Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “panel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Development of lightweight graphite/polyimide sandwich panels.

Lightweight graphite/polyimide composite honeycomb core and sandwich panels were fabricated and tested. Honeycomb cores of 1/4-in. and 3/8-in. cell sizes of hexagonal configuration were produced from thin plus or minus 45 deg cross plied sheets of prepreg producing core weights between 1.8 and 3.6 lb/cu ft. Thin gauge prepreg using Hercules graphite tow and Monsanto Skybond 710 polyimide resin were manufactured to produce cured ply thicknesses of 0.001 to 0.002 in. Graphite core properties measured at temperatures from -150 to 600 F are reported. Core properties which are superior to available materials were obtained. Sandwich panels weighing less than 0.5 lb/sq ft were designed and fabricated which meet the support structure loads for the shuttle orbiter thermal protection system.

Poesch, J. G.↗

Hybrid TE panel test results.

Test results are presented for a nine couple (3 x 3 array) thermoelectric panel of hybrid thermocouples. In the hybrid couple, a hollow cylinder of p-type Si-Ge is used to encapsulate a segmented PbTe/Si-Ge n-leg. The hybrid couple is predicted to offer a 10 to 15% improvement in performance relative to all Si-Ge couples. The efficiency, output power, and internal resistance of the panel, as well as the resistances of the individual hybrid couples, are presented as a function of test time covering a period of more than 2600 hours. Initial test results indicated hybrid couple performance consistent with design predictions. However, the 10 to 15% improvement over all-Si-Ge couples demonstrated initially by the hybrid couple was offset by the high resistance that developed following a thermal cycle due to heater failure after 600 hours of testing.

Bifano, W. J.↗

Advanced beaded and tubular structural panels.

A review is presented of an NASA program to develop light-weight beaded and tubular structural panels which can be applied where beaded external surfaces are acceptable aerodynamically or where primary structure is protected by heat shields. The design shapes were obtained with an optimization computer code which iterates geometric parameters to satisfy strength, stability and weight constraints. Methods of fabricating these new configurations are discussed. Nondestructive testing produced extensive combined compression, shear and bending test data on local buckling specimens and large panels. The optimized design concepts offer 25 to 40% weight savings compared to conventional stiffened sheet construction.

Musgrove, M. D.↗

Generalized random forces for rectangular panels.

Generalized random forces for rectangular panels under subsonic and supersonic boundary-layer turbulence are studied in time domain by a Monte Carlo approach. Panels with simple, fixed, elastic-free, and periodic elastic boundary conditions are considered. The nature of probability structure, peak distribution, threshold crossing, and cross spectral density is investigated.

Vaicaitis, R.↗

Large amplitude flutter of a low aspect ratio panel at low supersonic speeds comparison of theory and experiment

Flutter boundaries, as well as flutter limit cycle amplitudes, frequencies and stresses were computed for a panel of length-width ratio 4.48 exposed to applied in-plane and transverse loads. The Mach number range was 1.1 to 1.4. The method used involved direct numerical integration of modal equations of motion derived from the nonlinear plate equations of von Karman, coupled with linearized potential flow aerodynamic theory. The flutter boundaries agreed reasonably well with experiment, except when the in-plane loading approached the buckling load. Structural damping had to be introduced, to produce frequencies comparable to the experimental values. Attempts to compute panel deflections or stress at a given point met with limited success. There is some evidence, however, that deflection and stress maxima can be estimated with somewhat greater accuracy.

Ventres, C. S.↗

Techniques for aerothermal tests of large, flightweight thermal protection panels in a Mach 7 wind tunnel

Thermal performance and structural integrity are experimentally evaluated in the Langley 8-ft high temperature structures tunnel, which uses a combustion products test medium to provide realistic combinations of aerodynamic heating and loading. Recently developed techniques provide independent control of rate and magnitude of surface heating and differential pressure, protection against adverse acoustics buffeting during facility starting and stopping, programed radiant heating before exposing test panels to the high energy stream, and infrared radiometry for detailed surface temperatures. These techniques were verified repeatedly by return of useful data on metallic and nonmetallic panel concepts of reusable surface insulation.

Deveikis, W. D.↗

Nonlinear panel response by a Monte Carlo approach

The vibration of clamped and simply supported elastic panels due to subsonic and supersonic turbulent boundary-layer flows is investigated by a Monte Carlo technique. The resulting generalized random forces are simulated numerically from boundary-layer turbulence spectra, and the response analysis is performed in the time domain. The mutual interaction between panel motion and external and/or internal airflow is included. Response studies are performed with respect to rms response, probability structure, peak distribution, threshold crossing and spectral density. The effect on the response statistics of in-plane loading, static pressure differential, and cavity pressure is investigated.

Vaicaitis, R.↗

Advanced beaded and tubular structural panels

A program to develop lightweight beaded and tubular structural panels is described. Applications include external surfaces, where aerodynamically acceptable, and primary structure protected by heat shields. The design configurations were optimized and selected with a computer code which iterates geometric parameters to satisfy strength, stability, and weight constraints. Methods of fabricating these configurations are discussed. Nondestructive testing produced extensive combined compression, shear, and bending test data on local buckling specimens and large panels. The optimized design concepts offer 25 to 30% weight savings compared to conventional stiffened sheet construction.

Musgrove, M. D.↗

Advanced panel-type influence coefficient methods applied to subsonic flows

An advanced technique for solving the linear integral equations of three-dimensional subsonic potential flows (steady, inviscid, irrotational and incompressible) about arbitrary configurations is presented. It involves assembling select, logically consistent networks whose construction comprises four tasks, which are described in detail: surface geometry definition; singularity strength definition; control point and boundary condition specification; and calculation of induced potential or velocity. The technique is applied to seven wing examples approached by four network types: source/analysis, doublet/analysis, source/design, and doublet/design. The results demonstrate the forgiveness of the model to irregular paneling and the practicality of combined analysis/design boundary conditions. The appearance of doublet strength mismatch is a valuable indicator of locally inadequate paneling.

Johnson, F. T.↗

Panel flutter optimization by gradient projection

A gradient projection optimal control algorithm incorporating conjugate gradient directions of search is described and applied to several minimum weight panel design problems subject to a flutter speed constraint. New numerical solutions are obtained for both simply-supported and clamped homogeneous panels of infinite span for various levels of inplane loading and minimum thickness. The minimum thickness inequality constraint is enforced by a simple transformation of variables.

Pierson, B. L.↗

Age-forming aluminum panels

Contoured-stiffened 63 by 337 inch 2124 aluminum alloy panels are machined in-the-flat to make integral, tapered T-capped stringers, parallel with longitudinal centerline. Aging fixture, which includes net contour formers made from lofted contour templates, has eggcrate-like structure for use in forming and checking panels.

Baxter, G. I.↗

Modular multipurpose panel support

Inexpensive set of modular semirigid box structures serve as multipurpose support for thin panels. Fixture holds several different, interchangeable, two-part, adjustable, contour-board subassemblies. Combining modules allows for accommodation to any length skin or panel.

Daun, M. R.↗

Multipurpose panel, phase 1, study report

The feasibility of a multipurpose panel which provides a programmable electronic display for changeable panel nomenclature, multiplexes similar indicator display signals to the signal display, and demultiplexes command signals is examined. Topics discussed include: electronic display technology, miniaturized electronic and memory devices, and data management systems which employ digital address and multiplexing.

Parkin, W.↗

SMS crew station (C and D panels and forward structures). CEI part 1: Detail specification, type 1 data

Established are the requirements for performance, design, test and qualification of one type of equipment identified as SMS C&D panels and forward structures. This CEI is used to provide all hardware and wiring necessary for the C&D panels to be properly interfaced with the computer complex/signal conversion equipment (SCE), crew station, and software requirements as defined in other CEI specifications.

Source record↗

Development of lightweight fire retardant, low-smoke, high-strength, thermally stable aircraft floor paneling

Fire resistance mechanical property tests were conducted on sandwich configurations composed of resin-fiberglass laminates bonded with adhesives to Nomex honeycomb core. The test results were compared to proposed and current requirements for aircraft floor panel applications to demonstrate that the fire safety of the airplane could be improved without sacrificing mechanical performance of the aircraft floor panels.

Arnold, D. B.↗

On a numerical solution of the supersonic panel flutter eigenproblem

An automated digital computer procedure is presented in this paper which enables efficient solution of the eigenvalue problem associated with the supersonic panel flutter phenomena. The step-by-step incremental solution procedure is based on an inverse iteration technique which effectively utilizes solution results from the previous step in determining such results during the current solution step. Also, the computations are limited to the determination of a few specific roots only, which are expected to contain the flutter mode, and this is achieved at each step without having to compute any other root. The structural discretization achieved by the finite-element method yields highly banded stiffness, mass, and aerodynamic matrices; the aerodynamic matrix evaluated by the linearized piston theory is real but unsymmetric in nature. The solution algorithm presented in this paper fully exploits the banded form of the associated matrices, and the resulting computer program written in FORTRAN V for the JPL UNIVAC 1108 computer proves to be most efficient and economical when compared to existing procedures of such analysis. Numerical results are presented for a two-dimensional panel flutter problem.

Gupta, K. K.↗

Development of technology for the fabrication of reliable laminar flow control panels on subsonic transports

The feasibility of using porous composite materials (Kevlar, Doweave, and Leno Weave) as lightweight, efficient laminar flow control (LFC) surface materials is compared to the metallic 319L stainless Dynapore surfaces and electron beam drilled composite surfaces. Areas investigated include: (1) selection of the LFC-suitable surface materials, structural materials, and fabrication techniques for the LFC aircraft skins; (2) aerodynamic static air flow test results in terms of pressure drop through the LFC panel and the corresponding effective porosity; (3) structural design definition and analyses of the panels, and (4) contamination effects on static drop and effective porosity. Conclusions are presented and discussed.

Source record↗

Brazed Borsic/aluminum structural panels

A fluxless brazing process has been developed that minimizes degradation of the mechanical properties of Borsic/aluminum composites. The process, which employs 718 aluminum alloy braze, is being used to fabricate full scale Borsic/aluminum-titanium honeycomb-core panels for Mach 3 flight testing on the YF-12 aircraft and ground testing in support of the Supersonic Cruise Aircraft Research (SCAR) Program. The manufacturing development and results of shear tests on full scale panels are presented.

Bales, T. T.↗