Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “power coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Modeling arcjet space thrusters

The UTSI arcjet model is used to compare the performance of a hydrogen and an ammonia arcjet in the same configuration and at the same electrical power. The predicted specific impulse is 50 percent higher for the hydrogen propellant. Numerical studies made of the effect of transport properties on the performance of a hydrogen arcjet indicate that diffusive transport is very significant even in the supersonic part of the flow, and that relatively small changes in transport properties can have a significant effect on performance. These studies also show that nonequilibrium recombination chemistry can have a large effect on the transport coefficients. This leads to the conclusion that finite rate chemical calculations are necessary if accurate arcjet performance is to be calculated.

Rhodes, Robert↗
NASA NTRS1993

Rotor design optimization using a free wake analysis

The aim of this effort was to develop a comprehensive performance optimization capability for tiltrotor and helicopter blades. The analysis incorporates the validated EHPIC (Evaluation of Hover Performance using Influence Coefficients) model of helicopter rotor aerodynamics within a general linear/quadratic programming algorithm that allows optimization using a variety of objective functions involving the performance. The resulting computer code, EHPIC/HERO (HElicopter Rotor Optimization), improves upon several features of the previous EHPIC performance model and allows optimization utilizing a wide spectrum of design variables, including twist, chord, anhedral, and sweep. The new analysis supports optimization of a variety of objective functions, including weighted measures of rotor thrust, power, and propulsive efficiency. The fundamental strength of the approach is that an efficient search for improved versions of the baseline design can be carried out while retaining the demonstrated accuracy inherent in the EHPIC free wake/vortex lattice performance analysis. Sample problems are described that demonstrate the success of this approach for several representative rotor configurations in hover and axial flight. Features that were introduced to convert earlier demonstration versions of this analysis into a generally applicable tool for researchers and designers is also discussed.

Quackenbush, Todd R.↗
NASA NTRS1995

Nearly sonic and transsonic convective motions in the solar atmosphere related to the solar wind origin

MHD equations are considered for the solar atmosphere. 15 different simplest MHD regimes are indicated for the momentum transport equation depending on the mutual binary interplay between 6 possible and locally dominant terms: non-stationarity and inhomogeneity of the flow, gas pressure, magnetic tensions, viscous and gravity forces. These regimes are delimited by five physically independent dimensionless parameters, for example, Strouhal, sonic Mach, alfvenic Mach, Reynolds and Froude numbers or their combinations. Another partially overlapping classification of the simplest regimes may be introduced based on the energy conservation equation. There are also 15 independent binary combinations between nonstationary and inhomogeneous convective terms, dissipative energy sinks and sources (viscous, heat-conductive, Joule and radiative ones) in the energy equation. More complicated regimes are considered with multiple dominated terms. All these MHD regimes play their important role somewhere in the solar atmosphere complicated by the tensor transport coefficients in the magnetically dominated regions of the upper atmosphere. Nearly sonic and transsonic nonstationary convective motions with ascending and descending flows are observed in the solar chromosphere. the transition region and the lower pans of the solar corona together with related horizontal velocity components. This convection represents a kind of the 'cocoonery' manufacturing nonstationary vortices generated here and partially connected to the photosphere and to the solar wind. The solar wind originates from this powerful transsonic muddle in the solar atmosphere as a tiny fraction of the streamlines which are temporarily getting detached from the 'cocoons; and going to the infinity. The topologically complicated instantaneous 'runaway surface' around the Sun, i.e., the surface which separates outgoing to the infinity streams from other finite flows in the solar atmosphere was not described in the literature and needs additional investigation. We conclude that a simple one-connected smooth and quasistationary 'critical surface' which is often supposed to be placed somewhere in the solar corona (say, at 4 solar radii) in reality does not exist. Observational and theoretical arguments favor instead of this a highly structured, disordered, patched and time-dependent sonic transition surface in the solar atmosphere permanently fluctuating at positional dependent heights starting sometimes from photospheric (and maybe subphotospheric) levels and more frequently from the chromosphenc network up to several solar radii in the solar corona.

Veselovsky, I. S.↗
NASA NTRS2017

Grain Size-Dependent Crystal Plasticity Constitutive Model for Polycrystal Materials

A new method to introduce grain size-dependence in classical crystal plasticity constitutive model is developed by considering the resistance to dislocation motion in the grain boundary influence region as equivalent to that of a work hardening. A general framework for the size-dependent constitutive model is derived by implementing this method on a core and mantle model. The work hardening, equivalent to grain boundary effect, is realized by introducing a fictitious, pre-existing, plastic strain grain boundary influence region (mantle) following the principles of classical crystal plasticity. This fictitious plastic strain, in effect, increases the yield strength and decreases the initial hardening coefficient of the grain. With the thickness of grain boundary influence region and the distribution of introduced plastic strain remaining the same, the grain boundary effect increased as the grain size becomes smaller. A simplified model that considers the grain boundary effect on a grain average sense is also developed under this general framework. Implementation of this general framework to the specific cases of crystal plasticity constitutive models is demonstrated by considering the case of power law flow rule and hyperbolic-secant hardening rule. Finally, the grain size-dependent constitutive model is validated by comparing the predicted stress-strain behavior of polycrystal samples with different average grain sizes under uniaxial loading with the experimental results.

Grain Size↗
NASA NTRS1959

A Simple Method for Determining Heat Transfer, Skin Friction, and Boundary-Layer Thickness for Hypersonic Laminar Boundary-Layer Flows in a Pressure Gradient

A procedure based on the method of similar solutions is presented by which the skin friction, heat transfer, and boundary-layer thickness in a laminar hypersonic flow with pressure gradient may be rapidly evaluated if the pressure distribution is known. This solution, which at present is. restricted to power-law variations of pressure with surface distance, is presented for a wide range of exponents in the power law corresponding to both favorable and adverse pressure gradients. This theory has been compared to results from heat-transfer experiments on blunt-nose flat plates and a hemisphere cylinder at free-stream Mach numbers of 4 and 6.8. The flat-plate experiments included tests made at a Mach number of 6.8 over a range of angle of attack of +/- 10 deg. Reasonable agreement of the experimental and theoretical heat-transfer coefficients has been obtained as well as good correlation of the experimental results over the entire range of angle of attack studied. A similar comparison of theory with experiment was not feasible for boundary-layer-thickness data; however, the hypersonic similarity theory was found to account satisfactorily for the variation in boundary-layer thickness due to local pressure distribution for several sets of measurements.

Bertram, Mitchel H.↗
NASA NTRS1998

Emittance Theory for Cylindrical Fiber Selective Emitter

A fibrous rare earth selective emitter is approximated as an infinitely long, cylinder. The spectral emittance, e(sub x), is obtained L- by solving the radiative transfer equations with appropriate boundary conditions and uniform temperature. For optical depth, K(sub R), where alpha(sub lambda), is the extinction coefficient and R is the cylinder radius, greater than 1 the spectral emittance depths, K(sub R) alpha(sub lambda)R, is nearly at its maximum value. There is an optimum cylinder radius, R(sub opt) for maximum emitter efficiency, n(sub E). Values for R(sub opt) are strongly dependent on the number of emission bands of the material. The optimum radius decreases slowly with increasing emitter temperature, while the maximum efficiency and useful radiated power increase rapidly with increasing, temperature.

Chubb, Donald L.↗
NASA NTRS2021

Low Cost Access to Mars Surface using a Small Impact Lander

In order to reduce the cost of landing small payloads on Mars, a new technology is being developed: the Small High Impact Energy Landing Device concept (SHIELD). The purpose of SHIELD is to provide a low-cost option to deliver up to 6 kg of science payload to the surface of Mars. SHIELD could be launched as a hosted payload, rideshare on an EELV secondary payload adapter (ESPA), or launching from a dedicated small launch vehicle using a kick stage. The SHIELD concept can achieve low-cost access to Mars by taking advantage of a low ballistic coefficient design to decelerate safely instead of using the typically required parachutes and/or propulsion to decelerate and stabilize itself during entry, decent, and landing (EDL). Current finite element simulations suggest that SHIELD would experience an impact acceleration pulse ranging from 1000 to 2000 g’s with a duration of 8 milliseconds. The SHIELD concept payload subsystem includes a “ruggedized” small warm electronics box (WEB). The WEB houses the telecommunications, command and data handling, thermal control, electrical power, and payload subsystems while maintaining an internal operating temperature ranging between -20° to 20° C. The system is designed to survive the Martian night by utilizing electric heaters powered with solar cells during the day and secondary batteries. The WEB is designed to be impact resistant capable of surviving an impact acceleration pulse equal to or less than 2000 g’s.

Woolley, Ryan↗
NASA NTRS1975

A momentum analysis of helicopters and autogyros in inclined descent, with comments on operational restrictions

A momentum theory was developed for rotors in descending flight. Comparison with available experimental data indicates that the theory, when properly interpreted, yields the optimum performance of the rotor. Power settling can be explained on the basis of the theory. The reasons and the need for operational restrictions on descending flight are discussed. The maximum autorotative performance of a rotor is determined; the theory shows good agreement with flight measurements in autorotation. Similar equations were developed for a wing; it was shown that the ideal performance of an autorotating rotor is identical to that of a wing of equal aspect ratio. A limiting maximum wing lift coefficient which is confirmed by existing experimental data was obtained.

Heyson, H. H.↗
NASA NTRS1981

Aerodynamic drag reduction tests on a box-shaped vehicle

The intent of the present experiment is to define a near optimum value of drag coefficient for a high volume type of vehicle through the use of a boattail, on a vehicle already having rounded front corners and an underbody seal, or fairing. The results of these tests will constitute a baseline for later follow-on studies to evaluate candidate methods of obtaining afterbody drag coefficients approaching the boattail values, but without resorting to such impractical afterbody extensions. The current modifications to the box-shaped vehicle consisted of a full and truncated boattail in conjunction with the faired and sealed underbody. Drag results from these configurations are compared with corresponding wind tunnel results of a 1/10 scale model. Test velocities ranged up to 96.6 km/h (60 mph) and the corresponding Reynolds numbers ranged up to 1.3 x 10 to the 7th power based on the vehicles length which includes the boattail. A simple coast-down technique was used to define drag.

Peterson, R. L.↗
NASA NTRS2002

Dynamical Studies of the Middle Atmosphere Using High Resolution Doppler Imager Observations

This report summarizes the activities of NASA grant NAG5-11068, "Dynamicai Studies of the Middle Atmosphere Using High Resolution Doppler Imager Observations." The High Resolution Doppler Imager (HRDI) on the Upper Atmosphere Research Satellite (UARS) has been providing direct measurements of the Earth's horizontal wind field in the stratosphere, mesosphere and lower thermosphere. Mesospheric temperatures, ozone, and O((sup 1) D) densities, and stratospheric aerosol extinctions coefficients, are also retrieved. The goal of HRDI is to measure the vector winds in the stratosphere (10-40 km), mesosphere, and lower thermosphere (approximately 50-120 km) during the day, and the lower thermosphere at night (approximately 95 km) to an accuracy of 5 m/s. The horizontal wind vector is measured by observing the Doppler shift of rotational lines of molecular oxygen along two lines of sight. In addition to winds, temperatures and volume emission rates are determined in the mesosphere and lower thermosphere, from which ozone and O((sup 1) D) concentrations can be derived, and aerosol scattering coefficients are determined in the stratosphere. UARS was launched on September 12, 1991, into a 585-km circular orbit inclined 57 degrees to the equator HRDI was activated September 28, 1991 and following a period of checkout and adjustment of the instrument parameters, scientific observations began November 2, 199 1. HRDI operated nearly continuously from launch until April 1995. At that time the UARS solar array drive failed, forcing the instruments to time-share the available power. From July 1995 to July 1996 HRDI operated approximately 50% of the time. At that point, one of the three spacecraft batteries failed and from then until September 1998 the duty cycle was less than 20% per month, At that time it was determined that HRDI could operate during each daytime pass, which increased the daytime duty cycle to close to l00%, while nighttime operations were limited to about a week per month. In the fall of 1999, the second tape recorder failed requiring a real time contact with a TRDSS satellite to retrieve that data. This resulted in about 60% data collection efficiency. Finally, in the summer of 2000, the second star sensor failed requiring the spacecraft attitude to be controlled by a three axis magnetometer and sun sensor. This resulted in a loss of attitude knowledge but operations continue with the anticipation of correcting the attitude. A new method for determining the tide and mean structure from satellite data in conjunction with a new tidal model has been devised. For brevity, it shall be referred to as the TMAT or Tide-Mean Assimilation Technique. Most previous methods of tidal analysis are based on various ways of slicing the data set.

Skinner, Wilbert↗
NASA NTRS2021

Low Cost Access to Mars Surface using a Small Impact Lander

In order to reduce the cost of landing small payloads on Mars, a new technology is being developed: the Small High Impact Energy Landing Device concept (SHIELD). The purpose of SHIELD is to provide a low-cost option to deliver up to 6 kg of science payload to the surface of Mars. SHIELD could be launched as a hosted payload, rideshare on as a secondary payload adapter, or launching from a dedicated small launch vehicle using a kick stage to get to Mars. In order to enable delivery of low cost, SHIELD uses a large diameter deployed drag surface (> 2 m diameter) and low entry mass (< 50 kg) to achieve a very low ballistic coefficient (< 10 kg/m^2): this low ballistic coefficient results in low terminal velocity (< 70 m/sec) without requiring a parachute. Upon impacting the Martian surface at terminal velocity, SHIELD uses a mechanism to decelerate the payload to rest in a robust and predictable manner that limits acceleration of the payload to < 2000 g with a duration less than 8 milliseconds. The SHIELD concept payload subsystem includes a “ruggedized” small warm electronics box (WEB). The WEB houses the telecommunications, command and data handling, thermal control, electrical power, and payload subsystems while maintaining an internal operating temperature ranging between -20° to 20° C. The system is designed to survive the Martian night by utilizing electric heaters powered in a highly insulated box that is powered solar cells and secondary batteries. The WEB is designed to be impact resistant, capable of surviving an impact acceleration pulse equal to or less than 2000 g’s.

Woolley, Ryan↗
NASA NTRS1986

Ignition of metals and alloys in gaseous oxygen by frictional heating

The ignition of metals and alloys have been investigated by rotating the end of a hollow cylinder against an identical stationary cylinder on a common axis (frictional heating) in gaseous oxygen. A ranking criterion that measures the resistance of metals and alloys to ignition is discussed. It consists of the power per unit area required for ignition conveniently expressed as the product of contact pressure P and average linear velocity ALV. Data are presented that demonstrate that materials that are high in nickel and copper require greater P-ALV products for ignition (more resistant to ignition) than materials that are high in iron. Aluminum and titanium alloys are shown to require the lowest P-ALV products for ignition. The effects of varying surface velocity, contact pressure, coefficient of friction, and oxygen pressure on P-ALV products required for ignition are discussed. The results indicate that P-ALV product required for ignition increases as surface velocity increases, as contact pressure decreases, and as the coefficient of friction decreases. Increasing oxygen pressure will cause the P-ALV product required for ignition to decrease at low pressures and increase at high pressures. In some cases, the relative ranking of materials based on P-ALV products will also change as conditions are varied. The data presented in this paper are from a development program to determine the merits of using such a dynamic test method for ranking materials for oxygen service. The results to date have indicated that more testing is required before this method can be made into a standard test. The data presented do show some of the major parameters affecting the ignition of materials when exposed to frictional heating. The repeatability of the data at any set of conditions have not been thoroughly investigated.

Benz, F. J.↗
NASA NTRS1994

Carbon-carbon piston development

A new piston concept, made of carbon-carbon refractory-composite material, has been developed that overcomes a number of the shortcomings of aluminum pistons. Carbon-carbon material, developed in the early 1960's, is lighter in weight than aluminum, has higher strength and stiffness than aluminum and maintains these properties at temperatures over 2500 F. In addition, carbon-carbon material has a low coefficient of thermal expansion and excellent resistance to thermal shock. An effort, called the Advanced Carbon-Carbon Piston Program was started in 1986 to develop and test carbon-carbon pistons for use in spark ignition engines. The carbon-carbon pistons were designed to be replacements for existing aluminum pistons, using standard piston pin assemblies and using standard rings. Carbon-carbon pistons can potentially enable engines to be more reliable, more efficient and have greater power output. By utilizing the unique characteristics of carbon-carbon material a piston can: (1) have greater resistance to structural damage caused by overheating, lean air-fuel mixture conditions and detonation; (2) be designed to be lighter than an aluminum piston thus, reducing the reciprocating mass of an engine, and (3) be operated in a higher combustion temperature environment without failure.

Gorton, Mark P.↗
NASA NTRS1972

The Aladdin experiment. I - Dynamics.

A coordinated rocket experiment was carried out on Nov. 20, 1970 at Eglin AFB, Fla. (30 deg N) to determine atmospheric layering and density distributions of ions and neutrals. The program measured vertical profiles between 70 and 150 km altitude of total neutrals, ions and electrons, individual species, temperature, density, diffusion coefficients, horizontal winds, and turbulent structure. A dynamic computer code model using these parameters was compared with the observed profiles. Wind fields were measured from seven chemical trails, separated up to 60 km horizontally and 600 sec in time. Kinetic temperatures were measured from fluorescence of chemically-released AlO, ranging from 440 to 680 K between 126 and 161 km. Densities derived from diffusion of the AlO ranged from 10 to 5 times 10 to the -12th power per cu cm between 126 and 139 km. A rocket-borne pitot probe showed wavelike density deviations from current standard atmosphere models, amounting to -25% at 80 and 110 km and to +25% at 100 and 125 km. The derived temperature profile from the pitot probe showed a double minimum at 74 and 102 km.

Rosenberg, N. W.↗
NASA NTRS1991

An integrated aerodynamic/propulsion study for generic aero-space planes based on waverider concepts

Research efforts related to the development of a unified aerospace plane analysis based on waverider technology are summarized. Viscous effects on the forebodies of cone-derived waverider configurations were studied. A simple means for determining the average skin friction coefficient of laminar boundary layers was established. This was incorporated into a computer program that provides lift and drag coefficients and lift/drag ratio for on-design waveriders when the temperature and Reynolds number based on length are specified. An effort was made to carry out parabolized Navier-Stokes (PNS) calculations for cone-derived waveriders. When the viscous terms were turned off (in the Euler mode) computations for elliptic cone-derived waveriders could be carried out for a wide range of on-design and off-design situations. Work related to waveriders derived from power law shocks is described in some detail.

Emanuel, G.↗
NASA NTRS1992

Modelling a single phase voltage controlled rectifier using Laplace transforms

The development of a 20 kHz, AC power system by NASA for large space projects has spurred a need to develop models for the equipment which will be used on these single phase systems. To date, models for the AC source (i.e., inverters) have been developed. It is the intent of this paper to develop a method to model the single phase voltage controlled rectifiers which will be attached to the AC power grid as an interface for connected loads. A modified version of EPRI's HARMFLO program is used as the shell for these models. The results obtained from the model developed in this paper are quite adequate for the analysis of problems such as voltage resonance. The unique technique presented in this paper uses the Laplace transforms to determine the harmonic content of the load current of the rectifier rather than a curve fitting technique. Laplace transforms yield the coefficient of the differential equations which model the line current to the rectifier directly.

Kraft, L. Alan↗
NASA NTRS2006

Using CO2:CO Correlations to Improve Inverse Analyses of Carbon Fluxes

Observed correlations between atmospheric concentrations of CO2 and CO represent potentially powerful information for improving CO2 surface flux estimates through coupled CO2-CO inverse analyses. We explore the value of these correlations in improving estimates of regional CO2 fluxes in east Asia by using aircraft observations of CO2 and CO from the TRACE-P campaign over the NW Pacific in March 2001. Our inverse model uses regional CO2 and CO surface fluxes as the state vector, separating biospheric and combustion contributions to CO2. CO2-CO error correlation coefficients are included in the inversion as off-diagonal entries in the a priori and observation error covariance matrices. We derive error correlations in a priori combustion source estimates of CO2 and CO by propagating error estimates of fuel consumption rates and emission factors. However, we find that these correlations are weak because CO source uncertainties are mostly determined by emission factors. Observed correlations between atmospheric CO2 and CO concentrations imply corresponding error correlations in the chemical transport model used as the forward model for the inversion. These error correlations in excess of 0.7, as derived from the TRACE-P data, enable a coupled CO2-CO inversion to achieve significant improvement over a CO2-only inversion for quantifying regional fluxes of CO2.

Palmer, Paul I.↗
NASA NTRS1989

Comparison of laser models

Progress on the comparison of laser models is reported. Equations for an oscillatory model and a nonoscillatory model for the simulation of iodine laser operation are solved. Reaction rate coefficients used in both models are listed. Currently there are four models for the simulation of iodine laser operation are solved. Reaction rate coefficients used in both models are listed. Currently there are four models for the simulation of an iodine laser. They are: (1) a time dependent model; (2) a quasi-steady state model; (3) a noncompressible model; and (4) a compressible flow laser model. Current research is being directed toward: (1) parameter studies using the compressible flow laser model; (2) development of a two-pass amplifier model; and (3) solving a system of equations describing operation of the high powered iodine MOPA (master oscillator power amplifier).

Heinbockel, John H.↗