Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “materials modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Photoelastic studies of advanced lap joint concept

Photoelasticity was introduced as a quantitative tool in the experimental stress analysis of anisotropic birefringent composite model materials. The investigation was divided into three parts: (1) separation of principal stresses or strains, (2) photoelastic calibration, and (3) development of model-prototype relations.

Prabhakaran, R.↗

Uncatalysed and catalysed soot combustion under NO{sub x} + O{sub 2}: Real diesel versus model soots

In this work, the uncatalysed and catalysed combustion of two commercial carbon blacks and three diesel soot samples were analysed and related to the physico-chemical properties of these carbon materials. Model soot samples are less reactive than real soot samples, which can be attributed, mainly, to a lower proportion in heteroatoms and a higher graphitic order for the case of one of the carbon blacks. Among the diesel soot samples tested, the most relevant differences are the volatile matter/fixed carbon contents, which are directly related to the engine operating conditions (idle or loaded) and to the use of an oxidation catalyst or not in the exhaust. The soot collected after an oxidation catalyst (A-soot) is more reactive than the counterpart virgin soot obtained under the same engine operating modes but before the oxidation catalyst. The reactivity of the different soot samples follows the same trend under uncatalysed and catalysed combustion, the combustion profiles being always shifted towards lower temperatures for the catalysed reactions. The differences between the soot samples become less relevant in the presence of a catalyst. The ceria-zirconia catalysts tested are very effective not only to oxidise soot but also to combust the soluble organic fraction emitted at low temperatures. The most reactive soot (A-soot) exhibits a T{sub 50%} parameter of 450 C when using the most active catalyst. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Understanding Automotive Exhaust Catalysts Using a Surface Science Approach: Model NOx Storage Materials

The structure-reactivity relationships of model BaO-based NOx storage/reduction catalysts were investigated under well controlled experimental conditions using surface science analysis techniques. The reactivity of BaO toward NO2, CO2, and H2O was studied as a function of BaO layer thickness [0\hBaO\30 monolayer (ML)], sample temperature, reactant partial pressure, and the nature of the substrate the NOx storage material was deposited onto. Most of the efforts focused on understanding the mechanism of NO2 storage either on pure BaO, or on BaO exposed to CO2 or H2O prior to NO2 exposure. The interaction of NO2 with a pure BaO film results in the initial formation of nitrite/nitrate ion pairs by a cooperative adsorption mechanism predicted by prior theoretical calculations. The nitrites are then further oxidized to nitrates to produce a fully nitrated surface. The mechanism of NO2 uptake on thin BaO films (\4 ML), BaO clusters (\1 ML) and mixed BaO/Al2O3 layers are fundamentally different: in these systems initially nitrites are formed only, and then converted to nitrates at longer NO2 exposure times. These results clarify the contradicting mechanisms presented in prior studies in the literature. After the formation of a nitrate layer the further conversion of the underlying BaO is slow, and strongly depends on both the sample temperature and the NO2 partial pressure. At 300 K sample temperature amorphous Ba(NO3)2 forms that then can be converted to crystalline nitrates at elevated temperatures. The reaction between BaO and H2O is facile, a series of Ba(OH)2 phases form under the temperature and H2O partial pressure regimes studied. Both amorphous and crystalline Ba(OH)2 phases react with NO2, and initially form nitrites only that can be converted to nitrates. The NO2 adsorption capacities of BaO and Ba(OH)2 are identical, i.e., both of these phases can completely be converted to Ba(NO3)2. In contrast, the interaction of CO2 with pure BaO results in the formation of a BaCO3 layer that prevents to complete carbonation of the entire BaO film under the experimental conditions applied in these studies. However, these ‘‘carbonated’’ BaO layers readily react with NO2, and at elevated sample temperature even the carbonate layer is converted to nitrates. The importance of the metal oxide/metal interface in the chemistry on NOx storage-reduction catalysts was studied on BaO(\1 ML)/Pt(111) reverse model catalysts. In comparison to the clean Pt(111), new oxygen adsorption phases were identified on the BaO/Pt(111) surface that can be associated with oxygen atoms strongly adsorbed on Pt atoms at the peripheries of BaO particles. A simple kinetic model developed helped explain the observed thermal desorption results. The role of the oxide/metal interface in the reduction of Ba(NO3)2 was also substantiated in experiments where Ba(NO3)2/O/Pt(111) samples were exposed to CO at elevated sample temperature. The catalytic decomposition of the nitrate phase occurred as soon as metal sites opened up by the removal of interfacial oxygen via CO oxidation from the O/Pt(111) surface. The temperature for catalytic nitrate reduction was found to be significantly lower than the onset temperature of thermal nitrate decomposition. We gratefully acknowledge the US Department of Energy (DOE), Office of Science, Division of Chemical Sciences, Geosciences, and Biosciences for the support of this work. The research described in this paper was performed at the Environmental Molecular Sciences Laboratory (EMSL), a national user facility sponsored by the DOE Office of Biological and Environmental Research and located at the Pacific Northwest National Laboratory (PNNL). PNNL is operated for the US DOE by Battelle under contract number DE-AC05-76RL01830.

Environmental Molecular Sciences Laboratory↗

CARBON NANOTUBES: PROPERTIES AND APPLICATIONS

Carbon nanotubes were discovered in 1991 as a minority byproduct of fullerene synthesis. Remarkable progress has been made in the ensuing years, including the discovery of two basic types of nanotubes (single-wall and multi-wall), great strides in synthesis and purification, elucidation of many fundamental physical properties, and important steps towards practical applications. Both the underlying science and technological potential of SWNT can profitably be studied at the scale of individual tubes and on macroscopic assemblies such as fibers. Experiments on single tubes directly reveal many of the predicted quantum confinement and mechanical properties. Semiconductor nanowires have many features in common with nanotubes, and many of the same fundamental and practical issues are in play – quantum confinement and its effect on properties; possible device structures and circuit architectures; thermal management; optimal synthesis, defect morphology and control, etc. In 2000 we began a small effort in this direction, conducted entirely by undergraduates with minimal consumables support from this grant. With DOE-BES approval, this grew into a project in parallel with the carbon nanotube work, in which we studied of inorganic semiconductor nanowire growth, characterization and novel strategies for electronic and electromechanical device fabrication. From the beginnings of research on carbon nanotubes, one of the major applications envisioned was hydrogen storage for fuel-cell powered cars and trucks. Subsequent theoretical models gave mixed results, the most pessimistic indicating that the fundamental H2-SWNT interaction was similar to flat graphite (physisorption) with only modest binding energies implying cryogenic operation at best. New material families with encouraging measured properties have emerged, and materials modeling has gained enormously in predictive power, sophistication, and the ability to treat a realistically representative number of atoms. One of the new materials, highly porous carbide-derived carbons (CDC), is the subject of an add-on to this grant awarded to myself and Taner Yildirim (NIST). Results from the add-on led eventually to a new 3-year award DE-FG02-08ER46522 “From Fundamental Understanding to Predicting New Nanomaterials for High Capacity Hydrogen Storage”, $1000K, (05/31/2008 - 05/01/2011) with Taner Yildirim and myself as co-PI’s.

08 HYDROGEN↗

Coupled thermal/chemical/mechanical modeling of energetic materials in ALE3D

We must improve our ability to model the response of energetic materials to thermal stimuli and the processes involved in the energetic response. We have developed and used a time step option to efficiently and accurately compute the hours that the energetic material can take to react. Since on these longer film scales, materials can be expected to have significant motion, it is even more important to provide high-order advection for all components, including the chemical species. We show an example cook-off problem to illustrate these capabilities.

WEAPONS↗

Determination of Material Constitutive Laws for Inconel 718 Superalloy Under Different Strain Rates and Working Temperatures

In this paper, a special procedure for the prediction of parameters of the Johnson–Cook constitutive material models is proposed based on the experimental data and specially developed MATLAB scripts which allow advanced modeling of complex 3D response surfaces. Experimental investigations concern two various strain rates of 10{sup −3} and 10{sup 1} 1/s and the testing temperature ranging from the ambient up to 700 °C. As a result, a set of mathematical equations which fit the experimental data is determined. The applicability of the experimentally derived constitutive models to the FEM modeling of real machining processes of Inconel 718 alloy is verified.

36 MATERIALS SCIENCE↗

Surface oxygen exchange kinetics of mixed conducting oxides: Dilatometric vs electrical conductivity relaxation study

The surface oxygen exchange kinetics of mixed ionic-electronic conducting (MIEC) oxides play a crucial role in a variety of applications, including solid oxide fuel/electrolysis cells (SOFCs/SOECs), permeation membranes and sensors. To date, a variety of methods, including isotope exchange, electrical conductivity, optical absorptivity and thermogravimetry relaxation, and impedance spectroscopy have been used to measure the oxygen exchange coefficient of MIEC oxides. Each of these methods have their advantages and limitations, depending on the physical and chemical properties of the investigated materials and their sample dimensions and densities. Here, we demonstrate the ability to precisely measure the surface oxygen exchange coefficient (k chem ) of MIEC model material Pr 0.1 Ce 0.9 O 2-δ (PCO) by use of dilatometric relaxation measurements, particularly of interest for materials that exhibit larger chemical expansion coefficients. This is achieved by use of porous bulk specimens to ensure that the contribution of oxygen exchange to the overall kinetics is dominant. We demonstrate that k chem values extracted from chemical expansion relaxation measurements on PCO are nearly identical to those derived from electrical conductivity relaxation measurements. As a result, this provides the opportunity to precisely investigate the oxygen exchange and chemical expansion kinetics of a wide range of materials used in high-temperature applications, particularly where more conventional methods are difficult or inappropriate to apply.

(Pr,Ce)O2-x↗

Planar Defect Layers Template a High-Pressure InBi Polymorph

The short- and long-range order of III–V materials under high pressure has long been the subject of debate, with advancements in structural characterization leading to significant revisions to the accepted structural models. Despite these revisions, previous high-pressure structural assignments in the In–Bi system include the site-disordered β-Sn structure type, a structure type demonstrated to be nonexistent in analogous III–V systems. While X-ray diffraction is consistent with site disordering in InBi at high pressure, cluster expansion calculations indicate that disordering requires temperatures above 3000 K. Here, we propose InBi as a model material for studying unique high-pressure planar defects due to its highly anisotropic stress-dependent properties and structure. Specifically, we identify two sets of planar defects that mimic the diffraction pattern of a site disordered β-Sn structure type and are compatible with the calculated disorder barrier. We derive these defects by symmetry relations over crystallographic transitions. Density functional theory calculations of the proposed defects suggest that these defects are stabilized by diminishing interlayer separations with pressure. Further, we find that one of the proposed defects closely resembles a bulk high-pressure phase of InBi, InBi-ϵ, and we assert that the proposed defects order upon heating, acting as a template for InBi-ϵ growth. The proposed defects and their electronic structure provide a basis for the trend of superconducting critical temperature with increasing pressure. These methods for identifying defects are generalizable to other materials with reports of site disorder at high pressure, prompting a broader search for related high-pressure defects.

36 MATERIALS SCIENCE↗

A multiscale insight into the growth of h-BN: effect of the enclosure

Abstract There is a lack of knowledge on the fundamental growth mechanisms governing the characteristics of 2D materials synthesized by the chemical vapor deposition (CVD) technique and their correlation with experimentally controllable parameters, which hindered their wafer-scale synthesis. Here, we pursued an analytical and computational approach to access the system states that are not experimentally viable to address these critical needs. We developed a multiscale computational framework correlating the macroscale heat and mass flow with the mesoscale morphology of the as-grown 2D materials by solving the coupled system of heat/mass transfer and phase-field equations. We used hexagonal boron nitride (h-BN) as our model material and investigated the effect of substrate enclosure on its growth kinetics and final morphology. We revealed a lower concentration with a more uniform distribution on the substrate in an enclosed-growth than open-growth. It leads to a more uniform size distribution of the h-BN islands, consistent with existing experimental investigations.

Materials Science↗

Evaluation and Modeling of Edge-Seal Materials for Photovoltaic Applications

Because of the sensitivity of some photovoltaic devices to moisture-induced corrosion, they are packaged using impermeable front- and back-sheets along with an edge seal to prevent moisture ingress. Evaluation of edge seal materials can be difficult because of the low permeation rates involved and/or non-Fickian behavior. Here, using a Ca film deposited on a glass substrate, we demonstrate theevaluation of edge seal materials in a manner that effectively duplicates their use in a photovoltaic application and compare the results with standard methods for measuring water vapor transport. We demonstrate how moisture permeation data from polymer films can be used to estimate moisture ingress rates and compare the results of these two methods. Encapsulant materials were also evaluated forcomparison and to highlight the need for edge seals. Of the materials studied, desiccant filled polyisobutylene materials demonstrate by far the best potential to keep moisture out for a 20 to 30 year lifetime.

14 SOLAR ENERGY↗

Attenuation of waves in a viscoelastic peridynamic medium

The effect of spatial nonlocality on the decay of waves in a dissipative material is investigated. The propagation and decay of waves in a one-dimensional, viscoelastic peridynamic medium is analyzed. Both the elastic and damping terms in the material model are nonlocal. Waves produced by a source with constant amplitude applied at one end of a semi-infinite bar decay exponentially with distance from the source. The model predicts a cutoff frequency that is influenced by the nonlocal parameters. A method for computing the attenuation coefficient explicitly as a function of material properties and source frequency is presented. Here, the theoretical results are compared with direct numerical simulations in the time domain. The relationship between the attenuation coefficient and the group velocity is derived. It is shown that in the limit of long waves (or small peridynamic horizon), Stokes’ law of sound attenuation is recovered.

97 MATHEMATICS AND COMPUTING↗

Being Scientific: Saryu Fensin: Sparking innovations in both materials science and shock physics

As an enterprising materials scientist, Saryu Fensin leverages both experiments and simulations to improve understanding of how materials behave when subjected to extreme forces. Her aim is to use the complementary techniques to design and develop innovative materials for use in extreme conditions such as stockpile-focused applications. “To certify our stockpile with confidence, we need to understand the role a material’s microstructure plays in determining its dynamic properties,” Saryu says. “I’m hoping to solve this puzzle and improve our predictive capability to model material response in extreme conditions. Achieving this kind of specific controlled functionality of materials could have a big impact on the Laboratory’s national security science mission.” Her tools include molecular dynamics, Monte Carlo methods, gas gun experiments, metallography and various microscopy techniques. She looks forward to the prospect of new capabilities that could let her "see" inside materials.

36 MATERIALS SCIENCE↗

Foreign body impact event damage formation in composite structures

This report discusses a methodology that can be used to assess the effect of foreign body impacts on composite structural integrity. The described effort focuses on modeling the effect of a central impact on a 5 3/4 inch filament wound test article. The discussion will commence with details of the material modeling that was used to establish the input properties for the analytical model. This discussion is followed by an overview of the impact assessment methodology. The progress on this effort to date is reviewed along with a discussion of tasks that have yet to be completed.

Bucinell, Ronald B.↗

Multiscale Modeling of Structurally-Graded Materials Using Discrete Dislocation Plasticity Models and Continuum Crystal Plasticity Models

A multiscale modeling methodology that combines the predictive capability of discrete dislocation plasticity and the computational efficiency of continuum crystal plasticity is developed. Single crystal configurations of different grain sizes modeled with periodic boundary conditions are analyzed using discrete dislocation plasticity (DD) to obtain grain size-dependent stress-strain predictions. These relationships are mapped into crystal plasticity parameters to develop a multiscale DD/CP model for continuum level simulations. A polycrystal model of a structurally-graded microstructure is developed, analyzed and used as a benchmark for comparison between the multiscale DD/CP model and the DD predictions. The multiscale DD/CP model follows the DD predictions closely up to an initial peak stress and then follows a strain hardening path that is parallel but somewhat offset from the DD predictions. The difference is believed to be from a combination of the strain rate in the DD simulation and the inability of the DD/CP model to represent non-monotonic material response.

Saether, Erik↗

Test and Analysis Correlation for Sandwich Composite Longitudinal Joint Specimens

The NASA Composite Technology for Exploration (CTE) project is tasked with evaluating methods to analyze and manufacture composite joints for potential use in block upgrades to the Space Launch System (SLS) launch-vehicle structures such as the Payload Attach Fitting (PAF). To perform this task, the CTE project has initiated test and analysis correlation studies for composite joints under various loading conditions. Herein, NASA-developed numerical models are correlated with the experimental results from a series of tension tests. Pretest strain results matched the far-field test data well, but did not capture the nonlinear response in the vicinity of the joint. A refined pretest analytical model was modified to represent progressive failure of the specimens at failure locations observed during the experimental tests. The nonlinear strain response from this progressive failure model predicted the delamination failure load within 15% of the test data, but underpredicted the nonlinearity of the strain response. Further study of composite material models that account for the nonlinear shear response of fabric composites is recommended for the composite joint structures considered in this paper.

Mason, Brian H.↗

Screening sensitivity analysis of a PWR fuel assembly FEM structural model

Within the present project, computational methods to describe the static mechanical response of PWR fuel assemblies (FA) in the reactor core are developed. For this purpose a structural model of a PWR fuel assembly has been implemented with the Finite Element Method (FEM) using the ANSYS APDL Mechanical code. The purpose of the model is to investigate the long-term creep deformation of the fuel assemblies in the reactor core, commonly known as fuel assembly bow. FA bow is considered to be a complex process with a large number of influencing mechanisms and many only roughly known boundary conditions. Uncertainty and sensitivity analyses are a common way to investigate the predictive power and reliability of such complex models. Hence, as a first approach to understand the importance of the many model parameters, a qualitative sensitivity analysis of the model was conducted using the screening method proposed by Morris. In the first part of the paper, the FA structural model and its principal parameters are presented. The second part presents first the different simulation experiments used for the screening analyses. Based on the model description, relevant input parameters are then identified and a typical range of values is determined. The sensitivity analysis is performed in two subsequent steps. First, the model is screened for influential stiffness parameters with the objective of stiffening the FA structure. Second, the influence of the uncertain boundary conditions and material models on the FA creep deformation is tested. For the considered FA design it is concluded that the influence of the involved uncertainties is comparable to the influence of the parameters which can increase the stiffness. An integral approach accounting for these uncertainties is hence necessary to predict FA bow reliably in order to take additional measures for a further reduction of FA bow amplitudes. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

The effectiveness of D 2 pellet injection in reducing intra-ELM and inter-ELM tungsten divertor erosion rates in DIII-D during the Metal Rings Campaign

Abstract Edge localized modes (ELMs) in H-mode plasmas erode plasma-facing components (PFCs) and lead to impurities in the core, reducing confinement. This study analyzes D 2 pellet injection on the DIII-D fusion experiment used as an ELM mitigation technique applied during the 2016 tungsten Metal Rings Campaign to reduce W erosion during ELMs. The 400.9 nm photon wavelength line emission intensity of tungsten atoms (WI) filterscope channels and Langmuir probes were used to infer the gross erosion rate of tungsten-coated tiles installed in the divertor of DIII-D. D 2 mass injection rates ranging from 34 to 41 arbitrary units (A.U.) and no D 2 injection resulted in a similar total W erosion rate during ELMs (intra-ELM). On average, results show a 29% increase in the total gross W erosion rate with intermediate mass injection rates (∼13–23 A.U.) compared to the no pellets and the highest injection rate cases. On average, the fast D 2 mass injection rate cases had 15% less erosion in the inter-ELM phase than the case with no pellets. Generally, higher D 2 mass injection rates increased the ELM frequency, and the highest injection rates reduced the average erosion per ELM and fractional carbon impurities at the top of the pedestal by nearly 40% when compared to the no-pellet case. As expected, a higher D 2 pellet injection rate led to a higher plasma density and lower plasma temperature in the divertor. Additionally, an increasing divertor inter-ELM plasma electron density directly correlated to more frequent pellet injection and a decrease in both the average gross intra-ELM W erosion and the total gross intra-ELM W erosion rate. Simulations of intra-ELM erosion using the ‘free-streaming plus recycling model’ (FSRM) underestimate W erosion during pellet injection by about 30% on average. The discrepancies between the experimental measurements and the FSRM intra-ELM W erosion predictions are postulated to be due to C/W material mixing. A simple analytic mixed-material model is presented and results in better agreement with the experimental data. These results highlight the importance of incorporating the effects of a mixed-material layer in the analysis of PFC erosion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Fuel Performance Analysis of Fast Flux Test Facility MFF-3 and -5 Fuel Pins Using BISON with Post Irradiation Examination Data

Using the BISON fuel-performance code, simulations were conducted of an automated process to read initial and operating conditions from the Pacific Northwest National Laboratory (PNNL) database and reports, which contain metallic-fuel data from the Fast Flux Test Facility (FFTF) MFF Experiments. This work builds on previous modeling efforts involving 1977 EBR-II metallic fuel pins from experiments. Coupling the FFTF PNNL reports to BISON allowed for all 338 pins from MFF-3 and MFF-5 campaigns to be simulated. Each BISON simulation contains unique power and flux histories, axial power and flux profiles, and coolant-channel flow rates. Fission-gas release (FGR), fuel axial swelling, cladding profilometry, and burnup were all simulated in BISON and compared to available post-irradiation examination (PIE) data. Cladding profilometry, FGR, and fuel axial swelling simulation results for full-length MFF metallic pins were found to be in agreement with PIE measurements using FFTF physics and models used previously for EBR-II simulations. The main two peaks observed within the cladding profilometry were able to be simulated, with fuel-cladding mechanical interaction (FCMI), fuel-cladding chemical interaction (FCCI), and thermal and irradiation-induced creep being the cause. A U-Pu-Zr hot-pressing model was included in this work to allow pore collapse within the fuel matrix. This allowed better agreement between BISON-simulated cladding profilometry and PIE measurements for the peak caused by FCMI. This work shows that metallic fuel models used to accurately represent fuel performance for smaller EBR-II pins may be used for full-length metallic fuel, such as FFTF MFF assemblies and the Versatile Test Reactor (VTR). As new material models and PIE measurements become available, FFTF MFF assessment cases will be reassessed to further BISON model development.

36 MATERIALS SCIENCE↗