Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Computational Thermal Hydraulics of a High-Performance Low-Enriched-Uranium Annular Target for HFIR Irradiation

Molybdenum-99 has historically been generated via isolation from fissioned highly enriched uranium (HEU) targets. Here, this isotope is in high demand due to its daily use across the world in radiopharmaceutical medical procedures. The primary objective of this work was to design and analyze an experimental target assembly containing one low-enriched-uranium (LEU) annular target for irradiation at the High Flux Isotope Reactor (HFIR). Efforts included incorporating spatially dependent energy sources from neutron and gamma interactions, quantifying thermal contact conductance at material interfaces, performing grid-independent studies, comparing turbulence models, and simulating various steady-state and transient scenarios relevant for irradiation qualification and eventual insertion. These models provide velocity, pressure, and temperature distributions in both space and time. Such results enable the selection of an appropriate irradiation location, fission rate density, and flow-limiting orifice size and demonstrate compliance with HFIR safety requirements such that insertion into the reactor can be approved. This analysis shows that across all scenarios, wetted surface temperatures remain below the coolant saturation temperature with no net vapor formation in the coolant. In every scenario, all components stay below 30% of the aluminum 6061 melting temperature. Computational fluid dynamics and system-level models predict peak target temperatures that agree within 4%, though the predicted axial location of the peak differs by about 10% of the heated length due to differences in flow development length. These results de-risk the irradiation of LEU (annular targets) and strengthen a domestic, HEU-independent 99 Mo supply by providing important fuel performance data to form the foundation for a robust licensing basis.

Molybdenum-99↗
DOE OSTI2026

Characterization of the First Prototype of the L1K65n Differential-Output Charge-Sensitive Preamplifier ASIC for High-Performance, Low-Background HPGe Detector Readout

Next-generation neutrinoless double-beta (0νββ) decay searches require a large detector/isotope mass and very low radioactive backgrounds. The upcoming LEGEND-1000 experiment (Large Enriched Germanium Experiment for Neutrinoless double-beta Decay) constitute a ton-scale array of several hundred high-purity germanium (HPGe) detectors enriched in 76Ge, the isotope of interest. It aims to reach a sensitivity beyond 10 28 years on the 0νββ decay half-life of 76Ge, necessitating an order of magnitude reduction in background with respect to the state of the art. This will require the implementation of a dedicated application specific integrated circuit (ASIC) preamplifier that will significantly lower background contribution compared to the conventional low-mass front end (LMFE) employed in the Majorana Demonstrator and LEGEND-200 experiments while maintaining or improving energy resolution and other performance parameters. Features include a high (9 MeV) dynamic range with noise low enough to achieve a trigger threshold of <1 keV, a single power supply to reduce background-inducing cabling, and a differential output to maintain signal integrity over several meters of transmission line. The chip would be optimized to operate in liquid argon (87 K) and be able to do so reliably for ten years. Following on from an earlier 180-nm prototype, we have developed a differential-output charge-sensitive preamplifier ASIC fabricated in a 65-nm process, 1×2 mm in size, that addresses these needs. Here, we present recent results from the successful testing and characterization of the first version of this device.

ASIC↗
DOE OSTI2021

High-performance ECRH at W7-X: experience and perspectives

The second operation phase of W7-X (OP1.2) showed the potential of exclusively electron cyclotron resonance heating (ECRH)-sustained plasma operations in stellarators. Employing multi-pass ECRH scenario in the second harmonic O-mode (O2-ECRH), stationary densities of up to 1.4 × 10 20 m -3 could be achieved. This scenario also made stationary divertor detachment possible, which is a reactor-relevant scenario for power and particle exhaust. At high densities and with sufficiently high density gradients for an improved ion confinement, the coupling between the electrons and ions was strong enough to bring the ion temperature to values above 3 keV and to the neoclassical limit for some magnetic configurations, thus enabling to test the W7-X neoclassical optimization. The planned enhancement of the ECRH performance will enable to advance towards reactor-relevant beta values and to investigate their stability and confinement of fast particles, which is a priority goal of W7-X.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Designing high-performance superconductors with nanoparticle inclusions: Comparisons to strong pinning theory

One of the most promising routes for achieving high critical currents in superconductors is to incorporate dispersed, non-superconducting nanoparticles to control the dissipative motion of vortices. However, these inclusions reduce the overall superconducting volume and can strain the interlaying superconducting matrix, which can detrimentally reduce T c . Consequently, an optimal balance must be achieved between the nanoparticle density n p and size d. Determining this balance requires garnering a better understanding of vortex–nanoparticle interactions, described by strong pinning theory. Here, we map the dependence of the critical current on nanoparticle size and density in (Y 0.77 , Gd 0.23 )Ba 2 Cu 3 O 7-δ films in magnetic fields of up to 35 T and compare the trends to recent results from time-dependent Ginzburg–Landau simulations. We identify consistency between the field-dependent critical current J c (B) and expectations from strong pinning theory. Specifically, we find that J c ∝ B -α , where α decreases from 0.66 to 0.2 with increasing density of nanoparticles and increases roughly linearly with nanoparticle size d/ξ (normalized to the coherence length). At high fields, the critical current decays faster (~B -1 ), suggesting that each nanoparticle has captured a vortex. When nanoparticles capture more than one vortex, a small, high-field peak is expected in J c (B). Due to a spread in defect sizes, this novel peak effect remains unresolved here. Finally, we reveal that the dependence of the vortex creep rate S on nanoparticle size and density roughly mirrors that of α, and we compare our results to low-T nonlinearities in S(T) that are predicted by strong pinning theory.

36 MATERIALS SCIENCE↗
NASA NTRS1981

Quantitative separation of tetralin hydroperoxide from its decomposition products by high performance liquid chromatography

A method for the separation and analysis of tetralin hydroperoxide and its decomposition products by high pressure liquid chromatography has been developed. Elution with a single, mixed solvent from a micron-Porasil column was employed. Constant response factors (internal standard method) over large concentration ranges and reproducible retention parameters are reported.

Worstell, J. H.↗
NASA NTRS1991

Growth and characterization of high-performance photorefractive BaTiO3 crystals

Barium titanate has been used for many nonlinear optical applications primarily because it has high grain and high self-pumped phase conjugate reflectivities. However, barium titanate has had a relatively slow response time, and thus low sensitivity. Therefore, it has not been suited to real-time operations. In this report we will describe the modifications in crystal growth, doping, reduction, and poling that have produced barium titanate crystals with the fastest photorefractive response time reported to date, approximately 21 microseconds with a beam-coupling gain coefficient of 38.7 cm(exp -1) and the highest sensitivity reported to date of 3.44 cm(exp 3)/kJ. The sensitivity of these barium titanate crystals is comparable to or greater than other photorefractive oxides. We will show, for the first time, beam-coupling in barium titanate at video frame rates. We infer from response time measurements that barium titanate has a phonon limited mobility. Also, photorefractive response time measurements as a function of the crystallographic orientation and grating wave vector for our cobalt-doped oxygen reduced crystals indicate that their faster response time arise because of an increase in the free carrier lifetime.

Warde, C.↗
DOE OSTI2020

Design and Development of Low Weight, Titanium Aluminide Airfoils for High Performance Industrial Gas Turbines meeting 65% Combined Cycle Efficiency (Final Report)

This project funded under DOE-FOA-0001816 was performed with the intent of evaluating the potential of utilizing a low density, high specific strength Titanium Aluminide (TiAl) alloy in a large annulus last stage gas turbine blade with the intent of improving combined cycle gas turbine efficiency toward a goal of reaching 65% efficiency. The project consisted of identifying a potentially suitable TiAl material for manufacture of such a large blade by investment casting. This included estimation of design properties for the selected alloy, trade studies using a baseline design created for a nickel based alloy cast in the TiAl alloy to evaluate potential design changes required for the use of this material and optimization of a prototype design for the same baseline application using the selected TiAl alloy. Several rounds of optimization were completed with the intent of meeting the baseline design targets with a resulting design that showed at least equivalent performance in terms of creep, LCF/TMF, HCF and aerodynamic damping potential. While it was found that significant reductions in blade loading on the disk were possible, the design resulting from the optimization met most lifing targets at the baseline size, but showed a reduction in margins in some areas in comparison to the Ni-based baseline design. Additionally, it was found that the low strain tolerance of the TiAl alloy for temperatures at and below the operational temperature of the attachment resulted in marginal, although still acceptable, creep rupture performance of the design. Due to results indicating the reduced potential for increasing turbine annulus compared to expectations a Phase II award was not proposed and it is not recommended to pursue additional design optimization efforts until further material advances with TiAl materials are achieved.

03 NATURAL GAS↗
DOE OSTI2025

Scalable Solution-Processed Electrolyte Membranes with Optimized Microstructure for High-Performance Protonic Ceramic Electrochemical Cells

Proton-conducting electrochemical cells (PCECs) are promising for efficient hydrogen production, but achieving dense, uniform, thin electrolyte layers remains a key challenge, particularly for scalable fabrication. Here, we present a solution-processed deposition approach with a mechanistically optimized slurry for uniform electrolyte formation. By tailoring particle size distribution, solid loading, and solvent/additive balance, we regulated wetting behavior and evaporation kinetics of the electrolyte slurry to promote homogeneous electrolyte particle packing. These features facilitate tight grain boundary contact and early stage neck growth during sintering, eliminating residual porosity, and improving mechanical integrity. The resulting ∼15 μm thick electrolyte shows high density, strong electrode adhesion, and stable interfaces outperforming the previously reported spray-based fabricated electrolyte by about 31% at 600 °C in FC mode. Single cells deliver 0.962 W cm –2 at 600 °C in fuel cell mode and 1.31 A cm –2 at 1.3 V in electrolysis mode, maintaining robust performance over 100 h with negligible degradation (≤0.02% h –1 ) in each mode. Scale-up to 2.5 cm diameter substrates confirmed reproducible densification and geometric stability. This work demonstrates a cost-effective, scalable route where control over particle-fluid interactions and drying dynamics enables a superior electrolyte microstructure and high PCEC performance.

dense microstructure↗
DOE OSTI2023

High-performance multimode elastocaloric cooling system

Developing zero–global warming potential refrigerants has emerged as one area that helps address global climate change concerns. Various high-efficiency caloric cooling techniques meet this goal, but scaling them up to technologically meaningful performance remains challenging. We have developed an elastocaloric cooling system with a maximum cooling power of 260 watts and a maximum temperature span of 22.5 kelvin. These values are among the highest reported for any caloric cooling system. Its key feature is the compression of fatigue-resistant elastocaloric nitinol (NiTi) tubes configured in a versatile multimode heat exchange architecture, which allows the harnessing of both high delivered cooling power and large temperature spans. Our system shows that elastocaloric cooling, which only emerged 8 years ago, is a promising direction for commercializing caloric cooling.

Science & Technology - Other Topics↗
DOE OSTI2025

Optimizing Management of Persistent Data Structures in High-Performance Analytics

Large-scale data analytics workflows ingest massive input data into various data structures, including graphs and key-value datastores. These data structures undergo multiple transformations and computations and are typically reused in incremental and iterative analytics workflows. Persisting in-memory views of these data structures enables reusing them beyond the scope of a single program run while avoiding repetitive raw data ingestion overheads. Memory-mapped I/O enables persisting in-memory data structures without data serialization and deserialization overheads. However, memory-mapped I/O lacks the key feature of persisting consistent snapshots of these data structures for incremental ingestion and processing. The obstacles to efficient virtual memory snapshots using memory-mapped I/O include background writebacks outside the application’s control, and the significantly high storage footprint of such snapshots. To address these limitations, we present Privateer, a memory and storage management tool that enables storage-efficient virtual memory snapshotting while also optimizing snapshot I/O performance. Here, we integrated Privateer into Metall, a state-of-the-art persistent memory allocator for C++, and the Lightning Memory-Mapped Database (LMDB), a widely-used key-value datastore in data analytics and machine learning. Privateer optimized application performance by 1.22× when storing data structure snapshots to node-local storage, and up to 16.7× when storing snapshots to a parallel file system. Privateer also optimizes storage efficiency of incremental data structure snapshots by up to 11× using data deduplication and compression.

Computer science↗
NASA NTRS1979

High-performance wings with significant leading-edge thrust at supersonic speeds

A new class of curved-leading-edge wings with which significant levels of leading-edge thrust may be achieved at moderate supersonic speeds is suggested. A recent analysis of the factors limiting such leading-edge thrust has led to a new method for the prediction of attainable leading-edge thrust from subsonic through supersonic speeds for wings of arbitrary planform. Recent supersonic tests of a new wing shape, which largely meets design criteria given by the new prediction method, give evidence of significant levels of leading-edge thrust. The consequent unusually high levels of aerodynamic performance should renew interest in supersonic-cruise vehicle design in general and in cruise-speed selection in particular.

Robins, A. W.↗
DOE OSTI2022

Durable, High-Performance Unitized Reversible Fuel Cells Based on Proton Conductors

The main objective of this project was to develop robust, highly efficient, and economically viable H + -conducting membrane-based, unitized reversible fuel cell (H-URFC) technology for large-scale co-located energy storage and power generation. Another objective of this project is to gain a profound understanding of the degradation mechanisms of key stack materials and interfaces using various in situ, ex situ, and operando measurements guided by theoretical analysis. Nanostructured components will be integrated into cell design and the interfaces between electrodes and electrolyte will be modified with active bi-functional catalysts and protective coatings in order to achieve >70% roundtrip efficiency at 1 A/cm2 in both the fuel cell and the electrolysis modes. The end goal of the project is to advance the technology to the point that a university-industry collaboration can be established to scale up the technology for early adoption, and eventually enabling a pathway to large-scale energy storage that utilizes chemical storage and conversion for electrical grid balancing.

08 HYDROGEN↗
NASA NTRS2012

Enabling High Performance Instruments for Astronomy and Space Exploration and ALD

Benefits of ALD for NASA instruments and applications: a) Ultrathin, highly conformal, and uniform films over arbitrarily large surface area. b). High quality films (density, roughness, conductivity, etc.) . Angstrom level control of stoichiometry, interfaces, and surface properties: 1) Multilayer nanolaminates/nanocomposites. 2) Low temperature surface engineering. Flight applications enabled by ALD: a) Anti-reflective coatings/Mirrors/Filters/Optics for UV/Vis/NIR Detectors. b) Superconducting Films for Submillimeter Astronomy.

Anti?reflective coatings↗
DOE OSTI2023

Facile, Versatile and Stepwise Synthesis of High‐Performance Oligomer Acceptors for Stable Organic Solar Cells

Abstract Oligomer acceptors have recently emerged as promising photovoltaic materials for achieving high power conversion efficiency (PCE) and long‐term stability in organic solar cells (OSCs). However, the limited availability of diverse acceptors, resulting from the sole synthetic approach, has hindered their potential for future industrialization. In this study, we present a facile and effective stepwise approach that utilizes two consecutive Stille coupling reactions for the synthesis of oligomer acceptors. To demonstrate the feasibility of the novel approach, we successfully synthesize a trimer acceptor, Tri‐Y6‐OD, and further systematically investigate the impact of oligomerization on device performance and stability. The results reveal that this approach has significant advantages compared to the conventional method, including reduced formation of unwanted by‐products and lower difficulties in purification. Remarkably, the OSC based on PM6 : Tri‐Y6‐OD achieves an impressive PCE of 18.03 % and maintains 80 % of the initial PCE (T 80 ) for 1523 h under illumination, surpassing the performance of the corresponding small molecule acceptor Y6‐OD‐based device. Furthermore, the versatility of the synthetic strategy in obtaining diverse acceptors is further demonstrated. Overall, our findings provide a facile, versatile and stepwise way for synthesizing oligomer acceptors, thereby facilitating the development of stable and efficient OSCs.

Chemistry↗
DOE OSTI2022

Rational solvent molecule tuning for high-performance lithium metal battery electrolytes

Electrolyte engineering improved cycling of Li metal batteries and anode-free cells at low current densities; however, high-rate capability and tuning of ionic conduction in electrolytes are desirable yet less-studied. In this study, we design and synthesize a family of fluorinated-1,2-diethoxyethanes as electrolyte solvents. The position and amount of F atoms functionalized on 1,2-diethoxyethane were found to greatly affect electrolyte performance. Partially fluorinated, locally polar –CHF 2 is identified as the optimal group rather than fully fluorinated –CF 3 in common designs. Paired with 1.2 M lithium bis(fluorosulfonyl)imide, these developed single-salt-single-solvent electrolytes simultaneously enable high conductivity, low and stable overpotential, >99.5% Li||Cu half-cell efficiency (up to 99.9%, ±0.1% fluctuation) and fast activation (Li efficiency >99.3% within two cycles). Combined with high-voltage stability, these electrolytes achieve roughly 270 cycles in 50-μm-thin Li||high-loading-NMC811 full batteries and >140 cycles in fast-cycling Cu||microparticle-LiFePO 4 industrial pouch cells under realistic testing conditions. The correlation of Li + –solvent coordination, solvation environments and battery performance is investigated to understand structure–property relationships.

25 ENERGY STORAGE↗
DOE OSTI2025

Functionalized Porous Polymer Networks as High-Performance PFAS Adsorbents

Toxic per- and polyfluoroalkyl substances (PFAS) are now found in nearly every water source on the planet. Exposure to these molecules can have negative health consequences, but the low concentration of PFAS relative to other solutes in water makes their removal challenging. Adsorbents offer a promising treatment route, but often exhibit low selectivities and removal capacities, as well as slow kinetics. The performance in these metrics can be improved by chemically optimizing PFAS binding sites and maximizing PFAS-adsorbent interactions. To explore how to achieve this, a porous polymer network solid (PPN-6, also known as PAF-1) was postsynthetically modified with various chemical moieties capable of leveraging unique combinations of electrostatic, hydrogen-bonding, hydrophobic, and fluorophilic interactions with PFAS molecules. Batch adsorption experiments and computational studies revealed that electrostatic and hydrogen-bonding interactions drive short-chain PFAS adsorption, while hydrophobic and fluorophilic interactions improve long-chain PFAS adsorption. In complex water matrices, a combination of electrostatic and fluorophilic interactions led to the greatest total PFAS removal. The best-performing material, functionalized with a fluorinated alkylammonium (PPN-6-FNDMB), selectively adsorbs PFAS with high capacity (up to 4.0 mmol/g) and rapid kinetics (equilibrium reached in <30 s). Furthermore, PPN-6-FNDMB outperforms several commercial adsorbents, achieving near-complete removal of 21 different PFAS from a groundwater sample collected at a US Air Force base. The PFAS could subsequently be desorbed from PPN-6-FNDMB, concentrating them by a factor of over 50 times. The recycled PPN-6-FNDMB could then be reused with minimal losses in long-chain PFAS adsorption capacity over four cycles.

Pezoulas, Ethan R↗
DOE OSTI2020

Electrolyte design for LiF-rich solid–electrolyte interfaces to enable high-performance microsized alloy anodes for batteries

Lithium batteries with Si, Al or Bi microsized (>10 µm) particle anodes promise a high capacity, ease of production, low cost and low environmental impact, yet they suffer from fast degradation and a low Coulombic efficiency. In this paper, we demonstrate that a rationally designed electrolyte (2.0 M LiPF 6 in 1:1 v/v mixture of tetrahydrofuran and 2-methyltetrahydrofuran) enables 100 cycles of full cells that contain microsized Si, Al and Bi anodes with commercial LiFePO 4 and LiNi 0.8 Co 0.15 Al 0.05 O 2 cathodes. Alloy anodes with areal capacities of more than 2.5 mAh cm -2 achieved >300 cycles with a high initial Coulombic efficiency of >90% and average Coulombic efficiency of >99.9%. These improvements are facilitated by the formation of a high-modulus LiF–organic bilayer interphase, in which LiF possesses a high interfacial energy with the alloy anode to accommodate plastic deformation of the lithiated alloy during cycling. Lastly, this work provides a simple yet practical solution to current battery technology without any binder modification or special fabrication methods.

25 ENERGY STORAGE↗