Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “36 MATERIALS SCIENCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Influence of minor Ce additions on magnetic and electrical properties in Fe–6.5 wt. % Si alloy

Fe–6.5 wt. % Si alloys exhibit lower core loss at higher frequency than the dominating electrical steel containing 3.2% Si due to its lower magneto-crystalline anisotropy energy (MAE) and higher electrical resistivity. However, compared to nanocrystalline and amorphous soft-magnetic materials, 6.5% Si steel, although being cost effective and having high saturation magnetization, still has much to improve, especially with respect to MAE and resistivity. To explore further improvement, the effects of minor Ce additions (due to its mixed valence 4f-electron configuration) on the microstructure, electrical and magnetic behaviors of Fe–6.5 wt. % Si alloys were investigated. Due to its limited solubility in Fe, Ce exhibits condition-dependent effects on electrical resistivity, showing only marginal improvement under rapid solidification. In contrast, Ce addition degrades magnetic performance, reducing saturation magnetization (from 1.86 to 1.76 T) and increasing coercivity (from 88 to 171 A/m), which results in an 83.4% increase in core loss (W 10/1000 condition). Overall, Ce addition provides limited benefit in electrical resistivity while deteriorating magnetic properties, making it ineffective for enhancing the soft magnetic performance of Fe–6.5 wt. % Si alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Uniaxial tensile mechanical properties from a scratch on ultra-fine grained tungsten

We demonstrate that surface-based mechanical testing can be used to quantify a wide range of mechanical properties determined using traditional uniaxial tension experiments. These include mapping of dynamic stress–strain behaviour, which can be used as a screening tool for uniaxial tensile ductility (uniform elongation), fracture toughness (K C ), which is shown to be in good agreement with reported plane-strain K IC , as well work-hardening exponents (n), activation volumes (V) energies (Q) and strain-rate sensitivity (m) exponents as a function of temperature. Advantages of the surface-based approach are the ability to work with significantly smaller volumes and accommodate processing defects like pores, voids and cracks. These methods are applied to ultra-fine grained tungsten (average grain size of 650 nm), as it is an ideal candidate for alloy development efforts in advanced energy systems. Tungsten is a useful baseline as it exhibits a near-ambient temperature (approx. 200°C) ductile-to-brittle transition temperature (DBTT), enabling validation efforts for the proposed methods, and extraordinary material properties, including the highest melting temperature of any metal and complex temperature and strain-rate dependencies linked to transitions in dislocation mechanisms.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Iron speciation in blast furnace slag cements

Slag-containing pastes and concretes were analysed by element-specific synchrotron-based techniques to determine the speciation of iron on crushed materials through spatially resolved micro-spectroscopic studies. The investigated cement samples were hydrated either in the laboratory, or exposed to river or sea water. Metallic iron, along with minor proportions of iron sulphide and magnetite was detected in the laboratory sample. Iron sulphide, goethite, and siliceous hydrogarnet were discovered in the blended slag cements hydrated in contact with river water for up to 7 years. In contrast, no Fe(0) was observed in blended concretes exposed to sea water. Instead, iron sulphide, iron(II)-hydroxide and -oxide, hematite, magnetite, siliceous hydrogarnet, and goethite were detected as well as ilmenite (FeTiO{sub 3}) in the aggregates. The strong acceleration of Fe oxidation in samples exposed to sea water and the long-term passivation observed in the other samples indicate comparable processes as those occurring on steel bars.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Intrinsic self-stressing and low carbon Engineered Cementitious Composites (ECC) for improved sustainability

Highlights: • A self-stressing criterion for ECC was established and experimentally verified. • An intrinsic self-stressing ECC was developed by utilizing LC3 and CSA cement. • Initial maximum expansion and later expansion loss were successfully tailored. • Expansion mechanism was identified by XRD patterns. • Self-stressing ECC has 64% of the carbon footprint of conventional concrete. Engineered Cementitious Composites (ECC) is an emerging cementitious composite material with ultra-high ductility. However, its higher cement dosage limits its material greenness and leads to concerns with drying shrinkage. In this research, an ECC utilizing limestone calcined clay cement (LC3) and calcium sulphoaluminate cement (CSA) is investigated, focusing on minimizing the material's embodied carbon while enhancing its durability with intrinsic self-stressing functionality. A self-stressing criterion is theoretically established and experimentally verified. X-ray diffraction patterns reveal an ettringite quantity that modulates the initial expansion and later expansion-reversal of LC3-CSA-ECC to support a persistent self-stressing mechanism. LC3-CSA-ECC has a lower (64%) carbon footprint and similar embodied energy compared to conventional concrete. When combined with the durability advantage (tiny crack, high ductility of 5.5%, and self-stressing function), this low carbon self-stressing ECC holds promise as a sustainable repair material that lowers the embodied and operational carbon in civil infrastructure.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Self-Assembly of Partially Charged Diblock Copolymer-Homopolymer Ternary Blends

Ternary blends comprising of a diblock copolymer and the corresponding homopolymers provide ready access to a variety of morphologies, but the impact of charge on their phase behavior has not been studied extensively. Here, three partially charged ternary blends consisting of symmetric poly[(oligo(ethylene glycol) methyl ether methacrylate-co-oligo(ethylene glycol) propyl sodium sulfonate methacrylate)] (POEGMA#), polystyrene (PS), and POEGMA#-PS with different charge fractions were prepared, where # denotes the mole fraction of charged monomers in the POEGMA chain. Here, the phase behavior was systematically studied using small-angle X-ray scattering (SAXS), and isothermal phase diagrams at 120 °C were constructed. The resulting isothermal planes contain a wide lamellar (LAM) phase window with a slight deviation from symmetry for ion-containing ternary blends, due to the homopolymer size difference. Given the absence of any significant change in the phase diagrams as the charge fraction increases, the role of charge is primarily to increase the segregation strength in the ternary system, as in the case of partially charged diblock polymers. In addition, examination of the increase in domain size along the volumetrically symmetric isopleth reveals a “dry-brush” like swelling behavior of homopolymers in all three blends, presumably due to the space-filling nature of the oligomeric ethylene glycol side chains on POEGMA.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Comparative Studies of Optoelectrical Properties of Prominent PV Materials: Halide Perovskite, CdTe, and GaAs

We compare three representative high performance PV materials: halide perovskite MAPbI3, CdTe, and GaAs, in terms of photoluminescence (PL) efficiency, PL lineshape, carrier diffusion, and surface recombination and passivation, over multiple orders of photo-excitation density or carrier density appropriate for different applications. An analytic model is used to describe the excitation density dependence of PL intensity and extract the internal PL efficiency and multiple pertinent recombination parameters. A PL imaging technique is used to obtain carrier diffusion length without using a PL quencher, thus, free of unintended influence beyond pure diffusion. Our results show that perovskite samples tend to exhibit lower Shockley-Read-Hall (SRH) recombination rate in both bulk and surface, thus higher PL efficiency than the inorganic counterparts, particularly under low excitation density, even with no or preliminary surface passivation. PL lineshape and diffusion analysis indicate that there is considerable structural disordering in the perovskite materials, and thus photo-generated carriers are not in global thermal equilibrium, which in turn suppresses the nonradiative recombination. This study suggests that relatively low point-defect density, less detrimental surface recombination, and moderate structural disordering contribute to the high PV efficiency in the perovskite. This comparative photovoltaics study provides more insights into the fundamental material science and the search for optimal device designs by learning from different technologies.

14 SOLAR ENERGY↗
DOE OSTI2022

Anisotropic magnetic and transport properties of orthorhombic o-Pr 2 Co 3 Ge 5

Abstract The crystal structure, electron energy-loss spectroscopy (EELS), heat capacity, and anisotropic magnetic and resistivity measurements are reported for Sn flux grown single crystals of orthorhombic Pr 2 Co 3 Ge 5 (U 2 Co 3 Si 5 -type, Ibam ). Our findings show that o -Pr 2 Co 3 Ge 5 hosts nearly trivalent Pr ions, as evidenced by EELS and fits to temperature dependent magnetic susceptibility measurements. Complex magnetic ordering with a partially spin-polarized state emerges near T sp = 32 K, with a spin reconfiguration transition near T M = 15 K. Heat capacity measurements show that the phase transitions appear as broad peaks in the vicinity of T sp and T M . The magnetic entropy further reveals that crystal electric field splitting lifts the Hund’s rule degeneracy at low temperatures. Taken together, these measurements show that Pr 2 Co 3 Ge 5 is an environment for complex f state magnetism with potential strongly correlated electron states.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Plastic deformation mechanism of calcium-silicate hydrates determined by deviatoric-stress Raman spectroscopy

Highlights: • C-(A-)S-H samples under stress were characterized at the bond and grain level. • Small angle scattering showed that 720 MPa reduced grain thickness by 30%. • In-situ Raman showed that cross-linked C-A-S-H slips along its intralayer. • However, in-situ Raman showed that C-S-H slips along the interlayer. • In-situ Raman also showed a growth in CaCO{sub 3}, indicating fracture in both samples. Creep of the cement matrix affects the structural stability of concrete. In Portland cements, the creep is largely controlled by the binding phase calcium-(aluminum-)silicate-hydrate, or C-(A-)S-H. This phase has a lamellar structure and under deviatoric stress aligns its c-axis with the principal stress. However, the limiting resistance to this reorientation is unknown at the nanocrystalline level. Small-angle X-ray scattering shows that the lamellae thickness decreases under 100's MPa deviatoric stress. Deviatoric stress Raman spectroscopy shows that there are two ways that this break-up can occur. If the material's silicate chains are cross-linked, then strain in SiO bonds does not increase above certain stresses, indicating a relaxation adjacent to the SiO bond. If the chains are not cross-linked, then the silicate chains are broken up by rastering against each other, introducing defects. These results show that the plastic deformation of C-(A-)S-H is relevant for Portland cement creep.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructure and water absorption of ancient concrete from Pompeii: An integrated synchrotron microtomography and neutron radiography characterization

There is renewed interest in using advanced techniques to characterize ancient Roman concrete due to its exceptional durability and low-carbon footprint. In the present work, samples were drilled from the “Hospitium” in Pompeii and were analyzed by synchrotron microtomography (μCT) and neutron radiography to study how the microstructure, including the presence of induced cracks, affects their water adsorption. The water distribution and absorptivity were quantified by neutron radiography. The 3D crack propagation, pore size distribution and orientation, tortuosity, and connectivity were analyzed from μCT results using advanced imaging methods. Porosity was also measured by mercury intrusion porosimetry (MIP) as a reference. Ductile fracture patterns were observed once cracks were introduced. Compared to Portland cement mortar/concrete, the Pompeii samples had relatively high porosity, low connectivity, and a similar coefficient of capillary penetration. In addition, permeability was predicted from models based on percolation theory and pore structure data to evaluate the fluid transport properties. Understanding the microstructure of ancient Pompeii concrete is important because it could inspire the development of modern concrete with high durability.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Creating and Interfacing Designer Chemical Qubits (Final Technical Report)

The Final Technical Report describes a multi‑institution effort to develop programmable molecular qubits as precision quantum sensors for probing quantum materials. The team created chemically tunable qubits with optical addressability and practical coherence, integrated them into thin films and frameworks while preserving functionality, and established new magnetic and electric sensing methods suited to two‑dimensional magnets, ferroelectrics, and multiferroics. They also built computational models and spectroscopic tools that connect molecular design to material behavior, enabling access to quantum phenomena that previously could not be measured. The project produced more than 40 publications and trained a large cohort of graduate students and postdocs, strengthening the workforce and infrastructure needed for DOE's quantum information science mission.

2D Quantum Materials↗
DOE OSTI2024

Accelerating Thermochemical Equilibrium Calculations for Nuclear Reactor Applications

Thermochemical properties play a key role in modeling and simulation of several key phenomena in nuclear reactors. There has been an increasing interest in incorporating CALPHAD-based formulations in multiphysics simulations including for Molten Salt Reactors where knowledge of phase evolution of the salt and the chemical potentials of various elements are of utmost importance in source term analyses and redox control. However, the size of such simulations is often limited by the high computational cost of full thermodynamic equilibrium calculations. This work discusses the current efforts aimed at accelerating thermochemical equilibrium calculations for multiphysics simulations performed using the open-source finite element / finite volume code Multiphysics Object Oriented Simulation Environment (MOOSE) [1]. While several methods have been proposed for accelerating phase equilibrium calculations [2], most focus on relatively small systems and often rely on a- priori knowledge of the state-space of the system. Nuclear materials, however, are often multi-component systems owing to the evolution of composition under irradiation and an approach based on a-priori mapping of phase diagram is often not enough. This work is aimed at demonstrating an on-the-fly surrogate modeling framework that uses active learning to reduce the number of full equilibrium calculations that must be performed. By combining with efficient coupling approaches, the surrogate framework helps in reducing the computational cost of thermodynamic equilibrium informed multiphysics simulations of nuclear materials. The performance is benchmarked against full coupling with the thermochemistry library Thermochimica [3]. This work uses a machine learning based approach for constructing surrogate models to predict the stable phases in a multicomponent system. The surrogates were constructed using neural networks and Gaussian process classification. In this work, we compare the relative performance of the two methods. We also demonstrate the use of caching previous calculations by interpolating the values from nearest neighbors. References [1] Lindsay, A.D., et al. "2.0 – MOOSE: Enabling massively parallel multiphysics simulation", SoftwareX, 20 (2022): 101202. [2] Roos, W.A. and Zietsman J.H. "Accelerating complex chemical equilibrium calculations – A Review", Calphad, 77 (2022): 102380. [3] Piro, M.H.A., et al. "The thermochemistry library Thermochimica", Computational Materials Science, 67 (2013): 266-272.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Temperature-Dependent Mechanical Anisotropy in Textured Zircaloy Cladding

This work evaluates deformation activity in textured zircaloy-4 cladding with the aim of elucidating the mechanisms that govern mechanical behavior across a temperature range anticipated in reactor service. In particular, the dependence of mechanical anisotropy on temperature and stress state (ratio of applied stresses) is examined via uniaxial and biaxial tensile experiments at room temperature and 400 °C. The mechanical behavior was interpreted based on micro-texture and dominant slip system activity. Thermal activation of basal systems is found as a key mechanism affecting mechanical behavior across the temperature range. The biaxial stress states produce resolved shear stresses contrasting to uniaxial stress states. As a result, mechanical testing and implications for reactor pellet-cladding mechanical interaction stress conditions are discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Interferometric bunch length measurements of 3 MeV picocoulomb electron beams

We report picosecond bunch length measurements using an interferometric method for a 3 MeV electron beam having bunch charge ranging from 1 to 14 pC. The method senses the single-cycle sub-terahertz (THz) pulse emitted by each electron bunch as coherent transition radiation which, in turn, is analyzed using a Michelson-type interferometer, forming an interferogram that is then processed to yield the nominal electron bunch length. This sub-THz coherent radiation intensity was measured using a quasi-optical detector (QOD) operated at room temperature. This experiment was quite challenging since the divergence angle of the sub-THz pulse emitted by the low-energy electron bunch exceeds ±10°, and its pulse energy at the entrance to the detector was as low as 100 pJ. When compared to a conventional helium-cooled silicon composite bolometer designed for frequencies above 0.5 THz, the QOD provided much better signal-to-noise ratio in the ~80 GHz frequency range, which was critical for the successful measurement of the bunch length.

36 MATERIALS SCIENCE↗
DOE OSTI2021

New insights into the mechanism governing the elasticity of calcium silicate hydrate gels exposed to high temperature: A molecular dynamics study

When exposed to fire, the integrity of cement-based materials is governed by thermally-induced changes in the mechanical properties of their binding phase, i.e., the calcium–silicate–hydrate (C–S–H) gel. However, the effect of temperature on the structure, density, and mechanical properties of C–S–H remains only partially known. Here, based on reactive molecular dynamics simulations, we reveal the nature of thermally-induced damage in C–S–H gels. In general, we show that, at the atomic scale, exposure to high temperature results in partial dehydration, volumetric shrinkage, disordering, and stiffening in the C–S–H grains. However, we show that the thermal response of C–S–H strongly depends on its chemical composition, wherein C–S–H systems associated with lower Ca/Si molar ratios are able to undergo higher temperatures before amorphization. Based on these results, we demonstrate that the stiffness of C–S–H gels (i.e., including porosity—as probed by nanoindentation) is governed by a competition between the stiffening of the grains and the decrease in packing density—wherein the latter eventually become predominant.

36 MATERIALS SCIENCE↗