Results for “concentration potential” — Page 59

DOE OSTI2020

Leaching of Rare Earth Elements from Central Appalachian Coal Seam Underclays

Rare earth elements (REE) are necessary for advanced technological and energy applications. To support the emerging need, it is necessary to identify new domestic sources of REE and technologies to separate and recover saleable REE product in a safe and economical manner. Underclay rock associated with Central Appalachian coal seams and prevalent in coal utilization waste products is an alternative source of REE to hard rock ores that are mainly composed of highly refractory REE-bearing minerals. This study utilizes a suite of analytical techniques and benchtop leaching tests to characterize the properties and leachability of the coal seam underclays sampled. Laboratory bench-top and flow-through reactor leaching experiments were conducted on underclay rock powders to produce a pregnant leach solution (PLS) that has relatively low concentrations of gangue elements Al, Si, Fe, and Th and is amenable to further processing steps to recover and produce purified REE product. The leaching method described here uses a chelating agent, the citrate anion, to solubilize elements that are adsorbed, or weakly bonded to the surface of clay minerals or other mineral solid phases in the rock. The citrate PLS produced from leaching specific underclay powders contains relatively higher concentrations of REE and lower concentrations of gangue elements compared to PLS produced from sequential digestion using ammonium sulfate and mineral acids. Citrate solution leaching of underclay produces a PLS with lower concentrations of gangue elements and higher concentrations of REE than achieved with hydrochloric acid or sulfuric acid. The results provide a preliminary assessment of the types of REE-bearing minerals and potential leachability of coal seam underclays from the Central Appalachian basin.

58 GEOSCIENCES↗

DOE OSTI2024

Simulating hindered grain boundary diffusion using the smoothed boundary method

Abstract Grain boundaries can greatly affect the transport properties of polycrystalline materials, particularly when the grain size approaches the nanoscale. While grain boundaries often enhance diffusion by providing a fast pathway for chemical transport, some material systems, such as those of solid oxide fuel cells and battery cathode particles, exhibit the opposite behavior, where grain boundaries act to hinder diffusion. To facilitate the study of systems with hindered grain boundary diffusion, we propose a model that utilizes the smoothed boundary method to simulate the dynamic concentration evolution in polycrystalline systems. The model employs domain parameters with diffuse interfaces to describe the grains, thereby enabling solutions with explicit consideration of their complex geometries. The intrinsic error arising from the diffuse interface approach employed in our proposed model is explored by comparing the results against a sharp interface model for a variety of parameter sets. Finally, two case studies are considered to demonstrate potential applications of the model. First, a nanocrystalline yttria-stabilized zirconia solid oxide fuel cell system is investigated, and the effective diffusivities are extracted from the simulation results and are compared to the values obtained through mean-field approximations. Second, the concentration evolution during lithiation of a polycrystalline battery cathode particle is simulated to demonstrate the method’s capability.

Materials Science↗

DOE OSTI2022

Electrochemical Corrosion of SIMFUEL: Effects of dissolved H2 and noble metal particles

This report describes the results from electrochemical corrosion tests that were conducted using simulated spent fuel (SIMFUEL) materials comprised of UO2 and surrogate fission products. Two SIMFUEL compositions were tested to quantify the effect of noble metal inclusions and dissolved H2 on the UO2 dissolution rate. One material consisted of UO2 with added lanthanide oxides (UO2 N) and the other consisted of UO2 with added lanthanide oxides and noble metals (UO2-H) at concentrations to simulate high burnup fuel. The electrochemical corrosion tests on the SIMFUEL materials were conducted in aqueous electrolyte solutions (pH 10) that were either saturated with air or purged with a H2/Ar gas mixture to maintain a constant dissolved H2 concentration. The results from electrochemical corrosion tests on SIMFUEL can be applied to qualitatively understand and also quantify the separate effects of water chemistry and fuel composition on the degradation behavior of the UO2 matrix. Open circuit potential (OCP) measurements on a SIMFUEL material of known composition (i.e., known fraction of NMPs at the fuel surface) immersed in a known solution chemistry (i.e., pH, Eh, [O2], [H2]) at known temperature provide qualitative insight into the degradation behavior of the UO2 matrix. If the OCP is above the threshold potential at which the oxidative dissolution of U(IV) to U(VI) occurs, the SNF is expected to degrade by oxidative processes under the experimental conditions. The net currents that are measured during potentiostatic tests, during which the surface potential of the SIMFUEL material is fixed by a potentiostat, can be used to quantify the UO2 degradation rate and optimize the rate constant values used in the Fuel Matrix Degradation Model (FMDM) for half reactions that occur on the SNF surface. Specifically, electrochemical measurements enable the estimation of the total anodic current at ECORR–which is the surface potential at which the total anodic and total cathodic currents are equal–so that the rate constant values for key reactions can be calculated. The open circuit potential measurements, potentiostatic tests, surface property measurements (scanning electron microscopy images and electrochemical impedence spectroscopy plots), and solution elemental composition analyses are being performed to update and optimize the FMDM. A case study is presented herein to show how electrochemical corrosion test results and accompanying characterization results for the UO2 N material in air-saturated solution can be used to validate the SNF surface reaction module of the FMDM. Future electrochemical tests will be conducted to provide quantitative information on the effects of NM content (burnup), H2 concentration, water chemistry, temperature, and galvanic couples with cladding and EBS alloys on UO2 degradation that can be used to improve the accuracy and functionality of the FMDM.

Thomas, Sara↗

DOE OSTI2022

Laboratory and pilot-scale studies of membrane distillation for desalination of produced water from Permian Basin

Substantial quantities of produced water generated during the extraction of oil and gas from unconventional reservoirs present significant environmental concern and increase the operating cost for this industry. Membrane Distillation (MD) can serve as a potential solution for beneficial reuse of produced water by generating high-quality permeate and reducing the volume of produced water requiring disposal. This study investigated treatment of produced water from Permian Basin in both laboratory and pilot-scale studies. Laboratory tests revealed the potential to successfully recover 50% of produced water although some increase in permeate conductivity was observed due to the passage of ammonia from the feed side. Initial pilot-scale test with filtration of raw produced water as the only pre-treatment step led to precipitation of SrSO 4 , NaCl, and Fe in the system once the solubility limits for these salts were exceeded. However, chemical pretreatment that included pH adjustment, aeration, and barite precipitation, allowed successful steady-state operation of the AGMD pilot system for 5 days where the produced water was concentrated from 127 g/L to 255 g/L (~50% water recovery) while recovering high quality permeate. Overall, greater than 99.7 % salt rejection was achieved with the average permeate flux of 1.86 LMH. Finally, mass balance analysis suggested potential Ba and Ca precipitation in the system but there was no impact on AGMD performance and permeate quality during 5 days of continuous operation in the field.

42 ENGINEERING↗

DOE OSTI2019

High-affinity Cu(I) chelator PSP-2 as potential anti-angiogenic agent

Copper is an essential trace metal that has been implicated in angiogenesis, the formation of new blood vessels. As tumor growth relies on establishing a functional capillary network for blood supply, copper chelation therapy may hold promise as an anti-cancer strategy by suppressing angiogenesis. To test the anti-angiogenic effect of PSP-2, a recently developed high affinity Cu(I) chelator with low zeptomolar dissociation constant, we utilized the endothelial cancer cell line EAhy926 and assessed changes in cell migration, proliferation, and tube formation in Matrigel. In addition, sprouting was assessed by the chicken and sheep aortic ring assay, and vascular pattern formation was studied in the chorioallantoic membrane of chicken embryos (CAM assay). While incubation with PSP-2 resulted in selective depletion of cellular copper levels, cell migration was not affected and the proliferating activity was even slightly increased. Moreover, the endothelial tube formation assay revealed significant morphological changes in the presence of PSP-2, with thicker tubular walls and an overall decreased meshes area. Similarly, the aortic ring assay and CAM assay showed that PSP-2 evokes significantly longer sprouts with smaller angles at branching points. Altogether, PSP-2 exhibits significant bioactivity at concentrations as low as 5 μM, rendering it a promising anti-angiogenic agent. As EAhy926 cells exhibit both endothelial and tumorigenic properties, the anti-angiogenic effect of PSP-2 might potentially translate also into anticancer activity.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2020

Database of pharmacokinetic time-series data and parameters for 144 environmental chemicals

Time courses of compound concentrations in plasma are used in chemical safety analysis to evaluate the relationship between external administered doses and internal tissue exposures. This type of experimental data is rarely available for the thousands of non-pharmaceutical chemicals to which people may potentially be unknowingly exposed but is necessary to properly assess the risk of such exposures. In vitro assays and in silico models are often used to craft an understanding of a chemical’s pharmacokinetics; however, the certainty of the quantitative application of these estimates for chemical safety evaluations cannot be determined without in vivo data for external validation. To address this need, we present a public database of chemical time-series concentration data from 567 studies in humans or test animals for 144 environmentally-relevant chemicals and their metabolites (187 analytes total). All major administration routes are incorporated, with concentrations measured in blood/plasma, tissues, and excreta. We also include calculated pharmacokinetic parameters for some studies, and a bibliography of additional source documents to support future extraction of time-series. In addition to pharmacokinetic model calibration and validation, these data may be used for analyses of diferential chemical distribution across chemicals, species, doses, or routes, and for meta-analyses on pharmacokinetic studies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Rare earth element potential in coal and coal ash in the U.S. Gulf Coast

United States heavy reliance on imports of critical minerals (CMs), including rare earth elements (REEs), underscores the importance of development of domestic sources. The study objective was to quantify CM and REE concentrations in coal and coal ash in the US Gulf Coast region. CM and REE concentrations were measured for 118 samples from outcrops and 14 mines in the Gulf Coast. Results show that total REE + Yttrium (REY) concentrations (dry coal basis) are comparable to those of the upper continental crust (UCC) with localized hot spots, such as the Texas Gibbons Creek mine (REY ≤ ~ 2860 ppm). When normalized to UCC REY concentration (169 ppm, dry coal basis), REY to UCC ratios for Gulf Coast coal samples range from 0.1 to 17 (median ratio 0.6). REE extractability from lignites is high (median: 63%–93%) using environmentally benign weak acid. In addition to raw coal, coal ash from power plants could also serve as an REE source with a median ratio of REY in ash relative to coal of 4; however, extractability from coal ash is generally much lower (≤ 5% using the same weak acid as in coal). The median basket price for extracted REY as oxides from coal, assuming 70% extractability, is $\$3.2$ per tonne of coal and $\$186$ billion based on 58 billion metric tonnes of dry coal in the Gulf Coast. REEs important for magnets (Pr + Nd + Tb + Dy) account for ~ 80% of the total value. The corresponding median basket price for extracted REY as oxides from coal ash, assuming ~ 30% extractability, is ~$\$4.4$ per tonne of ash and $\$1.2$ billion based on 258 million tonnes of ash. REE production from coal would likely require co-products, such as activated carbon or humic acids, to attain economic viability. Production of REEs from coal ash could offset remediation costs related to potential water contamination. This reconnaissance study shows the potential for REE production from coal and coal ash in the Gulf Coast; however, carbon coproducts and/or societal benefits would likely be required for socioeconomic viability.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2023

The exceptional form and function of the giant bacterium Ca. Epulopiscium viviparus revolves around its sodium motive force

Epulopiscium spp. are the largest known heterotrophic bacteria; a large cigar-shaped individual is a million times the volume of Escherichia coli. To better understand the metabolic potential and relationship of Epulopiscium sp. type B with its host Naso tonganus, we generated a high-quality draft genome from a population of cells taken from a single fish. We propose the name Candidatus Epulopiscium viviparus to describe populations of this best-characterized Epulopiscium species. Metabolic reconstruction reveals more than 5% of the genome codes for carbohydrate active enzymes, which likely degrade recalcitrant host-diet algal polysaccharides into substrates that may be fermented to acetate, the most abundant short-chain fatty acid in the intestinal tract. Moreover, transcriptome analyses and the concentration of sodium ions in the host intestinal tract suggest that the use of a sodium motive force (SMF) to drive ATP synthesis and flagellar rotation is integral to symbiont metabolism and cellular biology. In natural populations, genes encoding both F-type and V-type ATPases and SMF generation via oxaloacetate decarboxylation are among the most highly expressed, suggesting that ATPases synthesize ATP and balance ion concentrations across the cell membrane. High expression of these and other integral membrane proteins may allow for the growth of its extensive intracellular membrane system. Further, complementary metabolism between microbe and host is implied with the potential provision of nitrogen and B vitamins to reinforce this nutritional symbiosis. The few features shared by all bacterial behemoths include extreme polyploidy, polyphosphate synthesis, and thus far, they have all resisted cultivation in the lab.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2025

Data for Identifying the best high-biomass sorghum hybrids based on biomass yield potential and feedstock quality affected by nitrogen fertility management under various environments

Data were collected from agronomy fields in Urbana and Ewing, IL, during the 2022 and 2023 growing seasons. The dataset includes dry biomass yield, nitrogen, phosphorus, and potassium concentrations and removals, and chemical composition elements (cellulose, hemicellulose, lignin, and soluble fractions) for 13 high-biomass sorghum hybrids. data_sharing.xlsx contains 20 columns and 104 rows. Below is the explanation of all variables in the file: Year: 2022; 2023 Location: Urbana, IL; Ewing, IL N rate (kg-N/ha): 0; 112 Hybrid #: H1-H13 Pedigree: Pedigree for 13 hybrids Dry biomass yield (Mg/ha): Aboveground dry biomass yield N (g/kg): Nitrogen concentration in plant tissue P (g/kg): Phosphorus concentration in plant tissue K (g/kg): Potassium concentration in plant tissue N (kg/ha): Nitrogen removal by aboveground biomass P (kg/ha): Phosphorus removal by aboveground biomass K (kg/ha): Potassium removal by aboveground biomass Cellulose (g/kg): Cellulose concentration in plant tissue Hemicellulose (g/kg): Hemicellulose concentration in plant tissue Lignin (g/kg): Lignin concentration in plant tissue Soluble (g/kg): Soluble concentration in plant tissue Cellulose (Mg/ha): Cellulose content in aboveground biomass Hemicellulose (Mg/ha): Hemicellulose content in aboveground biomass Lignin (Mg/ha): Lignin content in aboveground biomass Soluble (Mg/ha): Soluble content in aboveground biomass

environmental adaptability↗

DOE OSTI2024

In Vitro Antimicrobial Activity of Volatile Compounds from the Lichen Pseudevernia furfuracea (L.) Zopf. Against Multidrug-Resistant Bacteria and Fish Pathogens

Lichens are symbiotic organisms with unique secondary metabolism. Various metabolites from lichens have shown antimicrobial activity. Nevertheless, very few studies have investigated the antimicrobial potential of the volatile compounds they produce. This study investigates the chemical composition and antimicrobial properties of volatile compounds from Pseudevernia furfuracea collected in two regions of Morocco. Hydrodistillation was used to obtain volatile compounds from samples collected in the High Atlas and Middle Atlas. Gas chromatography–mass spectrometry (GC-MS) analysis identified phenolic cyclic compounds as the primary constituents, with atraric acid and chloroatranol being the most abundant. Additionally, eight compounds were detected in lichens for the first time. The antimicrobial activity of these compounds was assessed using disc diffusion and broth microdilution methods. Both samples demonstrated significant antimicrobial effects against multidrug-resistant human bacteria, reference microorganisms, fish pathogens, and Candida albicans, with minimum inhibitory concentrations (MICs) ranging from 1000 µg/mL to 31.25 µg/mL. This study provides the first report on the volatile compounds from Pseudevernia furfuracea and their antimicrobial effects, particularly against fish pathogens, suggesting their potential as novel antimicrobial agents for human and veterinary use. Further research is warranted to explore these findings in more detail.

Essadki, Yasser (ORCID:0009000648460075)↗

DOE OSTI2026

Evaluation of coal-associated sediments, wastes, and AMD sludge in the Southern Appalachian Basin as feedstock materials for REE and Li recovery

Critical minerals (CM) such as rare earth elements (REE+) and Lithium (Li) are essential to technological innovation, energy transitions, global economic and defense security, necessitating the search for unconventional resources and efficient recovery methods to avert supply chain disruptions. Here, this study evaluates coal-associated sediments (underclay and roof rock) and wastes from the Pennsylvanian Pottsville Formation of the Southern Appalachian Basin (SAB) as potential feedstocks for CM recovery. A total of 34 samples (15 underclays, 12 roof rocks, 5 Acid Mine Drainage (AMD) sludges, and 2 coal mining wastes) were characterized using XRD, XRF, ICP-MS, and μ-XRF analytical methods. The REE+ and Li concentrations of these materials ranged from 46.8 to 334.4 ppm and from 11.1 to 519 ppm, respectively, with one underclay sample (Hendrix 3456) yielding the highest values for both. Bulk mineralogy for all samples was dominated by aluminosilicate clay phases, particularly illite and kaolinite. All samples exhibited REY def, rel% values >26% and C outl indices that ranged from 0.69 to 0.94, classifying their REE ore potential as Category II (Promising) as defined by Seredin and Dai (2012). Extractability tests (EPA method 3051 A) yielded low REE+ and Li recoveries, with maximum values of 3.3% and 3.6%, respectively, suggesting associations with resistant minerals like clay and phosphates. Elemental mapping indicates that REE+ is associated with phosphate, whereas statistical analysis suggests that REE+ are associated with aluminosilicates, suggesting heterogeneous associations or minimal phosphate contribution. Li also correlated positively with Al 2 O 3 , indicating an aluminosilicate host. This study highlights the potential of coal-associated sediments in the SAB.

Clay minerals↗

DOE OSTI2021

Effect of electrode rinse solutions on the electrodialysis of concentrated salts

The data presented indicate that modest attention to the chemistry of the electrode rinse solution can yield as much as 56% improvement in process efficiency. When operating electrodialysis (ED) with salt concentrations greater than 10,000 mg/l (as NaCl) the amperage can be relatively high even at low voltages. To maximize the overall rate of ion transport from diluate to concentrate, there is a need to minimize resistances in the electrode cells since these can represent as much as 30% of the total resistances in the entire process and in this particular ED unit, represented resistance roughly equivalent to that within the membrane stack. This work describes the performance of a 10-cell pair, 200 cm 2 (0.02 m 2 ) per membrane, pilot ED unit operated in batch mode at 5 V potential. The feedstock to the stack was varied from 0.5% to 6% NaCl. Results from Volt-amp profiles (2.0–15 V) were used as the rationale for choosing the preferred electrode rinse solution, 90 g/l (kg/m 3 ) disodium sulfate at pH 12.5. The recommended solution of 30 g/l (kg/m 3 ) disodium sulfate at neutral pH was tested against stronger solutions (60, 90, and 120 g/l (kg/m 3 ) disodium sulfate) at neutral pH and with 1 g/l (kg/m 3 ) sodium hydroxide added to yield solutions at pH 12.5. There were stark differences in the performance of the ED unit between the solutions at pH 7 and those at pH 12.5. The slopes of the Volt-amp profiles improved indicating less resistance to ion flow at pH 12.5. Most of the difference can be attributed to the greater conductivity of sodium hydroxide compared to disodium sulfate, where even a modest addition of 1 g/l (kg/m 3 ) sodium hydroxide increased the conductivity of the solution between 8 and 20% depending on the concentration of disodium sulfate. Most notably, the initiation voltage was 2.39 ± 0.08 V with solutions at pH 7 and 1.99 V ± 0.04 V when the rinse solutions were around pH 12.5, a difference of around 0.42 V. Since the full batch runs were performed at 5.0 V, this 0.42 V differential represented a loss of 8% in process efficiency. A series of tests showed a shift in initiation voltage occurred between pH 11.5 and 12.5. Nernst equations for water electrolysis are coupled with a simple flux model that estimates the concentration of hydroxide and hydronium ions at the electrode surfaces. This model indicates that the potential demanded by the electrodes is directly linked to the current. Furthermore, there is a steep drop in the potential demanded by the anode when there is sufficient hydroxide available to generate oxygen from hydroxide as opposed to generation from water. The voltage demand is minimal at pH 12.5 and reflective of the reference standard voltage (just over 1.23 V predicted at 0.1 amps). However, the flux model predicts that the voltage demanded by the electrodes at pH 7 is 1.61 V at 0.1 amps (the lowest amperage measurable with the power pack). In conclusion, comparing this result to the reference standard (E 0 = -1.23 V) yields a satisfactory explanation for the observed difference below reference standard of 0.42 V.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Decarbonization of Wastewater Treatment with Microalgae Processes.

Microalgae can contribute to the decarbonization of wastewater treatment by municipalities, industries and agriculture, by substituting sunlight for energy intensive conventional treatment processes, while capturing nutrients and carbon in the algal biomass. The carbon fixed into the algal biomass can be converted to renewable natural gas (RNG) using anaerobic digestion or into renewable diesel and sustainable aviation fuel (SAF) using hydrothermal liquefaction (HTL), with greatly reduce the carbon footprints compared to conventional fuels. Bioplastics, biofertilizers and other bioproducts from microalgae biomass also provide potential benefits in greenhouse gas (GHG) reduction and domestic supply chains. Microalgae technologies can counter eutrophication caused by harmful algal blooms by recovering nutrients, N and P, from wastewaters, and even from very low nutrient concentrations found in surface waters. CO2 is required in microalgae cultivation and wastewater treatment to support maximal rates of the photosynthesis, with the CO2 obtained from the wastes themselves, other local sources or even atmospheric CO2. Greenhouse gas mitigation with microalgae processes is based on life cycle assessments, comparing such green processes with current energy intensive wastewater treatment, and nutrient reduction technologies. Microalgae technologies are specifically relevant to smaller, often disadvantaged, communities, where currently about 5,000 algae wastewater treatment ponds are operated by public utilities with many more are operated by industries. However, many, if not most, of these pond facilities require urgent technology upgrades to achieve the potential and goals of low cost GHG mitigation and efficient nutrient recycling. MicroBio Engineering Inc. is developing and has demonstrated several technologies that combine innovative carbon mitigation and decarbonization technologies for a circular economy, with longer-term potential for large-scale biofuels and biofertilizer production.

09 BIOMASS FUELS↗

DOE OSTI2023

Decarbonization of Wastewater Treatment with Microalgae Processes.

Microalgae can contribute to the decarbonization of wastewater treatment by municipalities, industries and agriculture, by substituting sunlight for energy intensive conventional treatment processes, while capturing nutrients and carbon in the algal biomass. The carbon fixed into the algal biomass can be converted to renewable natural gas (RNG) using anaerobic digestion or into renewable diesel and sustainable aviation fuel (SAF) using hydrothermal liquefaction (HTL), with greatly reduce the carbon footprints compared to conventional fuels. Bioplastics, biofertilizers and other bioproducts from microalgae biomass also provide potential benefits in greenhouse gas (GHG) reduction and domestic supply chains. Microalgae technologies can counter eutrophication caused by harmful algal blooms by recovering nutrients, N and P, from wastewaters, and even from very low nutrient concentrations found in surface waters. CO2 is required in microalgae cultivation and wastewater treatment to support maximal rates of the photosynthesis, with the CO2 obtained from the wastes themselves, other local sources or even atmospheric CO2. Greenhouse gas mitigation with microalgae processes is based on life cycle assessments, comparing such green processes with current energy intensive wastewater treatment, and nutrient reduction technologies. Microalgae technologies are specifically relevant to smaller, often disadvantaged, communities, where currently about 5,000 algae wastewater treatment ponds are operated by public utilities with many more are operated by industries. However, many, if not most, of these pond facilities require urgent technology upgrades to achieve the potential and goals of low cost GHG mitigation and efficient nutrient recycling. MicroBio Engineering Inc. is developing and has demonstrated several technologies that combine innovative carbon mitigation and decarbonization technologies for a circular economy, with longer-term potential for large-scale biofuels and biofertilizer production.

09 BIOMASS FUELS↗

DOE OSTI2023

Decarbonization of Wastewater Treatment with Microalgae Processes.

Microalgae can contribute to the decarbonization of wastewater treatment by municipalities, industries and agriculture, by substituting sunlight for energy intensive conventional treatment processes, while capturing nutrients and carbon in the algal biomass. The carbon fixed into the algal biomass can be converted to renewable natural gas (RNG) using anaerobic digestion or into renewable diesel and sustainable aviation fuel (SAF) using hydrothermal liquefaction (HTL), with greatly reduce the carbon footprints compared to conventional fuels. Bioplastics, biofertilizers and other bioproducts from microalgae biomass also provide potential benefits in greenhouse gas (GHG) reduction and domestic supply chains. Microalgae technologies can counter eutrophication caused by harmful algal blooms by recovering nutrients, N and P, from wastewaters, and even from very low nutrient concentrations found in surface waters. CO2 is required in microalgae cultivation and wastewater treatment to support maximal rates of the photosynthesis, with the CO2 obtained from the wastes themselves, other local sources or even atmospheric CO2. Greenhouse gas mitigation with microalgae processes is based on life cycle assessments, comparing such green processes with current energy intensive wastewater treatment, and nutrient reduction technologies. Microalgae technologies are specifically relevant to smaller, often disadvantaged, communities, where currently about 5,000 algae wastewater treatment ponds are operated by public utilities with many more are operated by industries. However, many, if not most, of these pond facilities require urgent technology upgrades to achieve the potential and goals of low cost GHG mitigation and efficient nutrient recycling. MicroBio Engineering Inc. is developing and has demonstrated several technologies that combine innovative carbon mitigation and decarbonization technologies for a circular economy, with longer-term potential for large-scale biofuels and biofertilizer production.

09 BIOMASS FUELS↗

DOE OSTI2025

The Impact of Europium as a Fission Product Surrogate on Chromium Corrosion in Molten Chloride Salt

The rising interest in molten salts, both as thermal energy storage media and as high-temperature solvents for fissile materials in advanced nuclear reactors, has spurred significant growth in research on structural and functional salt-facing materials. Impurities, such as water, play a significant role in the degradation of materials in molten salt environments. Other impurities, such as fission products, are expected to accumulate in molten salts during normal reactor operation and can affect the properties of the salt and salt-facing materials. During normal reactor operation, rare-earth element species are expected to form as byproducts of fission reactions, potentially degrading or altering the performance of both structural and functional materials exposed to salts. Here, in this work, fission product surrogates, europium metal and EuCl 3 , were added to the KCl-MgCl 2 salt while exposing pure Cr specimens in the melt at 600 and 700 °C for 1000 h. Low reactivity was observed with the baseline salt, while both the Eu and EuCl 3 additions to the salt resulted in increased mass loss of Cr specimens. A capillary electrophoresis technique was developed to enable the detection of low parts-per-million (ppm) concentrations of europium (Eu) in chloride salt both before and after exposure of Cr metal. This technique provides a sensitive and reliable method for monitoring trace levels of Eu, which is critical for understanding the interactions and potential contamination effects in salt-facing materials during reactor operation. This quantification technique can be applied to other cationic and anionic contaminants in halide salts.

chloride salt↗

DOE OSTI2022

Anion Effects on the Interfacial Structure and Bulk Physical Properties in Choline-Based Hydrogen-Bonded Electrolytes

Electrolytes consisting of choline (Ch) salts with acetate (Ac) and oxalate (Ox) anions were studied in mixtures with ethylene glycol (EG), in comparison to chloride (Cl)- and bis(trifluorosulfonyl)imide (TFSI)-containing systems to understand the impact of anion size and charge density on the bulk electrolyte and interfacial properties. These represent hydrogen-bonded concentrated electrolytes where the Ch salts are the H-bond acceptors (HBAs) and EG is the H-bond donor (HBD) in 1:2 and 1:4 HBA:HBD ratios. Increased H-bonding in Ch 2 Ox with EG compacts the liquid compared to ChAc, consistent with the increased dissociation energies of the HBA:HBD clusters with Ox –2 calculated by density functional theory (DFT), thus leading to denser and more viscous liquids. Electrochemical impedance spectroscopy (EIS) and surface-enhanced Raman spectroscopy (SERS) were used to investigate interfacial charge density and the electrode surface species. Differential capacitance curves demonstrate weak dependence on potential except for ChAc:EG, where Ac – is found to adsorb on the Au surface, in particular at +0.055 V vs Ag quasi-reference while no specific adsorption was observed on glassy carbon (GC). In situ SERS measurement confirms the formation of a surface layer in the ChAc:EG systems resulting from a Au–acetate interaction. Despite the structural similarities, Ox –2 did not show specific binding or any dependence of capacitance on potential as a result of strongly solvating EG molecules via H-bonds. Furthermore, this study shows that the charge density of the HBAs impacts both bulk properties and the electrical double-layer formation in concentrated H-bonded electrolytes that is relevant to electrochemical kinetics and morphology in electrodeposition processes and energy storage applications.

25 ENERGY STORAGE↗

DOE OSTI2021

Process Engineering to Increase the Layered Phase Concentration in the Immediate Products of Flame Spray Pyrolysis

Flame-spray-pyrolysis (FSP) is a robust and scalable process to synthesize particles at the commodity-scale. FSP has been used to produce the precursor powders which were converted to the layered structure $(R\bar{3m} \text { phase})$ by a postannealing step in making nickel-rich cathode materials (NCMs). Theoretically, the high flame temperature (normally >1500 K) in FSP can provide adequate energy for the phase conversion from rock-salt to layered structures and potentially enables one-step synthesis. However, the high flame temperature is a critical issue to cause lithium loss and structural degradation, preventing the formation of the layered phase. Here, guided by the gaseous nucleation theory, we implemented several FSP processes with different solution recipes. The layered phase concentration in the as-burned products can be increased with the solution enthalpies. By adding a rapid quench step to suppress the lithium loss and phase degradation, the layered phase can be further increased. This work contributes new ideas to innovating process regarding the process efficiency and throughput of manufacturing cathode materials at a large scale.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗