SEARCH · Engineering Papers

Results for “error performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

All sources NASA NTRS DOE OSTI

NASA NTRS1990

Delivery performance of conventional aircraft by terminal-area, time-based air traffic control: A real-time simulation evaluation

A description and results are presented of a study to measure the performance and reaction of airline flight crews, in a full workload DC-9 cockpit, flying in a real-time simulation of an air traffic control (ATC) concept called Traffic Intelligence for the Management of Efficient Runway-scheduling (TIMER). Experimental objectives were to verify earlier fast-time TIMER time-delivery precision results and obtain data for the validation or refinement of existing computer models of pilot/airborne performance. Experimental data indicated a runway threshold, interarrival-time-error standard deviation in the range of 10.4 to 14.1 seconds. Other real-time system performance parameters measured include approach speeds, response time to controller turn instructions, bank angles employed, and ATC controller message delivery-time errors.

Credeur, Leonard↗

NASA NTRS2002

An Overview of Trajectory Design Operations for the Microwave Anisotropy Probe (MAP) Mission

The main science objective of the Microwave Anisotropy Probe (MAP) mission is to produce an accurate full-sky map of the cosmic microwave background temperature fluctuations - anisotropy. MAP will collect these measurements from a lissajous orbit about the Sun-Earth/Moon L2 Lagrange Point. The NASA Goddard Space Flight Center (GSFC) Flight Dynamics Analysis Branch provided mission analysis, maneuver planning and maneuver calibration for the MAP spacecraft. This paper will provide an overview of the MAP trajectory design, a summary of the maneuvers executed. Differences from the pre-launch nominal plan will also be discussed. During the MAP phasing loops, MAP performed three calibration maneuvers in order to characterize the performance of the primary sets of thrusters - +X, +Z, and -Z. The calibration maneuvers were designed to minimize their impact on the trajectory. Four maneuvers were performed to set up the gravity assist of the Moon - required to propel MAP out to its orbit about L2. These maneuvers were performed at the three phasing loop perigees and at 18 hours after the final perigee. It became necessary to alter some of the perigee maneuvers in order to shape the gravity assist. This shaping was done to help meet some mission goals. In particular, the gravity assist was changed slightly in order to remove lunar shadows in both the cruise out to L2 and in the first revolution about L2. This amounted to a change in the phasing loop AV of less than 1 m/s. After the gravity assist, two mid-course correction (MCC) maneuvers were performed in order to fine-tune the trajectory. MCC1 was used to clean up and errors which resulted from the gravity assist. MCC2 was performed in order to mitigate a large stationkeeping maneuver following a crucial instrument calibration period during the cruise phase. MAP executed it's first stationkeeping maneuver in January 16th and is ready for a second calibration period during late Winter / early Spring. Further information concerning subsequent stationkeeping maneuver will be added as they become available.

Cuevas, Osvaldo O.↗

NASA NTRS1976

Space shuttle navigation analysis

A detailed analysis of space shuttle navigation for each of the major mission phases is presented. A covariance analysis program for prelaunch IMU calibration and alignment for the orbital flight tests (OFT) is described, and a partial error budget is presented. The ascent, orbital operations and deorbit maneuver study considered GPS-aided inertial navigation in the Phase III GPS (1984+) time frame. The entry and landing study evaluated navigation performance for the OFT baseline system. Detailed error budgets and sensitivity analyses are provided for both the ascent and entry studies.

Jones, H. L.↗

NASA NTRS2005

SCPS-TP, TCP, and Rate-Based Protocol Evaluation

Tests were performed at Glenn Research Center to compare the performance of the Space Communications Protocol Standard Transport Protocol (SCPS TP, otherwise known as "TCP Tranquility") relative to other variants of TCP and to determine the implementation maturity level of these protocols, particularly for higher speeds. The testing was performed over reasonably high data rates of up to 100 Mbps with delays that are characteristic of near-planetary environments. The tests were run for a fixed packet size, but for variously errored environments. This report documents the testing performed to date.

Tran, Diepchi T.↗

NASA NTRS1991

Further evaluation of the constrained least squares electromagnetic compensation method

Technologies exist for construction of antennas with adaptive surfaces that can compensate for many of the larger distortions caused by thermal and gravitational forces. However, as the frequency and size of reflectors increase, the subtle surface errors become significant and degrade the overall electromagnetic performance. Electromagnetic (EM) compensation through an adaptive feed array offers means for mitigation of surface distortion effects. Implementation of EM compensation is investigated with the measured surface errors of the NASA 15 meter hoop/column reflector antenna. Computer simulations are presented for: (1) a hybrid EM compensation technique, and (2) evaluating the performance of a given EM compensation method when implemented with discretized weights.

Smith, William T.↗

NASA NTRS1978

Large Active Retrodirective Arrays for Space Applications

An active retrodirective array (ARA) electronically points a microwave beam back at the apparent source of an incident pilot signal. Retrodirectivity is the result of phase conjugation of the pilot signal received by each element of the array. The problem of supplying the correct phase reference to the phase conjugation circuit (PCC) associated with each element of the array is solved by central phasing. By eliminating the need for structural rigidity, central phasing confers a decisive advantage on ARA's as large spaceborne antennas. A new form of central phasing suitable for very large arrays is described. ARA's may easily be modified to serve both as transmitting and receiving arrays simultaneously. Two new kinds of exact, frequency translating PCC's are described. Such PCC's provide the ARA with input-output isolation and freedom from squint. The pointing errors caused by the radial and transverse components of the ARA's velocity, by the propagation medium, and by multipath are discussed. A two element ARA breadboard was built and tested at JPL. Its performance is limited primarily by multipath induced errors.

Chernoff, R. C.↗

NASA NTRS2005

First Test of Fan Active Noise Control (ANC) Completed

With the advent of ultrahigh-bypass engines, the space available for passive acoustic treatment is becoming more limited, whereas noise regulations are becoming more stringent. Active noise control (ANC) holds promise as a solution to this problem. It uses secondary (added) noise sources to reduce or eliminate the offending noise radiation. The first active noise control test on the low-speed fan test bed was a General Electric Company system designed to control either the exhaust or inlet fan tone. This system consists of a "ring source," an induct array of error microphones, and a control computer. Fan tone noise propagates in a duct in the form of spinning waves. These waves are detected by the microphone array, and the computer identifies their spinning structure. The computer then controls the "ring source" to generate waves that have the same spinning structure and amplitude, but 180 out of phase with the fan noise. This computer generated tone cancels the fan tone before it radiates from the duct and is heard in the far field. The "ring source" used in these tests is a cylindrical array of 16 flat-plate acoustic radiators that are driven by thin piezoceramic sheets bonded to their back surfaces. The resulting source can produce spinning waves up to mode 7 at levels high enough to cancel the fan tone. The control software is flexible enough to work on spinning mode orders from -6 to 6. In this test, the fan was configured to produce a tone of order 6. The complete modal (spinning and radial) structure of the tones was measured with two builtin sets of rotating microphone rakes. These rakes provide a measurement of the system performance independent from the control system error microphones. In addition, the far-field noise was measured with a semicircular array of 28 microphones. This test represents the first in a series of tests that demonstrate different active noise control concepts, each on a progressively more complicated modal structure. The tests are in preparation for a demonstration on a flight-type engine.

Source record↗

NASA NTRS1966

Gemini orbital tracking.

Simulation testing pilot performance in orbiting Gemini spacecraft based on tracking rate errors and fuel consumption

ASTRONAUT PERFORMANCE↗

NASA NTRS1978

Bursty channel errors and the Viterbi decoder

Recent applications have developed for spread spectrum communications, hardware data transfer, high rate digital systems, etc. that use channels for which errors tend to occur in short bursts in addition to those at random, i.e., compound channels. Viterbi decoding algorithms are generally very good for random error channels but are not as efficient for burst errors or for compound channels. This paper presents the results of a computer simulation study of the performance of various Viterbi decoders when receiving data corrupted with burst and random errors on the same channel. Simulations were performed using hard-decision CPSK.

Ingels, F.↗

NASA NTRS1991

Compressed/reconstructed test images for CRAF/Cassini

A set of compressed, then reconstructed, test images submitted to the Comet Rendezvous Asteroid Flyby (CRAF)/Cassini project is presented as part of its evaluation of near lossless high compression algorithms for representing image data. A total of seven test image files were provided by the project. The seven test images were compressed, then reconstructed with high quality (root mean square error of approximately one or two gray levels on an 8 bit gray scale), using discrete cosine transforms or Hadamard transforms and efficient entropy coders. The resulting compression ratios varied from about 2:1 to about 10:1, depending on the activity or randomness in the source image. This was accomplished without any special effort to optimize the quantizer or to introduce special postprocessing to filter the reconstruction errors. A more complete set of measurements, showing the relative performance of the compression algorithms over a wide range of compression ratios and reconstruction errors, shows that additional compression is possible at a small sacrifice in fidelity.

Dolinar, S.↗

NASA NTRS1984

Performance of OOK and low-order PPM modulations in optical communications when using APD-based receivers

The paper computes direct detection laser communications receiver performance when using avalanche photodiode (APD) detectors. The performances are compared in terms of bit error probability vs average signal required per bit when the transmitter uses either on-off keying (OOK) or low-order PPM formats. It is shown that QPPM requires 3 dB less signal than OOK, while BPPM requires the same or slightly more than OOK for the same performance. Optimum APD gain values range from 200 to 400. When using QPPM, k(eff) = 0.006, and optimum gain, 60 signal counts/bit are required at 500 Mbits/s for a 0.000001 bit error probability. It is concluded that QPPM may be an attractive signaling format for some fiber or free space laser communication applications.

Abshire, J. B.↗

NASA NTRS1979

Effect of cursor characteristics on pilots' tracking performance on a cathode-ray tube in dynamic simulation

The effects of cursor configuration, size, and orientation on the performance of 11 commercial airline pilots were investigated in a difficult compensatory tracking task in a moving-base aircraft simulator. Three levels of congruent cab motion (0, 1, and 2 times the visual motion) were superimposed on the tracking task. Data analysis of the mean tracking error scores revealed no significant effects of cursor size, orientation, or configuration on pilots' tracking performance. Mean tracking error did not significantly differ between the three levels of motion for the conditions with a single dot as the cursor. However, for the dotted and solid line cursors, tracking error significantly decreased from the no motion condition to the motion conditions. The addition of simulator motion significantly reduced tracking error for large cursors, but not for small ones such as a single dot

Junge, M. K.↗

NASA NTRS2012

Piezocomposite Actuator Arrays for Correcting and Controlling Wavefront Error in Reflectors

Three reflectors have been developed and tested to assess the performance of a distributed network of piezocomposite actuators for correcting thermal deformations and total wave-front error. The primary testbed article is an active composite reflector, composed of a spherically curved panel with a graphite face sheet and aluminum honeycomb core composite, and then augmented with a network of 90 distributed piezoelectric composite actuators. The piezoelectric actuator system may be used for correcting as-built residual shape errors, and for controlling low-order, thermally-induced quasi-static distortions of the panel. In this study, thermally-induced surface deformations of 1 to 5 microns were deliberately introduced onto the reflector, then measured using a speckle holography interferometer system. The reflector surface figure was subsequently corrected to a tolerance of 50 nm using the actuators embedded in the reflector's back face sheet. Two additional test articles were constructed: a borosilicate at window at 150 mm diameter with 18 actuators bonded to the back surface; and a direct metal laser sintered reflector with spherical curvature, 230 mm diameter, and 12 actuators bonded to the back surface. In the case of the glass reflector, absolute measurements were performed with an interferometer and the absolute surface was corrected. These test articles were evaluated to determine their absolute surface control capabilities, as well as to assess a multiphysics modeling effort developed under this program for the prediction of active reflector response. This paper will describe the design, construction, and testing of active reflector systems under thermal loads, and subsequent correction of surface shape via distributed peizeoelctric actuation.

piezoelectric actuation↗

NASA NTRS1978

A comparative study of optimum and suboptimum direct-detection laser ranging receivers

A summary of previously proposed receiver strategies for direct-detection laser ranging receivers is presented. Computer simulations are used to compare performance of candidate implementation strategies in the 1- to 100-photoelectron region. Under the condition of no background radiation, the maximum-likelihood and minimum mean-square error estimators were found to give the same performance for both bell-shaped and rectangular optical-pulse shapes. For signal energies greater than 100 photoelectrons, the root-mean-square range error is shown to decrease as Q to the -1/2 power for bell-shaped pulses and Q to the -1 power for rectangular pulses, where Q represents the average pulse energy. Of several receiver implementations presented, the matched-filter peak detector was found to be preferable. A similar configuration, using a constant-fraction discriminator, exhibited a signal-level dependent time bias.

Abshire, J. B.↗

NASA NTRS2012

Common-Path Wavefront Sensing for Advanced Coronagraphs

Imaging of faint companions around nearby stars is not limited by either intrinsic resolution of a coronagraph/telescope system, nor is it strictly photon limited. Typically, it is both the magnitude and temporal variation of small phase and amplitude errors imparted to the electric field by elements in the optical system which will limit ultimate performance. Adaptive optics systems, particularly those with multiple deformable mirrors, can remove these errors, but they need to be sensed in the final image plane. If the sensing system is before the final image plane, which is typical for most systems, then the non-common path optics between the wavefront sensor and science image plane will lead to un-sensed errors. However, a new generation of high-performance coronagraphs naturally lend themselves to wavefront sensing in the final image plane. These coronagraphs and the wavefront sensing will be discussed, as well as plans for demonstrating this with a high-contrast system on the ground. Such a system will be a key system-level proof for a future space-based coronagraph mission, which will also be discussed.

adaptive optics↗

NASA NTRS2008

Impact of Pilot Delay and Non-Responsiveness on the Safety Performance of Airborne Separation

Assessing the safety effects of prediction errors and uncertainty on automationsupported functions in the Next Generation Air Transportation System concept of operations is of foremost importance, particularly safety critical functions such as separation that involve human decision-making. Both ground-based and airborne, the automation of separation functions must be designed to account for, and mitigate the impact of, information uncertainty and varying human response. This paper describes an experiment that addresses the potential impact of operator delay when interacting with separation support systems. In this study, we evaluated an airborne separation capability operated by a simulated pilot. The experimental runs are part of the Safety Performance of Airborne Separation (SPAS) experiment suite that examines the safety implications of prediction errors and system uncertainties on airborne separation assistance systems. Pilot actions required by the airborne separation automation to resolve traffic conflicts were delayed within a wide range, varying from five to 240 seconds while a percentage of randomly selected pilots were programmed to completely miss the conflict alerts and therefore take no action. Results indicate that the strategicAirborne Separation Assistance System (ASAS) functions exercised in the experiment can sustain pilot response delays of up to 90 seconds and more, depending on the traffic density. However, when pilots or operators fail to respond to conflict alerts the safety effects are substantial, particularly at higher traffic densities.

Consiglio, Maria↗

NASA NTRS1995

Effect Of Transition Density On Performance Of A DTTL

One estimates minimum transition density needed to limit symbol-error rate. Theoretical calculations and accompanying computer simulations provide numerical basis for specification of minimum data-transition density needed for adequate performance of radio receiver processing noisy signal containing non-return-to-zero (NRZ) stream of data symbols (bits). By use of digital-data-transition-tracking loop (DTTL), receiver strives to synchronize operation with data symbols. Performance of receiver in terms of ability to keep symbol-error rate (SER) in output of receiver below specified level depends on symbol signal-to-noise ratio (SSNR) of incoming signal and on degree of synchronization. Ability of DTTL to maintain synchronization depends partly on SSNR and partly on data-transition density.

Nguyen, Tien M.↗

NASA NTRS1985

Fine guidance sensor design optimization for Space Infrared Telescope Facility (SIRTF)

The present paper is concerned with the general issues of design optimization of a staring mosaic sensor for guide-star tracking, taking into account the choice of the proper interpolation algorithm. It was found that the final choice of algorithm depends on the severity of the positional accuracy requirement and the expected variation in the blur spot shape. The considered track algorithms estimate the position either of the peak or of the centroid of the image of a point source. Attention is given to aspects of problem definition, the total effect of error sources on algorithm accuracy, a parametric analysis of performance behavior, Monte Carlo results, and the design of the SIRTF Fine Guidance Sensor (FGS). The algorithm error, the signal-to-noise error, and the nonuniformity error are examined.

Grossman, S. B.↗