Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wind blades”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

Blade Displacement Predictions for the Full-Scale UH-60A Airloads Rotor

An unsteady Reynolds-Averaged Navier-Stokes solver for unstructured grids is loosely coupled to a rotorcraft comprehensive code and used to simulate two different test conditions from a wind-tunnel test of a full-scale UH-60A rotor. Performance data and sectional airloads from the simulation are compared with corresponding tunnel data to assess the level of fidelity of the aerodynamic aspects of the simulation. The focus then turns to a comparison of the blade displacements, both rigid (blade root) and elastic. Comparisons of computed root motions are made with data from three independent measurement systems. Finally, comparisons are made between computed elastic bending and elastic twist, and the corresponding measurements obtained from a photogrammetry system. Overall the correlation between computed and measured displacements was good, especially for the root pitch and lag motions and the elastic bending deformation. The correlation of root lead-lag motion and elastic twist deformation was less favorable.

Bledron, Robert T.↗
DOE OSTI2025

Upwind vs. downwind: loads and acoustics of a 1.5 MW wind turbine

This paper discusses the motivation, preparation, risk mitigation, execution, and results of a full-scale experiment where the conventional upwind rotor of a 1.5 MW wind turbine was operated in a downwind configuration. The experiment took place at the National Renewable Energy Laboratory Flatirons Campus in Colorado, USA, and involved the collection of loads and power together with acoustic measurements from an array of four microphones. To validate the numerical predictions of the aeroelastic solver OpenFAST in terms of loads and performance, 410 min of downwind operation and 960 min of conventional upwind operations were used. In the wind speed range from 4.5 to 12.5 m s−1, the downwind rotor generates higher damage equivalent loads for the blade root flapwise moment, blade root edgewise moment, and tower-base fore-aft moment compared to the upwind rotor. For these metrics of fatigue loads, numerical predictions match the experimental observations well. OpenFAST is, however, also seen underpredicting a power gain in the downwind rotor. In terms of acoustics, the overall sound pressure levels recorded in the field are similar between the upwind and downwind cases, but downwind operation worsens the metrics describing amplitude modulation.

17 WIND ENERGY↗
NASA NTRS1980

A comparison between an existing propeller noise theory and wind tunnel data

The noise of three supersonic helical tip speed propellers was compared with the noise predicted by an existing noise theory. Comparisons of the peak blade passage tones showed fairly good agreement beween theory and experiment at the lowest helical tip Mach numbers tested, 0.86 and 1.00, while at higher numbers, the theory predicted higher noise levels than measured. When the differences among the propellers were considered the theory and measurement showed fairly good agreement. Directivity measurements in general showed that the measured blade passage tone data peaked further downstream than the theory predicted. At the cruise design condition the harmonics appeared to fall off faster in the data than the theory indicated.

Dittmar, J. H.↗
NASA NTRS1981

North Wind 4kW passive control system design

An overview of a mechanical rotor control design is presented. Operation at constant RPM and rapid response are obtained by using blade pitch moments for both sensing control need and blade pitch actuation. The basic concept, static or equilibrium design, and dynamic analysis are briefly presented.

Currin, H.↗
NASA NTRS1977

Design and performance of energy efficient propellers for Mach 0.8 cruise

It is believed that a fuel saving of 14 to 40 percent may be realized by the use of an advanced high-speed turboprop. This turboprop must be capable of high efficiency at Mach 0.8 cruise above 9.144 km altitude if it is to compete with turbofan powered commercial aircraft. Several advanced aerodynamic concepts were investigated in recent wind tunnel tests under NASA sponsorship on two propeller models. These concepts included aerodynamically integrated propeller/nacelles, area-ruling, blade sweep, reduced blade thickness and power (disk) loadings several times higher than conventional designs. The aerodynamic design methodology for these models is discussed in this paper. In addition, some of the preliminary test results are presented which indicate that propeller net efficiencies near 80 percent were obtained for high disk loading propellers operating at Mach 0.8.

Mikkelson, D. C.↗
NASA NTRS1977

Some measured and calculated effects of a tip vortex modification device on impulsive noise

The results of a recent wind tunnel test program to evaluate the effectiveness of the Tip Air Mass Injection (TAMI) system in modifying the blade tip vortex occurring during helicopter flight is described with attention to the effect of this modification on the impulsive noise. The measurement program is explained, and the correlation between experimental and predicted results is discussed. Topics considered include the effect of descent rate on noise pressure time histories, the effect of air mass injection on noise, and the analysis based on a dB(A) weighted approach. Impulsive noise generated by the interaction of a helicopter rotor blade and the concentrated tip vortex during forward flight descent is a primary contributor to acoustic annoyance as it draws early attention to the presence of the helicopter.

Pegg, R. J.↗
NASA NTRS1978

Aeroelastic analysis of wind energy conversion systems

An aeroelastic investigation of horizontal axis wind turbines is described. The study is divided into two simpler areas; (1) the aeroelastic stability of a single blade on a rigid tower; and (2) the mechanical vibrations of the rotor system on a flexible tower. Some resulting instabilities and forced vibration behavior are described.

Dugundji, J.↗
NASA NTRS1978

A new blade element method for calculating the performance of high and intermediate solidity axial flow fans

A method is presented to design and predict the performance of axial flow rotors operating in a duct. The same method is suitable for the design of ducted fans and open propellers. The unified method is based on the blade element approach and the vortex theory for determining the three dimensional effects, so that two dimensional airfoil data can be used for determining the resultant force on each blade element. Resolution of this force in the thrust and torque planes and integration allows the total performance of the rotor, fan or propeller to be predicted. Three different methods of analysis, one based on a momentum flow theory; another on the vortex theory of propellers; and a third based on the theory of ducted fans, agree and reduce cascade airfoil data to single line as a function of the loading and induced angle of attack at values of constant inflow angle. The theory applies for any solidity from .01 to over 1 and any blade section camber. The effects of the duct and blade number can be determined so that the procedure applies over the entire range from two blade open propellers, to ducted helicopter tail rotors, to axial flow compressors with or without guide vanes, and to wind tunnel drive fans.

Borst, H. V.↗
NASA NTRS1979

Design evolution of large wind turbine generators

During the past five years, the goals of economy and reliability have led to a significant evolution in the basic design--both external and internal--of large wind turbine systems. To show the scope and nature of recent changes in wind turbine designs, development of three types are described: (1) system configuration developments; (2) computer code developments; and (3) blade technology developments.

Spera, D. A.↗
NASA NTRS1980

Large Wind Energy Converter: Growian 3 MW

The final report on the projected application of larger-scale wind turbine on the northern German coast is summarized. The designs of the tower, machinery housing, rotor, and rotor blades are described accompanied various construction materials are examined. Rotor blade adjustment devices auxiliary and accessory equipment are examined.

Feustel, J. E.↗
NASA NTRS1981

Tests of an overrunning clutch in a wind turbine

An overrunning clutch that slipped freely under reverse torque was tested in the drive train of the Mod-0 wind turbine. In low variable wind conditions, the clutch engaged and disengaged smoothly without perturbation or oscillations. The clutch permitted the generator to be connected to the line using a relay instead of an automatic synchronizer. The alternator was connected to the line when the rpm reached 95% of synchronous speed and it motored to synchronous speed in about 0.15 seconds with a momentary power spike of 50 kW. The performance of the clutch was the same with and without the fluid coupling. The ideal power with the clutch was 5 to 7 kW compared to up to 50 kW without the clutch. The overrunning clutch merits consideration in future wind turbine designs as a means of simplifying the control system, increasing energy capture, and increasing the life of blades and electrical switch gear.

Seidel, R. C.↗
NASA NTRS1981

Zero-length inlets for subsonic V/STOL aircraft

Zero-length inlet performance and associated fan blade stresses were determined during model tests in the NASA-LeRC 9-by 15-foot low-speed wind tunnel. The inlet models, which were installed on a 20-inch diameter fan unit, had different inlet lip contraction ratios as well as unslotted, slotted, and double slotted inlet lips. The inlet angle-of-attack boundaries for onset of flow separation were identified and compared to the operating requirements of several generically different subsonic V/STOL aircraft. The zero-length inlets, especially those with slotted lips, were able to satisfy these requirements without compromising the maximum cowl forebody radius. As an aid to the inlet design process, a unique relationship was established between the maximum surface Mach number associated with the separation boundary and the maximum-to-throat surface velocity ratio.

Glasgow, E. R.↗
NASA NTRS1983

Aeroacoutic characteristics of a large, variable-pitch, variable-speed fan system

The acoustic and aerodynamic performance of the new drive fans for the NASA Ames 40- by 80-/80- by 120-foot wind tunnel was investigated. Results show that a fan system with variable-speed and variable-pitch rotor blades allows the operator to control noise and energy consumption, at a given mass flow rate, through the choice of blade speed and pitch. A low speed and high blade pitch will generally create the least noise at the least energy cost. An empirical method is described which predicts the sound power of this fan system reasonably well.

Soderman, P. T.↗
NASA NTRS1985

Fabrication of Slender Struts for Deployable Antennas

High moduli of elasticity potentially achievable. Suited for application in large diameter antennas on orbiting spacecraft. Fabrication process can accurately place dry graphite fibers and overwrap them with aluminum foil, resulting in straight, slender graphite tubes. Graphite fibers pulled out of creeled spools and fed through ceramic eyelets. Spools of aluminum foil mounted on rotating ring and capture graphite fiber as vertical winding machine carriage moves upward. Epoxy resin applied by mechanically spreading epoxy on tetrafluoroethylene mandrel by means of doctor blade attached to carriage.

Bush, H. G.↗
NASA NTRS1984

Results of S5 CH tests with an ARL (Aerospace Research Laboratory) cascade

As part of a research agreement between Iowa State University of Science and Technology (ISU) and ONERA, a blade cascade designed and already tested in the United States was manufactured and tested in France. The ONERA cascade wind tunnel and mock-up are described. Attention is focused on defining the upstream conditions of the cascade. Experimental results are presented, as well as comparisons with tests conducted by Detroit Diesel Allison (DDA) in the United States.

Fourmaux, A.↗
NASA NTRS1993

Takeoff/approach noise for a model counterrotation propeller with a forward-swept upstream rotor

A scale model of a counterrotating propeller with forward-swept blades in the forward rotor and aft-swept blades in the aft rotor (designated F39/A31) has been tested in the NASA Lewis 9- by 15-Foot Anechoic Wind Tunnel. This paper presents aeroacoustic results at a takeoff/approach condition of Mach 0.20. Laser Doppler Velocimeter results taken in a plane between the two rotors are also included to quantify the interaction flow field. The intention of the forward-swept design is to reduce the magnitude of the forward rotor tip vortex and/or wakes which impinge on the aft rotor, thus lowering the interaction tone levels.

Woodward, Richard P.↗
NASA NTRS2004

Flutter Stability of the Efficient Low Noise Fan Calculated

The TURBO-AE aeroelastic code has been used to verify the flutter stability of the Efficient Low Noise Fan (ELNF), which is also referred to as the trailing-edge blowing fan. The ELNF is a unique technology demonstrator being designed and fabricated at the NASA Glenn Research Center for testing in Glenn's 9-by-15-Foot Low-Speed Wind Tunnel. In the ELNF, air can be blown out of slots near the trailing edges of the fan blades to fill in the wakes downstream of the rotating blades. This filling of the wakes leads to a reduction of the rotor-stator interaction (tone) noise that results from the interaction of wakes with the downstream stators. The ELNF will demonstrate a 1.6-EPNdB1 reduction in tone noise through wake filling, without increasing the broadband noise. Furthermore, the reduced blade row interaction will decrease the possibility of forced response and enable closer spacing of blade rows, thus reducing engine length and weight. During the design of the ELNF, the rotor blades were checked for flutter stability using the detailed aeroelastic analysis capability of the three-dimensional Navier-Stokes TURBOAE code. The aeroelastic calculations were preceded by steady calculations in which the blades were not allowed to vibrate. For each rotational speed, as the back-pressure was increased, the mass flow rate decreased, and the operating point moved along the constant speed characteristic (speed-line) from choke to stall as shown on the fan map. The TURBO-AE aeroelastic analyses were performed separately for the first two vibration modes (bending and torsion) and covered the complete range of interblade phase angles or nodal diameters at which flutter can occur. The results indicated that the ELNF blades would not encounter flutter at takeoff conditions. The calculations were then repeated for a part-speed condition (70-percent rotational speed), and the results again showed no flutter in the operating region. On the fan map (shown), the predicted flutter point at part speed condition was located beyond the stall line, which means that the ELNF will not encounter flutter since it will never operate beyond the stall line. All the calculations done so far have been for the nonblowing case, and selected calculations will be repeated with air blowing from the trailing edge of the fan.

Bakhle, Milind A.↗
NASA NTRS2018

The Revolutionary Vertical Lift Technology (RVLT) Project

The Revolutionary Vertical Lift Technology (RVLT) Project is one of six projects in the Advanced Air Vehicles Program (AAVP) of the NASA Aeronautics Research Mission Directorate. The overarching goal of the RVLT Project is to develop and validate tools, technologies, and concepts to overcome key barriers for vertical lift vehicles. The project vision is to enable the next generation of vertical lift vehicles with aggressive goals for efficiency, noise, and emissions, to expand current capabilities and develop new commercial markets. The RVLT Project invests in technologies that support conventional, non-conventional, and emerging vertical-lift aircraft in the very light to heavy vehicle classes. Research areas include acoustic, aeromechanics, drive systems, engines, icing, hybrid-electric systems, impact dynamics, experimental techniques, computational methods, and conceptual design. The project research is executed at NASA Ames, Glenn, and Langley Research Centers; the research extensively leverages partnerships with the US Army, the Federal Aviation Administration, industry, and academia. The primary facilities used by the project for testing of vertical-lift technologies include the 14- by 22-Ft Wind Tunnel, Icing Research Tunnel, National Full-Scale Aerodynamics Complex, 7- by 10-Ft Wind Tunnel, Rotor Test Cell, Landing and Impact Research facility, Compressor Test Facility, Drive System Test Facilities, Transonic Turbine Blade Cascade Facility, Vertical Motion Simulator, Mobile Acoustic Facility, Exterior Effects Synthesis and Simulation Lab, and the NASA Advanced Supercomputing Complex. To learn more about the RVLT Project, please stop by booth #1004 or visit their website at https://www.nasa.gov/aeroresearch/programs/aavp/rvlt.

NASA↗