Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Acoustic Liners”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Optimization of acoustic liners by the hybrid finite element-integral approach

An iterative solution technique for predicting the sound field radiated from a turbofan inlet is used to predict the optimum inlet acoustic liner. The analytical approach divides the sound field into two regions: the sound field within and near the inlet which is computed using the finite element method and the radiation field beyond the inlet which is calculated using an integral solution technique. A continuous solution is obtained by matching the finite element and integral solutions at the interface between the two regions. Using a trial and error scheme, this analytical procedure is used to calculate the impedance value of the duct liner which will produce a minimum sound pressure level in the far field. Several examples of straight and non-uniform ducts with and without flow are presented.

Sigman, R. K.↗
NASA NTRS2020

Evaluation of Packing_3D Code for Design of Variable-Depth, Bent-Chamber Acoustic Liners

Increases in the bypass ratio for commercial aircraft engines have caused the broadband fan noise component to become dominant. As a result, there is a need to develop improved acoustic liners suitable for absorption of this fan noise over a wide frequency range, preferably up to at least two octaves. Variable depth liners with bent chambers and three-dimensional geometries present one way to achieve this goal, however, they can be difficult and time-consuming to design due to their complexity and volume constraints. A packing code, called Packing3D, has been developed that automatically designs the chamber configurations of such liners once the chamber dimensions and volume constraints are known. The code uses a randomized trial and error approach to place each chamber in a representation of the liner sample, then returns a colored diagram and sufficient information for the liner sample to be fabricated. For evaluation, the code is used to design four liner samples of varying levels of complexity. These samples are tested with and without a mesh facesheet in the NASA Langley Normal Incidence Tube, and the results are compared to predictions computed in COMSOL. The results indicate that the packing code is able to quickly design samples that are predictable, achieve the desired absorption spectrum, fit the given constraints, and are able to be built. This code is flexible, lends itself to optimization, and allows samples to be designed quickly, accurately, and efficiently.

Marinova, Miroslava M.↗
NASA NTRS1975

Optimum segmented acoustic liners for flow ducts

Analytical and experimental investigations of phased linings for a duct containing a uniform mean flow were conducted as part of a program concerned with the design of more efficient acoustic liners for the reduction of noise emission. An analytical technique was developed which predicts the propagation of sound waves in flow ducts with segmented liners. The calculations for implementing the derived algorithms were conducted with the aid of FORTRAN IV computer programs. Attention is also given to details regarding the experimental program which was designed to supplement the theoretical studies.

Sawdy, D. T.↗
NASA NTRS2000

Flow Duct Data for Validation of Acoustic Liner Codes for Impedance Eduction

The objective of the study reported here was to acquire acoustic and flow data with hard and lined duct wall duct sections for validation of a liner prediction code being developed at NASA LaRC. Both the mean flowfield and acoustic flowfields were determined in a cross-plane of the rectangular duct. A flow duct facility with acoustic drivers connected to a rectangular (4.7 x 2.0 inch) source section and a linear acoustic liner mounted downstream of the source section was used in this study. The liner section was designed to allow liner materials to be placed on all 4 walls of the duct. The test liner was of the locally-reacting type and was made from a ceramic material. The material, consisting of a tubular structure, was provided by NASA LaRC. The liner was approximately 8.89 cm (3.5 inches) thick. For the current study, only the two "short" sides of the duct were lined with liner material. The other two sides were hard walls. Two especially built instrumentation sections were attached on either sides of the liner section to allow acoustic and flow measurements to be made upstream and downstream of the liner. The two instrumentation duct sections were built to allow measurement of acoustic and flow properties at planes perpendicular to flow upstream and downstream of the liner section. The instrumentation section was also designed to provide a streamwise gradient in acoustic (complex) pressure from which the acoustic particle velocity, needed for the model validation, can be computed. Flow measurements included pressure, temperature, and velocity profiles upstream of the liner section. The in-flow sound pressure levels and phases were obtained with a microphone probe equipped with a nose cone in two cross planes upstream of the liner and two cross plane downstream of the liner. In addition to the acoustic measurements at the cross planes. axial centerline acoustic data was acquired using an axially traversing microphone probe which was traversed from a location upstream of the liner to some distance downstream of the liner. All probes used here had to be calibrated with respect to a standard microphone equipped with a nose cone to allow for the effects of flow.

Ahuja, K. K.↗
NASA NTRS2016

Compact, Lightweight, Ceramic Matrix Composite (CMC) Based Acoustic Liners for Reducing Subsonic Jet Aircraft Engine Noise

Recent developments have reduced fan and jet noise contributions to overall subsonic aircraft jet-engine noise. Now, aircraft designers are turning their attention toward reducing engine core noise. The NASA Glenn Research Center and NASA Langley Research Center have teamed to investigate the development of a compact, lightweight acoustic liner based on oxide/oxide ceramic matrix composite (CMC) materials. The NASA team has built upon an existing oxide/oxide CMC sandwich structure concept that provides monotonal noise reduction. Oxide/oxide composites have good high temperature strength and oxidation resistance, which could allow them to perform as core liners at temperatures up to 1000C (1832F), and even higher depending on the selection of the composite constituents. NASA has initiated the evaluation of CMC-based liners that use cells of different lengths (variable-depth channels) or effective lengths to achieve broadband noise reduction. Reducing the overall liner thickness is also a major goal, to minimize the volume occupied by the liner. As a first step toward demonstrating the feasibility of our concepts, an oxide/oxide CMC acoustic testing article with different channel lengths was tested. Our approach, summary of test results, current status, and goals for the future are reported.

testing↗
NASA NTRS1975

Suppression of nonlinear oscillations in combustors with partial length acoustic liners

An analytical model is formulated for a three-dimensional nonlinear stability problem in a rocket motor combustion chamber. The chamber is modeled as a right circular cylinder with a short (multi-orifice) nozzle, and an acoustic linear covering an arbitrary portion of the cylindrical periphery. The combustion is concentrated at the injector and the gas flow field is characterized by a mean Mach number. The unsteady combustion processes are formulated using the Crocco time lag model. The resulting equations are solved using a Green's function method combined with numerical evaluation techniques. The influence of acoustic liners on the nonlinear waveforms is predicted. Nonlinear stability limits and regions where triggering is possible are also predicted for both lined and unlined combustors in terms of the combustion parameters.

Espander, W. R.↗
NASA NTRS2017

Diagnostic Techniques to Elucidate the Aerodynamic Performance of Acoustic Liners

In support of Topic A.2.8 of NASA NRA NNH10ZEA001N, the University of Florida (UF) has investigated the use of flow field optical diagnostic and micromachined sensor-based techniques for assessing the wall shear stress on an acoustic liner. Stereoscopic particle image velocimetry (sPIV) was used to study the velocity field over a liner in the Grazing Flow Impedance Duct (GFID). The results indicate that the use of a control volume based method to determine the wall shear stress is prone to significant error. The skin friction over the liner as measured using velocity curve fitting techniques was shown to be locally reduced behind an orifice, relative to the hard wall case in a streamwise plane centered on the orifice. The capacitive wall shear stress sensor exhibited a linear response for a range of shear stresses over a hard wall. PIV over the liner is consistent with lifting of the near wall turbulent structure as it passes over an orifice, followed by a region of low wall shear stress.

June, Jason↗
NASA NTRS2019

Initial Developments of a Low Drag Variable Depth Acoustic Liner

The purpose of this study is to assess the acoustic performance and relative drag of a new type of variable depth liner containing pairs of resonators coupled together by shared inlet volumes just below the facesheet. This type of liner has the potential to achieve a targeted impedance with fewer openings in the facesheet, and therefore less drag, than previous designs. To better understand the limitations of the concept, three sets of samples were designed and tested in the NASA Langley normal incidence and grazing flow impedance tubes. Each set of samples consisted of a baseline variable depth liner with straight chambers, and a prototype liner with shared inlet volumes. Measurements conducted in both the normal incidence and grazing flow impedance tubes confirm that the prototype liner can achieve the same impedance as the baseline variable depth liner at discrete frequencies with 50% less open area. This results in a 75% reduction in the drag penalty relative to the baseline design. The proposed concept is not, however, able to achieve a flat, broadband impedance as effectively as the baseline liner. So, while the proposed concept is well suited for multitonal design metrics, tradeoffs must be made between liner drag and acoustic performance when broadband attenuation is required.

Schiller, Noah H.↗
NASA NTRS1985

A method for determining acoustic-liner admittance in ducts with sheared flow in two-cross-sectional directions

A method is developed for determining the acoustic admittance of a test liner installed in the wall of a grazing flow impedance tube. The mean flow is permitted flow gradients in both cross-sectional directions of the tube. The unknown admittance value is obtained by solving an eigenvalue problem. This eigenvalue problem results from the application of the finite-element method to the partial differential equation and boundary conditions governing the acoustic field. The credibility of the method is established by comparing results with exact solutions obtained for a constant mean-flow profile and with previous results for cases involving shear in only one cross-sectional direction. Excellent comparisons are obtained in both cases. The analysis is used in conjunction with a limited amount of experimental data and shows that the flow must be accurately modeled in order to determine the acoustic-liner properties.

Watson, W. R.↗
NASA NTRSDate not supplied

Time Domain Approach for Acoustic Liner Analysis

- Procedures for implementing the Ingard-Myers impedance condition in time domain - Instability issue of the Ingard-Myers Condition - Proposed stabilization of the Ingard-Myers condition - Numerical examples

time domain impedance boundary condition↗
NASA NTRS2010

Effects of Flow Profile on Educed Acoustic Liner Impedance

This paper presents results of an investigation of the effects of shear flow profile on impedance eduction processes employed at NASA Langley. Uniform and 1-D shear-flow propagation models are used to educe the acoustic impedance of three test liners based on aeroacoustic data acquired in the Langley Grazing Flow Impedance Tube, at source levels of 130, 140 and 150 dB, and at centerline Mach numbers of 0.0, 0.3 and 0.5. A ceramic tubular, calibration liner is used to evaluate the propagation models, as this liner is expected to be insensitive to SPL, grazing flow Mach number, and flow profile effects. The propagation models are then used to investigate the effects of shear flow profile on acoustic impedances educed for two conventional perforate-over-honeycomb liners. Results achieved with the uniform-flow models follow expected trends, but those educed with the 1-D shear-flow model do not, even for the calibration liner. However, when the flow profile used with the shear-flow model is varied to increase the Mach number gradient near the wall, results computed with the shear-flow model are well matched to those achieved with the uniform-flow model. This indicates the effects of flow profile on educed acoustic liner impedance are small, but more detailed investigations of the flow field throughout the duct are needed to better understand these effects.

Jones, Michael G.↗
NASA NTRS2023

Partition Thickness Considerations for Additively Manufactured Acoustic Liners

Three types of uniform-depth liners are evaluated to explore the effects of partition thickness on the surface impedance achieved with additively manufactured liners. A transmission line code is used to predict the effects of sound transmission through empty chambers and wire mesh facesheets, and is combined with the Motsinger and Kraft model to account for sound transmission through perforated facesheets. The inclusion of partitions causes a blockage effect, i.e., a portion of the surface is ‘blocked’ (nonactive surface). For liners with no facesheet, these blockage effects are incorporated simply by accounting for the change in cross sectional area between the individual chamber and the unit cell that includes half of a partition thickness around the perimeter of this chamber. Comparison of impedances predicted in this manner with data acquired in the NASA Langley Normal Incidence Tube (NIT) confirms the efficacy of this modeling approach. Two approaches are considered to account for the inclusion of a wiremesh or perforated plate facesheet on these same cores. The first accounts for the effects of partition thickness before including the transfer impedance across the facesheet, while the second reverses these steps. A comparison of data acquired in the NASA NIT with modeled impedances suggests the first approach is best when the facesheet is a wire mesh, but the second approach is preferred when a perforated plate facesheet is used. It is hypothesized that this is due to the fact that a lumped element model is used to compute the transfer impedance across a wire mesh, while the corresponding transfer impedance across a perforated sheet explicitly incorporates the efffects of the liner core. However, comparisons of data acquired in the NASA Langley Grazing Flow Impedance Tube with modeled impedances seem slightly better when the first approach is employed with a perforated plate facesheet. Thus, the effects of partition thickness on liners with perforated sheets subjected to grazing incidence sound require further review

acoustic↗
NASA NTRS2007

Electromechanical acoustic liner

A multi-resonator-based system responsive to acoustic waves includes at least two resonators, each including a bottom plate, side walls secured to the bottom plate, and a top plate disposed on top of the side walls. The top plate includes an orifice so that a portion of an incident acoustical wave compresses gas in the resonators. The bottom plate or the side walls include at least one compliant portion. A reciprocal electromechanical transducer coupled to the compliant portion of each of the resonators forms a first and second transducer/compliant composite. An electrical network is disposed between the reciprocal electromechanical transducer of the first and second resonator.

Sheplak, Mark↗