SEARCH · Engineering Papers

Results for “Wake Vortex”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

All sources NASA NTRS DOE OSTI

NASA NTRS1989

Propeller/wing interaction

The present experimental investigation of the steady-state and unsteady-state effects due to the interaction between a tractor propeller's wake and a wing employs, in the steady case, wind tunnel measurements at low subsonic speed; results are obtained which demonstrate wing performance response to variations in configuration geometry. Other steady-state results involve the propeller-hub lift and side-force due to the wing's influence on the propeller. The unsteady effects of interaction were studied through flow visualization of propeller-tip vortex distortion over a wing, again using a tractor-propeller configuration.

Witkowski, David P.↗

NASA NTRS1975

NASA/FRC wake turbulence flight test program: Ride quality aspects

To determine how much the ride quality of the Shuttle Carrier (Boeing 747) Aircraft is affected at various spoiler settings, the PEMS II (Portable Environmental Measuring System) was used to measure onboard motion during a test flight October 15, 1975. The PEMS II measures acceleration in the vertical, transverse and longitudinal directions as well as angular rates of pitch, roll, and yaw. The data acquired by this instrument, combined with an airline passenger comfort model, gives an indication of how passengers would react to the motion induced by flying in a vortex alleviation configuration.

Deptula, D. A.↗

NASA NTRS1974

Experimental investigation of model variable-geometry and ogee tip rotors

An experimental investigation was conducted to systematically explore the effects of inter-blade spatial relationships and pitch variations on rotor performance and wake geometry. Variable-geometry rotors consisting of various combinations of blade length, axial spacing, azimuth spacing, and collective pitch were tested at model scale in hover and forward flight. In addition, a hover test of a model rotor with an ogee blade tip design was conducted to determine its performance and wake characteristics. The results of this investigation indicate that properly selected variable geometry rotor configurations can offer substantial improvements in hover performance without adversely affecting forward flight performance. Axial spacing of alternate blades was found to provide the greatest performance benefit, and further improvements were achieved by combining azimuth spacing with axial spacing. The performance benefit appears to be related to the relief of local adverse aerodynamic phenomena produced by vortex interference. The ogee tip design was found to substantially reduce the concentrated core intensity of the tip vortex, and could thus prove beneficial for the relief of blade-vortex interaction problems. However, the ogee tip was found to reduce hover performance at model scale.

Landgrebe, A. J.↗

NASA NTRS2000

A Novel Method for Reducing Rotor Blade-Vortex Interaction

One of the major hindrances to expansion of the rotorcraft market is the high-amplitude noise they produce, especially during low-speed descent, where blade-vortex interactions frequently occur. In an attempt to reduce the noise levels caused by blade-vortex interactions, the flip-tip rotor blade concept was devised. The flip-tip rotor increases the miss distance between the shed vortices and the rotor blades, reducing BVI noise. The distance is increased by rotating an outboard portion of the rotor tip either up or down depending on the flight condition. The proposed plan for the grant consisted of a computational simulation of the rotor aerodynamics and its wake geometry to determine the effectiveness of the concept, coupled with a series of wind tunnel experiments exploring the value of the device and validating the computer model. The computational model did in fact show that the miss distance could be increased, giving a measure of the effectiveness of the flip-tip rotor. However, the wind experiments were not able to be conducted. Increased outside demand for the 7'x lO' wind tunnel at NASA Ames and low priority at Ames for this project forced numerous postponements of the tests, eventually pushing the tests beyond the life of the grant. A design for the rotor blades to be tested in the wind tunnel was completed and an analysis of the strength of the model blades based on predicted loads, including dynamic forces, was done.

Glinka, A. T.↗

NASA NTRS1986

An experimental investigation of vortex breakdown on a delta wing

An experimental investigation of vortex breakdown on delta wings at high angles is presented. Thin delta wings having sweep angles of 70, 75, 80 and 85 degrees are being studied. Smoke flow visualization and the laser light sheet technique are being used to obtain cross-sectional views of the leading edge vortices as they break down. At low tunnel speeds (as low as 3 m/s) details of the flow, which are usually imperceptible or blurred at higher speeds, can be clearly seen. A combination of lateral and longitudinal cross-sectional views provides information on the three dimensional nature of the vortex structure before, during and after breakdown. Whereas details of the flow are identified in still photographs, the dynamic characteristics of the breakdown process were recorded using high speed movies. Velocity measurements were obtained using a laser Doppler anemometer with the 70 degree delta wing at 30 degrees angle of attack. The measurements show that when breakdown occurs the core flow transforms from a jet-like flow to a wake-like flow.

Payne, F. M.↗

NASA NTRS1992

Vorticity generation mechanisms in parallel injection schemes for supersonic mixing

A numerical study is reported of the three-dimensional nonreacting supersonic flow field produced by three parallel fuel injection schemes. Such injections are being considered as a means of enhancing fuel mixing in future Scramjet engine designs. The strength of vortex structures produced by ramp injectors and by rocket/jet interactions are quantified and their relative effectiveness in enhancing the fuel mixing process is addressed. An experimental setup for validation of the above numerical results has been constructed and preliminary results are presented. For the flow field parameters chosen, the ramp generated vorticity is found to be considerably larger than that generated by the shock. The unsteady recirculating flow field in the wake of the injector appears also to give rise to important additional vorticity and mixing.

Donohue, James M.↗

NASA NTRS1998

Inviscid Interactions Between Wake Vortices and Shear Layers

Aircraft trailing vortices can be influenced significantly by atmospheric conditions such as crosswind, turbulence, and stratification. According to the NASA 1994 and 1995 field measurement program in Memphis, Tennessee, the descending aircraft wake vortices could stall or be deflected at the top of low-level temperature inversions that usually produce pronounced shear zones. Numerical simulations of vortex/shear interactions with ground effects have been performed by several groups. Burnham used a series of evenly spaced line vortices at a particular altitude to model the ground shear layer of the cross- wind. He found that the wind shear was swept up around the downwind vortex and caused the downwind vortex to move upward, and claimed that the effect was actually produced by the vertical gradient in the wind shear rather than by the wind shear directly, because uniformly distributed wind-shear vortices would have no effect on the trailing vortex vertical motion. Recently, Proctor et al. numerically tested the effects of narrow shear zones on the behavior of the vortex pair, motivated by the observation of the Memphis field data. The shear-layer sensitivity tests indicated that the downwind vortex was more sensitive and deflected to a higher altitude than its upwind counterpart. The downstream vortex contained vorticity of opposite sign to that of the shear. There was no detectable preference for the downwind vortex (or upwind vortex) to weaken (or strengthen) at a greater rate.

Zheng, Z. C.↗

NASA NTRS1979

Water tunnel visualization of the vortex flows of the F-15

Flow visualization studies were conducted in a diagnostic water tunnel to provide details of the wing, glove, and forebody vortex flow fields of the F-15 aircraft over a range of angles of attack and sideslip. Both the formation and breakdown of the vortex flow as a function of angle of attack and sideslip are detailed for the basic aircraft configuration. Additional tests showed that the wing upper surface vortex flows were sensitive to variations in an inlet mass flow ratio and an inlet cowl deflection angle. Two lengthened forebodies, one with a modified cross-sectional shape, were tested in addition to the basic forebody. Asymmetric forebody vortices were observed at zero sideslip and high angles of attack on each forebody. A large nose boom was added to each of the three forebodies, and it was observed that the turbulent wake shed from the boom disrupted the forebody vortices.

Lorincz, D. J.↗

DOE OSTI2019

Adaptive harnessing damping in hydrokinetic energy conversion by two rough tandem-cylinders using flow-induced vibrations

Alternating lift technology (ALT) harnesses hydrokinetic energy from currents and tides and is different from conventional steady lift technologies (turbines). ALT is still under development with an important research issue being the mitigation of wake effect on downstream cylinders in Flow Induced Oscillations (FIO) of multi-cylinder Current Energy Converters (CEC). Rather than adjust the configuration/parameters of the converter, a more direct and effective way is to actively adjust the harnessed power. In this paper, a hydrokinetic energy converter using FIO of two cylinders in tandem in one-degree-of-freedom oscillators, with nonlinear adaptive damping and linear spring stiffness, is tested experimentally. FIO include Vortex Induced Vibrations (VIV), galloping, and their coexistence. Introducing adaptive damping into the tandem cylinders overcomes the shielding effect, which previous research on two tandem cylinders has shown to reduce power output by the downstream cylinder. Shielding along with fixed damping result either in ceasing motion due to excessive damping, or in low harnessed energy due to insufficient damping. In this experimental study, damping-to-velocity rate, linear spring-stiffness, cylinder spacing, and flow-velocity are the parameters with Reynolds number 30,000 ≤ Re ≤ 120,000. Comparison to linear-oscillators in FIO shows that this nonlinear converter, with velocity-proportional damping coefficient, is more effective over the entire FIO range but especially in galloping, where both flow and cylinder speeds are higher. Experimental results for energy harvesting, efficiency and instantaneous energy of the converter are presented and discussed supported by amplitude and frequency response data. Here the results show that the nonlinear, adaptive, velocity-proportional damping coefficient is an effective way to increase the overall harnessed power and the power of downstream cylinder. The harnessed power in the VIV to galloping transition increases by up to 94%. The most significant improvement is in the galloping region, where the increase in harnessed power and efficiency is around 33%.

13 HYDRO ENERGY↗

NASA NTRS1979

Data and analysis procedures for improved aerial applications mission performance

An analysis procedure is given and cases analyzed for the effects of wing geometry on lateral transport of a variety of agricultural particles released in the wake of an agricultural airplane. The cases analyzed simulate the release of particles from a fuselage centerline-mounted dry material spreader; however, the procedure applies to particles released anywhere along the wing span. Consideration is given to the effects of taper ratio, aspect ratio, wing loading, and deflected flaps. It is noted that significant lateral transport of large particles can be achieved using high-lift devices positioned to create a strong vortex near the location of particle release.

Holmes, B. J.↗

NASA NTRS1981

A vortex-lattice method for calculating longitudinal dynamic stability derivatives of oscillating delta wings

A nonsteady vortex-lattice method is introduced for predicting the dynamic stability derivatives of a delta wing undergoing an oscillatory motion. The analysis is applied to several types of small oscillations in pitch. The angle of attack varied between + or - 1 deg, with the mean held at 0 deg when the flow was assumed to be attached and between + or - 1 deg and the mean held at 15 deg when both leading-edge separation and wake roll-up were included. The computed results for damping in pitch are compared with several other methods and with experiments, and are found to be consistent and in good agreement.

Levin, D.↗

NASA NTRS1976

Aviation safety research and transportation/hazard avoidance and elimination

Data collected by the Scanning Laser Doppler Velocimeter System (SLDVS) was analyzed to determine the feasibility of the SLDVS for monitoring aircraft wake vortices in an airport environment. Data were collected on atmospheric vortices and analyzed. Over 1600 landings were monitored at Kennedy International Airport and by the end of the test period 95 percent of the runs with large aircraft were producing usable results in real time. The transport was determined in real time and post analysis using algorithms which performed centroids on the highest amplitude in the thresholded spectrum. Making use of other parameters of the spectrum, vortex flow fields were studied along with the time histories of peak velocities and amplitudes. The post analysis of the data was accomplished with a CDC-6700 computer using several programs developed for LDV data analysis.

Sonnenschein, C. M.↗

NASA NTRS1980

Influence of rotor blade tip shape on tip vortex shedding - An unsteady, inviscid analysis

An unsteady potential flow panel method is described based on a time-stepping procedure and using planar quadrilateral panels to represent the surface of thick blades. Each panel has a constant source and doublet distribution and a central control point where an internal Dirichlet boundary condition is applied. The method includes detail paneling around the tip edge and offers the facility of prescribing a tip-edge separation. Preliminary results are shown for four blade tip shapes which are treated as semi-span wings oscillating in pitch about a mean angle of attack of 6 deg. Further work is planned for the wake model before proceeding to higher angles of attack.

Maskew, B.↗

NASA NTRS1990

Calculations of the flow past bluff bodies, including tilt-rotor wing sections at alpha = 90 deg

An attempt was made to model in two dimensions the effects of rotor downwash on the wing of the tilt-rotor aircraft and to compute the drag force on airfoils at - 90 deg angle of attack, using a well-established Navier-Stokes code. However, neither laminar nor turbulent calculations agreed well with drag and base-pressure measurements at high Reynolds numbers. Therefore, further efforts were concentrated on bluff-body flows past various shapes at low Reynolds numbers, where a strong vortex shedding is observed. Good results were obtained for a circular cylinder, but the calculated drag of a slender ellipse at right angles to the freestream was significantly higher than experimental values reported in the literature for flat plates. Similar anomalous results were obtained on the tilt-rotor airfoils, although the qualitative effects of flap deflection agreed with the wind tunnel data. The ensemble of results suggest that there may be fundamental differences in the vortical wakes of circular cylinders and noncircular bluff bodies.

Raghavan, V.↗

DOE OSTI2020

Lift Equivalence and Cancellation for Airfoil Surge–Pitch–Plunge Oscillations

A NACA 0018 airfoil in freestream velocity is oscillated in longitudinal, transverse, and angle-of-attack directions with respect to the freestream velocity, known as surge, plunge, and pitch. The lift-based equivalence method introduces phase shifts between these three motions to construct in-phase sinusoidal components for maximum lift, waveform construction. Lift cancellation is also determined with the exact negative pitch and plunge motion amplitudes found from the equivalence method to achieve out-of-phase wave destruction. Lift cancellation occurs when a combination of these motions is sought to obtain a constant lift magnitude throughout the oscillation cycle. To achieve both equivalence and cancellation of lift, a prescribed pure pitch amplitude through the Theodorsen theory equates the corresponding equivalent plunge amplitude and pitch–plunge phase shift. These Theodorsen, linear superposition findings of pitch–plunge are leveraged toward the Greenberg theory to determine a closed-form, surge–pitch–plunge solution through the addition of a surge–plunge phase shift and optimal surge amplitude for lift cancellation. The lift cancellation surge–pitch–plunge amplitudes define the equivalence amplitude investigated here and theoretically limit the experiment to combinations of the first lift harmonic of the Greenberg theory. The analytical results are then compared with experimental lift force measurements and dye visualization. Finally, the normalized lift differences due to unsteady wake and boundary-layer behavior are examined to explore the extents of the Greenberg theory for these cases of lift-based equivalence and cancellation.

42 ENGINEERING↗

NASA NTRS1986

Progress towards a model to describe jet/aerodynamic-surface interference effects

A first generation model is presented which relates the pressure distribution on an aerodynamic surface to properties of the jet plume. The characteristics of a jet in a cross flow are of primary importance in determining the pressure distribution on the aerodynamic surface and are assumed to be (1) a pair of contrasting vortices associated with a jet in a crossflow, (2) entrainment of crossflow fluid into the jet plume, and (3) a wake region near the aerodynamic surface and extending downstream from the jet orifice. The model is applied to the configuration of a round jet exhausting perpendicularly through a flat plate into a uniform crossflow for a range of jet-to-crossflow velocity ratios from three to ten. It is demonstrated that the model is capable of describing the measured pressure distribution on the flat plate with model parameters that are compatable with the incomplete description of the vortex pair that is available. The fore and moments on one plate are presented as functions of jet-to-crossflow velocity ratios.

Fearn, R. L.↗

NASA NTRS1994

Flow-visualization study of the X-29A aircraft at high angles of attack using a 1/48-scale model

A water-tunnel study on a 1/48-scale model of the X-29A aircraft was performed at the NASA Dryden Flow Visualization Facility. The water-tunnel test enhanced the results of the X-29A flight tests by providing flow-visualization data for comparison and insights into the aerodynamic characteristics of the aircraft. The model was placed in the water tunnel at angles of attack of 20 to 55 deg. and with angles of sideslip from 0 to 5 deg. In general, flow-visualization techniques provided useful information on vortex formation, separation, and breakdown and their role in yaw asymmetries and tail buffeting. Asymmetric forebody vortices were observed at angles of attack greater than 30 deg. with 0 deg. sideslip and greater than 20 deg. with 5 deg. sideslip. While the asymmetric flows observed in the water tunnel did not agree fully with the flight data, they did show some of the same trends. In addition, the flow visualization indicated that the interaction of forebody vortices and the wing wake at angles of attack between 20 and 35 deg. may cause vertical-tail buffeting observed in flight.

Cotton, Stacey J.↗

NASA NTRS1989

Direct numerical simulations of transition in a compressible wake

Direct numerical simulations of a compressible wake are performed to determine the sensitivity of large-scale motions to initial phase lags between the most unstable two-dimensional wave and a pair of oblique waves, and to determine the effect of Mach number on the development of three-dimensional motions. The vorticity dynamics of the flow are studied, and it is determined that, depending upon the initial phase lag, the interaction of the streamwise vorticity with the spanwise vortices may result in the formation of closed vortex loops, or in the removal of streamwise vorticity from the saddle region between the spanwise vortices. Due to lower growth rates experienced at high Mach numbers, the roll-up process is delayed, and the resultant nonlinear motions are much more diffuse.

Chen, Jacqueline H.↗