Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “phase control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Testing the DAE LLRF system with a PIP-II SSR2 Cavity

The PIP-II linac is an international collaboration project with in kind contributions of key subsystems from multiple countries including India (DAE). In the research and development phase of the project, the LLRF and resonance control systems were jointly developed by BARC and Fermilab and were delivered to Fermilab for testing and validation. Initial testing of the LLRF system was carried out using Fermilabs analog cavity emulator. Following successful emulator testing, the LLRF system was deployed at STC on a PIP-II 325 MHz SSR2 cavity. The cavity was operated in both SEL and GDR modes at a gradient of 5 MV/m. The results of the testing are presented here.

Nasery, Radhika [Bhabha Atomic Res. Ctr.]↗
DOE OSTI2023

Energy-Efficient Driving in Connected Corridors via Minimum Principle Control: Vehicle-in-the-Loop Experimental Verification in Mixed Fleets

Connected and automated vehicles (CAVs) can plan and actuate control that explicitly considers performance, system safety, and actuation constraints in a manner more efficient than their human-driven counterparts. In particular, eco-driving is enabled through connected exchange of information from signalized corridors that share their upcoming signal phase and timing (SPaT). This is accomplished in the proposed control approach, which follows first principles to plan a free-flow acceleration-optimal trajectory through green traffic light intervals by Pontryagin's Minimum Principle in a feedback manner. Urban conditions are then imposed from exogeneous traffic comprised of a mixture of human-driven vehicles (HVs) - as well as other CAVs. As such, safe disturbance compensation is achieved by implementing a model predictive controller (MPC) to anticipate and avoid collisions by issuing braking commands as necessary. The control strategy is experimentally vetted through vehicle-in-the-loop (VIL) of a prototype CAV that is embedded into a virtual traffic corridor realized through microsimulation. Up to 36% fuel savings are measured with the proposed control approach over a human-modelled driver, and it was found connectivity in the automation approach improved fuel economy by up to 26% over automation without. Additionally, the passive energy benefits realizable for human drivers when driving behind downstream CAVs are measured, showing up to 22% fuel savings in a HV when driving behind a small penetration of connectivity-enabled automated vehicles.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Melting and solidification dynamics during laser melting of reaction-based metal matrix composites uncovered by in-situ synchrotron X-ray diffraction

Laser additive manufacturing (AM) of reaction-based metal matrix composites (MMCs) involves highly complex and non-equilibrium material transformation behavior, including melting, dissolution, precipitation, and solidification. Yet, the dynamics and interplay of these phase transformation processes remain poorly understood, posing substantial challenges in identifying the microstructure formation mechanism, and predicting and controlling the microstructure in the printed parts. Here, in this study, we performed the in-situ X-ray diffraction experiment to characterize the phase evolution dynamics of the 316L + 10 vol.%TiC system during laser melting, which provides direct and quantitative insights of the complex phase reaction and evolution dynamics under rapid heating and cooling conditions relevant to additive manufacturing of reaction-based MMCs. Further in-depth thermodynamic and kinetic calculations revealed that most of the phase evolution behavior observed in the in-situ X-ray diffraction experiment cannot be solely explained by widely used equilibrium thermodynamic models, and diffusion-controlled nonequilibrium dissolution and precipitation kinetics must be considered to elucidate the complex phase evolution behavior, including incomplete TiC dissolution, and three-step TiC precipitation. The three distinct types of precipitates generate unique hierarchical TiC micro- and nanostructures, which enhances the yield strength from 513 MPa to 877 MPa by 71 %, tensile strength from 628 MPa to 1054 MPa by 68 %, and Young's modulus from 193 GPa to 221 GPa by 14 %. The findings of our research provide the knowledge foundation for the design of unique microstructures and advanced MMC materials through laser AM.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Notes on Complex (Including Phase-Only) Tapered Active Array Antenna Performance

Modern Active Electronically Steerable Array (AESA) antennas offer substantial control over transmit and receive antenna beam forming, including via elemental weighting to achieve a desired tapered aperture. Elemental taper weighting may generally be complex, with both amplitude and phase components. This includes phase-only tapers. However, array tapers may also have the adverse side effect of diminishing transmit and/or receive effectiveness. This is readily calculated, and must be ...

Doerry, Armin Walter [Sandia National Laboratories↗
DOE OSTI2021

Real-Time Longitudinal Profile Measurement of Operational H⁻ Beam at the SNS Linac Using a Laser Comb

We demonstrate a novel technique to measure the longitudinal profile of an operational hydrogen ion (H⁻) beam in a non intrusive, real-time fashion. The measurement is conducted based on the photo-ionization of the ion beam with a phase modulated laser comb pico-second laser pulses with controllable temporal structure. The measurement technique has been applied to a 1-GeV, 1.4-MW H⁻ beam at the Spallation Neutron Source (SNS) high energy beam transport (HEBT). A stroboscopic photo-graph of H⁻ beamμbunch can be obtained by using a phase modulated laser comb. The entire measurement takes only 700 us.

Liu, Yun↗
DOE OSTI2020

Probing light-driven quantum materials with ultrafast resonant inelastic X-ray scattering

Abstract Ultrafast optical pulses are an increasingly important tool for controlling quantum materials and triggering novel photo-induced phase transitions. Understanding these dynamic phenomena requires a probe sensitive to spin, charge, and orbital degrees of freedom. Time-resolved resonant inelastic X-ray scattering (trRIXS) is an emerging spectroscopic method, which responds to this need by providing unprecedented access to the finite-momentum fluctuation spectrum of photoexcited solids. In this Perspective, we briefly review state-of-the-art trRIXS experiments on condensed matter systems, as well as recent theoretical advances. We then describe future research opportunities in the context of light control of quantum matter.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Proof-of-Concept for Sensor Modeling in MOOSE for the Design of Autonomous Nuclear Reactor Control

Autonomous operation is essential for the deployment of microreactors and fission batteries, both in terrestrial and space applications. For this reason, recent studies have investigated autonomous control by using adaptive model predictive control and multi-objective optimization for heat pipe–cooled microreactors under normal and heat pipe failure conditions. However, prototypes of microreactors and fission batteries do not exist yet, and even the design space has not been narrowed down conclusively, making the instrumentation and control system design difficult. For this reason, there is a need for flexible computational capabilities to create a numerical stand-in of potential microreactor and fission battery designs. The latter can be used to design and test control strategies to support autonomous operations. In this poster, we describe the initial implementation of a pluggable sensor system for the easy implementation of realistic sensor models in the multiphysics object-oriented simulation environment (MOOSE) framework. This new capability will enable MOOSE users to create a numerical stand-in of microreactors and fission batteries, ultimately allowing them to easily test new control algorithms, and instrumentation strategies for advanced systems in the design phase.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Engineering phase-frustration-induced flat bands in an aza-triangulene covalent kagome lattice

π-Conjugated covalent organic frameworks provide a versatile molecular scaffold for the realization of designer quantum nanomaterials. Strong electron–electron correlation within these artificial lattices can give rise to exotic phases of matter. Their experimental realization, however, requires precise control over orbital symmetry, charge localization and band dispersion, all arising from the effective hybridization between molecular linkers and nodes. Here we present a modular strategy for constructing diatomic kagome lattices from aza-[3]triangulene nodes, in which a D 3h -symmetric ground state is stabilized through resonance contributions from a cumulenic linker. First-principles density functional theory and scanning tunnelling spectroscopy reveal that the hybridization of a sixfold-degenerate set of edge-localized Wannier functions in the unit cell gives rise to orbital-phase-frustration-induced non-trivial flat bands. These results establish a general design principle for engineering orbital interactions in organic lattices and open a pathway towards programmable covalent-organic-framework-based quantum materials with correlated electronic ground states.

conjugated polymers↗
DOE OSTI2024

Materials Characterization: A Primer for Solid Phase Processing Applications

The Pacific Northwest National Laboratory (PNNL) undertook the Materials Characterization, Prediction, and Control (MCPC) Laboratory Directed Research and Development (LDRD) Project to advance understanding of nuclear material processing and enable multifold acceleration in the development and qualification of new material systems produced via advanced manufacturing methods, such as solid phase processing, for use in national security and advanced energy applications (Smith 2021). As a two-year LDRD investment requiring focused research, the MCPC project applied only a subset of the wide range of available destructive and nondestructive characterization methods to provide data to the predictive modeling and data analytics tasks. The purpose of this report is to review a wide range of destructive and nondestructive characterization methods that are relevant in solid-phase processing (SPP) applications, but not necessarily applied in the MCPC Project as a guide to the planning of characterization activities in future research. Particular attention is given to measured characteristics that can correlate to other material characteristics, with a particular interest in nondestructive evaluation (NDE) that can be applied to samples obtained in the MCPC Project. Destructive examinations include tensile tests, optical and electron microscopy, micro-hardness, and residual stress tests. NDE tests include surface visual inspection, eddy current examination for cracks, 4-point potential drop, ultrasound, x-ray, and computed tomography.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Cosmic-ray transport in inhomogeneous media

A theory of cosmic-ray transport in multiphase diffusive media is developed, with the specific application to cases in which the cosmic-ray diffusion coefficient has large spatial fluctuations that may be inherently multiscale. We demonstrate that the resulting transport of cosmic rays is diffusive in the long-time limit, with an average diffusion coefficient equal to the harmonic mean of the spatially varying diffusion coefficient. Thus, cosmic-ray transport is dominated by areas of low diffusion even if these areas occupy a relatively small, but not infinitesimal, fraction of the volume. On intermediate time-scales, the cosmic rays experience transient effective subdiffusion, as a result of low-diffusion regions interrupting long flights through high-diffusion regions. In the simplified case of a two-phase medium, we show that the extent and extremity of the subdiffusivity of cosmic-ray transport is controlled by the spectral exponent of the distribution of patch sizes of each of the phases. We finally show that, despite strongly influencing the confinement times, the multiphase medium is only capable of altering the energy dependence of cosmic-ray transport when there is a moderate (but not excessive) level of perpendicular diffusion across magnetic-field lines.

Astronomy and Astrophysics↗
DOE OSTI2021

Binary and Ternary Colloidal Cu–Sn–Te Nanocrystals for Thermoelectric Thin Films

Recent advances in copper chalcogenide-based nanocrystals (NCs), copper sulfide, and copper selenide derived nanostructures, have drawn considerable attention. However, reports of crystal phase and shape engineering of binary or ternary copper telluride NCs remain rare. Here, a colloidal hot-injection approach for producing binary copper/tin telluride, and ternary copper tin telluride NCs with controllable compositions, crystal structures, and morphologies is reported. Here, the crystal phase and growth behavior of these tellurides are systematically studied from both experimental and theoretical perspectives.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Local Strain and Polarization Mapping in Ferrielectric Materials

CuInP 2 S 6 (CIPS) is a van der Waals material that has attracted attention because of its unusual properties. Recently, a combination of density functional theory (DFT) calculations and piezoresponse force microscopy (PFM) showed that CIPS is a uniaxial quadruple-well ferrielectric featuring two polar phases and a total of four polarization states that can be controlled by external strain. In this study, we combine DFT and PFM to investigate the stress-dependent piezoelectric properties of CIPS, which have so far remained unexplored. The two different polarization phases are predicted to differ in their mechanical properties and the stress sensitivity of their piezoelectric constants. This knowledge is applied to the interpretation of ferroelectric domain images, which enables investigation of local strain and stress distributions. The interplay of theory and experiment produces polarization maps and layer spacings which we compare to macroscopic X-ray measurements. We found that the sample contains only the low-polarization phase and that domains of one polarization orientation are strained, whereas domains of the opposite polarization direction are fully relaxed. The described nanoscale imaging methodology is applicable to any material for which the relationship between electromechanical and mechanical characteristics is known, providing insight on structural, mechanical, and electromechanical properties down to ~10 nm length scales.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Bioinspired mineralizing microenvironments generated by liquid-liquid phase coexistence

Biominerals such as bones, teeth and shells exhibit improved mechanical properties and intricate morphologies not seen in nonbiologically-produced minerals of ostensibly the same composition. These remarkable properties of biogenic minerals are thought to arise due to precise local control over the mineral deposition process, including organic and inorganic inclusions. Understanding how Biology controls the local reaction environment during formation of these materials to control their composition, structure, and properties is a grand challenge that promises to enable new routes to high-performance materials. This project developed multi-compartment bioinspired microreactors as artificial mineralizing vesicles, and used them to understand and control formation of inorganic/organic composite solid materials. A major emphasis was on developing all-aqueous emulsions in which each droplet was a structured microreactor with two or more adjacent phases. This approach provided local control over reaction environment including availability of inclusions such as polypeptides and metal ions, while being sufficiently simple to produce large populations of essentially identical multiphase reactor droplets simultaneously within a batch. Organic/inorganic composite materials could be produced with very high organic content that stabilized the inorganic portions as amorphous materials (e.g., amorphous calcium carbonate) by preventing the typical conversion to more thermodynamically crystalline forms (e.g., calcite). These stabilized amorphous composites could be stored indefinitely and converted to crystalline forms later by removal of the organic inclusions via, for example, heating. Compositional gradients in the organic and inorganic components were embedded during synthesis due to the evolution of the reaction microenvironment, and despite the complexity of this process it occurred similarly across the population of reactive droplets and was hence encoded into the population of resulting composite particles. The approach developed here allows pre-structuring of reactive microenvironments to control the spatiotemporal reaction environment, which is an important step towards rational design and on-demand production of complex functional materials with desired composition, optical properties, and mechanical response.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Validation and Verification for INL Modelica-based TEDS models Via Experimental Results

This report provides an overview on the verification and validation (V&V) of the Thermal Energy Distribution System (TEDS) model developed in the Modelica process modeling ecosystem using experimental data. Model development has led to the creation of a dynamic process model of the experimental TEDS facility housed within the Energy Systems Laboratory (ESL) at Idaho National Laboratory (INL). The model was then used during the preconstruction phase of the experimental effort to inform experimental design (e.g., insulation requirements, bypass line placement, expected performance of components) and to test innovative control schemes prior to the initial operation. The TEDS model developed in Modelica includes the primary components of the TEDS experimental unit: a 200kW Chromalox heater; a single-tank packed-bed thermal energy storage system filled with 0.125-inch alumina (Al2O3) beads; an ethylene-glycol-to-Therminol-66 heat exchanger; system piping; five control valves; and all associated temperature, pressure, and volumetric flow sensors. Using the Institute of Electrical and Electronics Engineers (IEEE) V&V methodologies, considered the gold standard in the engineering field, the model was verified using a combination of static analysis, spatial convergence, and regression tests. Then using dynamic time warping (DTW) initial runs to validate and tune the TEDS model versus the experiment were conducted. This tuning method was accomplished using the INL Risk Analysis Virtual ENvironment (RAVEN) software package. Tuning is required to account for physical phenomena that are less understood within the empirical heat transfer correlations. Through the commencement of this work, a systems-level model of TEDS with associated control systems, sensors, piping diameters, and component capabilities has been created. This model was utilized in the pre-experimental phase to inform system design, insulation thicknesses, and potential control schemes to operate the system effectively and safely. Then, initial experimental startup and operational data were used to demonstrate the validation and tuning methodology. This process demonstrates the classical two-step approach of a model informing experimental design followed by the experiment validation and tuning the model.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Development of a Practical Secondary Control for Hardware Microgrids

Practical, vendor-agnostic interoperability guidelines for the secondary control architecture of microgrids (MGs) with multiple grid-forming (GFM) inverter-based resources (IBRs) have not yet been developed. Therefore, this paper proposes a generic and vendor-agnostic secondary control architecture that operates with all GFM IBRs and synchronous generators. This secondary control does not require the use of additional measurement devices in the MG and utilizes the inherent communication systems of the GFM units, such as Modbus TCP/IP. The practical challenges of Modbus registers, such as packet loss and quantization error, and their detrimental impacts on secondary control actions are investigated. The proposed three-stage modification for any secondary control architecture to mitigate these impacts includes: 1) averaging the data read, 2) situational event-triggering of the controller, and 3) finite iteration of the controlling action. The proposed method is validated using a three-phase electric power, 480 V, 60 Hz, 500 kVA laboratory hardware microgrid with commercial two GFM IBRs and one diesel generator. The experimental results corroborates the fact the proposed modification in the secondary control architecture is advantageous for practical usage under erroneous measurements.

grid-forming inverter↗
DOE OSTI2023

Direct Mechanochemical Synthesis, Phase Stability, and Electrochemical Performance of α-NaFeO 2

To better understand polymorph control in transition metal oxides, the mechanochemical synthesis of NaFeO 2 was explored. In this paper, we report the direct synthesis of α-NaFeO 2 through a mechanochemical process. By milling Na 2 O 2 and γ-Fe 2 O 3 for 5 h, α-NaFeO 2 was prepared without high-temperature annealing needed in other synthesis methods. While investigating the mechanochemical synthesis, it was observed that changing the starting precursors and mass of precursors affects the resulting NaFeO 2 structure. Density functional theory calculations on the phase stability of NaFeO 2 phases show that the α phase is stabilized over the β phase in oxidizing environments, which is provided by the oxygen-rich reaction between Na 2 O 2 and Fe 2 O 3 . This provides a possible route to understanding polymorph control in NaFeO 2 . Annealing the as-milled α-NaFeO 2 at 700 °C has resulted in increased crystallinity and structural changes that improved electrochemical performance in terms of capacity over the as-milled sample.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Evolution of the ATLAS TDAQ online software framework towards Phase-II upgrade: Use of Kubernetes as an orchestrator of the ATLAS Event Filter computing farm

The ATLAS experiment at the LHC at CERN continuously evolves its TDAQ system to meet the challenges of new physics goals and technological advancements. As ATLAS prepares for the Phase-II Run 4 of the LHC, significant enhancements in the TDAQ Controls and Configuration (TDAQ-CC) tools have been designed to ensure efficient data collection, processing, and management. This abstract presents the evolution of ATLAS TDAQ-CC system leading up to Phase-II Run 4. As part of the evolution towards Phase-II, Kubernetes has been chosen to orchestrate the Event Filter (EF) farm. By leveraging Kubernetes, ATLAS can dynamically allocate computing resources, scale processing capacity in response to changing data taking conditions and ensure high availability of data processing services. The integration of the Kubernetes with the TDAQ Run Control framework enables perfect synchronisation between the experiment’s data acquisition components and the computing infrastructure. We will discuss the architectural considerations and implementation challenges involved in Kubernetes integration with the ATLAS TDAQ-CC system. We will highlight the benefits of using Kubernetes as an EF farm orchestrator, including improved resource utilization, enhanced fault tolerance, and simplified deployment and management of data processing workflows. In addition, we will report on the extensive testing of Kubernetes that was conducted using a farm of 2500 servers within the experiment data taking environment, demonstrating its scalability and robustness in handling the demands of the ATLAS TDAQ system for Phase-II. The adoption of Kubernetes represents a significant step forward in the evolution of ATLAS TDAQ-CC system, aligning with industry best practices in container orchestration.

Corso Radu, Alina [Univ. of California, Irvine, CA↗
DOE OSTI2020

Development of the INL Thermal Energy Distribution System (TEDS) in the Modelica Eco-System for Validation and Verification

This report provides an overview on the development of the Thermal Energy Distribution System (TEDS) in the Modelica process model eco-system at Idaho National Laboratory as part of the integrated energy system initiative. Model development has led to the creation of a dynamic process model of the experimental TEDS facility housed within the Engineering Science Laboratory (ESL) at INL. The model was then used during the pre-construction phase of the experimental effort to inform experimental design (insulation requirements, bypass line placement, expected performance of components) and to test innovative control schemes prior to the initial operation. The TEDS model developed in Modelica includes the primary components of the TEDS experimental unit including: a 200kW Chromalox heater, a single-tank packed bed thermal energy storage system filled with 0.125 inch Alumina (Al 2 O 3 ), an ethylene-glycol to Therminol-66 heat exchanger, system piping, six control valves, and all associated temperature, pressure, and mass flow sensors. The model does not include nitrogen fill gas tanks, or associated overfill tanks, as these are not part of standard system control. Two simulation sets were run. The first is a five-hour test that operates as a shakedown test for the facility. This simulation puts the facility through all five potential operating modes and showcases the ability of valving, control sensors, and component controllers to meet the system demands. The second case imposes a typical summer day demand on the system from a region with mixed commercial and residential electrical needs where the generator alone cannot meet peak demand but instead requires the thermal storage unit to act as a peaking unit. Over the course of the fifteen-hour discharge cycle heat losses account for a heat loss of approximately 15°C in outlet temperature. Such heat losses would lead to a decrease in overall system efficiency and may lead to additional design changes for such designs in the future that may include a topping heater. Through commencement of this work, a systems level model of TEDS with associated control systems, sensors, piping diameters, and component capabilities has been created. This model has been utilized in the pre-experimental phase to inform system design, insulation thicknesses, and potential control schemes to operate the system effectively and safely. Once TEDS begins operation, this model will be refined, tuned, and used for validation and verification purposes.

24 POWER TRANSMISSION AND DISTRIBUTION↗