Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Investigation on Microstructural Evolutions and Mechanical Properties of P92 Steel During Thermal Processing

The evolution of the microstructure of P92 steel during heat processing has a significant effect on the final performance of steel products and is thus an area of critical interest. Accordingly, the grain growth behavior of austenite and δ-ferrite changes in P92 steel is comprehensively investigated in this study through thermodynamic calculations and physical simulation. The results show that the A{sub C1}, A{sub C3} and γ–δ transformation temperatures of P92 steel are 841 °C, 878 °C and 1095 °C, respectively, which are comparable to the measured values of 850 °C, 879 °C and 1175 °C, respectively. When the temperature exceeds the A{sub C1} temperature, the austenite grain size increases with increasing temperature and longer holding times, and the growth rate of austenite grains increases with higher temperatures but decreases with holding time at a certain temperature. A model that shows the austenite grain growth kinetics is established: D{sup n} − D{sub 0}{sup n} = 2.03 × 10{sup 16}exp(− 498,770/RT)t, in which the time exponent n decreases from 4.52 to 2.11 with an increase in temperature from 1000 °C to 1200 °C due to the reduced pinning effect resultant of the dissolution of precipitates, M{sub 23}C{sub 6}, VX and NbX at 887 °C, 1073 °C and 1200 °C, respectively. The formation of δ-ferrite at 1200 °C when held for 600 s and 1300 °C when held for 60 ~ 600 s causes a smaller austenite grain size. The relationship between the evolution of the microstructure of P92 steel and the mechanical properties is also studied. The results show that the prior austenite grain size has an inverse relationship with impact energy and ultimate tensile strength at 620 °C, while the presence of soft δ-ferrite leads to a reduction in the microhardness, impact energy and ultimate tensile strength at 620 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure Analysis and Rheological Behavior of Magnesium Alloys at Semi-solid Temperature Range

Microstructure and rheological properties of AZ91 and Elektron 21 magnesium alloys in semi-solid state were studied. Differential scanning calorimetry revealed significant differences in melting range in analyzed materials. Isothermal annealing for 5, 30 and 80 min, in semi-solid range, corresponding to 50 and 70% of solid fraction, showed slower microstructure coarsening kinetics in Elektron 21 due to the presence of Zr- and RE-enriched precipitations. Ostwald ripening and coalescence resulted in decrease in grains density with increasing annealing time and temperature. Hardness after annealing showed overall tendency to diminish with soaking time probably due to the growth of average grain size. Rheological analysis showed tendency to lower the value of dynamic viscosity coefficient as shear rate rise, which confirmed non-Newtonian flow behavior. The highest values of dynamic viscosity coefficient were obtained for alloy AZ91.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Rotation Speed on the Microstructure and Mechanical Properties of Friction-Stir-Welded CuSn6 Tin Bronze

Four-mm-thick CuSn6 tin bronze plates were friction stir welded at a constant tool traverse speed of 100 mm min{sup −1}. Favorable joints could be obtained with rotation speeds ranging from 600 to 1000 rev min{sup −1}, and groove was found on the surface of the joint under 400 rev min{sup −1}. The microstructure of the weld nugget zone was characterized by equiaxed recrystallized grains with heterogeneity along the thickness direction. Moreover, the grain size of the thermo-mechanically affected zone and stir zone increased with the increase in rotation speed. Hardness of the stir zone was higher than that of other zones due to microstructural refinement. There was little change in tensile properties of the defect-free welded joints. During tensile test, all of the defect-free joints were fractured at heat-affected zone with typical plastic fracture.

36 MATERIALS SCIENCE↗
DOE OSTI2018

The Effects of Low Frequency on the Microstructure and Mechanical Properties of High-Strength Al-Mg Aluminum Alloys by Wire and Double-Pulsed Arc Additive Manufacturing

An innovative and high deposition efficiency process, the double-pulsed arc additive manufacturing process, is used to produce high-strength Al-Mg wall components. This dissertation investigates the electrical parameter acquisition, bead appearance, porosity morphology, microstructure and mechanical properties of additively manufactured high-strength Al-Mg wall components and how these are affected by the low frequency of the double-pulsed arc additive manufacturing process. Then, using this process at different low frequencies of 0, 1, 3, 5, 7 and 9 Hz, multilayer deposition experiments were performed. It can be observed that the deposit porosity is obviously eliminated compared with cold metal transfer (CMT) process. The bead appearance of the deposited aluminum wall varies clearly with low frequencies, and at a low frequency of 3 Hz, its appearance is the best of all. The optical observation of microstructure proves that the average grain size varies significantly with low frequency, and at a low frequency of 1 Hz, it is the smallest. In addition, the deposited wall showed maximum mean microhardness and maximum ultimate tensile strength at a low frequency of 3 Hz. Considering the deposited porosity and mechanical priorities, double-pulsed arc additive manufacturing with a frequency of 3 Hz is more suitable for making high-strength Al-Mg wall components than at other low frequencies.

36 MATERIALS SCIENCE↗
DOE OSTI2019

The Microstructure, and Mechanical and Corrosion Properties of As-Cast and As-Extruded Mg-2%Zn-x%Cu Alloys After Solution and Aging Heat Treatments

The effects of different Cu concentrations and heat treatment on the microstructure, mechanical and corrosion properties of the as-cast and hot-extruded Mg-2%Zn alloys were studied. The results showed that T6 heat treatment led to the dissolution of intermetallics and breaking the continuous networks of intermetallics. Also, the grain size of the base alloy decreased with further Cu additions after solution and aging heat treatments. Microstructural characterization indicated that Mg(Zn,Cu) and Mg(Zn,Cu){sub 2} intermetallics were formed which their volume fractions increased with exceeding Cu additions. Moreover, the addition of 3 wt.% Cu and T6 heat treatment increased the Brinell hardness of both as-cast and hot-extruded specimens reached to 94 HBN and 116 HBN, respectively. The optimum amounts of the ultimate tensile strength and elongation values obtained from 0.1 wt.% Cu addition for both conditions after T6 treatment which were 253 MPa, 11.5% and 263 MPa, 14.7%, respectively. However, more Cu addition (> 0.5 wt.%) deteriorated the tensile properties of the alloy due to the high volume fraction of intermetallics. The yield tensile strength increased continuously with different Cu additions for the cast and extruded alloys after solution and aging heat treatments. After T6 heat treatment, extruded alloys showed better anti-corrosion properties than those of the cast alloys, while the extruded Mg-2%Zn-0.1%Cu alloy exhibited the best anti-corrosion property. Further Cu addition increased the volume fraction of intermetallics and enhanced the corrosion rate which was due to the galvanic couple effect.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Preheated Microstructure Vis-à-vis Process Parameters and Characterization of Orange Peel in Incremental Forming of AA1050 Sheets

The present investigation systematically analyzes and compares the influence of microstructure and crystallographic texture of AA1050 sheet to that of the most critical process parameters, namely tool dimension, and incremental step depth, in single-point incremental forming (SPIF) process. The sheet samples were preheated at different temperatures to reform the original, i.e., distorted and misoriented grain distribution. The results from experimental and statistical analyses report higher sensitivity of global spring back, surface topography and forming limits strains to variations in microstructure and texture than tool diameter and incremental step depth. The preheating of the sheets resulted in the formation of preferential texture by grain reformation, which leads to the increase in the fraction of homogeneous orientated grains. Such grains increase the maximum forming limit strains and reduce the global spring back in SPIF. Fractography analysis of the failed components revealed that improvement in formability due to grain homogenization (developed texture) may be attributed to larger average void diameter. Empirical models were also developed, and optimized levels of parameters were identified to maximize the efficiency of the SPIF process. Further, qualitative and quantitative characterization of orange peel roughness was carried out by segregating the external formed surface into surfaces subjected to orange peel roughness and tool-induced texture.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effects of Laser Fluence on Microstructure and Bonding Characteristics of Wideband Laser-Deposited Nickel Composite Coatings

The wideband laser has shown great potential in metal–ceramic coatings deposition due to the high efficiency and low dilution rate. However, the effects of wideband laser process on microstructure evolution and bonding mechanism at the coatings/substrate interface are still a critical problem and need further investigation. In this work, nickel composite coatings are fabricated on the surface high-strength low-alloy steel. The effects of laser fluence on microstructure evolution, shear strength and fracture mechanism are studied. Results indicated the added WC particles were partly dissolved due to the high-power laser irradiation. Many block precipitates and dense eutectic were synthesized in composite coatings. Reinforced phases mainly consist of Cr{sub 5}B{sub 3}, Cr{sub 23}C{sub 6}, W{sub 2}C and Cr{sub 3}Ni{sub 2}. The dilution of Q550 steel contributed to the formation of nickel dendrites and facilitated a dense metallurgical bonding at coating/substrate interface when laser fluence was high. Shear strength tests indicated the laser fluence and shear strength had a positive correlation. For Ni60/WC composite coatings designed in these experiments, the recommend laser fluence should be higher than 55 J/mm{sup 2}, above which the shear strength could be greater than 200 MPa. Fracture surfaces indicated the failure mechanism of composite coatings was quasi-cleavage fracture.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Dual-Phase Heat Treatment on Microstructure and Mechanical Properties of S135 High-Strength Drill Pipe Steel

Effect of dual-phase heat treatment (DPHT) on microstructure and mechanical properties of S135 high-strength drill pipe steel was studied by means of optical microscope, scanning electron microscope and mechanical property testing. The results show that the ferrite–martensite dual-phase microstructures were obtained at 760-800 °C. With increase in DPHT temperature, the volume fraction of martensite increases and the ferrite decreases. When the DPHT temperature is low, martensite is distributed as an island on the ferrite matrix, and ferrite is distributed as an island on the martensite matrix when the DPHT temperature is high. The hardness and strength of the steel increase, the plasticity and toughness decrease, the steel changes from ductile fracture to brittle fracture and the micro-fracture morphology changes from dimple to cleavage with increase in DPHT temperature. The strain hardening exponent of the as-received steel shows one ‘n’ value, but exhibits two ‘n’ values after DPHT. When the DPHT temperature is 750 °C, the relative content of martensite in the duplex structure is 15-20%, and the impact energy of the steel is similar to that of the as-received S135 drill pipe steel, and the strength is increased by about 15%. Micropores and micro-cracks on the subsurface of tensile fracture surface are mainly formed at the martensite/ferrite phase boundary or in the martensite slit.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Room-Temperature Microstructural Evolution of Extruded AM80 Magnesium Alloys under Dynamic Loading

Dynamic compression tests were conducted using a split Hopkinson pressure bar along the transverse direction at strain rates (SRs) of 3200 and 6000 s{sup −1}. The initial microstructure significantly affected the flow stress behavior and microstructural evolution of the two studied AM80 magnesium alloys. Under the same SR loading, the as-extruded alloy exhibited an apparently higher flow stress. At a SR of 6000 s{sup −1}, the flow stress of the as-extruded alloy exhibited a visible decrease (~ 34 MPa) as the strain increased to ~ 0.2, whereas a constant flow stress was exhibited by the solution-treated alloy. High-density dislocations and mechanical twins were detected in the two alloys at a SR of 3200 s{sup −1}. Interestingly, dynamic recrystallization (DRX) with an average grain size of ~ 2 µm was only identified in the as-extruded alloy as the applied SR increased to 6000 s{sup −1}. The increased localized deformation in the as-extruded alloy due to the retained strain energy and high critical twinning stress improved the DRX driving force, thereby resulting in visibly different micrographs of the two alloys when impacted at the SR of 6000 s{sup −1}.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Cobalt on the Microstructure and Corrosion Behavior of Martensitic Age-Hardened Stainless Steel

To evaluate the influence of cobalt on the microstructure and pitting behavior of martensitic age-hardened stainless steel (MASS), the microstructures and electrochemical behaviors were characterized by optical microscopy, scanning electron microscopy, transmission electron microscopy, x-ray photoelectron spectroscopy, potentiodynamic curve, electrochemical impedance spectroscopy, and Mott–Schottky analysis. Results indicated that adding cobalt reduced the grain size of the original austenite, refined the lath martensite, inhibited the precipitation of Cu-rich phases, and increased the content of reversed austenite. Compared with the cobalt-free steel, the cobalt-containing steel has a higher pitting potential, lower corrosion current density, and higher pitting resistance. The primary components of the passive film grown on the cobalt-free steel included (Cr, Fe) oxides, such as Cr{sub 2}O{sub 3}, Cr(OH){sub 3}, FeOOH, and Fe{sub 2}O{sub 3}. The cobalt-containing steel included the aforementioned components as well as Co, which was attributed to the formation of the passive film in the forms of CoFe{sub 2}O{sub 4}, Co(OH){sub 2}, and CoO. In addition, the synergy of the refined lath martensite and the precipitation of the Cu-rich phase induced an increase in corrosion resistance in MASS containing cobalt.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructural Characteristics and Mechanical Properties of Friction-Stir-Welded CuSn6 Tin Bronze

Tin bronze is widely applied in various industries for its excellent wear and corrosion resistance. Friction stir welding is a solid-state welding process, which generates less heat and avoids the melting-related defects. CuSn6 tin bronze plates of 4 mm in thickness were friction-stir-welded at welding speeds ranging from 50 to 150 mm/min under a constant rotation speed. The microstructural and mechanical properties of joints were investigated. The microstructure of the stir zone consists of refined equiaxed grains. The grain size decreased from top to bottom of the welds. The mean grain size is increased with increasing welding speed. The largest strength and elongation of welded joints were both obtained at the welding speed of 100 mm/min. During tensile test, all of the joints were fractured at the heat affected zone of retreating side with typical plastic fracture feature, since the grains were coarsened by welding heat.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Microstructure Refinement on Hardness Homogeneity of Aluminum Alloy 1100 Processed by Accumulative Roll Bonding

This work examines the effect of grain refinement via accumulative roll bonding (ARB) on the homogeneity of microstructure and hardness through the thickness of commercially pure aluminum AA1100 sheets. The use of 7 cycles of ARB was shown to produce homogeneous ultrafine-grained microstructure, reducing the grain size to 0.46 and 1.03 µm in normal direction and rolling direction, respectively. Examination by electron backscattered diffraction indicates that continuous dynamic recrystallization was the main mechanism for the formation of submicron equiaxed grains bounded with high-angle grain boundaries (HAGBs). The fraction of HAGBs increased gradually reaching a maximum of 71.6% after 7 cycles. Through-thickness hardness measurements using Vickers and nanoindentation tests show an increase from 43.5 Hv (0.85 GPa) for as-received sample to 63 Hv (1.1 GPa) after 7 cycles. The heterogeneity in hardness through the thickness of the as-received material was shown to restrain the evolution of uniform hardness across the sheet thickness with increasing ARB cycles. Tensile tests showed that the tensile strength is increased to 250 MPa, which is about 2 times its initial value. Owing to the high stacking fault energy of AA1100, strong dynamic recovery occurred with increasing ARB strain which was balanced with the strain hardening property of the material. This resulted in plastic instability at small strains and thus early necking during the tensile test.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Y{sub 2}O{sub 3} Addition on the Microstructure, Wear Resistance, and Corrosion Behavior of W-4.9Ni-2.1Fe Heavy Alloy

Binding and particle phases are the two important parameters influencing materials properties. In this study, a series of novel W-4.9Ni-2.1Fe-xY{sub 2}O{sub 3} (in weight%) alloys with different Y{sub 2}O{sub 3} contents are prepared by secondary ball milling and spark plasma sintering (SPS) techniques to obtain uniformly distributed γ-(Ni, Fe) binding phases and finer grains. The microstructure, mechanical, wear resistance, and corrosion behavior of the sintered bodies with different Y{sub 2}O{sub 3} were obtained by x-ray diffraction, scanning electron microscopy, Rockwell hardness tester, friction wear tester, and three-dimensional profile instruments. The results showed that a certain addition of Y{sub 2}O{sub 3} led to refined grains and uniformed microstructures; but, if excessive, a weak grain refinement would be appeared. Moreover, the grain size tends to be stable with enhancing of the Y{sub 2}O{sub 3} content. Considering properties such as density, hardness, compression yield strength, grain size, and uniform distribution of tungsten hard phase and γ-(Ni, Fe) binding phase, the comprehensive optimal amount of 0.7 wt.% of Y{sub 2}O{sub 3} was attained for the alloy. Meanwhile, the SPS sintered body also exhibited the best friction, wear behavior, and corrosion resistance in 3.5% of NaCl solution.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Heat Treatment on Microstructure and Mechanical Properties of Ti-6Al-4V-1.5Mn Fabricated by Powder Metallurgy

Ti-6Al-4V-1.5Mn alloy was prepared by powder metallurgy and solid solution aging treatment. Effect of composition segregation on properties of the titanium alloy was eliminated, and microstructure and the mechanical properties of the alloy were studied. Results show that the microstructure of Ti-6Al-4V-1.5Mn is composed of homogeneous α + β phase, and the optimal mechanical properties of the alloy are obtained when the solution temperature is 950 °C and the aging temperature is 460 °C. Analysis of the fracture illustrates that a small amount of dimple was found in the section and the fracture of the material was quasi-cleavage fracture.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Combined Torsion and Tension on the Microstructure and Fracture Behavior of 316L Austenitic Stainless Steel

In this study, the microstructure evolution and fracture behavior of 316L austenitic stainless steel (ASS) deformed by torsion–tension at room temperature was systematically investigated. During combined tension and torsion, the grain size was refined with increasing shear strain. In addition, the microtexture exhibited a preferred orientation with increasing shear stress. The metastable austenite underwent phase transition when the shear stress increased. The shear stress affected the fracture morphology, and dimples with different sizes and depths were observed for different pre-torsions. The dislocation density increased significantly owing to severe shear deformation. In addition, the dislocation structure evolved and subgrains appeared with the accumulation of shear strain during this combined deformation. The result showed that pre-torsion deformation plays an important role in improving the comprehensive performance and controlling the microstructure evolution of the sample subjected to tension deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Deformation Behavior and Microstructural Evolution of Reeled Pipeline Steels during Cyclic Plastic Deformation

API X60 steel used for reeled pipeline was subjected to different amounts of cyclic plastic deformation (CPD) by multiple tension–compression tests in order to study the deformation behavior and microstructural evolution during each stage of reel-lay installation process. It was found that the yield strength was significantly reduced by about 110 MPa during the first CPD cycle due to the Bauschinger effect. However, the yield strength was little affected by the subsequent CPD cycles, and the yield strength difference between tension and compression tended to reach a steady-state value of 23 MPa after multiple CPD cycles. With the increase in CPD cycles, the proportion of low-angle grain boundaries declined from 50.9 to 35.7%, and the CPD contributed to the formation of immovable dislocation walls and cells due to the dislocation rearrangement, causing the stable yield strength. The CPD process with strain level of 3% had no prominent effect on the tensile strength and elongation, because the change in microstructures was not enough to alter the work hardening completely after multiple CPD cycles.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure Evolution and Mechanical Properties of the AZ91 Magnesium Alloy with Sr and Ti Additions in the As-Cast and As-Aged Conditions

Effect of different amounts of Sr and Ti additions with T6 heat treatment on microstructure and mechanical properties of the AZ91 alloy was investigated. The microstructure of the AZ91 alloy is consisted of the α-Mg phase surrounded by the semicontinuous network of β-Mg{sub 17}Al{sub 12} intermetallics. The average grain size and volume fraction of β phase decreased up to 1 wt.% Sr and 0.1 wt.% Ti additions. Exceeding Ti additions led to increase in both grain size and volume fraction. It was found that the grain refinement mechanism of AZ91 alloys with Sr additions was grain restriction factor. Also, 0.1 wt.% Ti addition could refine the grain structure of the AZ91 alloy by the formation of Al{sub 3}Ti particles that act as nucleation sites for the α-Mg phase. Furthermore, adding 1 wt.% Sr and 0.1 wt.% Ti enhanced the hardness values for both cast and aged AZ91 alloy. Moreover, ultimate tensile strength and tensile elongation values reached their maximum amounts with the 0.5 wt.% Sr and 0.1 wt.% Ti additions and more Sr and Ti additions deteriorated the mechanical properties of cast and aged AZ91 alloys. The fracture surface characterizations had good relations with the tensile properties. The fracture modes were cleavage and quasi-cleavage in the cast and aged AZ91 alloys. Furthermore, the optimum levels of Sr and Ti additions altered the fracture modes to more quasi-cleavage fractures.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Electropulsing on Surface Mechanical Behavior and Microstructural Evolution of Inconel 718 during Ultrasonic Surface Rolling Process

In the current study, the surface mechanical behavior and microstructural evolution of Inconel 718 superalloy processed by the ultrasonic surface rolling process (USRP) and electropulsing-assisted ultrasonic surface rolling process (EP-USRP) were carefully analyzed. The experimental results suggested that after EP-USRP with a frequency of 400 Hz, significant enhancements in Vickers microhardness and nanoindentation hardness were achieved compared to those of USRP specimens, with increases of 13.6 and 9.9%, respectively. Moreover, the machined surface quality, wear resistance, and thermal stability were also improved after EP-USRP (400 Hz). These enhancements in mechanical behavior are closely related to the microstructural evolution induced by electropulsing. Under the coupling of thermal and athermal effects of high-energy electropulsing, the deformation limit of USRP is surpassed and a new balance is achieved between the electropulsing softening effect and the ultrasonic rolling hardening effect. Therefore, further grain refinement, improved plastic deformation ability in the strengthened layer, and the interaction effect between nano-sized precipitates and grain boundaries are probably the main reasons for these results.

36 MATERIALS SCIENCE↗