For a wing with flaps at large angles of attack for distances from the trailing edge of the flap to the ground less than 0.5 chord, the flow between the wing end the ground is retarded so greatly that the pressure coefficient at the lower surface of the section is very near its limiting value (P = 1), and any further possibility of increase in the pressure is very small. In the application an approximate computation procedure is given of the change of certain aerodynamic characteristics for horizontal steady flight near the ground.

Serebrisky, Y. M.↗

NASA NTRS1972

Space shuttle orbiter reentry flow field and heating analysis

The reentry flow field and thermal environment around the straight wing shuttle orbiter vehicle were determined. Both rarefied and continuum flow fields and associated heating rates on various configurations representative of the orbiter at high angle of attack were calculated. Rarefied flow fields and heating rates were computed by the Monte Carlo direct simulation technique for altitudes above 82.3 km. Continuum inviscid flow fields were calculated by 2-D unsteady and 3-D steady finite difference/artificial viscosity methods and also by a 2-D shock layer analysis technique. Viscous flow fields and heating rates in the continuum regime were computed by a boundary layer integral matrix method for laminar flow and by an aerodynamic surface heating technique for turbulent flow. Shapes considered in the study included flat plates (representing the underside of the orbiter fuselage or the wing MAC), orbiter fuselage cross sections, orbiter wing airfoils, and 3-D orbiter configurations, all at high angle of attack (40 - 60 deg). The theoretical results showed good agreement with measured pressure and heat transfer data.

Rochelle, W. C.↗

NASA NTRS2009

Better Spectrometers, Beautiful Spectra and Confusion for All

The confluence of enormous improvements in submillimeter receivers and the development of powerful large scale observatories is about to force astrophysics and the sciences that support it to develop novel approaches for interpretation of data. The historical method of observing one or two lines and carefully analyzing them in the context of a simple model is now only applicable for distant objects where only a few lines are strong enough to be observable. Modern observatories collect many GHz of high signal-to-noise spectra in a single observation and in many cases, at sufficiently high spatial resolution to start resolving chemically distinct regions. The observatories planned for the near future and the inevitable upgrades of existing facilities will make large spectral data sets the rule rather than the exception in many areas of molecular astrophysics. The methodology and organization required to fully extract the available information and interpret these beautiful spectra represents a challenge to submillimeter astrophysics similar in magnitude to the last few decades of effort in improving receivers. The quality and abundance of spectra effectively prevents line-by-line analysis from being a time efficient proposition, however, global analysis of complex spectra is a science in its infancy. Spectroscopy at several other wavelengths have developed a number of techniques to analyze complex spectra, which can provide a great deal of guidance to the molecular astrophysics community on how to attack the complex spectrum problem. Ultimately, the challenge is one of organization, similar to building observatories, requiring teams of specialists combining their knowledge of dynamical, structural, chemical and radiative models with detailed knowledge in molecular physics and gas and grain surface chemistry to extract and exploit the enormous information content of complex spectra. This paper presents a spectroscopists view of the necessary elements in a tool for complex spectral analysis.

Spectral Analysis↗

NASA NTRSDate not supplied

Pterodactyl: Guidance and Control of a Symmetric Deployable Entry Vehicle using an Aerodynamic Control System

The NASA-funded Pterodactyl project seeks to advance the current state-of-the-art for entry vehicles by developing novel guidance and control technologies for Deployable Entry Vehicles (DEVs). This paper presents the guidance and control design and analysis for a mechanically-deployed DEV with a symmetric aeroshell and aerodynamic control surfaces. We present guidance tuning using both bank angle modulation with the Fully-Numerical Predictor Corrector Entry Guidance technique (FNPEG) and angle of attack and sideslip modulation with FNPEG with uncoupled range control (FNPEG URC). We show the control system design and simulation results for tracking both types of guidance commands.

Benjamin W L Margolis↗

NASA NTRS2021

Pterodactyl: Guidance and Control of a Symmetric Deployable Entry Vehicle using an Aerodynamic Control System

The NASA-funded Pterodactyl project seeks to advance the current state-of-the-art for entry vehicles by developing novel guidance and control technologies for Deployable Entry Vehicles (DEVs). This paper presents the guidance and control design and analysis for a mechanically-deployed DEV with a symmetric aeroshell and aerodynamic control surfaces. We present guidance tuning using both bank angle modulation with the Fully-Numerical Predictor Corrector Entry Guidance technique (FNPEG) and angle of attack and sideslip modulation with FNPEG with uncoupled range control (FNPEG URC). We show the control system design and simulation results for tracking both types of guidance commands.

Benjamin Margolis↗

NASA NTRS1975

Wind tunnel investigation of aerodynamic loads on a large-scale externally blown flap model and comparison with theory

Results from a wind-tunnel investigation of a large-scale externally blown flap model are presented. The model was equipped with four turbofan engines, a triple-slotted flap system, and a T-tail. The wing had a quarter-chord sweep of 25 deg, an aspect ratio of 7.28, and a taper ratio of 0.4. Aerodynamic loads and load distributions were determined from a total of 564 static pressure orifices located on the upper and lower surfaces of the slat, wing, and flaps. Loads are presented for variations of angle of attack, engine thrust setting, and flap deflection angle. In addition, the experimental results are compared with analytical results calculated by using a potential flow analysis.

Perry, B., III↗

NASA NTRS1998

Design and Performance Calculations of a Propeller for Very High Altitude Flight

Reported here is a design study of a propeller for a vehicle capable of subsonic flight in Earth's stratosphere. All propellers presented were required to absorb 63.4 kW (85 hp) at 25.9 km (85,000 ft) while aircraft cruise velocity was maintained at Mach 0.40. To produce the final design, classic momentum and blade-element theories were combined with two and three-dimensional results from the Advanced Ducted Propfan Analysis Code (ADPAC), a numerical Navier-Stokes analysis code. The Eppler 387 airfoil was used for each of the constant section propeller designs compared. Experimental data from the Langley Low-Turbulence Pressure Tunnel was used in the strip theory design and analysis programs written. The experimental data was also used to validate ADPAC at a Reynolds numbers of 60,000 and a Mach number of 0.20. Experimental and calculated surface pressure coefficients are compared for a range of angles of attack. Since low Reynolds number transonic experimental data was unavailable, ADPAC was used to generate two-dimensional section performance predictions for Reynolds numbers of 60,000 and 100,000 and Mach numbers ranging from 0.45 to 0.75. Surface pressure coefficients are presented for selected angles of attack. in addition to the variation of lift and drag coefficients at each flow condition. A three-dimensional model of the final design was made which ADPAC used to calculated propeller performance. ADPAC performance predictions were compared with strip-theory calculations at design point. Propeller efficiency predicted by ADPAC was within 1.5% of that calculated by strip theory methods, although ADPAC predictions of thrust, power, and torque coefficients were approximately 5% lower than the strip theory results. Simplifying assumptions made in the strip theory account for the differences seen.

Koch, L. Danielle↗

NASA NTRSDate not supplied

Implementation of an Unsteady PSP System in the NASA Transonic Dynamics Tunnel

An unsteady pressure-sensitive paint (uPSP) system has been developed to provide time-resolved pressure measurements in the NASA Langley Transonic Dynamics Tunnel (TDT). Obtaining these measurements necessitated the development of environmental enclosures to protect the high-speed camera and ultraviolet lights required for uPSP from the harsh environment present during tunnel operation. Since the facility main drive was non-functioning during the testing window, performance of the uPSP system was demonstrated using an impinging jet with a passive oscillator attachment to provide unsteady flow with a known frequency independent of amplitude. Measurements were obtained for tunnel pressures ranging from 565 to 2116 psf, and model angles of attack between -4 degrees and 4 degrees. Results indicate that the system is capable of measuring surface pressure differentials on the order of 0.01 psi at full scale with a camera frame rate of at least 10 kHz. Spectral analysis shows that the fundamental frequency of the oscillating jet is captured by the uPSP system, as are the second and third harmonics. Dynamic mode decomposition highlights the dominant coherent spatial structures of the surface pressure, along with the associated frequency and growth rate of each mode, allowing for a de-noised reconstruction of the uPSP measurements. The experimental campaign outlined within this report also confirmed compatibility of the uPSP system with the TDT facility data acquisition system, and verified the successful integration with existing processing capabilities within the NASA advanced supercomputing environment.

unsteady pressure-sensitive paint↗

NASA NTRSDate not supplied

Implementation of an Unsteady PSP System in the NASA Transonic Dynamics Tunnel

An unsteady pressure-sensitive paint (uPSP) system has been developed to provide time-resolved pressure measurements in the NASA Langley Transonic Dynamics Tunnel (TDT). Obtaining these measurements necessitated the development of environmental enclosures to protect the high-speed camera and ultraviolet lights required for uPSP from the harsh environment present during tunnel operation. Since the facility main drive was non-functioning during the testing window, performance of the uPSP system was demonstrated using an impinging jet with a passive oscillator attachment to provide unsteady flow with a known frequency independent of amplitude. Measurements were obtained for tunnel pressures ranging from 565 to 2116 psf, and model angles of attack between -4 degrees and 4 degrees. Results indicate that the system is capable of measuring surface pressure differentials on the order of 0.01 psi at full scale with a camera frame rate of at least 10 kHz. Spectral analysis shows that the fundamental frequency of the oscillating jet is captured by the uPSP system, as are the second and third harmonics. Dynamic mode decomposition highlights the dominant coherent spatial structures of the surface pressure, along with the associated frequency and growth rate of each mode, allowing for a de-noised reconstruction of the uPSP measurements. The experimental campaign outlined within this report also confirmed compatibility of the uPSP system with the TDT facility data acquisition system, and verified the successful integration with existing processing capabilities within the NASA advanced supercomputing environment.

unsteady pressure-sensitive paint↗

NASA NTRSDate not supplied

Implementation of an Unsteady PSP System in the NASA TDT

An unsteady pressure-sensitive paint (uPSP) system has been developed to provide time-resolved pressure measurements in the NASA Langley Transonic Dynamics Tunnel (TDT). Obtaining these measurements necessitated the development of environmental enclosures to protect the high-speed camera and ultraviolet lights required for uPSP from the harsh environment present during tunnel operation. Since the facility main drive was non-functioning during the testing window, performance of the uPSP system was demonstrated using an impinging jet with a passive oscillator attachment to provide unsteady flow with a known frequency independent of amplitude. Measurements were obtained for tunnel pressures ranging from 565 to 2116 psf, and model angles of attack between -4 degrees and 4 degrees. Results indicate that the system is capable of measuring surface pressure differentials on the order of 0.01 psi at full scale with a camera frame rate of at least 10 kHz. Spectral analysis shows that the fundamental frequency of the oscillating jet is captured by the uPSP system, as are the second and third harmonics. Dynamic mode decomposition highlights the dominant coherent spatial structures of the surface pressure, along with the associated frequency and growth rate of each mode, allowing for a de-noised reconstruction of the uPSP measurements. The experimental campaign outlined within this report also confirmed compatibility of the uPSP system with the TDT facility data acquisition system, and verified the successful integration with existing processing capabilities within the NASA advanced supercomputing environment. Note: this presentation is an MP4 video with sound, color with a run time of 10 minutes 37 seconds.

unsteady pressure-sensitive paint↗

DOE OSTI2024

Criticality Analysis of Wind Turbine Components - Intern Poster [Poster]

Wind turbines are an important part of critical energy infrastructure, with wind farms generating more than 10% of US energy in 2023. The goal of this project is to identify and analyze major, common components of wind turbines to reach a preliminary understanding of which should be considered most critical in terms of turbine operation and attack surface. At the time of this project, minimal data was available regarding component costs and lead times, so a qualitative risk assessment approach was used. Components were given a score of 1-5 in four categories– cost to repair, operational downtime, ease of physical attack, and ease of cyber attack. An overall component criticality score was assigned based on the sum of those scores, with a higher score indicating higher criticality. The turbine control system was identified as the most critical component, closely followed by the blades, structural components, and gearbox. This is ongoing project, and further research on the supply chain for wind turbine components will allow for a deeper and more concrete understanding of component criticality.

17 WIND ENERGY↗

DOE OSTI2024

Convergent ab initio analysis of the multi-channel HOBr + H reaction

High-level potential energy surfaces for three reactions of hypobromous acid with atomic hydrogen were computed at the CCSDTQ/CBS//CCSDT(Q)/complete basis set level of theory. Focal point analysis was utilized to extrapolate energies and gradients for energetics and optimizations, respectively. The H attack at Br and subsequent Br–O cleavage were found to proceed barrierlessly. The slightly submerged transition state lies −0.2 kcal mol−1 lower in energy than the reactants and produces OH and HBr. The two other studied reaction paths are the radical substitution to produce H2O and Br with a 4.0 kcal mol−1 barrier and the abstraction at hydrogen to produce BrO and H2 with an 11.2 kcal mol−1 barrier. The final product energies lie −37.2, −67.9, and −7.3 kcal mol−1 lower in energy than reactants, HOBr + H, for the sets of products OH + HBr, H2O + Br, and H2 + BrO, respectively. Additive corrections computed for the final energetics, particularly the zero-point vibrational energies and spin–orbit corrections, significantly impacted the final stationary point energies, with corrections up to 6.2 kcal mol−1.

Chemistry↗

DOE OSTI2024

Attack Surface of Wind Energy Technologies in the United States

Low cost, reliable electrical energy production from wind relies upon automation and control systems, arguably more so than traditional thermal generation. These same systems, however, can serve as the target of adversaries’ cyber-attacks. Idaho National Laboratory (INL), at the request of the Department of Energy’s (DOE’s) Office of Cybersecurity, Energy Security, and Emergency Response (CESER) and Energy Efficiency and Renewable Energy’s (EERE’s) Wind Energy Technologies Office (WETO), evaluated a generalized wind plant architecture to understand the classes of potential threat actors and the vectors that could enable a cyber-attack. This evaluation explores the attack surface of a representative wind plant, identifying potential methods and vectors that an adversary could leverage to conduct a cyber-attack. Included in this assessment are some recommended mitigations and approaches. Each recommendation requires a full security evaluation, cost/benefit analysis, and risk analysis by each owner and operator.

17 WIND ENERGY↗