Results for “energy optimization” — Page 59

NASA NTRS1997

Chaos: Understanding and Controlling Laser Instability

In order to characterize the behavior of tunable diode lasers (TDL), the first step in the project involved the redesign of the TDL system here at the University of Tennessee Molecular Systems Laboratory (UTMSL). Having made these changes it was next necessary to optimize the new optical system. This involved the fine adjustments to the optical components, particularly in the monochromator, to minimize the aberrations of coma and astigmatism and to assure that the energy from the beam is focused properly on the detector element. The next step involved the taking of preliminary data. We were then ready for the analysis of the preliminary data. This required the development of computer programs that use mathematical techniques to look for signatures of chaos. Commercial programs were also employed. We discovered some indication of high dimensional chaos, but were hampered by the low sample rate of 200 KSPS (kilosamples/sec) and even more by our sample size of 1024 (1K) data points. These limitations were expected and we added a high speed data acquisition board. We incorporated into the system a computer with a 40 MSPS (million samples/sec) data acquisition board. This board can also capture 64K of data points so that were then able to perform the more accurate tests for chaos. The results were dramatic and compelling, we had demonstrated that the lead salt diode laser had a chaotic frequency output. Having identified the chaotic character in our TDL data, we proceeded to stage two as outlined in our original proposal. This required the use of an Occasional Proportional Feedback (OPF) controller to facilitate the control and stabilization of the TDL system output. The controller was designed and fabricated at GSFC and debugged in our laboratories. After some trial and error efforts, we achieved chaos control of the frequency emissions of the laser. The two publications appended to this introduction detail the entire project and its results.

Blass, William E.↗

NASA NTRS2005

Performance and Mass Modeling Subtleties in Closed-Brayton-Cycle Space Power Systems

Contents include the following: 1. Closed-Brayton-cycle (CBC) thermal energy conversion is one available option for future spacecraft and surface systems. 2. Brayton system conceptual designs for milliwatt to megawatt power converters have been developed 3. Numerous features affect overall optimized power conversion system performance: Turbomachinery efficiency. Heat exchanger effectiveness. Working-fluid composition. Cycle temperatures and pressures.

Barrett, Michael J.↗

NASA NTRS2009

Design Evolution and Verification of the A-3 Chemical Steam Generator

Following is an overview of the Chemical Steam Generator system selected to provide vacuum conditions for a new altitude test facility, the A-3 Test Stand at Stennis Space Center (SSC) in Bay St. Louis, MS. A-3 will serve as NASA s primary facility for altitude testing of the J-2X rocket engine, to be used as the primary propulsion device for the upper stages of the Ares launch vehicles. The Chemical Steam Generators (CSGs) will produce vacuum conditions in the test cell through the production and subsequent supersonic ejection of steam into a diffuser downstream of the J-2X engine nozzle exit. The Chemical Steam Generators chosen have a rich heritage of operation at rocket engine altitude test facilities since the days of the Apollo program and are still in use at NASA White Sands Test Facility (WSTF) in New Mexico. The generators at WSTF have been modified to a degree, but are still very close to the heritage design. The intent for the A-3 implementation is to maintain this heritage design as much as possible, making minimal updates only where necessary to substitute for obsolete parts and to increase reliability. Reliability improvements are especially desired because the proposed system will require 27 generators, which is nine times the largest system installed in the 1960s. Improvements were suggested by the original design firm, Reaction Motors, by NASA SSC and NASA WSTF engineers, and by the A-3 test stand design contractor, Jacobs Technology, Inc. (JTI). This paper describes the range of improvements made to the design to date, starting with the heritage generator and the minor modifications made over time at WSTF, to the modernized configuration which will be used at A-3. The paper will discuss NASA s investment in modifications to SSC s E-2 test facility fire a full-scale Chemical Steam Generator in advance of the larger steam system installation at A-3. Risk mitigation testing will be performed in early 2009 at this test facility to verify that the CSGs operate as expected. The generator which will undergo this testing is of the most recent A-3 configuration, and will be instrumented far in excess of what is normally required for operation. The extra data will allow for easier troubleshooting and more complete knowledge of expected generator performance. In addition, the early testing will give SSC personnel experience in operating the CSG systems, which will expedite the process of installation and activation at A-3. Each Chemical Steam Generator is supported by a complement of valves, instruments, and flow control devices, with the entire assembly called a "module." The generators will be installed in groups of three, historically called "units". A module is so called because of its modular ability to be replaced or serviced without disturbing the other two modules installed on the same unit. A module is pictured in Figure 1, shown with its generator secured by white bands in its shipping (vs. installed) configuration. The heritage system at WSTF is composed of a single unit (three generator modules), pictured in Figure 2 as it was installed in 1965. In contrast, A-3 will have nine units operating in parallel to achieve vacuum conditions appropriate for testing the J-2X engine. Each of the combustors operates in two modes and achieves the so-called "full-steam" mode after all three of its stages ignite. Ignition of the first stage is achieved by exciting a spark plug; the second stage and main stage are lit by the flame front of the previous stage. The main stage burns approximately 97% of the total propellant flow and uses the heat energy to vaporize water into superheated steam. While the main stage remains unlit, the combustor is in so-called "idle" mode. In the WSTF system, this idle mode is not optimized for water usage, and does not need to be, as the water is pumped from a large reservoir. The water supply at A-3 will be contained in tanks with finite volume, so water optimization is preferred for the modnized configuration. Multiple solutions for this issue have been proposed, with the leading concept being a change to the operational definition of "idle mode," with the generator running in a lower heat flux condition.

Kirchner, Casey K.↗

NASA NTRS2014

Design and Control of Modular Spine-Like Tensegrity Structures

We present a methodology enabled by the NASA Tensegrity Robotics Toolkit (NTRT) for the rapid structural design of tensegrity robots in simulation and an approach for developing control systems using central pattern generators, local impedance controllers, and parameter optimization techniques to determine effective locomotion strategies for the robot. Biomimetic tensegrity structures provide advantageous properties to robotic locomotion and manipulation tasks, such as their adaptability and force distribution properties, flexibility, energy efficiency, and access to extreme terrains. While strides have been made in designing insightful static biotensegrity structures, gaining a clear understanding of how a particular structure can efficiently move has been an open problem. The tools in the NTRT enable the rapid exploration of the dynamics of a given morphology, and the links between structure, controllability, and resulting gait efficiency. To highlight the effectiveness of the NTRT at this exploration of morphology and control, we will provide examples from the designs and locomotion of four different modular spine-like tensegrity robots.

Modular↗

NASA NTRS2017

Magnetic Field Sensing with 4H SiC Diodes: N vs P Implantation

We explore the magnetic sensing capabilities of two 4H-SiC n+p diodes fabricated by NASA Glenn which only differ in the implanted ion species, nitrogen and phosphorus, and the implant activation annealing time. We use low- and high-field electrically detected magnetic resonance (EDMR) to investigate the defect structure used to sense magnetic fields as well as to evaluate the sensitivity. In addition, we expose these devices to high energy electron radiation to evaluate the defect sensing capability in a harsh radiation environment. The results from this work will allow us to tailor our processing methods to design a more optimal 4H-SiC pn diode for magnetic field sensing in harsh environments.

Cochrane, Corey J.↗

NASA NTRS1991

Tuned optimization of extended reacting acoustic liners

A finite element Galerkin formulation was employed to study the optimum attenuation and reflection characteristics of acoustic waves propagating in tw0 dimensional straight ducts with extended reacting absorbing walls without a mean flow. The reflection and transmission of acoustic energy at the entrance and the exit of the duct were determined by coupling the finite element solutions in the absorbing portion of the duct to the eigenfunctions of an infinite, uniform, hard wall duct. In the frequency range where the duct height and acoustic wave length are nearly equal, power attenuation contours were examined to determine conditions for minimizing acoustic transmission through the duct. The extended reacting liners were found to significantly minimize the reflective characteristics of the duct rather than to increase absorption in the liner. Thus, extended reacting wall liner properties can be theoretically chosen to yield large impedance mismatches in an open straight duct.

Baumeister, Kenneth J.↗

NASA NTRSDate not supplied

Advancement of Extreme Environment Additively Manufactured Alloys for Next Generation Space Propulsion Applications

The National Aeronautics and Space Administration (NASA) has been involved in the development and maturation of metal additive manufacturing (AM) for space applications since the late 2000’s. Several efforts focused on the understanding of AM processes through material characterization and testing, standards development, component fabrication, and infusion into propulsion development and flight applications. NASA matured commonly used aerospace alloys from various alloy families (Nickel, Copper, Stainless and Steel, Aluminum, and Titanium-based) through detailed AM process and heat treatment characterization, in addition to mechanical and thermophysical testing. While these alloys are actively used in many propulsion applications, there is a need for ongoing AM optimized alloys using integrated computational materials engineering (ICME) and process development for high performance applications. The applications targeted are liquid rocket engines; advanced propulsion systems; and in-space propulsion with high heat fluxes, high pressure, and/or that use propellants that can degrade alloys (e.g., hydrogen). This paper highlights the characterization and physical properties of the more common AM alloys using laser powder bed fusion (L-PBF) and laser powder directed energy deposition (LP-DED) processes. Additionally, this paper discusses some of the ongoing novel alloy development and maturation using AM for use in these harsh environments, such as GRCop-42, GRCop-84, NASA HR-1, GRX-810, and C-103. The results from these processes demonstrated that AM could enable rapid development and ongoing efforts for optimized alloys using ICME, yielding higher performances. These alloys have undergone modeling, fundamental metallurgical evaluations, heat treatment studies, detailed microstructure characterization, and mechanical testing campaigns. This, combined with direct application-specific component fabrication and hot-fire testing, enabled the increase of the Technology Readiness Level (TRL) through high duty-cycle testing. A background and overview of these novel AM-enabled alloys and AM processing developments including metallurgical and mechanical property studies is presented here. The latest advancement in the parallel component development and hot-fire testing and future developments for these alloys is also discussed.

Additive Manufacturing↗

NASA NTRS1981

Adapting magnetoelectrostatic containment to inert gas thrusters

Two different types of 12 cm magnetoelectrostatic containment (MESC) ion thrusters have been adapted to argon-xenon operation. Discharge chamber optimization produced excellent performance with both the hexagonal and hemispherical shaped thrusters. The hemispherical thruster design yielded the best performance, ionizing 75 to 96 percent of the xenon propellant with a discharge energy consumption rate of 185 to 320 eV/ion. Argon operation of the same thruster achieved 60 to 80 percent propellant ionization at 215 to 370 eV/ion.

Ramsey, W. D.↗

NASA NTRS1987

Optimal trajectories for aeroassisted, coplanar orbital transfer

Classical and minimax optimal control problems arising in the study of aeroassisted coplanar orbit transfer from a high planetary orbit to a low one are considered. Attention is given to (1) the minimization of the energy required for the maneuver; (2) minimization of the time integral of the heating rate; (3) minimization of the time of flight during the atmospheric portion of the trajectory; (4) maximization of the time of flight during the atmospheric portion of the trajectory; (5) minimization of the time integral of the path inclination; and (6) minimization of the sum of the squares of the entry and exit path inclinations.

Miele, A.↗

NASA NTRS1991

Minimum-weight design of laminated composite plates for postbuckling performance

Minimum-weight design of simply-supported, symmetrically laminated, thin, rectangular, specially orthotropic laminated plates for buckling and postbuckling strength is investigated. The postbuckling analysis is based on an Marguerre-type energy method. The failure load of laminates is calculated by the maximum strain failure criterion based on the in-plane strains. Design variables are individual layer thicknesses with specified fiber orientations. Optimization with discrete valued design is achieved by introducing additional penalty terms to the regular pseudoobjective function of sequential unconstrained minimization technique. The proposed optimization technique is applied to the design of rectangular laminates with various aspect ratios loaded by axial compressive loads.

Shin, Dong KU↗

NASA NTRS1993

Procedures for analysis of debris relative to Space Shuttle systems

Debris samples collected from various Space Shuttle systems have been submitted to the Microchemical Analysis Branch. This investigation was initiated to develop optimal techniques for the analysis of debris. Optical microscopy provides information about the morphology and size of crystallites, particle sizes, amorphous phases, glass phases, and poorly crystallized materials. Scanning electron microscopy with energy dispersive spectrometry is utilized for information on surface morphology and qualitative elemental content of debris. Analytical electron microscopy with wavelength dispersive spectrometry provides information on the quantitative elemental content of debris.

Kim, Hae Soo↗

NASA NTRS1999

Polycapillary X-Ray Optics for X-Ray Astronomy

High-energy x-ray spectrometry from astronomical sources is difficult due to low flux rates and high background. Polycapillary x-ray optics can be used to increase the signal-to-noise ratio by focusing photons onto a small energy dispersive detector. Two optics, both designed for x-ray astronomy, have been built and tested as collimating optics with a microfocus x-ray source for x-ray energies up to 70 keV and as focusing optics with parallel x-rays up to 50 keV. Results from these tests show that polycapillary x-ray optics have transmission efficiencies ranging from 5% to 40% and signal gains ranging from 5 to over 100 for energies up to 50 keV. Furthermore the results show that these optics have potential for use up to 100 keV. The experimental results as well as simulations for the measured and for optimized optics will be discussed.

Russell, C. H.↗

NASA NTRS2004

Electron-Spin Filters Based on the Rashba Effect

Semiconductor electron-spin filters of a proposed type would be based on the Rashba effect, which is described briefly below. Electron-spin filters more precisely, sources of spin-polarized electron currents have been sought for research on, and development of, the emerging technological discipline of spintronics (spin-based electronics). There have been a number of successful demonstrations of injection of spin-polarized electrons from diluted magnetic semiconductors and from ferromagnetic metals into nonmagnetic semiconductors. In contrast, a device according to the proposal would be made from nonmagnetic semiconductor materials and would function without an applied magnetic field. The Rashba effect, named after one of its discoverers, is an energy splitting, of what would otherwise be degenerate quantum states, caused by a spin-orbit interaction in conjunction with a structural-inversion asymmetry in the presence of interfacial electric fields in a semiconductor heterostructure. The magnitude of the energy split is proportional to the electron wave number. The present proposal evolved from recent theoretical studies that suggested the possibility of devices in which electron energy states would be split by the Rashba effect and spin-polarized currents would be extracted by resonant quantum-mechanical tunneling. Accordingly, a device according to the proposal would be denoted an asymmetric resonant interband tunneling diode [a-RITD]. An a-RITD could be implemented in a variety of forms, the form favored in the proposal being a double-barrier heterostructure containing an asymmetric quantum well. It is envisioned that a-RITDs would be designed and fabricated in the InAs/GaSb/AlSb material system for several reasons: Heterostructures in this material system are strong candidates for pronounced Rashba spin splitting because InAs and GaSb exhibit large spin-orbit interactions and because both InAs and GaSb would be available for the construction of highly asymmetric quantum wells. This mate-rial system affords a variety of energy-band alignments that can be exploited to obtain resonant tunneling and other desired effects. The no-common-atom InAs/GaSb and InAs/AlSb interfaces would present opportunities for engineering interface potentials for optimizing Rashba spin splitting.

Ting, David Z.-Y.↗

NASA NTRSDate not supplied

NASA’s Space Launch System: Building A Capability for Science and Exploration

NASA’s Space Launch System, designed for human exploration of deep space and offering enabling benefits for a variety of science missions, is entering the final stages of preparation for its first launch, while simultaneously making progress toward future missions. SLS offers robust payload mass, volume, and characteristic energy that can be used not only for human exploration but for a variety of science missions, including probes to the outer solar system and beyond. In addition, while the vehicle is optimized to be a super-heavy lifter for lunar orbit as a staging area for the lunar surface or Mars, the addition of commercially available propulsion systems as third and/or fourth stages allows SLS to deliver unmatched performance for ultra-high C3 missions. Studies show that while the baseline SLS Block 2 vehicle can deliver about 8 t directly to the Jovian system at a C3 of 83, the addition of a Centaur upper stage would raise that mass to more than 15 t. The New Horizons spacecraft, with mass less than 0.5 t, launched toward Pluto with a record C3 of 158 km2/sec2. By comparison, an SLS Block 2 with an Orion 30B and Star 48BV payload stages could launch equivalent mass to a C3 more than double that of the New Horizons launch. (While the study has been conducted based on contemporary cryo stages and solid stages, this analysis provides real-world data for the range of performance this capability enables even as the specific stages available evolve.) Studies have shown it may be possible to reach 80-90 AU within a decade. The initial Block 1 vehicle for the first launch, Artemis I, is completely manufactured and all the elements are at NASA’s Kennedy Space Center (KSC) with the exception of the core stage, and manufacturing is in progress for the next several flights. Following the completion of the Green Run test series at NASA’s Stennis Space Center, the Artemis I core stage will be refurbished and delivered to KSC for stacking for launch in the second half of 2021. With the Artemis I vehicle fully manufactured and assembly of solid rocket boosters beginning, NASA and its industry partners have made significant progress manufacturing successive vehicles. Hardware for the next two launches is currently in production. NASA is committed to SLS as a key component of its launch architecture. Agency planning manifests outline the launch vehicle’s role in human lunar exploration over the next decade as it moves from its Block1 configuration to its intermediate Block 1B configuration and its ultimate Block 2 configuration.In addition, NASA has issued contracts with prime contractors for SLS hardware for delivery well into the 2030s.

Robert W. Stough↗

NASA NTRS2021

Utilizing local phase transformation strengthening for nickel-based superalloys

Almost 75 years of research has been devoted to producing superalloys capable of higher operating temperatures in jet turbine engines, and there is an ongoing need to increase operating temperature further. Here, a new disk Nickel-base superalloy is designed to take advantage of strengthening atomic-scale dynamic complexions. This local phase transformation strengthening provides the alloy with a three times improvement in creep strength over similar disk superalloys and comparable strength to a single crystal blade alloy at 760 °C. Ultra-high-resolution chemical mapping reveals that the improvement in creep strength is a result of atomic-scale η (D024) and χ (D019) formation along superlattice stacking faults. To understand these results, the energy differences between the L12 and competing D024 and D019 stacking fault structures and their dependence on composition are computed by density functional theory. This study can help guide researchers to further optimize local phase transformation strengthening mechanisms for alloy development.

Timothy M. Smith↗

NASA NTRSDate not supplied

Solid-state Architecture Batteries for Enhanced Rechargeability and Safety (SABERS) for Electric Aircraft

All-electric vertical take-off and landing vehicles (eVTOL) for urban air mobility (UAM) concepts face numerous challenging technical barriers before their introduction into the consumer marketplace. The primary barrier to overcome is developing an energy storage system capable of meeting the rigorous aerospace safety and performance criteria. The performance metrics for eVTOL vehicles are at least two times greater than those of electric ground vehicles. Furthermore, inherently non-flammable batteries are essential for safe operation of commercial electric aerovehicles. The SABERS concept proposes a battery that meets the key performance criteria through development of a solid-state architecture battery utilizing high-capacity sulfur-selenium cathode and lithium metal anode. The combination of sulfur and selenium offers a balanced energy-to-power density ratio, which can be tailored to the specific application by altering the stoichiometric ratios of sulfur to selenium. This hybrid cathode will be developed by implementing NASA patented holey graphene technology as a highly conductive, ultra-lightweight electrode scaffold. A solid-state electrolyte will be used as a safe, non-flammable replacement to the highly flammable liquid organic electrolytes currently used in SOA lithium-ion batteries. This solid-state lithium-sulfur/selenium cell will be designed into a serial stacking configuration to enable dense packaging of the battery cells. The serial stacking configuration is termed a bipolar stack, which has the advantages of reducing overall cell weight, simplifying the interfaced connections for the cell, and minimizing the cooling requirements. Lastly, optimization of battery components will occur through a robust and rigorous combination of various computational modeling techniques covering multiple length scales. The expected result will be a fully solid-state battery with operational temperatures up to 150 °C which provides the required energy density, discharge rates, and inherent safety to meet the strict aerospace mission performance criteria. This presentation will demonstrate a feasible path for solid-state cells that possess a specific energy of greater than 400 Wh/kg to enable electric aircraft.

Urban Air Mobility (UAM) Vehicles↗

NASA NTRSDate not supplied

Solid-state Architecture Batteries for Enhanced Rechargeability and Safety (SABERS) Beyond Li-Ion: Technology to Enable Sustainable Electric Aviation

All-electric vertical take-off and landing vehicles (eVTOL) for urban air mobility (UAM) concepts face numerous challenging technical barriers before their introduction into the consumer marketplace. The primary barrier to overcome is developing an energy storage system capable of meeting the rigorous aerospace safety and performance criteria. The performance metrics for eVTOL vehicles are at least two times greater than those of electric ground vehicles. Furthermore, inherently non-flammable batteries are essential for safe operation of commercial electric aerovehicles. The SABERS concept proposes a battery that meets the key performance criteria through development of a solid-state architecture battery utilizing high-capacity sulfur-selenium cathode and lithium metal anode. The combination of sulfur and selenium offers a balanced energy-to-power density ratio, which can be tailored to the specific application by altering the stoichiometric ratios of sulfur to selenium. This hybrid cathode will be developed by implementing NASA patented holey graphene technology as a highly conductive, ultra-lightweight electrode scaffold. A solid-state electrolyte will be used as a safe, non-flammable replacement to the highly flammable liquid organic electrolytes currently used in SOA lithium-ion batteries. This solid-state lithium-sulfur/selenium cell will be designed into a serial stacking configuration to enable dense packaging of the battery cells. The serial stacking configuration is termed a bipolar stack, which has the advantages of reducing overall cell weight, simplifying the interfaced connections for the cell, and minimizing the cooling requirements. Lastly, optimization of battery components will occur through a robust and rigorous combination of various computational modeling techniques covering multiple length scales. The expected result will be a fully solid-state battery with operational temperatures up to 150 °C which provides the required energy density, discharge rates, and inherent safety to meet the strict aerospace mission performance criteria. This presentation will demonstrate a feasible path for solid-state cells that possess a specific energy of greater than 400 Wh/kg to enable electric aircraft.

Urban Air Mobility (UAM) Vehicles↗

NASA NTRS2023

Solid-State Architecture Batteries for Enhanced Rechargeability and Safety (SABERS): Advanced Battery Technology for Sustainable Aviation

All-electric vertical take-off and landing vehicles (eVTOL) for urban air mobility (UAM) concepts face numerous challenging technical barriers before their introduction into the consumer marketplace. The primary barrier to overcome is developing an energy storage system capable of meeting the rigorous aerospace safety and performance criteria. The performance metrics for eVTOL vehicles are at least two times greater than those of electric ground vehicles. Furthermore, inherently non-flammable batteries are essential for safe operation of commercial electric aerovehicles. The SABERS concept proposes a battery that meets the key performance criteria through development of a solid-state architecture battery utilizing high-capacity sulfur-selenium cathode and lithium metal anode. The combination of sulfur and selenium offers a balanced energy-to-power density ratio, which can be tailored to the specific application by altering the stoichiometric ratios of sulfur to selenium. This hybrid cathode will be developed by implementing NASA patented holey graphene technology as a highly conductive, ultra-lightweight electrode scaffold. A solid-state electrolyte will be used as a safe, non-flammable replacement to the highly flammable liquid organic electrolytes currently used in SOA lithium-ion batteries. This solid-state lithium-sulfur/selenium cell will be designed into a serial stacking configuration to enable dense packaging of the battery cells. The serial stacking configuration is termed a bipolar stack, which has the advantages of reducing overall cell weight, simplifying the interfaced connections for the cell, and minimizing the cooling requirements. Lastly, optimization of battery components will occur through a robust and rigorous combination of various computational modeling techniques covering multiple length scales. The expected result will be a fully solid-state battery with operational temperatures up to 150 °C which provides the required energy density, discharge rates, and inherent safety to meet the strict aerospace mission performance criteria. This presentation will demonstrate a feasible path for solid-state cells that possess a specific energy of greater than 400 Wh/kg to enable electric aircraft. The presentation will also explore novel materials and computational models used to achieve all solid-state cells that operate safely at very high temperatures and specific energies. The cells can withstand damage while operating without an increase in temperature or spontaneous ignition.

Urban Air Mobility (UAM) Vehicles↗