SEARCH · Engineering Papers

Results for “mass conservation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

All sources NASA NTRS DOE OSTI

NASA NTRS1992

Solar dynamic modules for Space Station Freedom: The relationship between fine-pointing control and thermal loading of the aperture plate

Dynamic simulations of Space Station Freedom (SSF) configured with solar dynamic (SD) power modules were performed. The structure was subjected to Space Shuttle docking disturbances, while being controlled with a 'natural' vibration and tracking control approach. Three control cases were investigated for the purpose of investigating the relationship between actuator effort, SD pointing, and thermal loading on the receiver aperture plate. Transient, one-dimensional heat transfer analyses were performed to conservatively predict temperatures of the multi-layered receiver aperture plate assembly and thermal stresses in its shield layer. Results indicate that the proposed aperture plate is tolerant of concentrated flux impingement during short-lived structural disturbances. Pointing requirements may be loosened and the requirement control torques lessened from that previously specified. Downsizing and simplifying the joint drive system should result in a considerable savings mass.

Quinn, Roger D.↗

NASA NTRS1995

Equiparatition of energy for turbulent astrophysical fluids: Accounting for the unseen energy in molecular clouds

Molecular clouds are observed to be partially supported by turbulent pressure. The kinetic energy of the turbulence is directly measurable, but the potential energy, which consists of magnetic, thermal, and gravitational potential energy, is largly unseen. We have extended previous results on equipartition between kinetic and potential energy to show that it is likely to be a very good approximation in molecular clouds. We have used two separate approaches to demonstrate this result: For small-amplitude perturbations of a static equilibrium, we have used the energy principle analysis of Bernstein et al. (1958); this derivation applies to perturbations of arbitary wavelength. To treat perturbations of a nonstatic equilibrium, we have used the Lagrangian analysis of Dewar (1970); this analysis applies only to short-wavelength perturbations. Both analysis assume conservation of energy. Wave damping has only a small effect on equipartition if the wave frequency is small compared to the neutral-ion collision frequency; for the particular case we considered, radiative losses have no effect on equipartition. These results are then incorporated in a simple way into analyses of cloud equilibrium and global stability. We discuss the effect of Alfvenic turbulence on the Jeans mass and show that it has little effect on the magnetic critical mass.

Zweibel, Ellen G.↗

NASA NTRS1994

Choked flow effects in the NSI driven pin puller

This paper presents an analysis for pyrotechnic combustion and pin motion in the NASA Standard Initiator (NSI) actuated pin puller. The conservation principles and constitutive relations for a multi-phase system are posed and reduced to a set of eight ordinary differential equations which are solved to predict the system performance. The model tracks the interactions of the unreacted, incompressible solid pyrotechnic, incompressible condensed phase combustion products, and gas phase combustion products. The model accounts for multiple pyrotechnic grains, variable burn surface area, and combustion product mass flow rates through an orifice located within the device. Pressure-time predictions compare favorably with experimental data. Results showing model sensitivity to changes in the cross-sectional area of the orifice are presented.

Gonthier, Keith A.↗

DOE OSTI2025

Asymmetric loading of TnsE regulates Tn7 targeting of DNA replication structures

Abstract Tn7 transposable elements are known for their sophisticated target-site selection mechanisms. For the prototypical Tn7 element, dedicated transposon-encoded proteins direct insertions to either a conserved site in the chromosome or replicating DNA structures in conjugal plasmids, ensuring the vertical and horizontal spread of the element. While the pathway targeting the attTn7 site in the bacterial chromosome has been extensively studied, the pathway targeting DNA replication structures remains poorly understood. We have used an integrative structural biology approach to elucidate how the Tn7-encoded protein TnsE recognizes replication sites. Using native mass spectrometry, we found that TnsE forms 1:1 and 2:1 (TnsE:DNA) complexes on 3′-recessed DNA, with gain-of-function TnsE variants favoring the formation of 2:1 complexes. Structural characterization confirms that two TnsE molecules bind to DNA with the C-terminal domain of the protein recognizing duplex DNA, leaving the N-terminal domain to impose DNA substrate specificity and recruit the core transposition machinery. Collectively, our work is consistent with a model where TnsE-mediated target-site selection relies on the formation of an asymmetric TnsE:DNA complex to recruit the Tn7 transposase to DNA replication structures.

Biochemistry & Molecular Biology↗

DOE OSTI2024

Numerical Improvements in Magnetohydrodynamic, Pulsed Power Simulations of Near-Target Plasmas

Magnetohydrodynamic (MHD) simulations of pulsed power experiments frequently result in unphysical runaway heating when extended to low values of mass density. Traditionally, this has been addressed by the use of conductivity floors below which the plasma is given an arbitrarily low conductivity value. Here, a low-density treatment is presented that allows for low-density material to carry current while maintaining a stable temperature. This treatment is implemented in the Ares multiphysics code. Numerical modifications to the conventional vacuum treatment include an energy-conserving density floor, a modified averaging procedure to determine the thermal conductivity at the edge of adjacent zones, and a modified averaging procedure for determining the thermal conductivity in mixed zones that contain material from differing regions. Additionally, anomalous resistivity and Bohm diffusion models are implemented as simplified models for microphysics-induced enhancement of collisional transport. Importantly, the advantage of these various improvements are illustrated in a simple 1-D pulsed power target where the combined changes result in stable temperatures within the lower density regions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Spin density matrix elements in exclusive $\rho ^0$ meson muoproduction

We report on a measurement of Spin Density Matrix Elements (SDMEs) in hard exclusive $\rho ^0$ meson muoproduction at COMPASS using 160 GeV/c polarised μ + and μ – beams impinging on a liquid hydrogen target. The measurement covers the kinematic range 5.0 GeV/c 2 < W < 17.0 GeV/c 2 , 1.0 (GeV/c) 2 < $\mathrm{Q}$ 2 < 10.0 (GeV/c) 2 and 0.01 (GeV/c) 2 < $p_{\textrm{T}}^2$ < 0.5 (GeV/c) 2 . Here, W denotes the mass of the final hadronic system, $\mathrm{Q}$ 2 the virtuality of the exchanged photon, and $p_{\textrm{T}}$ the transverse momentum of the $\rho ^0$ meson with respect to the virtual-photon direction. The measured non-zero SDMEs for the transitions of transversely polarised virtual photons to longitudinally polarised vector mesons ($\gamma ^*_T \rightarrow V^{ }_L$) indicate a violation of s-channel helicity conservation. Additionally, we observe a dominant contribution of natural-parity-exchange transitions and a very small contribution of unnatural-parity-exchange transitions, which is compatible with zero within experimental uncertainties. The results provide important input for modelling Generalised Parton Distributions (GPDs). In particular, they may allow one to evaluate in a model-dependent way the role of parton helicity-flip GPDs in exclusive $\rho ^0$ production.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

NASA NTRS2008

Forebody and Inlet Design for the HIFiRE 2 Flight Test

A forebody and inlet have been designed for the HIFiRE 2 scramjet flight test. The test will explore the operating, performance, and stability characteristics of a simple hydrocarbon-fueled scramjet combustor as it transitions from dual-mode to scramjet-mode operation and during supersonic combustion at Mach 8+ flight conditions. Requirements for the compression system were derived from inlet starting and combustor inflow requirements as well as physical size constraints. The design process is described. A planar, fixed geometry, mixed compression concept was used to produce laterally uniform flow at the inlet entrance and a conservative amount of internal contraction with respect to inlet starting. A grid sensitivity study was performed so that important flow physics caused by three-dimensional shock boundary layer interactions could be captured with confidence. Results from low Mach number operability studies, nominal trajectory cases, and high dynamic pressure heat load cases are discussed. The forebody and inlet solutions provide information for on-going combustor calculations, mass capture across the trajectory for fuel system design, and surface heating rates for thermal/structural analysis. The design has a one freestream Mach number margin for inlet starting, exceeds the high Mach number combustor entrance pressure requirement, produces high quality flow at the inlet exit for all Mach numbers and vehicle attitudes in the design space, and fits inside the booster shroud.

Ferlemann, Paul G.↗

NASA NTRS2012

Gravity-Assist Mechanical Simulator for Outreach

There is no convenient way to demonstrate mechanically, as an outreach (or inreach) topic, the angular momentum trade-offs and the conservation of angular momentum associated with gravityassist interplanetary trajectories. The mechanical concepts that underlie gravity assist are often misunderstood or confused, possibly because there is no mechanical analog to it in everyday experience. The Gravity Assist Mech - anical Simulator is a hands-on solution to this longstanding technical communications challenge. Users intuitively grasp the concepts, meeting specific educational objectives. A manually spun wheel with high angular mass and low-friction bearings supplies momentum to an attached spherical neodymium magnet that represents a planet orbiting the Sun. A steel bearing ball following a trajectory across a glass plate above the wheel and magnet undergoes an elastic collision with the revolving magnet, illustrating the gravitational elastic collision between spacecraft and planet on a gravity-assist interplanetary trajectory. Manually supplying the angular momentum for the elastic collision, rather than observing an animation, intuitively conveys the concepts, meeting nine specific educational objectives. Many NASA and JPL interplanetary missions are enabled by the gravity-assist technique.

Doody, David F.↗

DOE OSTI2022

Hazma meets HERWIG4DM: precision gamma-ray, neutrino, and positron spectra for light dark matter

Herein we present a new open-source package, Hazma 2, that computes accurate spectra relevant for indirect dark matter searches for photon, neutrino, and positron production from vector-mediated dark matter annihilation and for spin-one dark matter decay. The tool bridges across the regimes of validity of two state of the art codes: Hazma 1, which provides an accurate description below hadronic resonances up to center-of-mass energies around 250 MeV, and Herwig4DM, which is based on vector meson dominance and measured form factors, and accurate well into the few GeV range. The applicability of the combined code extends to approximately 1.5 GeV, above which the number of final state hadrons off of which we individually compute the photon, neutrino, and positron yield grows exceedingly rapidly. We provide example branching ratios, particle spectra and conservative observational constraints from existing gamma-ray data for the well-motivated cases of decaying dark photon dark matter and vector-mediated fermionic dark matter annihilation. Finally, we compare our results to other existing codes at the boundaries of their respective ranges of applicability. Hazma 2 is freely available on GitHub athttps://github.com/LoganAMorrison/Hazma.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2020

Lipocalin Blc is a potential heme-binding protein

Lipocalins are a superfamily of functionally diverse proteins defined by a well-conserved tertiary structure despite variation in sequence. Lipocalins bind and transport small hydrophobic molecules in organisms of all kingdoms. However, there is still uncertainty regarding the function of some members of the family, including bacterial lipocalin Blc from Escherichia coli. Here, we present evidence that lipocalin Blc may be involved in heme binding, trans-periplasmic transport, or heme storage. This conclusion is supported by a cocrystal structure, mass-spectrometric data, absorption titration, and in silico analysis. Binding of heme is observed at low micromolar range with one-to-one ligand-to-protein stoichiometry. However, the absence of classical coordination to the iron atom leaves the possibility that the primary ligand of Blc is another tetrapyrrole.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2024

In tube condensation of low global warming potential refrigerants in an axial micro-fin aluminum tube

Environmental regulations have driven the development of refrigerants with low global warming potential (GWP). To design heat exchangers using these new refrigerants, data are needed concerning the heat transfer coefficient and pressure drop in two-phase flow. Another change is the increasing use of aluminum tubes rather than copper tubes to reduce heat exchanger cost. Hence, this study presents an experimental investigation of flow condensation using an expanded axial micro-fin aluminum tube with a fin-tip diameter of 5.96 mm. Here, the experiments included single compounds R-32, R-1234yf, and R-1234ze(E), zeotropic mixtures with low glide (R-454B), and zeotropic mixtures with high-glide (R-454C and R-455A). Experiments were conducted at condensation temperatures ranging from 40 °C to 50 °C, reduced pressures ranging from 0.21 to 0.55, and mass fluxes ranging from 150 to 350 kg/(m 2 s). Data obtained for these refrigerants constitute one of the first reports for high-glide refrigerants using axial micro-fin aluminum tubes. An evaluation of heat transfer degradation of zeotropic mixtures due to mass transfer resistance at the liquid/vapor interface is presented. This information can be used to design heat exchangers for next generation air conditioning and refrigeration systems.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2024

Exploration of mass splitting and muon/tau mixing parameters for an eV-scale sterile neutrino with IceCube

We present the first three-parameter fit to a 3+1 sterile neutrino model using 7.634 years of data from the IceCube Neutrino Observatory on $ν$ μ + $\overline{ν}$ μ charged-current interactions in the energy range 500–9976 GeV. Our analysis is sensitive to the mass-squared splitting between the heaviest and lightest mass state (Δm$^{2}_{41}$), the mixing matrix element connecting muon flavor to the fourth mass state (|U μ4 | 2 ), and the element connecting tau flavor to the fourth mass state (|U $\tau$4 | 2 ). Predicted propagation effects in matter enhance the signature through a resonance as atmospheric neutrinos from the Northern Hemisphere traverse the Earth to the IceCube detector at the South Pole. The remaining sterile neutrino matrix elements are left fixed, with |U e4 | 2 = 0 and δ 14 = 0, as they have a negligible effect, and δ 24 = π is set to give the most conservative limits. The result is consistent with the no-sterile neutrino hypothesis with a probability of 4.3%. Profiling the likelihood of each parameter yields the 90% confidence levels: 2.4eV 2 < Δm$^{2}_{41}$) < 9.6eV 2 , 0.0081< |U μ4 | 2 < 0.10, and |U $\tau$4 | 2 < 0.035, which narrows the allowed parameter-space for |U $\tau$4 | 2 . However, the primary result of this analysis is the first map of the 3+1 parameter space exploring the interdependence of Δm$^{2}_{41}$, |U μ4 | 2 , and |U $\tau$4 | 2 .

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2025

Lectures on statistical mechanics

Presented here is a transcription of the lecture notes from Professor Allan N. Kaufman’s graduate statistical mechanics course Physics 212A and 212B at the University of California Berkeley from the 1972–1973 academic year. 212A addressed equilibrium statistical mechanics with topics: fundamentals (micro-canonical and sub-canonical ensembles, adiabatic law and action conservation, fluctuations, pressure, and virial theorem), classical fluids and other systems (equation of state, deviations from ideality, virial coefficients and van der Waals potential, canonical ensemble and partition function, quasistatic evolution, grand-canonical ensemble and partition function, chemical potential, simple model of a phase transition, quantum virial expansion, numerical simulation of equations of state, and phase transition), chemical equilibrium (systems with multiple species and chemical reactions, law of mass action, Saha equation, chemical equilibrium including ionization and excited states), and long-range interactions (including Coulomb, dipole, and gravitational interactions, Debye–Hückel theory, and shielding). 212B addressed nonequilibrium statistical mechanics with topics: fundamentals (definitions: realizations, moments, characteristic function, and discrete variables), Brownian motion (Langevin equation, fluctuation–dissipation theorem, spatial diffusion, Boltzmann’s H-theorem), Liouville and Klimontovich equations, Landau equation (derivation, elaboration, and H-theorem, and irreversibility), Markov processes and Fokker–Planck equation (derivations of the Fokker–Planck equation and a master equation), linear response and transport theory (linear Boltzmann equation, linear response theory of Kubo and Mori, relation of entropy production to electrical conductivity, transport relations and coefficients, normal mode solutions of the transport equations, sketch of a generalized Langevin equation method for transport theory), and an introduction to nonequilibrium quantum statistical mechanics.

plasma dynamics↗

DOE OSTI2021

Ab initio benchmarks of neutrinoless double- β decay in light nuclei with a chiral Hamiltonian

Here, we report ab initio benchmark calculations of nuclear matrix elements (NMEs) for neutrinoless double-β (0νββ) decays in light nuclei with mass numbers ranging from A = 6 to A = 22. We use the transition operator derived from light-Majorana neutrino exchange and evaluate the NME with three different methods: two variants of in-medium similarity renormalization group (IMSRG) and importance-truncated no-core shell model (IT-NCSM). The same two plus three nucleon interaction from chiral effective field theory is employed, and both isospin-conserving (ΔT = 0) and isospin-changing (ΔT = 2) transitions are studied. We compare our resulting ground-state energies and NMEs to those of recent ab initio no-core shell model and coupled-cluster calculations, also with the same inputs. We show that the NMEs of ΔT = 0 transitions are in good agreement among all calculations, at the level of 10%. For ΔT = 2, relative deviations are more significant in some nuclei. The comparison with the exact IT-NCSM result allows us to analyze these cases in detail, and indicates the next steps toward improving the IMSRG-based approaches. The present study clearly demonstrates the power of consistent cross checks that are made possible by ab initio methodology. This capability is crucial for providing meaningful many-body uncertainties in the NMEs for the 0νββ decays in heavier candidate nuclei, where quasiexact benchmarks are not available.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2024

Search for the Z Boson Decay to τ τ μ μ in Proton-Proton Collisions at s = 13 TeV

The first search for the Z boson decay to τ τ μ μ at the CERN LHC is presented, based on data collected by the CMS experiment at the LHC in proton-proton collisions at a center-of-mass energy of 13 TeV and corresponding to an integrated luminosity of 138 fb − 1 . The data are compatible with the predicted background. For the first time, an upper limit at the 95% confidence level of 6.9 times the standard model expectation is placed on the ratio of the Z → τ τ μ μ to Z → 4 μ branching fractions. Limits are also placed on the six flavor-conserving four-lepton effective-field-theory operators involving two muons and two tau leptons, for the first time testing all such operators. © 2024 CERN, for the CMS Collaboration 2024 CERN

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2022

Bay Area Regional Energy: Network Integrated Commercial Retrofits (BRICR) Project. Final Report

The BRICR project applied large-scale building energy modeling concepts with the aim of reducing the cost of energy efficiency targeting, design, and project development, and measurement of energy savings for energy efficiency programs implemented by local governments that serve small and medium commercial buildings (SMB). The project leveraged the services and resources of existing local government energy programs serving disadvantaged and hard-to-reach SMB customers. In contrast to programs run by utilities, local government programs generally do not have direct access to energy billing records for an entire class of customers in a geographic area, which prior research demonstrated useful for large-scale building energy model baseline development and calibration. , However, local governments are rich in public records that offer important clues about physical attributes and uses that, along with behavior, determine energy use. Relying only on public records, BRICR demonstrated development of credible baseline energy models for 3,792 office, retail, and hotel buildings. Publicly disclosed annual energy use data from a local energy benchmarking program and anonymized data from the Building Performance Database, the nation’s largest dataset about energy-related characteristics of buildings, were utilized to validate and calibrate energy models via an innovative method comparing distributions of energy intensity by fuel type for portfolios of buildings of similar size, vintage, and use. Portfolio calibration does not provide certainty that an energy model fits an individual building; the method is useful when billing data is not accessible – a common situation for researchers, energy service providers and ESCOs, local governments, and any party other than a utility. A software component was developed, the BRICR gem, which automates simulation when relevant data is added or edited by the user to a file saved in the standardized BuildingSync XML schema for energy audit data. The component was demonstrated as a simplified means to generate a mass of energy models corresponding to public records containing basic attributes such as building scale, location, use, year built, and aspect ratio in combination with building energy code prototype data corresponding to use and vintage. The component was also demonstrated as a simplified means to automate energy simulation when attributes are revised; the intention was to enable iterative improvement of the baseline model and energy savings estimates for common energy conservation measures as users revise relevant attributes based on their observations. In the context of institutional change and uncertainty for the participating local government energy programs, 13 whole building retrofits were completed. Impacts were measured by applying the CalTRACK2.0 methods to standardize measurement of normalized metered energy consumption. The GRIDMeter methods of stratified sampling and individual load shape analysis were applied to adjust for impacts of the effect of COVID-19 on retrofitted buildings in the context of all local buildings of similar size and use. Excluding impacts of the pandemic, retrofitted buildings demonstrated between 1.6% and 25.1% reduction in energy use. The project contributed use cases and feedback that helped inform evolution of the software tools and data formats that were combined for the first time in the BRICR project.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

DOE OSTI2022

Spinning up the Surface: Evidence for Planetary Engulfment or Unexpected Angular Momentum Transport?

In this paper, we report the potential detection of a nonmonotonic radial rotation profile in a low-mass lower-luminosity giant star. For most low- and intermediate-mass stars, the rotation on the main sequence seems to be close to rigid. As these stars evolve into giants, the core contracts and the envelope expands, which should suggest a radial rotation profile with a fast core and a slower envelope and surface. KIC 9267654, however, seems to show a surface rotation rate that is faster than its bulk envelope rotation rate, in conflict with this simple angular momentum conservation argument. We improve the spectroscopic surface constraint, show that the pulsation frequencies are consistent with the previously published core and envelope rotation rates, and demonstrate that the star does not show strong chemical peculiarities. We discuss the evidence against any tidally interacting stellar companion. Finally, we discuss the possible origin of this unusual rotation profile, including the potential ingestion of a giant planet or unusual angular momentum transport by tidal inertial waves triggered by a close substellar companion, and encourage further observational and theoretical efforts.

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS2008

NEXT Ion Thruster Performance Dispersion Analyses

The NEXT ion thruster is a low specific mass, high performance thruster with a nominal throttling range of 0.5 to 7 kW. Numerous engineering model and one prototype model thrusters have been manufactured and tested. Of significant importance to propulsion system performance is thruster-to-thruster performance dispersions. This type of information can provide a bandwidth of expected performance variations both on a thruster and a component level. Knowledge of these dispersions can be used to more conservatively predict thruster service life capability and thruster performance for mission planning, facilitate future thruster performance comparisons, and verify power processor capabilities are compatible with the thruster design. This study compiles the test results of five engineering model thrusters and one flight-like thruster to determine unit-to-unit dispersions in thruster performance. Component level performance dispersion analyses will include discharge chamber voltages, currents, and losses; accelerator currents, electron backstreaming limits, and perveance limits; and neutralizer keeper and coupling voltages and the spot-to-plume mode transition flow rates. Thruster level performance dispersion analyses will include thrust efficiency.

Soulas, George C.↗