Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attenuator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Effect of stress on ultrasonic pulses in fiber reinforced composites

An acoustical-ultrasonic technique was used to demonstrate relationships existing between changes in attenuation of stress waves and tensile stress on an eight ply 0 degree graphite-epoxy fiber reinforced composite. All tests were conducted in the linear range of the material for which no mechanical or macroscopic damage was evident. Changes in attenuation were measured as a function of tensile stress in the frequency domain and in the time domain. Stress wave propagation in these specimens was dispersive, i.e., the wave speed depends on frequency. Wave speeds varied from 267,400 cm/sec to 680,000 cm/sec as the frequency of the signal was varied from 150 kHz to 1.9 MHz which strongly suggests that flexural/lamb wave modes of propagation exist. The magnitude of the attenuation changes depended strongly on tensile stress. It was further observed that the wave speeds increased slightly for all tested frequencies as the stress was increased.

Hemann, J. H.↗

Ultrasonic determination of recrystallization

Ultrasonic attenuation was measured for cold worked Nickel 200 samples annealed at increasing temperatures. Localized dislocation density variations, crystalline order and colume percent of recrystallized phase were determined over the anneal temperature range using transmission electron microscopy, X-ray diffraction, and metallurgy. The exponent of the frequency dependence of the attenuation was found to be a key variable relating ultrasonic attenuation to the thermal kinetics of the recrystallization process. Identification of this key variable allows for the ultrasonic determination of onset, degree, and completion of recrystallization.

Generazio, E. R.↗

Evaluation of a scale-model experiment to investigate long-range acoustic propagation

Tests were conducted to evaluate the feasibility of using a scale-model experiment situated in an anechoic facility to investigate long-range sound propagation over ground terrain. For a nominal scale factor of 100:1, attenuations along a linear array of six microphones colinear with a continuous-wave type of sound source were measured over a wavelength range from 10 to 160 for a nominal test frequency of 10 kHz. Most tests were made for a hard model surface (plywood), but limited tests were also made for a soft model surface (plywood with felt). For grazing-incidence propagation over the hard surface, measured and predicted attenuation trends were consistent for microphone locations out to between 40 and 80 wavelengths. Beyond 80 wavelengths, significant variability was observed that was caused by disturbances in the propagation medium. Also, there was evidence of extraneous propagation-path contributions to data irregularities at more remote microphones. Sensitivity studies for the hard-surface and microphone indicated a 2.5 dB change in the relative excess attenuation for a systematic error in source and microphone elevations on the order of 1 mm. For the soft-surface model, no comparable sensitivity was found.

Parrott, Tony L.↗

An estimate of the noise shielding on the fuselage resulting from installing a short duct around an advanced propeller

A simple barrier shielding model was used to estimate the amount of noise shielding on the fuselage that could result from installing a short duct around a wing-mounted advanced propeller. With the propeller located one-third of the duct length from the inlet, estimates for the maximum blade passing tone attenuation varied from 7 dB for a duct 0.25 propeller diameter long to 16.75 dB for a duct 1 diameter long. Attenuations for the higher harmonics would be even larger because of their shorter wavelengths relative to the duct length. These estimates show that the fuselage noise reduction potential of a ducted compared with an unducted propeller is significant. Even more reduction might occur if acoustic attenuation material were installed in the duct.

Dittmar, James H.↗

Detection of bondline delaminations in multilayer structures with lossy components

The detection of bondline delaminations in multilayer structures using ultrasonic reflection techniques is a generic problem in adhesively bonded composite structures such as the Space Shuttles's Solid Rocket Motors (SRM). Standard pulse echo ultrasonic techniques do not perform well for a composite resonator composed of a resonant layer combined with attenuating layers. Excessive ringing in the resonant layer tends to mask internal echoes emanating from the attenuating layers. The SRM is made up of a resonant steel layer backed by layers of adhesive, rubber, liner and fuel, which are ultrasonically attenuating. The structure's response is modeled as a lossy ultrasonic transmission line. The model predicts that the acoustic response of the system is sensitive to delaminations at the interior bondlines in a few narrow frequency bands. These predictions are verified by measurements on a fabricated system. Successful imaging of internal delaminations is sensitive to proper selection of the interrogating frequency. Images of fabricated bondline delaminations are presented based on these studies.

Madaras, Eric I.↗

Characterization of sintered SiC by using NDE

Capabilities of projection microfocus X-radiography and of ultrasonic velocity and attenuation for characterizing silicon carbide specimens were assessed. Silicon carbide batches covered a range of densities and different microstructural characteristics. Room-temperature, four-point flexural strength tests were conducted. Fractography was used to identify types, sizes, and locations of fracture origins. Fracture toughness values were calculated from fracture strength and flaw characterization data. Detection capabilities of radiography for fracture-causing flaws were evaluated. Applicability of ultrasonics for verifying material strength and toughness was examined. Radiography proved useful in detecting high-density inclusions and isolated voids, but failed in detecting surface and subsurface agglomerates and large grains as fracture origins. Ultrasonic velocity dependency on density was evident. Attenuation dependency on density and mean pore size was clearly demonstrated. Understanding attenuation as a function of toughness was limited by shortcomings in K sub IC determination.

Baaklini, George Y.↗

Measurement and modeling of land mobile satellite propagation at UHF and L-band

A propagation experiment is described in which a stratospheric balloon served as a transmitter platform at 870 and 1502 MHz in simulation of a land mobile satellite. A vehicle followed the drifting balloon along roads of western Texas and New Mexico, collecting at L-band amplitude and phase, and at UHF amplitude information only for elevation angles between 25 and 45 deg. The data obtained have been analyzed and are presented along with results from modeling of multipath scattering and roadside tree attenuation. The signal, with variations caused by multipath propagation and tree shadowing, was reduced by 3 dB at L-band and 2 dB at UHF for one percent of all locations. A median ratio of 3.9 was found between peak-to-peak phase (degrees) and power (dB) fluctuations. The ratio between L-band and UHF dB attenuation averages varied from 1.3 to 1.0 at fade levels from 6 to 23 dB. Optical sky brightness was measured and used to predict fade distribution with great accuracy. A single-scatterer multipath model is introduced. It is used to duplicate some of the measured data and to show the dependence of power variations on satellite elevation angle. Using Fresnel diffraction theory, the attenuation caused by a model tree was calculated to be near 10 dB and the maximum fade was found to increase by the logarithm of the number of branches.

Vogel, Wolfhard J.↗

A robust signalling system for land mobile satellite services

Presented here is a signalling system optimized to ensure expedient call set-up for satellite telephony services in a land mobile environment. In a land mobile environment, the satellite to mobile link is subject to impairments from multipath and shadowing phenomena, which result in signal amplitude and phase variations. Multipath, caused by signal scattering and reflections, results in sufficient link margin to compensate for these variations. Direct signal attenuation caused by shadowing due to buildings and vegetation may result in attenuation values in excess of 10 dB and commonly up to 20 dB. It is not practical to provide a link with sufficient margin to enable communication when the signal is blocked. When a moving vehicle passes these obstacles, the link will experience rapid changes in signal strength due to shadowing. Using statistical models of attenuation as a function of distance travelled, a communication strategy has been defined for the land mobile environment.

Irish, Dale↗

Parametric study of electromagnetic waves propagating in absorbing curved S ducts

A finite-element Galerkin formulation has been developed to study attenuation of transverse magnetic (TM) waves propagating in two-dimensional S-curved ducts with absorbing walls. In the frequency range where the duct diameter and electromagnetic wave length are nearly equal, the effect of duct length, curvature (duct offset), and absorber wall thickness was examined. For a given offset in the curved duct, the length of the S-duct was found to significantly affect both the absorptive and reflective characteristics of the duct. For a straight and a curved duct with perfect electric conductor terminations, power attenuation contours were examined to determine electromagnetic wall properties associated with maximum input signal absorption. Offset of the S-duct was found to significantly affect the value of the wall permittivity associated with the optimal attenuation of the incident electromagnetic wave.

Baumeister, Kenneth J.↗

Propagation degradation for mobile satellite systems

The results of four propagation tests for mobile satellite systems, which used remotely piloted vehicles and helicopters to simulate a transmitter satellite source platform, are presented. The signal degradation by individual trees, attenuation caused by roadside trees when the vehicle was moving, and multipath effects in hilly and mountainous terrain were studied. Three tests were conducted at UHF (870 MHz) and one test was performed at UHF and L band (1500 MHz). It was found that attenuation by roadside trees is the dominant cause of signal fading. The signal degradation may amount to 7 dB or more for 10 percent of the traveling time along tree-lined roads, with attenuations of 15 dB or more 1 percent of the time. The signal degradation caused by multipath effects amounted to only about 2 dB for 10 percent of the time and 9 dB for 1 percent of the time.

Goldhirsh, Julius↗

A CCIR aeronautical mobile satellite report

Propagation effects in the aeronautical mobile-satellite service differ from those in the fixed-satellite service and other mobile-satellite services because: small antennas are used on aircraft, and the aircraft body may affect the performance of the antenna; high aircraft speeds cause large Doppler spreads; aircraft terminals must accommodate a large dynamic range in transmission and reception; and due to their high speeds, banking maneuvers, and three-dimensional operation, aircraft routinely require exceptionally high integrity of communications, making even short-term propagation effects very important. Data and models specifically required to characterize the path impairments are discussed, which include: tropospheric effects, including gaseous attenuation, cloud and rain attenuation, fog attenuation, refraction and scintillation; surface reflection (multipath) effects; ionospheric effects such as scintillation; and environmental effects (aircraft motion, sea state, land surface type). Aeronautical mobile-satellite systems may operate on a worldwide basis, including propagation paths at low elevation angles. Several measurements of multipath parameters over land and sea were conducted. In some cases, laboratory simulations are used to compare measured data and verify model parameters. The received signals is considered in terms of its possible components: a direct wave subject to atmospheric effects, and a reflected wave, which generally contains mostly a diffuse component.

Davarian, Faramaz↗

SQUID holder with high magnetic shielding

A SQUID holder designed for high magnetic shielding is discussed. It is shown how to estimate the attenuation of the magnetic field from the normal magnetic modes for an approximate geometry. The estimate agrees satisfactorily with the attenuation measured with a commercial RF SQUID installed in the holder. The holder attenuates external magnetic fields by more than 10 to the 9th at the SQUID input. With the SQUID input shorted, the response to external fields is 0.00001 Phi(0)/G.

Rigby, K. W.↗

Propagation experiments at Virginia Tech with the Olympus satellite

A major propagation experiment is in progress to measure atmospheric attenuation at 12, 20, and 30 GHz using the beacons of the Olympus satellite. The experiment uses a frequency-locked receiver system which locks to the 12-GHz beacon frequency and measures the signal strength of the coherent 20- and 30-GHz beacons in a 3-Hz bandwidth. The receiving system is augmented with radiometers in each beacon frequency band to set the clear-air attenuation levels of the beacon signals. Olympus propagation experiment objectives and the measurement system are described. Results from the measurement program will include fade statistics at all frequencies, attenuation scaling between frequencies, short baseline site diversity, and fade dynamics.

Pratt, T.↗

Polarization radar measurements in rain at 5 and 9 GHz

Potential techniques for measuring rainfall rate R and rainwater content W at 9 and 5 GHz are explored. An investigation is made of a previous technique to use the polarization propagation differential phase shift with increasing distance from the radar Phi(H-V) to estimate and remove the effects of specific and polarization differential attenuation from Z(H) and Z(DR), respectively. It is shown that in rain this technique is sensitive to variations in the drop-size distribution. It is confirmed that Phi(H-V) can be used to extend the distance over which useful measurements of Z(H) and Z(DR) can be obtained. While residual errors introduced by attenuation and the 'noise' from the correction scheme itself eclipse the potential of many possible techniques for quantitative rainfall measurements at these frequencies, the attenuation recovery scheme is argued to be adequate for obtaining useful polarization microphysical measurements, particularly above the melting level, even after encounters with rain.

Jameson, A. R.↗

Ultrasonic sensing of porous granular media

The existence of phenomena for sensing porosity and grain growth in powder metallurgical processes using ultrasonic techniques is demonstrated. Ultrasonic velocity is a strong function of pore concentration and provides a potential means for in situ measurement of this quantity. Ultrasonic attenuation, measured in the low megahertz range, depends on grain size and pore content. When velocity data and a scattering theory are used to account for the attenuation due to pores, attenuation data may be used to infer the grain size. Predictions of existing scattering theories are compared with experimental observations, and substantial disagreements are attributed to modeling inadequacies.

Parthasarathi, Sanjai↗

Dynamic rain fade compensation techniques for the advanced communications technology satellite

The dynamic and composite nature of propagation impairments that are incurred on earth-space communications links at frequencies in and above the 30/20 GHz Ka band necessitate the use of dynamic statistical identification and prediction processing of the fading signal in order to optimally estimate and predict the levels of each of the deleterious attenuation components. Such requirements are being met in NASA's Advanced Communications Technology Satellite (ACTS) project by the implementation of optimal processing schemes derived through the use of the ACTS Rain Attenuation Prediction Model and nonlinear Markov filtering theory. The ACTS Rain Attenuation Prediction Model discerns climatological variations on the order of 0.5 deg in latitude and longitude in the continental U.S. The time-dependent portion of the model gives precise availability predictions for the 'spot beam' links of ACTS. However, the structure of the dynamic portion of the model, which yields performance parameters such as fade duration probabilities, is isomorphic to the state-variable approach of stochastic control theory and is amenable to the design of such statistical fade processing schemes which can be made specific to the particular climatological location at which they are employed.

Manning, Robert M.↗

A satellite-borne radar wind sensor (RAWS)

Modeling global atmospheric circulations and forecasting the weather would improve if worldwide information on winds aloft were available. Accurate prediction of weather is important to agriculture, shipping, air traffic, and many other fields. Global system models of climate are of great importance. Current global atmospheric models use pressure measurements and thermodynamic properties to calculate the effects of wind for use in Numerical Weather Prediction (NWP) models. Inputs to the NWP models are temperature, pressure and wind velocities at different heights. Clearly direct wind measurements could significantly improve the NWP model performance. The RAdar Wind Sounder (RAWS) program at the University of Kansas is a study of the feasibility and the trade-offs in the design of a space-based radar system to measure wind vectors. This can be done by measuring the Doppler shift of cloud and rain returns from three or more points and calculating the components of the wind vector. The RAWS study to date uses the candidate system selected after preliminary study of frequencies and sensitivities. Two frequencies chosen, 10 and 35 GHz, allow higher sensitivity for clouds and more penetration for rain. The past year was devoted to modeling the signal-to-noise ratio (SNR) achievable for the two frequencies. The determination of SNR versus cloud penetration depth used a cloud backscattering and attenuation model in the appropriate radar equation. Calculations assumed reasonable losses in reception and transmission, in addition to the atmospheric attenuation. We discovered that ice clouds provide a higher SNR than previously calculated, but some water clouds give lower SNRs than we calculated before. One of the primary issues in the SNR calculation was the choice of the drop size distribution. Although Xin used several distributions (e.g., log normal, Khrigian and Mazin), this year we used the Deirmendjian cloud model. SNR versus cloud penetration plots were generated to validate the candidate system. Rain, which appears in the cloud models at the lower altitudes, provides ample SNR, as do the higher clouds composed of ice particles. However, in some cloud situations we found the sensitivity for the clouds was marginal or inadequate. At 35 GHz, two of the cloud models characterized by 1 to 2 g/cu m of water content at altitudes extending from 150 to 1500 meters, produced a sufficient SNR. Other models, however, with water contents ranging from 0.5 to 4 g/cu m and altitudes up to 4000 meters, exhibit SNR of -3 to -23 dB, largely because of attenuation in the upper cloud layers. These results coupled with the lower SNR at 10 GHz, led to an investigation of alternate frequencies. The rain present beneath these clouds provides adequate SNR at 10 GHz, and in most cases, at GHz.

Moore, Richard K.↗

Mechanical stimulation of skeletal muscle mitigates glucocorticoid induced decreases in prostaglandin synthesis

The glucocorticoid dexamethasone (Dex) induces a decline in protein synthesis and protein content of tissue cultured, avian skeletal muscle cells, and this atrophy is attenuated by repetitive mechanical stretch. Since the prostaglandin synthesis inhibitor indomethacin mitigated this stretch attenuation of muscle atrophy, the role of prostaglandins as growth modulators in these processes was examined. Dex at 10(exp -8) M reduced PGF(sub 2(alpha)) production 55 percent - 65 percent and PGE(sub 2) production 84 - 90 percent after 24 - 72 h of incubation in static cultures. Repetitive 10 percent stretch-relaxations of the non-Dex treated cultures increased PGF(sub 2(alpha)) efflux 41 percent at 24 h and 276 percent at 72 h and increased PGE(sub 2) production 51 percent at 24 h and 236 percent at 72 h. Mechanical stimulation of Dex treated cultures increased PGF(sub 2(alpha)) production 162 percent after 24 h, thus returning PGF(sub 2(alpha)) efflux to the level of non-Dex treated cultures. At 72 h, stretch increased PGF(sub 2(alpha)) efflux 65 percent in Dex treated cultures, but PGF(sub 2(alpha)) production was 45-84 percent less than non-Dex treated cultures. Mechanical stimulation of Dex treated cultures increased PGE(sub 2) production at 24 h, but not at 72 h. Dex reduced prostaglandin H synthase (PGHS) activity in the muscle cultures by 70 percent after 8 - 24 h of incubation, and mechanical stimulation increased PGHS activity of the Dex treated cultures by 98 percent. It is concluded that repetitive mechanical stimulation attenuates the catabolic effects of Dex on cultured skeletal muscle cells in part by reversing the Dex-induced declines in PGHS activity and prostaglandin production.

Chromiak, Joseph A.↗