Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “power engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

An Investigation in the Ames 40- by 80-Foot Wind Tunnel of a YT-56A Turboprop Engine Incorporating a Decoupler and a Controlled-Feathering Device

An investigation of a decoupler and a controlled-feathering device incorporated with the YT-56A turboprop engine has been made to determine the effectiveness of these devices in reducing the high negative thrust (drag) which accompanies power failure of this type of engine. Power failures were simulated by fuel cut-off, both without either device free to operate, and with each device free to operate singly. The investigation was made through an airspeed range from 50 to 230 mph. It was found that with neither device free to operate, the drag levels realized after power failures at airspeeds above 170 mph would impose vertical tail loads higher than those allowable for the YC-130, the airplane for which the test power package was designed. These levels were reached in approximately one second. The maximum drag realized after power failure was not appreciably altered by the use of the decoupler although the decoupler did put a limit on the duration of the peak drag. The controlled-feathering device maintained a level of essentially zero drag after power failure. The use of the decoupler in the YT-56A engine complicates windmilling air-starting procedures and makes it necessary to place operating restrictions on the engine to assure safe flight at low-power conditions,

Rogallo, Vernon L.↗

Uranium Doped Gallium Nitride Epitaxial Thin Films

Gallium nitride (GaN) is near ubiquitous in modern day technologies, forming the backbone of solid-state lighting and high-power electronics. Engineering the physical properties of GaN has been investigated to some degree by the incorporation or doping of most of the elements of the periodic table, but the actinides remain unexplored. Molecular beam epitaxy is used to demonstrate uranium doping of GaN single crystals. High structural quality of the host matrix is maintained despite partial elemental segregation of the uranium dopant into 1D structures at the levels presented here. Electronic transport measurements reveal relatively high conductivity, which persists down to cryogenic temperature and is characterized by the formation of narrow gaps in the electronic band structures very close to the Fermi level. Photoluminescence measurements reveal that the U-doped GaN exhibits optical behavior similar to that of the GaN substrate. The addition of actinide materials to a non-centrosymmetric, optically active, radiation-hard, and electronically tunable host matrix opens a world of possibilities for investigating and leveraging elements with high electron correlations in the pursuit of novel devices.

36 - MATERIALS SCIENCE↗

Trends in Unconventional Well Development—Methane Emissions Associated with the Use of Dual Fuel and Dedicated Natural Gas Engines

Abstract The process of unconventional natural gas recovery is becoming increasingly popular as the world’s demand for alternative fuels continues to grow. Natural gas has the potential to be a widely used fuel in the near future due to its availability and potential to displace petroleum‐based liquid fuels. As energy companies extract natural gas, current fuels, such as diesel, are consumed in mass quantities for drilling and hydraulic fracturing operations. To save on costs, and in an attempt to reduce emissions, many companies are investing in dual fuel and dedicated natural gas engines to power these operations. This trend results in new sources of methane emissions, which can contribute significantly to global warming. We are aware of the potential impact of these emissions and are conducting research funded by the Department of Energy to assess methane emissions from dual fuel and dedicated natural gas technologies, as industry moves towards more extensive use of natural gas as a fuel for onsite power production.

Johnson, Derek↗

The Multidimensional Character of Nucleosynthesis in Core-Collapse Supernovae

Observations of supernovae and their remnants reveal highly aspherical distributions of the newly-formed elements that are the dying stars’ contributions to the interstellar medium. Modern simulations of the supernova’s neutrino-powered central engine reveal that these inhomogeneities originate in the first seconds of the explosions. Yet, much of our understanding of supernova nucleosynthesis is based on spherically symmetric models of the explosions. Recent simulations, combining high-fidelity treatments of the neutrino field that drives the explosion, the multidimensional fluid flow that taps this energy source, and the thermonuclear kinetics responsible for the composition of the ejecta, are revealing the limitations of our spherically symmetric understanding. Here, we highlight these recent results to presage the changes in our understanding of supernova nucleosynthesis that will result from a full appreciation of the multidimensional character of core-collapse supernovae.

Hix, W Raphael↗

helixCAM: A platform for programmable cellular assembly in bacteria and human cells

Interactions between cells are indispensable for signaling and creating structure. The ability to direct precise cell-cell interactions would be powerful for engineering tissues, understanding signaling pathways, and directing immune cell targeting. In humans, intercellular interactions are mediated by cell adhesion molecules (CAMs). However, endogenous CAMs are natively expressed by many cells and tend to have cross-reactivity, making them unsuitable for programming specific interactions. Here, we showcase “helixCAM,” a platform for engineering synthetic CAMs by presenting coiled-coil peptides on the cell surface. helixCAMs were able to create specific cell-cell interactions and direct patterned aggregate formation in bacteria and human cells. Based on coiled-coil interaction principles, we built a set of rationally designed helixCAM libraries, which led to the discovery of additional high-performance helixCAM pairs. Finally, we applied this helixCAM toolkit for various multicellular engineering applications, such as spherical layering, adherent cell targeting, and surface patterning.

59 BASIC BIOLOGICAL SCIENCES↗

A computationally efficient algorithm for computing convex hull prices

Electricity markets worldwide allow participants to bid non-convex production offers. While non-convex offers can more accurately reflect a resource's capabilities, they create challenges for market clearing processes. For example, system operators may be required to execute side payments to participants whose costs are not covered through energy sales as determined via traditional locational marginal pricing schemes. Convex hull pricing minimizes this and other types of side payments while providing uniform (i.e., locationally and temporally consistent) prices. Computing convex hull prices involves solving either a large-scale linear program or the Lagrangian dual of the corresponding non-convex scheduling problem. Further, the former approach requires explicit descriptions of market participants' convex hulls. While linear programs for computing convex hull prices are large, their structure is naturally decomposable by generators. Here, in this work, we propose and empirically analyze a Benders decomposition approach to computing convex hull prices that leverages recent advances in convex hull formulations for thermal generating units. We demonstrate across a large set of test instances that our decomposition approach only requires modest computational effort, obtaining solutions at least an order of magnitude faster than the equivalent large-scale linear programming approach. Overall, we provide a computationally feasible method for computing convex hull prices for industrial scale market clearing problems, enabling the possibility of practical adoption of this advanced pricing mechanism.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Room-Temperature Methane Oxidation to Formaldehyde Mediated by CoMoO + Gas-Phase Cations

Formaldehyde (HCHO) is a fundamental chemical feedstock with widespread industrial applications. The direct oxidation of methane by oxygen to formaldehyde (CH 4 + 1/2O 2 → H 2 + HCHO) under mild conditions represents an attractive but challenging transformation, as it requires both activation of the inert C–H bonds of CH 4 and suppression of overoxidation to products such as carbon dioxide. In this work, mass spectrometry experiments combined with theoretical calculations reveal that CoMoO + cations can efficiently mediate this transformation at room temperature. The unique electronic structure of CoMoO + facilitates the formation of a crucial CoMoOCH 2 + intermediate during the reaction with CH 4 and prevents methanol formation. In the subsequent oxidation reaction, the Mo atom in CoMoO + serves as the active site for O 2 adsorption, and both Mo and Co atoms act as electron donors to activate O 2 , leading to the formation of the C–O bond in formaldehyde. This work reports the first gas-phase example of achieving conversion of CH 4 to HCHO and its radical derivatives by O 2 at room temperature using heteronuclear non-noble metal cations. Remarkably, the CoMoOCH 2 + cation maintains high reactivity after adsorbing one or two CH 4 molecules. Finally, these findings provide new mechanistic insights into selective methane activation and conversion.

aldehydes↗

A higher-order finite element reactive transport model for unstructured and fractured grids

Abstract This work presents a new reactive transport framework that combines a powerful geochemistry engine with advanced numerical methods for flow and transport in subsurface fractured porous media. Specifically, the PhreeqcRM interface (developed by the USGS) is used to take advantage of a large library of equilibrium and kinetic aqueous and fluid-rock reactions, which has been validated by numerous experiments and benchmark studies. Fluid flow is modeled by the Mixed Hybrid Finite Element (FE) method, which provides smooth velocity fields even in highly heterogenous formations with discrete fractures. A multilinear Discontinuous Galerkin FE method is used to solve the multicomponent transport problem. This method is locally mass conserving and its second order convergence significantly reduces numerical dispersion. In terms of thermodynamics, the aqueous phase is considered as a compressible fluid and its properties are derived from a Cubic Plus Association (CPA) equation of state. The new simulator is validated against several benchmark problems (involving, e.g., Fickian and Nernst-Planck diffusion, isotope fractionation, advection-dispersion transport, and rock-fluid reactions) before demonstrating the expanded capabilities offered by the underlying FE foundation, such as high computational efficiency, parallelizability, low numerical dispersion, unstructured 3D gridding, and discrete fraction modeling.

58 GEOSCIENCES↗

Perovskite-sensitized β-Ga 2 O 3 nanorod arrays for highly selective and sensitive NO 2 detection at high temperature

Amongst various gaseous pollutants, NO 2 is one of the major exhausts originating from fossil fuel and gas combustions in vehicle engines and power plants at high temperature. Under such a scenario, in situ and real-time gas detection and monitoring solutions are largely limited, which hinders the energy-efficient and resource-saving operations of these advanced energy systems. Herein, a new type of perovskite-sensitized β-Ga 2 O 3 nanorod-array has been successfully fabricated to detect NO x at high temperature selectively and sensitively. The demonstrated gas sensors are highly sensitive to NO 2 at 800 °C, with excellent reversible and reproducible response characteristics. Through the surface decoration of perovskite-type La 0.8 Sr 0.2 CoO 3 (LSCO) nanoparticles, the sensitivity of β-Ga 2 O 3 nanorod array gas sensors is enhanced by nearly an order of magnitude, along with much faster response dynamics. A remarkable selectivity toward oxidative gases was also demonstrated with the robust differentiation of NO 2 .

36 MATERIALS SCIENCE↗

Effect of arsenic on the optical properties of GaSb-based type II quantum wells with quaternary GaInAsSb layers

Optical properties of molecular beam epitaxially grown type II “W” shaped GaSb/AlSb/InAs/GaIn(As)Sb/InAs/AlSb/GaSb quantum wells (QWs) designed for the active region of interband cascade lasers have been investigated. Temperature dependence of Fourier-transformed photoluminescence and photoreflectance was employed to probe the effects of addition of arsenic into the original ternary valence band well of GaInSb. It is revealed that adding arsenic provides an additional degree of freedom in terms of band alignment and strain tailoring and allows enhancing the oscillator strength of the active type II transition. On the other hand, however, arsenic incorporation apparently also affects the structural and optical material quality via generating carrier trapping states at the interfaces, which can deteriorate the radiative efficiency. These have been evidenced in several spectroscopic features and are also confirmed by cross-sectional transmission electron microscopy images. While arsenic incorporation into type II QWs is a powerful heterostructure engineering tool for optoelectronic devices, a compromise has to be found between ideal band structure properties and high quality morphological properties.

36 MATERIALS SCIENCE↗

Influence of temporary organic bond nature on the properties of compacts and ceramics

This work contains results of investigation of obtaining high thermally conductive ceramics from commercial powders of aluminum nitride and yttrium oxide by the method of monoaxial compaction of granulate. The principal scheme of preparation is proposed and technological properties of granulate are defined. Compaction conditions for simple items to use as heat removal in microelectronics and power electrical engineering have been established. Investigations of thermophysical properties of obtained ceramics and its structure by the XRD and SEM methods have been carried out. Ceramics with thermal conductivity from 172 to 174 W/m·K has been obtained as result of this work.

36 MATERIALS SCIENCE↗

Renewable Thermal Hybridization Framework for Industrial Process Heat Applications

Solar industrial process heat (SIPH) technologies, such as concentrating solar power collectors, could economically replace the steam or heat needs at many industrial sites by providing high-temperature heat transfer fluids (HTFs) such as pressurized water, synthetic-oil, or direct steam. Renewable thermal energy systems (RTES) could be hybridized with different renewable options e.g., flat plate collectors with parabolic trough collectors, or combined with existing heat supplies (e.g., fossil fuels), to give options for targeted SIPH applications, industrial decarbonization and the reduction of fuel consumption. Hybrid solutions and thermal energy storage will be important for the dispatch of heat at optimal times needed by the demand side of the buildings and industrial applications. At present, there is no integrated modeling tool for hybrid RTES, and this paper highlights the development of a renewable thermal hybridization framework for IPH use that is built from existing tools like System Advisor Model. The long-term vision for the framework (through significant further research) is to develop a coupled hybrid energy generation and cost analysis tool, where the tool could help the user in determining the most suitable and cost-effective technologies for their applications. Ongoing work will look to add costs for RTES options and further refinement on the selection of suitable technologies. This future tool could calculate the levelized cost of heat of various RTES hybrid options, by taking the user's solar resource, fuel costs, industrial heat demand profile, available land, and other factors into account to determine the applicability into their process.

concentrating solar power↗

JET LUMINOSITY FROM NEUTRINO-DOMINATED ACCRETION FLOWS IN GAMMA-RAY BURSTS

A hyperaccretion disk formed around a stellar-mass black hole is a plausible model for the central engine that powers gamma-ray bursts (GRBs). If the central black hole rotates and a poloidal magnetic field threads its horizon, a powerful relativistic jet may be driven by a process resembling the Blandford-Znajek (BZ) mechanism. We estimate the luminosity of such a jet as a function of mass accretion rate and other accretion parameters assuming that the poloidal magnetic field strength is comparable to the inner accretion disk pressure. We show that the jet efficiency attains its maximal value when the accretion flow is cooled via optically thin neutrino emission. The jet luminosity is much larger than the energy deposition through neutrino-antineutrino annihilation ({nu} {nu}-bar {yields}e{sup +}e{sup -}) provided that the black hole is spinning rapidly enough. When the accretion rate onto a rapidly spinning black hole is larger than 0.003-0.01 M{sub Sun} s{sup -1}, the disk becomes optically thin to neutrinos, its pressure increases and the jet luminosity is sufficient to drive a GRB. The transition of the accretion rate above and below this limiting value may cause the large variability observed in GRB.

79 ASTRONOMY AND ASTROPHYSICS↗

Enhancing ZnO nanowire gas sensors using Au/Fe 2 O 3 hybrid nanoparticle decoration

Heterojunctions are an important strategy for designing high performance electrical sensor materials and related devices. Herein, a new type of metal-semiconductor hybrid nanoparticle has been successfully used to remarkably sensitize the surface of ZnO nanowires for detecting NO 2 with high responses over a broad temperature window ranging from room temperature to 600 °C. These hybrid nanoparticles are comprised of iron oxide nanowires with well dispersed single crystalline Au nanoparticles. The hybrid nanoparticle decorated ZnO nanowires have achieved a giant response, as high as 74 500 toward NO 2 gas, about 42 times that of Au decorated ZnO nanowire sensors. This dramatic enhancement may be attributed to the efficient charge transfer across the Au–Fe 2 O 3 Schottky and Fe 2 O 3 –ZnO semiconductor heterojunction interfaces. Due to the incorporation of thermally-stable Fe 2 O 3 nanoparticles as the support of Au nanoparticles, the working temperature of nanowire sensors was successfully extended to higher temperatures, with an increase of 200 °C, from 400 °C to 600 °C. Such a combination of semiconductor heterojunction and semiconductor-metal Schottky contact presents a new strategy for designing high performance electrical sensors with high sensitivity, stability, selectivity, and wide operation temperature window, which are potentially suitable for advanced energy systems such as automotive engines and power plants.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

THE DISCOVERY OF A NEW INSTABILITY IN A HYPERACCRETION FLOW AND ITS IMPLICATION FOR GAMMA-RAY BURSTS

A hyperaccretion flow around a stellar mass black hole is thought to be the most plausible engine that powers gamma-ray bursts (GRBs). The flow efficiently cools via neutrino emission at ∼> 0.003-0.01 M {sub ☉} s{sup –1} (corresponding to a luminosity of ∼10{sup 50} erg s{sup –1}), while neither neutrino nor photon emission is efficient below this rate, so the flow should be advection-dominated. We carefully solve how a transition occurs from the advection-dominated to the neutrino-dominated branches, and find that the slope of the thermal equilibrium curve is negative in the surface density-accretion rate (Σ- M-dot ) plane, a condition for viscous instability, at radii smaller than ∼12 R {sub g} (with R {sub g} being the gravitational radius). We also confirm that the flow is thermally stable. The consequence of this instability is the formation of a clumpy structure in the flow. This is because the larger (respectively smaller) surface density is, the smaller (respectively larger) the mass accretion rate from the region in question becomes, leading to growth of the density contrast. The timescale for clump formation is estimated to be shorter than 0.1 s. The observational implication is discussed in the context of GRBs. We suggest that this might explain the origin of the large variability observed in the prompt emission of GRBs.

79 ASTRONOMY AND ASTROPHYSICS↗

Distributed Ledger Technology for Fault Tolerant Distribution Grid Operations

This paper explores the potential of distributed ledger technology (DLT) to improve fault-tolerant grid operations by leveraging its core features as an immutable, decentralized ledger, a distributed, consensus-based agreement process, and a distributed state-replication engine. Distribution power systems deliver electricity to millions of customers; however, they are susceptible to various threats that can result in customer interruptions. These include faults caused by adverse weather conditions, natural disasters, vegetation growth, equipment failure, and malicious attacks. To minimize the effects of these faults, fault-handling approaches rely on network knowledge to isolate affected areas and reconnect unaffected areas, reducing the number of affected customers while maintaining safety. Here, we present a trusted data-sharing architecture that enables independent, distributed actors to reconstruct the pre-fault system state by enabling distributed resources to make appropriate decisions with limited network/system information. Although the process requires some data sharing between switch-delimited areas, the approach limits the amount of private information shared, preserving customers' privacy and business-sensitive information. We include three use cases that form a foundation for third parties to develop functional solutions that can eventually be deployed in the field. The gross error detection method used within switch-delimited areas can identify sensor errors and accurately detect circuit breaker states. The evaluation of possible reconnection while preserving data ownership resulted in a voltage magnitude difference smaller than 0.001% from the OpenDSS power flow solution that has full system knowledge, which is below the expected power flow tolerance. The approach offers a promising opportunity for improving fault-tolerant distribution grid operations.

24 POWER TRANSMISSION AND DISTRIBUTION↗