Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ATF”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Mechanical and chemical properties of PVD and cold spray Cr-coatings on Zircaloy-4

In this paper, accident-tolerant fuel (ATF) cladding materials aim to improve fuel reliability and safety during accident scenarios in water-cooled reactors. These ATF cladding should also perform comparable or better than the current zirconium alloy cladding under reactor normal operating conditions. Surface-modified Zircaloy-4 was produced by depositing a protective coating of chromium by two different coating techniques, Physical Vapor Deposition (PVD) and Cold Spray (CS). The coating thickness, structure, composition, and mechanical properties of the coated Zircaloy were assessed with advanced materials characterization techniques. Results showed a strengthening effect of the Cr-coating, along with ~83% higher hardness compared to that of the Zircaloy-4 substrate. Surface topography and surface chemistry of the Cr-coated Zircaloy-4 were assessed with contact profilometry, atomic force microscopy, contact angle goniometry, and X-ray photoelectron spectroscopy. Deposited Cr-coating significantly improved surface wettability compared to the substrate Zircaloy-4. The formation of surface oxides on the coatings by prolonged exposure to ambient air showed a further increase in the hydrophobic behavior. Surface parameters and surface chemistry after flow boiling critical heat flux tests, conducted at atmospheric pressure, evidenced a slight increase in surface roughness with notable changes in wettability associated with the formation of surface oxides.

36 MATERIALS SCIENCE↗
DOE OSTI2020

$\mathrm{UPDATED}$ $\mathrm{U3SI2}$ thermal creep model and sensitivity analysis of the $\mathrm{U3SI2-SIC}$ accident tolerant $\mathrm{FUEL}$

U 3 Si 2 is a candidate accident tolerant fuel (ATF) replacement for UO 2 . U 3 Si 2 ’s high uranium density and high thermal conductivity are favorable properties in steady-state and accident conditions. Low power performance of this U3Si2-SiC concept fuel is compared to that of UO 2 -Zr4 fuels by implementing models that describe the properties of U 3 Si 2 and SiC-SiC into Idaho National Laboratory's (INL) fuel performance code, BISON. Included in these material models is a thermal creep model for U 3 Si 2 based on compressive creep data. The simulated results are in keeping with community knowledge that the U 3 Si 2 -SiC concept fuel may serve as a replacement for UO 2 -Zr4 fuels during steady-state operation, provided the mSiC layer remains under compression. Through a moderate power history and three 24-month fuel cycles, the mSiC layer remains under compressive stress through a burnup of 80 MWd/kgU. During low power operation, failure of the mSiC layer generally occurs prior to significant thermal creep in U 3 Si 2 . Generally, U 3 Si 2 creep is temperature sensitive and of little importance at the temperatures and stresses simulated during steady operation and during fuel-to-cladding contact. A parameter variation study including 11,520 individual simulations with variations in nominal fuel thermal creep rate, cladding thermal conductivity, cladding irradiation creep and swelling, cladding gap size, and cladding thickness demonstrated that research priorities for this ATF should revolve around reducing cladding thickness as a means to minimize cladding failure. Generally, despite advances in SiC-SiC compliance, the brittle nature of mSiC excludes U 3 Si 2 -SiC for use where fuel cladding contact may occur.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Semi-integral LOCA test of cold-spray chromium coated zircaloy-4 accident tolerant fuel cladding

Enhancing the accident tolerance of PWRs came under serious consideration following the 2011 Fukushima Daiichi nuclear power plant events. While the current nuclear fuels are based on mature technology and have an excellent operational record, further enhancing their strength through accident tolerant fuel (ATF) research and development continues to be of interest. Particularly, the chromium coated clad ATF technology represents an evolutionary change to improve the high temperature performance of existing Zircaloy claddings. Additionally, despite several years of investigation of coated cladding, the integral loss of coolant accident (LOCA) performance of chromium coated cladding has had little attention. In this work, cold-spray chromium coated zircaloy-4 claddings are evaluated using EDF's semi-integral LOCA test facility. Results show that the chromium coating induces a reduced ballooning and burst and an increased burst temperature in the investigated conditions. However, these tests exhibit limited benefits concerning the post-quench behavior of the coated specimens which occurs in the last stage of a prototypical LOCA scenario.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Burst characteristics of advanced accident-tolerant FeCrAl cladding under temperature transient testing

Here assessment of burst characteristics of accident-tolerant fuel (ATF) claddings is essential to evaluate the safety margins of nuclear reactors, and better understanding can enable accelerated licensing for reactor concepts that include the new materials. Therefore, this study investigated the burst behavior of an ATF candidate of C26M, which is an iron–chromium–aluminum alloy (FeCrAl) under transient testing like the simulated loss-of-coolant accident (LOCA) conditions, except the water-quenching phase, in light-water reactors (LWRs). The effect of LOCA specimen length was assessed in terms of post-burst tube parameters. No critical length effect was determined on the burst pressure, burst location, and burst size measurements. Burst temperature showed larger variation likely due to its measurement approach used in this study. The post-test diametral strain was identified as the critical parameter to reduce the specimen length as compared to tube burst length or width. Postmortem optical metrology and digital image correlation were employed to determine the local strain-state during the simulated LOCA, which showed the loading path was close to equibiaxial conditions in regions away from the burst location, rather than internally pressurized conditions (or “plane-strain” tension). Pst-test microstructural characterizations of the FeCrAl revealed that ductile damage was present at the edge of the outer radial surface while the rest of the material was ruptured via cleavage at LOCA burst temperatures. Furthermore, internal grain boundary cracks were observed at locations away from the tube burst region. This behavior was considered to occur during the cooling down period of the simulated LOCA test. Overall, this study aimed to provide essential data for fuel performance code development by considering micromechanics of the deformation and failure.

36 MATERIALS SCIENCE↗
DOE OSTI2026

A comparison of wrought and powder metallurgical FeCrAl claddings under simulated LWR accident transients

Iron-chromium-aluminum (FeCrAl) alloys are potential accident tolerant fuel (ATF) cladding candidates for light-water reactors but are difficult to fabricate as thin-walled tubes via conventional cast-and-wrought routes. Powder metallurgy (PM) offers a manufacturing alternative with improved compositional control, but its transient accident performance has not been directly benchmarked against wrought variants. This study evaluates the burst behavior of commercially developed PM-processed FeCrAl alloys, PM-C26M (Fe-12Cr-6Al-2Mo) and the high precipitate density FA-SMT (Fe-22Cr-5Al-3Mo), under simulated light-water reactor accident transient conditions. Burst testing was conducted using the Severe Accident Test Station with heating rates of 5 °C/s and 50 °C/s and internal pressures ranging from 25 MPa to 100 MPa. PM-C26M reproduced wrought C26M burst behavior within 7–37 °C across the stress range, indicating that PM processing does not compromise transient strength. FA-SMT exhibited markedly higher burst temperatures and reduced heating-rate sensitivity, consistent with its engineered precipitate strengthening. FA-SMT rupture exhibited axial "unzipping" rather than the lateral tearing characteristic of PM- and wrought C26M. Post-test EBSD and fractography indicate that this behavior is strongly correlated with strain-gated intergranular void nucleation associated with the dense precipitate architecture of FA-SMT, a response absent in the comparatively clean PM-C26M matrix and consistent with rupture morphologies reported for oxide-dispersion strengthened (ODS) FeCrAl of similar base-matrix chemistry to PM-C26M. These findings highlight the potential of powder metallurgy as a viable fabrication route for ATF claddings from an accident performance standpoint.

Bell, Sam [ORNL] (ORCID:0000000251905657)↗
DOE OSTI2025

Thermal mechanical assessment of a SiC-SiC-composite clad fuel pin concept in a light water reactor environment

Accident Tolerant Fuels (ATFs) are designed to increase coping time following an accident scenario while preserving or improving current steady state reactor operational performance. A potential ATF concept is SiC-SiC composite claddings. Fuel performance simulations were conducted on a SiC-SiC based cladding concept utilizing a multilayered approach for improved performance. This cladding concept referred to as the Duplex concept is a duplex structure composed of a monolithic SiC layer placed on the outside of a SiC-SiC composite. A liquid metal is added to fuel-cladding gap for improved heat dissipation from the fuel. The monolithic SiC layer is used to improve the coolant corrosion characteristics and protect the SiC-SiC composite layer from exposure to the coolant. The fuel performance code BISON was used to conduct fuel performance simulations on the cladding concepts. Comparisons are made with a current prototypic fuel rod design (UO 2 fuel enclosed in Zircaloy-4 cladding). Representative steady-state cases were considered for normal power and two cycle power histories. Additionally, a PCI ramp case was simulated to analyze potential anticipated operational occurrences. Transient response during a Loss of Coolant Accident and a Reactivity Initiated Accident were also simulated. This computational study demonstrated that for normal operating conditions, the SiC concept cladding performed as well as the baseline for the standard power cases evaluated. The ramping evaluations indicate potential fracturing of the SiC-SiC composite of the composite cladding compared to the Zircaloy-4 cladding due to the temperature gradient and the subsequent differential thermal conductivity degradation and swelling across the composite thickness. In conclusion, the rod fails early at low enthalpy for RIA but survives a LOCA with minimal material loss due to high temperature steam corrosion.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Block Tectonics across Western Tibet and Multi-Millennial Recurrence of Great Earthquakes on the Karakax Fault

We report that fault slip rates are critical to quantify continental deformation. Those along the Karakax fault (northwestern Altyn Tagh Fault: ATF) have been debated, even though it is one of Tibet's most outstanding active faults. At Taersa, using LiDAR measurements of terrace and fan riser offsets (~6 to ~500 m) and 10 Be/ 26 Al dating of alluvial surfaces (<210 ka), we obtain a late Quaternary slip rate of ~2.5 ± 0.5 mm/yr. This doubles the ~2.6 ± 0.5 mm/yr rate time span found to the east and west. We interpret the ~150 km-long, free-faced rupture along the fault to be that of the M ~ 7.6 event felt in Hotan in 1882. Characteristic slip (~6 m) during four large earthquakes since ~10 ka implies a ~2500 ± 500 years return time. A ~3 mm/yr rate is consistent with the ~80 km offset of the Karakax river since uplift of the West Kunlun range and sediment deposition in the Tarim foreland accelerated, ~24 Ma ago. The faster slip rate (~10.5 mm/yr) on the central ATF matches the sum of those along the reactivated West Tibetan terrane boundaries (Karakax and Longmu-Gozha Co faults) at the Uzatagh triple junction (~36°N, 83°E). The abrupt termination and altitude drop of the Karakorum range where the Longmu Co and Karakorum faults meet (Angmong junction), also reflect triple junction kinematics. Such localized changes account for the rise of the Karakorum and West Kunlun ranges and support lithospheric block tectonics rather than diffusely distributed deformation.

58 GEOSCIENCES↗
DOE OSTI2026

PWR Core Analysis for Cycle Extension and Uprates with LEU+ Accident Tolerant Fuel and 80 GWd/Tonne Burnup Limit

The U.S. Nuclear Regulatory Commission has recently drafted a rule enabling fuel burnup increase in light water reactors up to 80 GWd/t. In conjunction with use of fuel enrichment up to 10%, and accident tolerant fuel (ATF), this is anticipated to facilitate 24-month cycles in PWRs, along with further power uprates. In this paper, PWR core analysis is performed for 20% increased PWR power output along with cycle extension up to 24 months, in combination with use of chromia-doped fuel and chromium-coated clad, considered to be the most near-term ATF concepts. In combination, these lead to challenging conditions with a core average discharge burnup of up to ~74 GWd/t, challenging even the 80 GWd/t burnup limit. Analysis is performed using the 2-step method with POLARIS (within SCALE) used for the lattice calculations and PARCS for the core calculations. Core designs are first baselined for current operating conditions (LEU, 62 GWd/t discharge burnup limit) and then derived that meet cycle constraints on power distribution and the updated lead pin discharge burnup limit while maintaining at least two batches of fuel in the core. Gadolina loadings in fuel pins of up to 8% are used, with enrichment zoning both within the core and, to a limited extent, within assemblies. Here, doped fuel with coated cladding can utilize the same core designs as the reference UOX cores, exhibiting slightly lower burnup due to higher fuel density, which also offsets the slight reactivity penalty from the doping and coating. For the analysis performed here, doped fuel enabled a core with 24-month cycle and 20% uprate to stay within the 80 GWd/t lead pin discharge burnup limit.

LEU+↗
DOE OSTI2021

Extended Enrichment Accident Tolerant LWR Fuel Isotopic and Lattice Parameter Trends

Commercial light water reactor (LWR) operators and fuel vendors in the United States (US) are pursuing changes to the reactor fuel that include increased enrichment and accident-tolerant fuel (ATF) designs. Enrichments under consideration are between 5 wt % and 10 wt % 235 U, which are a subset of high-assay low-enriched uranium fuels. ATF features are designed to improve fuel system performance under accident conditions. With increased enrichment, fuel cycle economics can be improved if fuel can be licensed for higher burnup (HBU) than typical current limits (e.g., 62 GWd/MTU maximum fuel pin).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

High Level Gap Analysis for Accident Tolerant and Advanced Fuels for Storage and Transportation

This initial gap analysis considers proposed accident tolerant fuel (ATF) options currently being irradiated in commercial reactors, since these are most likely for future batch implementation. Also, advanced fuel (AF) options that may be likely for use in advanced reactors are considered. The cladding technologies considered were chromium-coated zirconium-based alloys, FeCrAl, and both monolithic and matrix composite Silicide carbide (SiC). The fuel technologies considered were chromium-doped uranium dioxide fuel, uranium alloys, uranium nitride, and uranium silicide. Numerous national labs, industry, and countries are performing significant testing and modeling on these proposed technologies to establish performance, but at this time none of the prototypes being irradiated have achieved end-of-life (EOL) burnup. There are some testing results after one burnup cycle to verify in-reactor performance, but little data beyond that. As the ATF prototypes acquire more burnup, data will be produced that is relevant to storage and transportation. The DOE:NE Spent Fuel and Waste Science and Technology (SWFST) Storage and Transportation (ST) Control Account will evaluate the performance data as it becomes available for application to the identified gaps for ST.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

STEP Report on Advanced ODS FeCrAl Alloys for Fission Applications

Oak Ridge National Laboratory is developing advanced low-Cr oxide dispersion strengthened (ODS) FeCrAl alloys for accident tolerant fuel (ATF) cladding. This report presents the characterization of two new ODS FeCrAl tubes by using powder commercially mechanically alloyed by Zoz GmbH, which underwent high-precision tube rolling with two different annealing schedules. This work shows that the ODS FeCrAl tube without recrystallization exhibits consistent mechanical behavior in comparison with a previously produced tube. The second tube, which underwent a full recrystallization step before the final tube rolling step, showed some circumferential cracking and exhibited limited ductility in the axial tube tensile tests. Based on current and prior work on the ODS FeCrAl alloy system, this report compares the current state of the scientific literature on the alloy class with that of wrought FeCrAl without oxide additions. Then, this report makes recommendations for future research directions that should be undertaken to increase the technology readiness level for ODS FeCrAl as a viable ATF candidate material. This report has been submitted as fulfillment of milestone M3FT-20OR020202064 titled, “STEP Report on Advanced ODS FeCrAl Alloys for Fission Applications” for the US Department of Energy Office of Nuclear Energy’s Advanced Fuel Campaign of the Fuel Cycle R&D program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Degradation and Failure Phenomena of Accident Tolerant Fuel Concepts: FeCrAl Alloy Cladding

The U.S. Nuclear Regulatory Commission (NRC) is anticipating licensing applications and commercial use of accident tolerant fuel (ATF) in United States commercial nuclear power reactors. Pacific Northwest National Laboratory is providing technical assistance to the NRC related to the newly proposed nuclear fuel and cladding designs. This report focuses specifically on the iron-chromium-aluminum (FeCrAl) alloys being investigated to replace zirconium-based alloys for fuel cladding and provides current state-of-the-industry information on material properties and fuel performance considerations under reactor operating conditions and design basis accident conditions. Currently, Global Nuclear Fuels (GNF) is the only U.S.-based fuel vendor considering FeCrAl cladding as a near-term ATF design. GNF has tested several different FeCrAl alloys including Kanthal APMT, C26M, and MA956; fueled C26M rods and unfueled Kanthal APMT, C26M, and MA956 rods have been inserted in lead test assemblies at Plants Hatch and Clinton. This report will focus on those three alloys specifically, with broader information given regarding in-reactor and ex-reactor testing of FeCrAl alloys. To support the NRC’s readiness efforts, this report will identify and discuss degradation and failure modes of FeCrAl cladding concepts, including fuel performance characteristics that may not be addressed within existing regulatory documents.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Nuclear Fuel Cycle and Supply Chain (NFCSC) Technical Monthly September FY-24

AFC hosted the Light Water Reactor (LWR) Fuels Research Workshop and Electric Power Research Institute (EPRI) Collaborative Research on Advanced Fuel Technologies (CRAFT) Meeting September 9-13, 2024. The Department of Energy's (DOE) Advanced Fuels Campaign (AFC) Accident Tolerant Fuel (ATF) program is pivotal in advancing clean energy through collaborative innovation in fuel technology for light water reactors (LWRs). For over a decade, AFC has engaged a wide array of stakeholders—researchers, industry participants, and regulatory bodies—both within the U.S. and internationally to develop ATF technology. This initiative aims to enhance the safety and economic performance of both Pressurized Water Reactors (PWRs) and LWRs. To foster community relationships and disseminate research, AFC initiated annual LWR Fuel workshops in 2024, supplementing ongoing industry-led CRAFT workshops.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Irradiation Testing Plan for Long Term Accident Tolerant Fuels

Many potential Accident Tolerant Fuel (ATF) technologies with the potential for making substantive improvements to the performance of Light Water Reactors (LWRs) in accident scenarios will require development and qualification timelines longer than 4 years. These technologies are named “Long Term” ATF. The attached report summarizes the irradiation testing capabilities available for use in the development and qualification of these technologies and presents a nominal test sequence.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Effect of Cr and Al on Elastic Constants of FeCrAl Alloys Investigated by Molecular Dynamics Method

The FeCrAl alloy system is recognized as one of the candidate materials for accident-tolerant fuel (ATF) cladding in the nuclear power industry due to its high oxidation resistance under irradiation and high-temperature environments. The concentrations of Cr and Al have a significant effect on elastic properties of the FeCrAl alloy. In this work, elastic constants C 11 , C 12 , C 44 , bulk modulus and shear modulus of FeCrAl alloy were calculated with molecular dynamics methods. We explored compositions with 1–15 wt.% Cr and 1–5 wt.% Al at temperatures from 0 K to 750 K. The results show that the concentrations of Al and Cr have different effects on the elastic constants. When the concentration of Al was fixed, a decrease in bulk modulus and shear modulus with increasing Cr content was observed, consistent with previous experimental results. The dependence of elastic constants on temperature was also the same as in the experiments. Investigations into elastic properties of defect-containing alloys have shown that vacancies, voids, interstitials and Cr-rich precipitations have different effects on elastic properties of FeCrAl alloys. Investigations of elastic properties of defect-containing alloys have shown that vacancies, void, interstitials and Cr-rich precipitations have different effects on elastic properties of FeCrAl alloys. Therefore, the present results indicate that both the Cr and Al concentrations and radiation defects should be considered to develop and apply the FeCrAl alloy in ATF design.

36 MATERIALS SCIENCE↗
NASA NTRS1972

Design, fabrication and testing of a thermal diode

Heat pipe diode types are discussed. The design, fabrication and test of a flight qualified diode for the Advanced Thermal Control Flight Experiment (ATFE) are described. The review covers the use of non-condensable gas, freezing, liquid trap, and liquid blockage techniques. Test data and parametric performance are presented for the liquid trap and liquid blockage techniques. The liquid blockage technique was selected for the ATFE diode on the basis of small reservoir size, low reverse mode heat transfer, and apparent rapid shut-off.

Swerdling, B.↗
NASA NTRS1973

Variable conductance heat pipes from the laboratory to space

Heat pipes were developed which can be used as (1) a variable conductance link between a heat source and sink which provides temperature stability; (2) a feedback control mechanism that acts to directly maintain the source at a constant temperature; (3) or as a thermal diode that allows heat to be transferred in one direction only. To establish flight level confidence in these basic control techniques, the Ames Heat Pipe Experiment (AHPE) was launched in August 1972 and the Advanced Thermal Control Flight Experiment (ATFE) is scheduled for launch in May 1973. The major efforts of the technology development, initial flight results of the AHPE, and ground test data of the ATFE are discussed.

Kirkpatrick, J. P.↗
NASA NTRS1976

Long term performance of the advanced thermal control flight experiment

The Advanced Thermal Control Flight Experiment (ATFE) is providing the first zero-g flight data for the performance of a thermal diode heat pipe and an electrical Feedback Controlled Heat Pipe (FCHP). The temperature stability derived from the melting and freezing of octadecane is also being evaluated in this experiment. Flight data for the different operational modes are compared to ground test data, and the performance of the individual components is analyzed. Also, the ATFE's long term behavior from launch through September 30, 1975, is evaluated. The temperature control capability of a thermal diode, phase change material, and FCHP was demonstrated over more than 500 days of flight operation and each of these components should be considered in future applications. Both the diode and FCHP transport more than 20 W in the normal and passive modes during maximum conditions. Up to 30 W has been carried by the FCHP when the auxiliary heater is applied. The "OFF-conductance" of the diode has improved substantially in flight. A 1.4 W decrease in backflow has been realized by more complete blockage. The variable conductance behavior of the FCHP is essentially unchanged with time and relative to ground tests. Degradation of the radiator and reservoir surfaces have resulted in a partial loss of control by the FCHP during normal mode operation; however, manual control at an elevated set point has demonstrated the FCHP's ability to provide regulated temperature control to within + or - 2 C. The same pipe when operated as a passive VCHP controlled at 35 + or - 10 C with the same test conditions.

Brennan, P. J.↗