Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “beta”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Evidence for detection of a moving magnetic monopole

A very heavy particle passed through a balloon-borne stack of Cherenkov film, emulsion, and Lexan sheets. In 33 Lexan sheets it produced tracks expected of either a nucleus with Z ranging between 125 and 137 and with beta less than about 0.92 or a magnetic monopole with g = 137e. Its track structure in emulsion indicated it was moving downward with beta equal to 0.5 (plus 0.1 or minus 0.05) and was either a nucleus with Z equal to 80 or a monopole with g = 137e. These facts strongly favor identification of the particle as a magnetic monopole of strength g = 137e and mass greater than 200 times proton mass.

Price, P. B.↗

Cardiorespiratory responses to orthostasis and the effects of propranolol

Cardiac output and gas exchange were determined serially using the single-breath method of Kim et al. before, during, and after orthostasis on six subjects after beta-adrenergic blockage and in duplicate controls. In the latter, heart rate increased and pulse pressure dropped immediately on tilting to 60 deg and remained stable while cardiac output and stroke volume declined gradually over 21 min upright. On propranolol, heart rate was 10 bpm lower supine and 20 bpm less at 60 deg but cardiac output was only slightly lower before and following tilt-up. However, after 15 min upright, stroke volume and cardiac output recovered on propranolol exceeding the controls after 21 min without change in heart rate. Returning to supine, heart rate dropped in all tests with a transitory increase in stroke volume, cardiac output and arteriovenous O2 difference. At the same time, apparent O2 uptake increased temporarily, reflecting the return of pooled venous blood to the lungs. Orthostatic tolerance did not appear to be affected by beta-adrenergic blockade.

Loeppky, J. A.↗

Near threshold response of a wave shifted Cerenkov radiator to heavy ions

The response of Pilot 425 to heavy ions with energies less than 600 MeV/amu beta approximately 0.8 is examined both theoretically and experimentally. Measurements are presented from an experiment which employed a Ne-20 beam at many energies below 575 MeV/amu. The signal is assumed to come from three sources: (1) Cerenkov light from the heavy ion, (2) Cerenkov light from secondary electrons, and (3) scintillation of the radiator. It is found that the effective index of refraction is 1.518 and that scintillation is present at a level of approximately 2.7 percent of the Cerenkov signal for beta = 1 for Ne-20. The first of these values differs from values previously quoted in the literature.

Ahlen, S. P.↗

Use of active control technology to improve ride qualities of large transport aircraft

Analyses, construction and flight testing of two systems: Beta-vane and Modal Suppression Augmentation System (MSAS), which were developed to suppress gust induced lateral accelerations of large aircraft, are described. The 747 transport was used as the test vehicle. The purpose of the Beta-vane system is to reduce acceleration levels at the dutch roll frequency whereas the function of the MSAS system is to reduce accelerations due to flexible body motions caused by turbulence. Data from flight test, with both systems engaged shows a 50 to 70 percent reduction in lateral aft body acceleration levels. Furthermore, it is suggested that present day techniques used for developing dynamic equations of motion in the flexible mode region are limited.

Cohen, G. C.↗

A search for molecular hydrogen fluorescence near 100 km

The fluorescence of H2 in the Lyman band system, excited by solar extreme ultraviolet radiation, provides a means for the optical detection of H2 in the upper atmosphere. In particular, the Ly beta line of hydrogen is nearly degenerate with the (6,0) P1 transition, and absorption in this line produces fluorescence in the v-prime = 6 progression, principally at 1265, 1366, 1462 and 1608 A. Absorption by O2 rapidly attenuates the Ly beta from an overhead sun below 100 km and also significantly attenuates the fluorescent radiation. Far-ultraviolet dayglow spectra from 1130 to 1510 A obtained from an Aerobee rocket experiment on 11 December 1972 give an upper limit for any H2 emission which is a factor of 5 higher than expected according to recent hydrogen models.

Feldman, P. D.↗

Verification of the principle of equivalence for massive bodies

Analysis of 1389 measurements, accumulated between 1970 and 1974, of echo delays of laser signals transmitted from earth and reflected from cube corners on the moon shows gravitational binding energy to contribute equally to earth's inertial and passive gravitational masses to within the estimated uncertainty of 1.5%. The corresponding restriction on the Eddington-Robertson parameters is 4(beta) - gamma 3 = -0.001 plus or minus 0.015. Combination with other results, as if independent, yields values for beta and gamma in accord with general relativity.

Shapiro, I. I.↗

Stellar occultation spikes as probes of atmospheric structure and composition

The characteristics of spikes observed in occultation light curves of Beta Scorpii by Jupiter are discussed in terms of the gravity-gradient model. The occultation of Beta Sco by Jupiter on May 13, 1971, is reviewed, and the gravity-gradient model is defined as an isothermal atmosphere of constant composition in which the refractivity is a function only of the radial coordinate from the center of refraction, which is assumed to lie parallel to the local gravity gradient. The derivation of the occultation light curve in terms of the atmosphere, the angular diameter of the occulted star, and the occultation geometry is outlined. It is shown that analysis of the light-curve spikes can yield the He/H2 concentration ratio in a well-mixed atmosphere, information on fine-scale atmospheric structure, high-resolution images of the occulted star, and information on ray crossing. Observational limits are placed on the magnitude of horizontal refractivity gradients, and it is concluded that the spikes are the result of local atmospheric density variations: atmospheric layers, density waves, or turbulence.

Elliot, J. L.↗

New solid conductors of Na/+/ and K/+/ ions

About 40 structure types for solid conductors of Na(+) and K(+) ions are surveyed. Five compounds in three structure types are discovered to be good solid conductors of alkali metal ions, capable of ion transport with conductivities in the vicinity of 0.00001/ohm-cm at 25 C. These compounds are a bcc form of NaSbO3, an orthorhombic layer structure of the composition 2M2O.3Nb2O5 with M equal to Na or K, and the Na pyrochlores NaTa2O5F and NaTaWO6. Ion exchange is required to produce each of these Na compounds. Only the 2K2O.3Nb2O5 can so far be synthesized directly from the oxides and thus is the only one which can be sintered readily. The niobate is about as good a conductor of K(+) ion as is K-beta alumina. The NaSbO3 compares well with Na beta at 280 C. A number of phase diagrams are developed.

Singer, J.↗

The Skylab barium plasma injection experiments. I - Convection observations

Two barium-plasma injection experiments were carried out during magnetically active periods in conjunction with the Skylab 3 mission. The high-explosive shaped charges were launched near dawn on November 27 and December 4, 1973, UT. In both cases, the AE index was near 400 gammas, and extensive pulsating auroras covered the sky. The first experiment, Skylab Alpha, occurred in the waning phase of a 1000-gamma substorm, and the second, Skylab Beta, occurred in the expansive phase of an 800-gamma substorm. In both, the convection was generally magnetically eastward, with 100-km-level electric fields near 40 mV/m. However, in the Alpha experiment the observed orientation of the barium flux tube fit theoretical field lines having no parallel current, but the Beta flux-tube orientation indicated a substantial upward parallel sheet current.

Wescott, E. M.↗

A low speed wind tunnel test of a 0.050 scale model of shuttle orbiter (model 089B) to investigate the longitudinal and lateral directional effects of canard and tail configurational modifications in the LTV LSWT (MA14)

A low speed wind tunnel test was conducted to determine the effects of 6 canard configurations on the 0.050 scale model of shuttle orbiter 089B. In addition, two horizontal tail configurations were tested at two positions on the model as were two wing configurations. Since this test was restricted to 103 runs, only a limited number of permutations of the configurational changes could be tested. The testing was done in the 15 by 20 foot section of the LSWT and consisted of pitch polars, one yawed polar and several yaw runs. The pitch polars encompassed an alpha range from 0 to 28 deg; the yawed polar was run at beta = +2 degrees and the yaw runs covered a beta range from -6 to +6 deg at angles-of-attack of 0, 4, 10, 16, and 20 deg.

Chambliss, E. B.↗

Reaction diffusion in the nickel-chromium-aluminum and cobalt-chromium-aluminum systems

The effects of MCrAl coating-substrate interdiffusion on oxidation life and the general mutliphase, multicomponent diffusion problem were examined. Semi-infinite diffusion couples that had sources representing coatings and sinks representing gas turbine alloys were annealed at 1,000, 1,095, 1,150, or 1,205 C for as long as 500 hours. The source and sink aluminum and chromium contents and the base metal (cobalt or nickel) determined the parabolic diffusion rate constants of the couples and predicted finite coating lives. The beta source strength concept provided a method (1) for correlating beta recession rate constants with composition; (2) for determining reliable average total, diffusion, and constitutional activation energies; and (3) for calculating interdiffusion coefficients.

Levine, S. R.↗

An X-ray fluorescence spectrometer and its applications in materials studies

An X-ray fluorescence system based on a Co(57) gamma-ray source has been developed. The system was used to calculate the atomic percentages of iron implanted in titanium targets. Measured intensities of Fe (k-alpha + k-beta) and Ti (k-alpha + k-beta) X-rays from the Fe-Ti targets are in good agreement with the calculated values based on photoelectric cross sections of Ti and Fe for the Co(57) gamma rays.

Singh, J. J.↗

The C-12/C-13 ratio in stellar atmospheres. VI - Five luminous cool stars

A simple curve-of-growth technique is described for extracting the C-12/C-13 ratio for M stars from high-resolution spectra of CO infrared vibration-rotation lines. The technique is applied to the CO lines at 1.6 and 2.3 microns in spectra of two M supergiants (Alpha Ori and Alpha Sco), two M giants (Alpha Her and Beta Peg), and a Mira-type variable (Chi Cyg). As a check on the CO analysis, the C-12/C-13 ratio is derived from the red CN system at 8000 A for Alpha Sco, Alpha Ori, and Beta Peg. The CO analysis is also applied to the K giant Alpha Boo as a check. The CN and CO results are found to be in general agreement, and the C-12/C-13 ratio in all the examined stars is shown to be considerably lower than the solar-system value. It is suggested that these stars were formed from clouds with a C-12/C-13 ratio of 40 to 89 and that their atmospheres now exhibit an enhancement of C-13 abundance due to internal production and mixing to the surface.

Hinkle, K. H.↗

Measurement of 0.511-MeV gamma rays with a balloon-borne Ge/Li/ spectrometer

A collimated high-resolution gamma ray spectrometer was flown on a balloon over Palestine, Texas, on June 10, 1974, to obtain measurements of the terrestrial and extraterrestrial 0.511-MeV gamma rays. The spectrometer consists of four 40-cu-cm Ge(Li) crystals operating in the energy range 0.06-10 MeV; this cluster of detectors is surrounded by a CsI(Na) anticoincidence shield. This system is used primarily to allow measurements of the two escape peaks associated with high-energy gamma ray lines. It also allows a measurement of the background component of the 0.511-MeV flux produced by beta(+) decays in materials inside the CsI(Na) shield. It is shown that the measurements of the atmospheric fluxes are consistent with earlier results after allowance is made for an additional component of the background due to beta(+) decays produced by neutron- and proton-initiated interactions with materials in and near the detector. Results of the extraterrestrial flux require an extensive detailed analysis of the time-varying background because of activation buildup and balloon spatial drifts.

Ling, J. C.↗

Observed departures from LTE ionization equilibrium in late-type giants

Photoelectric scans of the Ca I line at 6572 A and the forbidden Ca II transition at 7323 A are studied in the K giant alpha Tau, the M supergiant alpha Ori, and the M giants beta And, alpha Cet, mu Gem, and beta Peg. The relative strengths of these lines are shown to be indicative of the ratio of the relative number densities of the neutral and ionized species in the photosphere. The analysis indicates an overionization relative to LTE in qualitative agreement with the theoretical calculations of Auman and Woodrow for the K and M giants. The M supergiant alpha Ori exhibits a large overionization relative to LTE.

Ramsey, L. W.↗

Consolidation of silicon nitride without additives

The feasibility of producing a sound, dense Si3N4 body without additives was explored, using conventional gas hot isostatic pressing techniques and an uncommon hydraulic hot isostatic pressing technique. These two techniques produce much higher pressure 275-413 MN/m sq (40,000 - 60,000 psi) than hot-pressing techniques. Evaluation was based on density measurement, microscopic examination, both optical and electron, and X-ray diffraction analysis. The results are summarized as follows: (1) Si3N4 can be densified to high density, greater than 95% of theoretical, without additions. (2) The higher density Si3N4 specimens appear to be associated with a greater amount of alpha to beta transformation. (3) Under high pressure, the alpha to beta transformation can occur at a temperature as low as 1150 C. (4) Grain deformation and subsequent recrystallization and grain refinement result from hot isostatic pressing of Si3N4.

Sikora, P. F.↗

Benefit evaluation of space processing of biological materials

A rational analytical basis for the evaluation of potential benefits of space processing of biological materials is described. A preliminary evaluation of three candidate space processed biological materials was accomplished. Materials investigated were human lymphocytes, urokinase, and Beta cells. Separation of lymphocyte groups was considered in order to improve the matching of donors and recipients for kidney transplantation, while urokinase was examined in regard to treatment of thromboembolic diseases. Separation of Beta cells was studied since it could provide a highly effective means for the treatment of juvenile-onset diabetes.

Source record↗

Elevated-temperature flow strength, creep resistance and diffusion welding characteristics of Ti-gAl-2Nb-1Ta-0.8Mo

A study of the flow strength, creep resistance and diffusion welding characteristics of the titanium alloy Ti-6Al-2Nb-1Ta-0.8Mo was conducted. Two mill-processed forms of this alloy were examined. The forged material was essentially processed above the beta transus while the rolled form was subjected to considerable work below the beta transus. Between 1150 and 1250 K, the forged material was stronger and more creep resistant than the rolled alloy. Both forms exhibit superplastic characteristics in this temperature range. Strain measurements during diffusion welding experiments at 1200 K reveal that weld interfaces have no measurable effect on the overall creep deformation. Significant deformation appears to be necessary to produce a quality diffusion weld between superplastic materials. A 'soft' interlayer inserted between faying surfaces would seemingly allow manufacture of quality diffusion welds with little overall deformation.

Whittenberger, J. D.↗